IO-APIC support in the presence of interrupt-remapping infrastructure.

IO-APIC RTE will be programmed with interrupt-remapping table entry(IRTE)
index and the IRTE will contain information about the vector, cpu destination,
trigger mode etc, which traditionally was present in the IO-APIC RTE.

Introduce a new irq_chip for cleaner irq migration (in the process
context as opposed to the current irq migration in the context of an interrupt.
interrupt-remapping infrastructure will help us achieve this cleanly).

For edge triggered, irq migration is a simple atomic update(of vector
and cpu destination) of IRTE and flush the hardware cache.

For level triggered, we need to modify the io-apic RTE aswell with the update
vector information, along with modifying IRTE with vector and cpu destination.
So irq migration for level triggered is little  bit more complex compared to
edge triggered migration. But the good news is, we use the same algorithm
for level triggered migration as we have today, only difference being,
we now initiate the irq migration from process context instead of the
interrupt context.

In future, when we do a directed EOI (combined with cpu EOI broadcast
suppression) to the IO-APIC, level triggered irq migration will also be
as simple as edge triggered migration and we can do the irq migration
with a simple atomic update to IO-APIC RTE.

TBD: some tests/changes needed in the presence of fixup_irqs() for
level triggered irq migration.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x2apic cluster mode support.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Introduce self IPI op for genapic.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x2apic ops for x2apic mode support. This uses MSR interface and differs
slightly from the xapic register layout.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Interrupt-remapping enables queued invalidation. And once queued invalidation
is enabled, IOTLB invalidation also needs to use the queued invalidation
mechanism and the register based IOTLB invalidation doesn't work.

For now, Support for IOTLB invalidation using queued invalidation is
missing. Meanwhile, disable DMA-remapping, if Interrupt-remapping
support is detected.

For the meanwhile, if someone wants to really enable DMA-remapping, they
can use nox2apic, which will disable interrupt-remapping and as such
doesn't enable queued invalidation.

And given that none of the release platforms support intr-remapping yet,
we should be ok for this temporary hack.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

cpuid feature for x2apic.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Introduce basic apic operations which handle the apic programming. This
will be used later to introduce another specific operations for x2apic.

For the perfomance critial accesses like IPI's, EOI etc, we use the
native operations as they are already referenced by different
indirections like genapic, irq_chip etc.

64bit Paravirt ops can also define their apic operations accordingly.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Yinghai Lu wrote:

> Setting APIC routing to physical flat
> Kernel panic - not syncing: Boot APIC ID in local APIC unexpected (0 vs 4)
> Pid: 1, comm: swapper Not tainted 2.6.26-rc9-tip-01763-g74f94b1-dirty #320
>
> Call Trace:
>  [<ffffffff80a21505>] ? set_cpu_sibling_map+0x38c/0x3bd
>  [<ffffffff80245215>] ? read_xapic_id+0x25/0x3e
>  [<ffffffff80e5a2c3>] ? verify_local_APIC+0x139/0x1b9
>  [<ffffffff80245215>] ? read_xapic_id+0x25/0x3e
>  [<ffffffff80e589af>] ? native_smp_prepare_cpus+0x224/0x2e9
>  [<ffffffff80e4881a>] ? kernel_init+0x64/0x341
>  [<ffffffff8022a439>] ? child_rip+0xa/0x11
>  [<ffffffff80e487b6>] ? kernel_init+0x0/0x341
>  [<ffffffff8022a42f>] ? child_rip+0x0/0x11
>
>
> guess read_apic_id changing cuase some problem...

genapic's read_apic_id() returns the actual apic id extracted from
the APIC_ID register. And in some cases like UV, read_apic_id()
returns completely different values from APIC ID register.

