Introduce a helper to pass value and selector to. The helper packs them
into struct and puts them into netlink message.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net-next): ipsec-next 2020-03-28

1) Use kmem_cache_zalloc() instead of kmem_cache_alloc()
   in xfrm_state_alloc(). From Huang Zijiang.

2) esp_output_fill_trailer() is the same in IPv4 and IPv6,
   so share this function to avoide code duplcation.
   From Raed Salem.

3) Add offload support for esp beet mode.
   From Xin Long.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no point in preparing the module name in a buffer. The format
string can be passed diectly to 'request_module()'.

This axes a few lines of code and cleans a few things:
   - max len for a driver name is MODULE_NAME_LEN wich is ~ 60 chars,
     not 128. It would be down-sized in 'request_module()'
   - we should pass the total size of the buffer to 'snprintf()', not the
     size minus 1
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix sparse warnings:

drivers/net/ethernet/amazon/ena/ena_netdev.c:460:6: warning: symbol 'ena_xdp_exchange_program_rx_in_range' was not declared. Should it be static?
drivers/net/ethernet/amazon/ena/ena_netdev.c:481:6: warning: symbol 'ena_xdp_exchange_program' was not declared. Should it be static?
drivers/net/ethernet/amazon/ena/ena_netdev.c:1555:5: warning: symbol 'ena_xdp_handle_buff' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix sparse warning:

drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:2065:5:
 warning: symbol 'dpaa_a050385_wa' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a possibility that cdev is removed before CPL_ABORT_REQ_RSS
is fully processed, so it's better to save it in skb.

Added checks in handling the flow correctly, which suggests connection reset
request is sent to HW, wait for HW to respond.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPv6 header's payload length field shouldn't include IPv6 header length.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for VLAN ID-based filtering by the MAC controller for MAC
drivers that support it. Only the 12-bit VID field is used.
Signed-off-by: Chuah Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ayush Sawal says:

====================
crypto: chelsio: Fixes issues during chcr driver registration

Patch 1: Avoid the accessing of wrong u_ctx pointer.
Patch 2: Fixes a deadlock between rtnl_lock and uld_mutex.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The locks are taken in this order during driver registration
(uld_mutex), at: cxgb4_register_uld.part.14+0x49/0xd60 [cxgb4]
(rtnl_mutex), at: rtnetlink_rcv_msg+0x2db/0x400
(uld_mutex), at: cxgb_up+0x3a/0x7b0 [cxgb4]
(rtnl_mutex), at: chcr_add_xfrmops+0x83/0xa0 [chcr](stucked here)

To avoid this now the netdev features are updated after the
cxgb4_register_uld function is completed.

Fixes: 6dad4e8a ("chcr: Add support for Inline IPSec").
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This issue occurs only when multiadapters are present. Hang
happens because assign_chcr_device returns u_ctx pointer of
adapter which is not yet initialized as for this adapter cxgb_up
is not been called yet.

The last_dev pointer is used to determine u_ctx pointer and it
is initialized two times in chcr_uld_add in chcr_dev_add respectively.

The fix here is don't initialize the last_dev pointer during
chcr_uld_add. Only assign to value to it when the adapter's
initialization is completed i.e in chcr_dev_add.

Fixes: fef4912b ("crypto: chelsio - Handle PCI shutdown event").
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

'pm_nl_ctl' was adding a trailing whitespace after having printed the
IP. But at the end, the IP element is currently always the last one.

The bash script launching 'pm_nl_ctl' had trailing whitespaces in the
expected result on purpose. But these whitespaces have been removed when
the patch has been applied upstream. To avoid trailing whitespaces in
the bash code, 'pm_nl_ctl' and expected results have now been adapted.

The MPTCP PM selftest can now pass again.

Fixes: eedbc685 (selftests: add PM netlink functional tests)
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a spelling mistake in a dev_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2020-03-29

1) mlx5 core level updates for mkey APIs + migrate some code to mlx5_ib

2) Use a separate work queue for fib event handling

3) Move new eswitch chains files to a new directory, to prepare for
upcoming E-Switch and offloads features.

