- 20 Jan, 2017 6 commits
-
-
Enric Balletbo i Serra authored
Add support for the ISL29023 ALS connected via the I2C bus. Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Enric Balletbo i Serra authored
Add support for the 16-Bit I/O Expander connected via the I2C bus. Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Enric Balletbo i Serra authored
Add support for the BQ32000 Real Time Clock connected to the I2C bus and disable the AM335x Real Time Clock. Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Enric Balletbo i Serra authored
Add support for the 32Mb Serial Flash Memory connected to SPI0 and using CS1. Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Enric Balletbo i Serra authored
The UART1 is connected to the infrared (IR) receiver module, so enable it to be able to comunicate with it. Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Enric Balletbo i Serra authored
I2C1 is not used so remove it in order to avoid conflicts. Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 12 Jan, 2017 5 commits
-
-
Ladislav Michl authored
FDT harcoded partition table does not match that one in historical TI's 2.6.37 kernel and non legacy kernels even use different ECC scheme, yet noone complained, so remove it altogether. Also, UBI volumes instead of partitions are used since u-boot-2016.09. Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Grygorii Strashko authored
According to errata i880 description the speed of Ethernet port 1 on AM572x SoCs rev 1.1 should be limited to 10/100Mbps, because RGMII2 Switching Characteristics are not compatible with 1000 Mbps operation [1]. The issue is fixed with Rev 2.0 silicon. Hence, rework Beagle-X15 and Begale-X15-revb1 to use phy-handle instead of phy_id and apply corresponding limitation to the Ethernet Phy 1. [1] http://www.ti.com/lit/er/sprz429j/sprz429j.pdfSigned-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Teresa Remmet authored
As the bootloader passes the NAND and the SPI flash partition tables there is no need to keep them in the kernel device tree. Removed them. Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Grygorii Strashko authored
TI DRA72-EVM Rev C has two DP83867 ethernet phys which support IRQ generation in case of phy/link status changes. The INT/PWDN lines from both DP83867 phys are wired to DRA7 gpio6.16, so reflect the same in DT. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
This prevents having to poll peripheral USB port cable status. Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 06 Jan, 2017 4 commits
-
-
Tony Lindgren authored
This is slightly different wiring compared to omap5-uevm or pandaboard: /sys/bus/usb/devices/3-2 hub /sys/bus/usb/devices/3-2.3 7500 Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
Note that with 9730 the wiring is different compared to 9514 found on beagleboard xm for example. On beagleboard xm we have: /sys/bus/usb/devices/1-2 hub /sys/bus/usb/devices/1-2.1 9514 While on omap5-uevm we have: /sys/bus/usb/devices/1-2 hub /sys/bus/usb/devices/1-3 9730 Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
Inspired by a patch for beagleboard xm by Laurent Pinchart <laurent.pinchart@ideasonboard.com>, similar patch also works for pandaboard. The only difference is that the hub is address 1 instead of 2. Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Laurent Pinchart authored
The Beagleboard-xM has a LAN9514 USB hub and ethernet controller, connected to port 2 of the OMAP EHCI controller. The board however has no EEPROM to store the ethernet MAC address, which is programmed by the boot loader. To allow Linux to use the same MAC address as the boot loader (or for that matter any fixed MAC address), we need a node in the device tree for the ethernet controller that the boot loader can update at runtime with a local-mac-address property. Add it, along with an alias for the ethernet controller to let the boot loader locate it easily. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 05 Jan, 2017 11 commits
-
-
Teresa Remmet authored
Update ethernet phy1 node to use phy-handle now. Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Teresa Remmet authored
Update ethernet phy0 node to use phy-handle now. Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Teresa Remmet authored
Set USB0 to otg mode (default) and not fix to peripheral. As it can be used in host mode also. Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Teresa Remmet authored