Use the native apic register read, rather than genapic read_apic_id()
in verify_local_APIC()

And also, lapic_suspend() should also use native apic register read.
Reported-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "akpm@linux-foundation.org" <akpm@linux-foundation.org>
Cc: "arjan@linux.intel.com" <arjan@linux.intel.com>
Cc: "andi@firstfloor.org" <andi@firstfloor.org>
Cc: "ebiederm@xmission.com" <ebiederm@xmission.com>
Cc: "jbarnes@virtuousgeek.org" <jbarnes@virtuousgeek.org>
Cc: "steiner@sgi.com" <steiner@sgi.com>
Cc: "jeremy@goop.org" <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Move the read_apic_id()  to genapic routines.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Generic ioapic specific routines which be used later during enabling
interrupt-remapping.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

8259 specific mask/unmask routines which be used later while enabling
interrupt-remapping.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Generic infrastructure for migrating the irq from the process context in the
presence of CONFIG_GENERIC_PENDING_IRQ.

This will be used later for migrating irq in the presence of
interrupt-remapping.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Routines handling the management of interrupt remapping table entries.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Interrupt remapping (part of Intel Virtualization Tech for directed I/O)
infrastructure.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Queued invalidation (part of Intel Virtualization Technology for
Directed I/O architecture) infrastructure.

This will be used for invalidating the interrupt entry cache in the
case of Interrupt-remapping and IOTLB invalidation in the case
of DMA-remapping.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

move IOMMU_WAIT_OP() macro to header file.

This will be used by both DMA-remapping and Intr-remapping.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Parse the vt-d device scope structures to find the mapping between IO-APICs
and the interrupt remapping hardware units.

This will be used later for enabling Interrupt-remapping for IOAPIC devices.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Presence of RMRR structures is not compulsory for enabling DMA-remapping.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Yong Y Wang <yong.y.wang@intel.com>
Cc: Yong Y Wang <yong.y.wang@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

DMA remapping specific code covered with CONFIG_DMAR in
the generic code which will also be used later for enabling Interrupt-remapping.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Allocate the iommu during the parse of DMA remapping hardware
definition structures. And also, introduce routines for device
scope initialization which will be explicitly called during
dma-remapping initialization.

These will be used for enabling interrupt remapping separately from the
existing DMA-remapping enabling sequence.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Clean up the intel-iommu code related to deferred iommu flush logic. There is
no need to allocate all the iommu's as a sequential array.

This will be used later in the interrupt-remapping patch series to
allocate iommu much early and individually for each device remapping
hardware unit.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

code reorganization of the generic Intel vt-d parsing related routines and linux
iommu routines specific to Intel vt-d.

drivers/pci/dmar.c	now contains the generic vt-d parsing related routines
drivers/pci/intel_iommu.c contains the iommu routines specific to vt-d
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Conflicts:

	arch/x86/mm/ioremap.c
Signed-off-by: Ingo Molnar <mingo@elte.hu>

On three of the several paths in entry_64.S that call
do_notify_resume() on the way back to user mode, we fail to properly
check again for newly-arrived work that requires another call to
do_notify_resume() before going to user mode.  These paths set the
mask to check only _TIF_NEED_RESCHED, but this is wrong.  The other
paths that lead to do_notify_resume() do this correctly already, and
entry_32.S does it correctly in all cases.

All paths back to user mode have to check all the _TIF_WORK_MASK
flags at the last possible stage, with interrupts disabled.
Otherwise, we miss any flags (TIF_SIGPENDING for example) that were
set any time after we entered do_notify_resume().  More work flags
can be set (or left set) synchronously inside do_notify_resume(), as
TIF_SIGPENDING can be, or asynchronously by interrupts or other CPUs
(which then send an asynchronous interrupt).

There are many different scenarios that could hit this bug, most of
them races.  The simplest one to demonstrate does not require any
race: when one signal has done handler setup at the check before
returning from a syscall, and there is another signal pending that
should be handled.  The second signal's handler should interrupt the
first signal handler before it actually starts (so the interrupted PC
is still at the handler's entry point).  Instead, it runs away until
the next kernel entry (next syscall, tick, etc).