4) Support indr block setup (TC_SETUP_FT) in Flow Table mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add mlx5e_rep_indr_setup_ft_cb to support indr block setup
in FT mode.
Both tc rules and flow table rules are of the same format,
It can re-use tc parsing for that, and move the flow table rules
to their steering domain(the specific chain_index), the indr
block offload in FT also follow this scenario.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Refactor indr setup block for support ft indr setup in the
next patch. The function mlx5e_rep_indr_offload exposes
'flags' in order set additional flag for FT in next patch.
Rename mlx5e_rep_indr_setup_tc_block to mlx5e_rep_indr_setup_block
and add flow_setup_cb_t callback parameters in order set the
specific callback for FT in next patch.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

eswitch_offloads_chains.{c,h} were just introduced this kernel release
cycle, eswitch is in high development demand right now and many
features are planned to be added to it. eswitch deserves its own
directory and here we move these new files to there, in preparation for
upcoming eswitch features and new files.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>

In VF lag mode when remove the bonding module without bring down the
bond device first, we could potentially have circular dependency when we
unload IB devices and also handle fib events:
1. The bond work starts first;
2. The "modprobe -rv bonding" process tries to release the bond device,
   with the "pernet_ops_rwsem" lock hold;
3. The bond work blocks in unregister_netdevice_notifier() and waits for
the lock because fib event came right before;
4. The kernel fib module tries to free all the fib entries by broadcasting
   the "FIB_EVENT_NH_DEL" event;
5. Upon the fib event this lag_mp module holds the fib lock and queue a
   fib work.
So:
   bond work -> modprobe task -> kernel fib module -> lag_mp -> bond work

Today we either reload IB devices in roce lag in nic mode or either handle
fib events in switchdev mode, but a new feature could change that we'll
need to reload IB devices also in switchdev mode so this is a future proof
fix as one may not notice this later.
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
  mlx5: Remove uninitialized use of key in mlx5_core_create_mkey
  {IB,net}/mlx5: Move asynchronous mkey creation to mlx5_ib
  {IB,net}/mlx5: Assign mkey variant in mlx5_ib only
  {IB,net}/mlx5: Setup mkey variant before mr create command invocation
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Michal Kubecek says:

====================
ethtool netlink interface, part 4

Implementation of more netlink request types:

  - coalescing (ethtool -c/-C, patches 2-4)
  - pause parameters (ethtool -a/-A, patches 5-7)
  - EEE settings (--show-eee / --set-eee, patches 8-10)
  - timestamping info (-T, patches 11-12)

Patch 1 is a fix for netdev reference leak similar to commit 2f599ec4
("ethtool: fix reference leak in some *_SET handlers") but fixing a code

Changes in v3
  - change "one-step-*" Tx type names to "onestep-*", (patch 11, suggested
    by Richard Cochran
  - use "TSINFO" rather than "TIMESTAMP" for timestamping information
    constants and adjust symbol names (patch 12, suggested by Richard
    Cochran)

Changes in v2:
  - fix compiler warning in net_hwtstamp_validate() (patch 11)
  - fix follow-up lines alignment (whitespace only, patches 3 and 8)
which is only in net-next tree at the moment.
====================
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement TSINFO_GET request to get timestamping information for a network
device. This is traditionally available via ETHTOOL_GET_TS_INFO ioctl
request.

Move part of ethtool_get_ts_info() into common.c so that ioctl and netlink
code use the same logic to get timestamping information from the device.

v3: use "TSINFO" rather than "TIMESTAMP", suggested by Richard Cochran
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add three string sets related to timestamping information:

  ETH_SS_SOF_TIMESTAMPING: SOF_TIMESTAMPING_* flags
  ETH_SS_TS_TX_TYPES:      timestamping Tx types
  ETH_SS_TS_RX_FILTERS:    timestamping Rx filters

These will be used for TIMESTAMP_GET request.

v2: avoid compiler warning ("enumeration value not handled in switch")
    in net_hwtstamp_validate()

v3: omit dash in Tx type names ("one-step-*" -> "onestep-*"), suggested by
    Richard Cochran
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Send ETHTOOL_MSG_EEE_NTF notification whenever EEE settings of a network
device are modified using ETHTOOL_MSG_EEE_SET netlink message or
ETHTOOL_SEEE ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement EEE_SET netlink request to set EEE settings of a network device.
These are traditionally set with ETHTOOL_SEEE ioctl request.