Include the i2c temperature sensor which is optionaly mounted on the phyCORE-AM335x-R2 module. Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Teresa Remmet authored
As we may have different SPI NOR flashes with 8MB populated on phyCORE-AM335x SOM, set the "jedec,spi-nor" SPI Flash compatible string. Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Mark Jackson authored
From v4.2+ the GPMC code has been changed to reset all the bootloader GPMC settings when the kernel starts. As such, this DTS file now needs the external FRAM defined. Signed-off-by: Mark Jackson <mpfj@newflow.co.uk> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Sekhar Nori authored
For the existing IOdelay configuration via U-Boot, NAND is not supported on dra72-evm (both Rev B and Rev C). Disable it. Commit 46cfc894 ("ARM: dts: dra72-evm: Remove pinmux configurations for erratum i869") has already removed pinmuxing for NAND making it unusable. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Kishon Vijay Abraham I authored
Add pinmux configuration for SD card slot and eMMC device found on TI's DRA74x EVM. Only the default modes are supported. For higher speed modes (UHS and HS200) to function, we need full fledged IODelay support in kernel. IODelay support is yet to be added. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> [nsekhar@ti.com: rebase to mainline/master, use IOPAD() macro, update commit message] Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Sekhar Nori authored
Pinmuxing for DRA7x/AM57x family of processors need to be done in IO isolation as part of initial bootloader executed from SRAM. This is done as part of iodelay configuration sequence and is required due to the limitations introduced by erratum ID: i869[1] (IO Glitches can occur when changing IO settings) and elaborated in the Technical Reference Manual[2] 18.4.6.1.7 Isolation Requirements. Only peripheral that is permitted for dynamic pin mux configuration is MMC and DCAN. MMC is permitted to change to accommodate the requirements for varied speeds (which require IO-delay support in kernel as well). DCAN is a result of i893[1] (DCAN initialization sequence). DCAN pinmux is retained in this patch. MMC pinmux is missing from the dra7-evm.dts file and the board is relying on configuration done by bootloader. A subsequent patch will add MMC pinmux configuration. A side-effect of this patch is that NAND support is removed. NAND pins clash with VOUT3 on DRA7-EVM. U-Boot selects VOUT3 over NAND as per TI EVM application needs. [1] http://www.ti.com/lit/pdf/sprz429 [2] http://www.ti.com/lit/pdf/sprui30Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Marcin Niestroj authored
On chiliSOM TPS65217 nWAKEUP pin is connected to AM335x internal RTC EXT_WAKEUP input. In RTC-only state TPS65217 is notifying about power on events (such as power buton presses) by setting nWAKEUP output low. After that it waits 5s for proper device boot. Currently it doesn't happen, as the processor doesn't listen for such events. Consequently TPS65217 changes state from SLEEP (RTC-only state) to OFF. Enable EXT_WAKEUP input of AM335x's RTC, so the processor can properly detect power on events and recover immediately from RTC-only states, without powering off RTC and losing time. Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Pavel Machek authored
Fix GPIO comment to be consistent with rest of file and add comment what tpa6130 is. Signed-off-by: Pavel Machek <pavel@ucw.cz> Reviewed-By: Sebastian Reichel <sre@kernel.org> Reviewed-By: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 03 Jan, 2017 2 commits
-
-
Robert Nelson authored
SeeedStudio BeagleBone Green Wireless (BBGW) is an expansion of the SeeedStudio Green (BBG) with the Ethernet replaced by a TI wl1835 wireless module. This board can be indentified by the GW1x value after A335BNLT (BBB) in the at24 eeprom: GW1x [aa 55 33 ee 41 33 33 35 42 4e 4c 54 47 57 31 41 |.U3.A335BNLTGW1A|] http://beagleboard.org/green-wireless http://wiki.seeed.cc/BeagleBone_Green_Wireless/ firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware wl18xx mac address: Stored in at24 eeprom at address 5-16: hexdump -e '8/1 "%c"' /sys/bus/i2c/devices/0-0050/eeprom | cut -b 5-16 Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tony Lindgren <tony@atomide.com> CC: Jason Kridner <jkridner@beagleboard.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Robert Nelson authored
