If a device does not have a pnetid, users can set a temporary pnetid for
said device in the pnet table. This patch reworks the pnet table to make
it more flexible. Multiple entries with the same pnetid but differing
devices are now allowed. Additionally, the netlink interface now sends
each mapping from pnetid to device separately to the user while
maintaining the message format existing applications might expect. Also,
the SMC data structure for ib devices already has a pnetid attribute.
So, it is used to store the user defined pnetids. As a result, the pnet
table entries are only used for netdevs.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pnetids are retrieved from the underlying hardware as EBCDIC. This patch
converts pnetids to ASCII.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use local variable pflags from the beginning of function
smcr_tx_sndbuf_nonempty
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are rare cases where a PL_INT_CAUSE bit may end up getting
set when the corresponding PL_INT_ENABLE bit isn't set.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: disable aneg in genphy_c45_pma_setup_forced

When genphy_c45_pma_setup_forced() is called the "aneg enabled" bit
may still be set, therefore clear it. This is also in line with what
genphy_setup_forced() does for Clause 22.

v2:
- fix a typo in patch 1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that genphy_c45_pma_setup_forced() makes sure the "aneg enabled"
bit is cleared, the call to genphy_c45_an_disable_aneg() isn't needed
any longer. And the code pattern is now the same as in
genphy_config_aneg().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When genphy_c45_pma_setup_forced() is called the "aneg enabled" bit may
still be set, therefore clear it. This is also in line with what
genphy_setup_forced() does for Clause 22.

v2:
- fix typo
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2019-02-19

This series includes misc updates to mlx5 drivers and one ethtool update.

1) From Aya Levin:
   - ethtool: Define 50Gbps per lane link modes
   - add support for 50Gbps per lane link modes in mlx5 driver

2) From Tariq Toukan,
   - Add a helper function to unify mlx5 resource reloading

3) From Vlad Buslov,
   - Remove wrong and superfluous tc pedit header type check

4) From Tonghao Zhang,
   - Some refactoring in en_tc.c to simplify the mlx5e_tc_add_fdb_flow

5) From Leon Romanovsky & Saeed,
   - Compilation warning fixes

6) From Bodong wang,
   - E-Switch fixes that are related to the SmarNIC series
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

(cherry picked from commit 033b228e)

When tcindex_destroy() destroys all the filter results in
the perfect hash table, it invokes the walker to delete
each of them. However, results with class==0 are skipped
in either tcindex_walk() or tcindex_delete(), which causes
a memory leak reported by kmemleak.

This patch fixes it by skipping the walker and directly
deleting these filter results so we don't miss any filter
result.

As a result of this change, we have to initialize exts->net
properly in tcindex_alloc_perfect_hash(). For net-next, we
need to consider whether we should initialize ->net in
tcf_exts_init() instead, before that just directly test
CONFIG_NET_CLS_ACT=y.

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

(cherry picked from commit 8015d93e)

tcindex_destroy() invokes tcindex_destroy_element() via
a walker to delete each filter result in its perfect hash
table, and tcindex_destroy_element() calls tcindex_delete()
which schedules tcf RCU works to do the final deletion work.
Unfortunately this races with the RCU callback
__tcindex_destroy(), which could lead to use-after-free as
reported by Adrian.

Fix this by migrating this RCU callback to tcf RCU work too,
as that workqueue is ordered, we will not have use-after-free.

Note, we don't need to hold netns refcnt because we don't call
tcf_exts_destroy() here.

Fixes: 27ce4f05 ("net_sched: use tcf_queue_work() in tcindex filter")
Reported-by: Adrian <bugs@abtelecom.ro>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 121d57af ("gso: validate gso_type in GSO handlers") added
gso_type validation to existing gso_segment callback functions, to
filter out illegal and potentially dangerous SKB_GSO_DODGY packets.

Convert tunnels that now call inet_gso_segment and ipv6_gso_segment
directly to have their own callbacks and extend validation to these.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test case 'control_msg' has been updated to peek non-data record and
then verify the type of record received. Subsequently, the same record
is retrieved without MSG_PEEK flag in recvmsg().
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Two easily resolvable overlapping change conflicts, one in
TCP and one in the eBPF verifier.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Fix suspend and resume in mt76x0u USB driver, from Stanislaw
    Gruszka.

 2) Missing memory barriers in xsk, from Magnus Karlsson.

 3) rhashtable fixes in mac80211 from Herbert Xu.

 4) 32-bit MIPS eBPF JIT fixes from Paul Burton.

 5) Fix for_each_netdev_feature() on big endian, from Hauke Mehrtens.

 6) GSO validation fixes from Willem de Bruijn.