The netlink interface allows setting the EEE status for all link modes
supported by kernel but only first 32 link modes can be set at the moment
as only those are supported by the ethtool_ops callback.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement EEE_GET request to get EEE settings of a network device. These
are traditionally available via ETHTOOL_GEEE ioctl request.

The netlink interface allows reporting EEE status for all link modes
supported by kernel but only first 32 link modes are provided at the moment
as only those are reported by the ethtool_ops callback and drivers.

v2: fix alignment (whitespace only)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Send ETHTOOL_MSG_PAUSE_NTF notification whenever pause parameters of
a network device are modified using ETHTOOL_MSG_PAUSE_SET netlink message
or ETHTOOL_SPAUSEPARAM ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement PAUSE_SET netlink request to set pause parameters of a network
device. Thease are traditionally set with ETHTOOL_SPAUSEPARAM ioctl
request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement PAUSE_GET request to get pause parameters of a network device.
These are traditionally available via ETHTOOL_GPAUSEPARAM ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Send ETHTOOL_MSG_COALESCE_NTF notification whenever coalescing parameters
of a network device are modified using ETHTOOL_MSG_COALESCE_SET netlink
message or ETHTOOL_SCOALESCE ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement COALESCE_SET netlink request to set coalescing parameters of
a network device. These are traditionally set with ETHTOOL_SCOALESCE ioctl
request. This commit adds only support for device coalescing parameters,
not per queue coalescing parameters.

Like the ioctl implementation, the generic ethtool code checks if only
supported parameters are modified; if not, first offending attribute is
reported using extack.

v2: fix alignment (whitespace only)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement COALESCE_GET request to get coalescing parameters of a network
device. These are traditionally available via ETHTOOL_GCOALESCE ioctl
request. This commit adds only support for device coalescing parameters,
not per queue coalescing parameters.

Omit attributes with zero values unless they are declared as supported
(i.e. the corresponding bit in ethtool_ops::supported_coalesce_params is
set).
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew noticed that some handlers for *_SET commands leak a netdev
reference if required ethtool_ops callbacks do not exist. One of them is
ethnl_set_privflags(), a simple reproducer would be e.g.

  ip link add veth1 type veth peer name veth2
  ethtool --set-priv-flags veth1 foo on
  ip link del veth1

Make sure dev_put() is called when ethtool_ops check fails.

Fixes: f265d799 ("ethtool: set device private flags with PRIVFLAGS_SET request")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexander Aring says:

====================
net: ipv6: add rpl source routing

This patch series will add handling for RPL source routing handling
and insertion (implement as lwtunnel)! I did an example prototype
implementation in rpld for using this implementation in non-storing mode:

https://github.com/linux-wpan/rpld/tree/nonstoring_mode

I will also present a talk at netdev about it:

https://netdevconf.info/0x14/session.html?talk-extend-segment-routing-for-RPL

In receive handling I add handling for IPIP encapsulation as RFC6554
describes it as possible. For reasons I didn't implemented it yet for
generating such packets because I am not really sure how/when this
should happen. So far I understand there exists a draft yet which
describes the cases (inclusive a Hop-by-Hop option which we also not
support yet).

https://tools.ietf.org/html/draft-ietf-roll-useofrplinfo-35

This is just the beginning to start implementation everything for yet,
step by step. It works for my use cases yet to have it running on a
6LOWPAN _only_ network.

I have some patches for iproute2 as well.