This test behaves correctly on 32-bit kernels, and fails on 64-bit
(either 32-bit or 64-bit test binary).  With this fix, it works.

    #define _GNU_SOURCE
    #include <stdio.h>
    #include <signal.h>
    #include <string.h>
    #include <sys/ucontext.h>

    #ifndef REG_RIP
    #define REG_RIP REG_EIP
    #endif

    static sig_atomic_t hit1, hit2;

    static void
    handler (int sig, siginfo_t *info, void *ctx)
    {
      ucontext_t *uc = ctx;

      if ((void *) uc->uc_mcontext.gregs[REG_RIP] == &handler)
        {
          if (sig == SIGUSR1)
            hit1 = 1;
          else
            hit2 = 1;
        }

      printf ("%s at %#lx\n", strsignal (sig),
              uc->uc_mcontext.gregs[REG_RIP]);
    }

    int
    main (void)
    {
      struct sigaction sa;
      sigset_t set;

      sigemptyset (&sa.sa_mask);
      sa.sa_flags = SA_SIGINFO;
      sa.sa_sigaction = &handler;

      if (sigaction (SIGUSR1, &sa, NULL)
          || sigaction (SIGUSR2, &sa, NULL))
        return 2;

      sigemptyset (&set);
      sigaddset (&set, SIGUSR1);
      sigaddset (&set, SIGUSR2);
      if (sigprocmask (SIG_BLOCK, &set, NULL))
        return 3;

      printf ("main at %p, handler at %p\n", &main, &handler);

      raise (SIGUSR1);
      raise (SIGUSR2);

      if (sigprocmask (SIG_UNBLOCK, &set, NULL))
        return 4;

      if (hit1 + hit2 == 1)
        {
          puts ("PASS");
          return 0;
        }

      puts ("FAIL");
      return 1;
    }
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

We have two conflicting DMA-based quirks in there for the same set of
boxes (HP nx6325 and nx6125) and one of them actually breaks my box.

So remove the extra code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: =?iso-8859-1?q?T=F6r=F6k_Edwin?= <edwintorok@gmail.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [PATCH] IPMI: return correct value from ipmi_write

This patch corrects the handling of write operations to the IPMI watchdog
to work as intended by returning the number of characters actually
processed. Without this patch, an "echo V >/dev/watchdog" enables the
watchdog if IPMI is providing the watchdog function.
Signed-off-by: Mark Rustad <MRustad@gmail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

In the course of the recent unification of the NMI watchdog an assignment
to timer_ack to switch off unnecesary POLL commands to the 8259A in the
case of a watchdog failure has been accidentally removed.  The statement
used to be limited to the 32-bit variation as since the rewrite of the
timer code it has been relevant for the 82489DX only.  This change brings
it back.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

There is no such entity as ISA IRQ2.  The ACPI spec does not make it
explicitly clear, but does not preclude it either -- all it says is ISA
legacy interrupts are identity mapped by default (subject to overrides),
but it does not state whether IRQ2 exists or not.  As a result if there is
no IRQ0 override, then IRQ2 is normally initialised as an ISA interrupt,
which implies an edge-triggered line, which is unmasked by default as this
is what we do for edge-triggered I/O APIC interrupts so as not to miss an
edge.

To the best of my knowledge it is useless, as IRQ2 has not been in use
since the PC/AT as back then it was taken by the 8259A cascade interrupt
to the slave, with the line position in the slot rerouted to newly-created
IRQ9.  No device could thus make use of this line with the pair of 8259A
chips.  Now in theory INTIN2 of the I/O APIC may be usable, but the
interrupt of the device wired to it would not be available in the PIC mode
at all, so I seriously doubt if anybody decided to reuse it for a regular
device.

However there are two common uses of INTIN2.  One is for IRQ0, with an
ACPI interrupt override (or its equivalent in the MP table).  But in this
case IRQ2 is gone entirely with INTIN0 left vacant.  The other one is for
an 8959A ExtINTA cascade.  In this case IRQ0 goes to INTIN0 and if ACPI is
used INTIN2 is assumed to be IRQ2 (there is no override and ACPI has no
way to report ExtINTA interrupts).  This is where a problem happens.