 7) Endianness fix for dwmac4 timestamp handling, from Alexandre Torgue.

 8) More strict checks in tcp_v4_err(), from Eric Dumazet.

 9) af_alg_release should NULL out the sk after the sock_put(), from Mao
    Wenan.

10) Missing unlock in mac80211 mesh error path, from Wei Yongjun.

11) Missing device put in hns driver, from Salil Mehta.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
  sky2: Increase D3 delay again
  vhost: correctly check the return value of translate_desc() in log_used()
  net: netcp: Fix ethss driver probe issue
  net: hns: Fixes the missing put_device in positive leg for roce reset
  net: stmmac: Fix a race in EEE enable callback
  qed: Fix iWARP syn packet mac address validation.
  qed: Fix iWARP buffer size provided for syn packet processing.
  r8152: Add support for MAC address pass through on RTL8153-BD
  mac80211: mesh: fix missing unlock on error in table_path_del()
  net/mlx4_en: fix spelling mistake: "quiting" -> "quitting"
  net: crypto set sk to NULL when af_alg_release.
  net: Do not allocate page fragments that are not skb aligned
  mm: Use fixed constant in page_frag_alloc instead of size + 1
  tcp: tcp_v4_err() should be more careful
  tcp: clear icsk_backoff in tcp_write_queue_purge()
  net: mv643xx_eth: disable clk on error path in mv643xx_eth_shared_probe()
  qmi_wwan: apply SET_DTR quirk to Sierra WP7607
  net: stmmac: handle endianness in dwmac4_get_timestamp
  doc: Mention MSG_ZEROCOPY implementation for UDP
  mlxsw: __mlxsw_sp_port_headroom_set(): Fix a use of local variable
  ...

Another platform requires even longer delay to make the device work
correctly after S3.

So increase the delay to 300ms.

BugLink: https://bugs.launchpad.net/bugs/1798921Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Passing the struct ptp_clock_info caps by parameter is passing over 130 bytes
of data by value on the stack. Optimize this by passing it by reference instead.
Also shinks the object code size:

Before:
   text	   data	    bss	    dec	    hex	filename
  12596	   2160	     64	  14820	   39e4	drivers/ptp/ptp_qoriq.o

After:
   text	   data	    bss	    dec	    hex	filename
  12567	   2160	     64	  14791	   39c7	drivers/ptp/ptp_qoriq.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When disabling vport, relevant vport configurations will be cleaned
up. These cleanups should be done to the vports which had these configs
applied at vport enablement. As esw manager vport didn't have such
vport config applied, cleanup should not touch it.

Fixes: de9e6a8136c5 ("net/mlx5: E-Switch, Properly refer to host PF vport as other vport")
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reported-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When eswitch gets vport data structure, the index should not be out
of the range of the vport array. Driver mistakenly used vport number
to check the range.

Fixes: 22b8ddc86bf4 ("net/mlx5: E-Switch, Assign a different position for uplink rep and vport")
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Fix the following compiler warning:

drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:2770:
warning: unused variable ‘esw’ [-Wunused-variable]

Fixes: 1cd3ab86b713 ("net/mlx5e: Introduce mlx5e_flow_esw_attr_init() helper")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

fpga_qpn was assigned but never used and compilation with W=1
produced the following warning:

drivers/net/ethernet/mellanox/mlx5/core/fpga/core.c: In function _mlx5_fpga_event_:
drivers/net/ethernet/mellanox/mlx5/core/fpga/core.c:320:6: warning:
variable _fpga_qpn_ set but not used [-Wunused-but-set-variable]
  u32 fpga_qpn;
      ^~~~~~~~

Fixes: 98db16ba ("net/mlx5: FPGA, Handle QP error event")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Compilation with W=1 produces following warning:

drivers/net/ethernet/mellanox/mlx5/core/en/monitor_stats.c:69:6:
warning: no previous prototype for _mlx5e_monitor_counter_start_ [-Wmissing-prototypes]
 void mlx5e_monitor_counter_start(struct mlx5e_priv *priv)
      ^~~~~~~~~~~~~~~~~~~~~~~~~~~

Avoid it by declaring mlx5e_monitor_counter_start() as a static function.

Fixes: 5c7e8bbb ("net/mlx5e: Use monitor counters for update stats")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

This patch is a little improvement. Simplify the mlx5e_tc_add_fdb_flow().
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Introduce the mlx5e_flow_esw_attr_init() helper
for simplifying codes.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

With recent introduction of flow_rule infrastructure drivers no longer
directly include action headers, so it is no longer possible to use
constants defined in them. Instead, one of flow_rule patches substituted
pedit action header constant with hardcoded value '2' in mlx5
set_pedit_val() function conditional which verifies that header type is in
range of values allowed by pedit action. That conditional is now both
wrong (hardcoded value is '2' but __PEDIT_HDR_TYPE_MAX is 6 in current
version) and superfluous (pedit action already verifies that header type is
in allowed range during init). Remove the described check from mlx5 code.