A sidenote: I check on local addresses if they are part of segment
routes, this is just to avoid stupid settings. A use can add addresses
afterwards what I cannot control anymore but then it's users fault to
make such thing. The receive handling checks for this as well which is
required by RFC6554, so the next hops or when it comes back should drop
it anyway.

To make this possible I added functionality to pass the net structure to
the build_state of lwtunnel (I hope I caught all lwtunnels).

Another sidenote: I set the headroom value to 0 as I figured out it will
break on interfaces with IPv6 min mtu if set to non zero for tunnels on
L3.

- Alex

changes since v3:
 - use parse_nested which isn't deprecated - Thanks David Ahern
 - change to return -1 instead errno in exthdr handling to unify
   error code
 - change function name from ipv6_rpl_srh_decompress_size to
   ipv6_rpl_srh_size

changes since v2:
 - add additional segdata length in lwtunnel build_state
 - fix build_state patch by not catching one inline noop function
   if LWTUNNEL is disabled

Alexander Aring (5):
  include: uapi: linux: add rpl sr header definition
  addrconf: add functionality to check on rpl requirements
  net: ipv6: add support for rpl sr exthdr
  net: add net available in build_state
  net: ipv6: add rpl sr tunnel
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds functionality to configure routes for RPL source routing
functionality. There is no IPIP functionality yet implemented which can
be added later when the cases when to use IPv6 encapuslation comes more
clear.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The build_state callback of lwtunnel doesn't contain the net namespace
structure yet. This patch will add it so we can check on specific
address configuration at creation time of rpl source routes.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds rpl source routing receive handling. Everything works
only if sysconf "rpl_seg_enabled" and source routing is enabled. Mostly
the same behaviour as IPv6 segmentation routing. To handle compression
and uncompression a rpl.c file is created which contains the necessary
functionality. The receive handling will also care about IPv6
encapsulated so far it's specified as possible nexthdr in RFC 6554.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a functionality to addrconf to check on a specific RPL
address configuration. According to RFC 6554:

To detect loops in the SRH, a router MUST determine if the SRH
includes multiple addresses assigned to any interface on that
router. If such addresses appear more than once and are separated by
at least one address not assigned to that router.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a uapi header for rpl struct definition. The segments
data can be accessed over rpl_segaddr or rpl_segdata macros. In case of
compri and compre is zero the segment data is not compressed and can be
accessed by rpl_segaddr. In the other case the compressed data can be
accessed by rpl_segdata and interpreted as byte array.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mat Martineau says:

====================
Multipath TCP part 3: Multiple subflows and path management

v2 -> v3: Remove 'inline' in .c files, fix uapi bit macros, and rebase.

v1 -> v2: Rebase on current net-next, fix for netlink limit setting,
and update .gitignore for selftest.

This patch set allows more than one TCP subflow to be established and
used for a multipath TCP connection. Subflows are added to an existing
connection using the MP_JOIN option during the 3-way handshake. With
multiple TCP subflows available, sent data is now stored in the MPTCP
socket so it may be retransmitted on any TCP subflow if there is no
DATA_ACK before a timeout. If an MPTCP-level timeout occurs, data is
retransmitted using an available subflow. Storing this sent data
requires the addition of memory accounting at the MPTCP level, which was
previously delegated to the single subflow. Incoming DATA_ACKs now free
data from the MPTCP-level retransmit buffer.

IP addresses available for new subflow connections can now be advertised
and received with the ADD_ADDR option, and the corresponding REMOVE_ADDR
option likewise advertises that an address is no longer available.

The MPTCP path manager netlink interface has commands to set in-kernel
limits for the number of concurrent subflows and control the
advertisement of IP addresses between peers.

To track and debug MPTCP connections there are new MPTCP MIB counters,
and subflow context can be requested using inet_diag. The MPTCP
self-tests now validate multiple-subflow operation and the netlink path
manager interface.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the pm netlink to configure the creation of several
subflows, and verify that via MIB counters.

Update the mptcp_connect program to allow reliable MP_JOIN
handshake even on small data file
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>