The problem is INTIN2 is configured as a native APIC interrupt, with a
vector assigned and the mask cleared.  And the line may indeed get active
and inject interrupts if the master 8959A has its timer interrupt enabled
(it might happen for other interrupts too, but they are normally masked in
the process of rerouting them to the I/O APIC).  There are two cases where
it will happen:

* When the I/O APIC NMI watchdog is enabled.  This is actually a misnomer
  as the watchdog pulses are delivered through the 8259A to the LINT0
  inputs of all the local APICs in the system.  The implication is the
  output of the master 8259A goes high and low repeatedly, signalling
  interrupts to INTIN2 which is enabled too!

  [The origin of the name is I think for a brief period during the
  development we had a capability in our code to configure the watchdog to
  use an I/O APIC input; that would be INTIN2 in this scenario.]

* When the native route of IRQ0 via INTIN0 fails for whatever reason -- as
  it happens with the system considered here.  In this scenario the timer
  pulse is delivered through the 8259A to LINT0 input of the local APIC of
  the bootstrap processor, quite similarly to how is done for the watchdog
  described above.  The result is, again, INTIN2 receives these pulses
  too.  Rafael's system used to escape this scenario, because an incorrect
  IRQ0 override would occupy INTIN2 and prevent it from being unmasked.

My conclusion is IRQ2 should be excluded from configuration in all the
cases and the current exception for ACPI systems should be lifted.  The
reason being the exception not only being useless, but harmful as well.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Unlike the 32-bit one, the 64-bit variation of the LVT0 setup code for
the "8259A Virtual Wire" through the local APIC timer configuration does
not fully configure the relevant irq_chip structure.  Instead it relies on
the preceding I/O APIC code to have set it up, which does not happen if
the I/O APIC variants have not been tried.

The patch includes corresponding changes to the 32-bit variation too
which make them both the same, barring a small syntactic difference
involving sequence of functions in the source.  That should work as an aid
with the upcoming merge.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

 IRQ0 is edge-triggered, but the "8259A Virtual Wire" through the local
APIC configuration in the 32-bit version uses the "fasteoi" handler
suitable for level-triggered APIC interrupt.  Rewrite code so that the
"edge" handler is used.  The 64-bit version uses different code and is
unaffected.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Merge dwarf2_32.h and dwarf2_64.h into dwarf2.h.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

In dwarf2_32.h, test for CONFIG_AS_CFI instead of
CONFIG_UNWIND_INFO. Turns out that searching for UNWIND_INFO
returns no match in any Kconfig or Makefile, so we're really
just throwing everything away regarding dwarf frames for i386.

The test that generates CONFIG_AS_CFI does not have anything
x86_64-specific, and right now, checking V=1 builds shows me
that the flags is there anyway, although unused.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

In dwarf_64.h header, use the "ignore" macro the way
i386 does.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

The RING0_INT_FRAME macro defines a CFI_STARTPROC.
So we should really be using CFI_ENDPROC after it.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata-acpi: don't call sleeping function from invalid context
  Added Targa Visionary 1000 IDE adapter to pata_sis.c
  libata-acpi: filter out DIPM enable

When we release the iclog, we do an atomic_dec_and_lock to determine if
we are the last reference and need to trigger update of log headers and
writeout.  However, in xlog_state_get_iclog_space() we also need to
check if we have the last reference count there.  If we do, we release
the log buffer, otherwise we decrement the reference count.

But the compare and decrement in xlog_state_get_iclog_space() is not
atomic, so both places can see a reference count of 2 and neither will
release the iclog.  That leads to a filesystem hang.

Close the race by replacing the atomic_read() and atomic_dec() pair with
atomic_add_unless() to ensure that they are executed atomically.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Tim Shimmin <tes@sgi.com>
Tested-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>