Fixes: 73867881 ("drivers: net: use flow action infrastructure")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Take into a function the common code structure of opening
a side set of channels followed by a call to apply them.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

In previous patch, driver added new speed modes: 50Gbps per lane support
for 50G/100G/200G.  This patch modifies mlx5e_get_link_ksettings and
mlx5e_set_link_ksettings to set and get these link modes via ethtool.
In order to do so, added mapping of new HW bits to ethtool bitmap and
enforce mutual exclusion between extended link modes and previously
defined link modes.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Added support for 50Gbps per lane link modes. Define various 50G, 100G
and 200G link modes using it.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Merge branch 'ieee802154-for-davem-2019-02-19' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan-next

Stefan Schmidt says:

====================
pull-request: ieee802154-next 2019-02-19

An update from ieee802154 for *net-next*

Another quite quite cycle in the ieee802154 subsystem.
Peter did a rework of the IP frag queue handling to make it use rbtree and get
in line with the core IPv4 and IPv6 implementatiosn in the kernel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to do code cleanup for ns83820_probe_phy().
It deletes unused variable 'first', commented out code,
and the pointless 'for' loop.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

when capable check failed, dev_put should
be call before return -EACCES.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RGMII_ID specifies that we should have internal delay, so resurrect the
delay addition routine but under the RGMII_ID mode.

Fixes: 40269aa9f40a ("net: dsa: qca8k: disable delay for RGMII mode")
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

When fail, translate_desc() returns negative value, otherwise the
number of iovs. So we should fail when the return value is negative
instead of a blindly check against zero.

Detected by CoverityScan, CID# 1442593:  Control flow issues  (DEADCODE)

Fixes: cc5e7107 ("vhost: log dirty page correctly")
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Update for net-next.

This series includes the usual firmware spec. update, a PCI ID addition,
enhancements for VF trust, MDIO read/write for external PHY, and
fixing the return code when TC flow offload fails.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver returns -ENOSPC when tc_can_offload() check fails. Since that
routine checks for flow parameters that are not supported by the driver,
we should return the more appropriate -EOPNOTSUPP.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for SIOCGMIIREG and SIOCSMIIREG ioctls to
mdio read/write to external PHY.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Newer firmware understands the concept of a trusted VF, so propagate the
trusted VF attribute set by the PF admin. to the firmware.  Also, check
the firmware trusted setting when considering the VF MAC address change
and reporting the trusted setting to the user.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for BCM957504 with device ID 1751
Signed-off-by: Erik Burrows <erik.burrows@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Firmware error recover is the major change in this spec.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Each tls context maintains two cipher contexts (one each for tx and rx
directions). For each tls session, the constants such as protocol
version, ciphersuite, iv size, associated data size etc are same for
both the directions and need to be stored only once per tls context.
Hence these are moved from 'struct cipher_context' to 'struct
tls_prot_info' and stored only once in 'struct tls_context'.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch aligns IP defragmenation logic in 6lowpan with that
of IPv4 and IPv6: see
commit d4289fcc ("net: IP6 defrag: use rbtrees for IPv6 defrag")

Modifying ip_defrag selftest seemed like an overkill, as I suspect
most kernel test setups do not have 6lowpan hwsim enabled. So I ran
the following code/script manually:

	insmod ./mac802154_hwsim.ko

	iwpan dev wpan0 set pan_id 0xbeef
	ip link add link wpan0 name lowpan0 type lowpan
	ip link set wpan0 up
	ip link set lowpan0 up

	iwpan dev wpan1 set pan_id 0xbeef
	ip netns add foo
	iwpan phy1 set netns name foo
	ip netns exec foo ip link add link wpan1 name lowpan1 type lowpan
	ip netns exec foo ip link set wpan1 up
	ip netns exec foo ip link set lowpan1 up

	ip -6 addr add "fb01::1/128" nodad dev lowpan0
	ip -netns foo -6 addr add "fb02::1/128" nodad dev lowpan1

	ip -6 route add "fb02::1/128" dev lowpan0
	ip -netns foo -6 route add "fb01::1/128" dev lowpan1

	# then in term1:
	   ip netns exec foo bash
	   ./udp_stream -6

	# in term2:
	    ./udp_stream -c -6 -H fb02::1

	# pr_warn_once showed that the code changed by this patch
	# was invoked.
Signed-off-by: Peter Oskolkov <posk@google.com>
Acked-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>