This is going to be shared with the SeeedStudio BeagleBone Green Wireless Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tony Lindgren <tony@atomide.com> CC: Jason Kridner <jkridner@beagleboard.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 02 Jan, 2017 2 commits
-
-
Robert Nelson authored
BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with the Ethernet replaced by a TI wl1835 wireless module. This board can be indentified by the BWAx value after A335BNLT (BBB) in the at24 eeprom: BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|] http://beagleboard.org/black-wireless https://github.com/beagleboard/beaglebone-black-wireless firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tony Lindgren <tony@atomide.com> Acked-by: Jason Kridner <jkridner@beagleboard.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Robert Nelson authored
This is going to be shared with the BeagleBone Black Wireless Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tony Lindgren <tony@atomide.com> CC: Jason Kridner <jkridner@beagleboard.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 26 Dec, 2016 2 commits
-
-
Linus Torvalds authored
-
Larry Finger authored
I am getting the following warning when I build kernel 4.9-git on my PowerBook G4 with a 32-bit PPC processor: AS arch/powerpc/kernel/misc_32.o arch/powerpc/kernel/misc_32.S:299:7: warning: "CONFIG_FSL_BOOKE" is not defined [-Wundef] This problem is evident after commit 989cea5c ("kbuild: prevent lib-ksyms.o rebuilds"); however, this change in kbuild only exposes an error that has been in the code since 2005 when this source file was created. That was with commit 9994a338 ("powerpc: Introduce entry_{32,64}.S, misc_{32,64}.S, systbl.S"). The offending line does not make a lot of sense. This error does not seem to cause any errors in the executable, thus I am not recommending that it be applied to any stable versions. Thanks to Nicholas Piggin for suggesting this solution. Fixes: 9994a338 ("powerpc: Introduce entry_{32,64}.S, misc_{32,64}.S, systbl.S") Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
- 25 Dec, 2016 8 commits
-
-
Linus Torvalds authored
The timer type simplifications caused a new gcc warning: drivers/base/power/domain.c: In function ‘genpd_runtime_suspend’: drivers/base/power/domain.c:562:14: warning: ‘time_start’ may be used uninitialized in this function [-Wmaybe-uninitialized] elapsed_ns = ktime_to_ns(ktime_sub(ktime_get(), time_start)); despite the actual use of "time_start" not having changed in any way. It appears that simply changing the type of ktime_t from a union to a plain scalar type made gcc check the use. The variable wasn't actually used uninitialized, but gcc apparently failed to notice that the conditional around the use was exactly the same as the conditional around the initialization of that variable. Add an unnecessary initialization just to shut up the compiler. Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull timer type cleanups from Thomas Gleixner: "This series does a tree wide cleanup of types related to timers/timekeeping. - Get rid of cycles_t and use a plain u64. The type is not really helpful and caused more confusion than clarity - Get rid of the ktime union. The union has become useless as we use the scalar nanoseconds storage unconditionally now. The 32bit timespec alike storage got removed due to the Y2038 limitations some time ago. That leaves the odd union access around for no reason. Clean it up. Both changes have been done with coccinelle and a small amount of manual mopping up" * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: ktime: Get rid of ktime_equal() ktime: Cleanup ktime_set() usage ktime: Get rid of the union clocksource: Use a plain u64 instead of cycle_t
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull SMP hotplug notifier removal from Thomas Gleixner: "This is the final cleanup of the hotplug notifier infrastructure. The series has been reintgrated in the last two days because there came a new driver using the old infrastructure via the SCSI tree. Summary: - convert the last leftover drivers utilizing notifiers - fixup for a completely broken hotplug user - prevent setup of already used states - removal of the notifiers - treewide cleanup of hotplug state names - consolidation of state space There is a sphinx based documentation pending, but that needs review from the documentation folks" * 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: irqchip/armada-xp: Consolidate hotplug state space irqchip/gic: Consolidate hotplug state space coresight/etm3/4x: Consolidate hotplug state space cpu/hotplug: Cleanup state names cpu/hotplug: Remove obsolete cpu hotplug register/unregister functions staging/lustre/libcfs: Convert to hotplug state machine scsi/bnx2i: Convert to hotplug state machine scsi/bnx2fc: Convert to hotplug state machine cpu/hotplug: Prevent overwriting of callbacks x86/msr: Remove bogus cleanup from the error path bus: arm-ccn: Prevent hotplug callback leak perf/x86/intel/cstate: Prevent hotplug callback leak ARM/imx/mmcd: Fix broken cpu hotplug handling scsi: qedi: Convert to hotplug state machine
-
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linuxLinus Torvalds authored
Pull turbostat updates from Len Brown. * 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: tools/power turbostat: remove obsolete -M, -m, -C, -c options tools/power turbostat: Make extensible via the --add parameter tools/power turbostat: Denverton uses a 25 MHz crystal, not 19.2 MHz tools/power turbostat: line up headers when -M is used tools/power turbostat: fix SKX PKG_CSTATE_LIMIT decoding tools/power turbostat: Support Knights Mill (KNM) tools/power turbostat: Display HWP OOB status tools/power turbostat: fix Denverton BCLK tools/power turbostat: use intel-family.h model strings tools/power/turbostat: Add Denverton RAPL support tools/power/turbostat: Add Denverton support tools/power/turbostat: split core MSR support into status + limit tools/power turbostat: fix error case overflow read of slm_freq_table[] tools/power turbostat: Allocate correct amount of fd and irq entries tools/power turbostat: switch to tab delimited output tools/power turbostat: Gracefully handle ACPI S3 tools/power turbostat: tidy up output on Joule counter overflow
-
Nicholas Piggin authored
Add a new page flag, PageWaiters, to indicate the page waitqueue has tasks waiting. This can be tested rather than testing waitqueue_active which requires another cacheline load. This bit is always set when the page has tasks on page_waitqueue(page), and is set and cleared under the waitqueue lock. It may be set when there are no tasks on the waitqueue, which will cause a harmless extra wakeup check that will clears the bit. The generic bit-waitqueue infrastructure is no longer used for pages. Instead, waitqueues are used directly with a custom key type. The generic code was not flexible enough to have PageWaiters manipulation under the waitqueue lock (which simplifies concurrency). This improves the performance of page lock intensive microbenchmarks by 2-3%. Putting two bits in the same word opens the opportunity to remove the memory barrier between clearing the lock bit and testing the waiters bit, after some work on the arch primitives (e.g., ensuring memory operand widths match and cover both bits). Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Bob Peterson <rpeterso@redhat.com> Cc: Steven Whitehouse <swhiteho@redhat.com> Cc: Andrew Lutomirski <luto@kernel.org> Cc: Andreas Gruenbacher <agruenba@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Nicholas Piggin authored
A page is not added to the swap cache without being swap backed, so PageSwapBacked mappings can use PG_owner_priv_1 for PageSwapCache. Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Acked-by: Hugh Dickins <hughd@google.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Bob Peterson <rpeterso@redhat.com> Cc: Steven Whitehouse <swhiteho@redhat.com> Cc: Andrew Lutomirski <luto@kernel.org> Cc: Andreas Gruenbacher <agruenba@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Thomas Gleixner authored
No point in going through loops and hoops instead of just comparing the values. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org>
-
Thomas Gleixner authored
ktime_set(S,N) was required for the timespec storage type and is still useful for situations where a Seconds and Nanoseconds part of a time value needs to be converted. For anything where the Seconds argument is 0, this is pointless and can be replaced with a simple assignment. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org>
-