For this to work correctly on little-endian hosts, don't access the
device-tree properties directly in native endianness, but use the
of_property_read_u32() helper.
Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

The Soft UART hack is only needed for some PPC-based SOCs. To allow
building this driver for non-PPC, guard soft_uart_init() and its
helpers by CONFIG_PPC32, and use a no-op soft_uart_init() otherwise.
Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

The "soft uart" mechanism is a workaround for a silicon bug which (as
far as I know) only affects some PPC-based SOCs.

The code that determines which microcode blob to request relies on
some powerpc-specific bits (e.g. the mfspr(SPRN_SVR) and hence also
the asm/reg.h header). This makes it a little awkward to allow this
driver to be built for non-PPC based SOCs with a QE, even if they are
not affected by that silicon bug and thus don't need any of the Soft
UART logic.

There's no way around guarding those bits with some ifdeffery, so to
keep that isolated, factor out the
do-we-need-soft-uart-and-if-so-handle-the-firmware to a separate
function, which we can then easily stub out for non-PPC.
Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

Some ARM-based SOCs (e.g. LS1021A) also have a QUICC engine. As
preparation for allowing this driver to build on ARM, replace the
ppc-specific in_be16() etc. by the qe_io* helpers. Done via
coccinelle.
Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

This driver uses #defines from soc/fsl/cpm.h, so instead of relying on
some other header pulling that in, do that explicitly. This is
preparation for allowing this driver to build on ARM.
Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

asm/cpm.h under arch/powerpc is now just a wrapper for including
soc/fsl/cpm.h. In order to make the qe.h header usable on other
architectures, use the latter path directly.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

Some drivers, e.g. ucc_uart, need definitions from cpm.h. In order to
allow building those drivers for non-ppc based SOCs, move the header
to include/soc/fsl. For now, leave a trivial wrapper at the old
location so drivers can be updated one by one.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

This is necessary for this to work on little-endian hosts.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

We need to apply be32_to_cpu to make this work correctly on
little-endian hosts.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

Instead of manually doing of_get_property/of_find_property and reading
the value by assigning to a u32* or u64* and dereferencing, use the
of_property_read_* functions.

This make the code more readable, and more importantly, is required
for this to work correctly on little-endian platforms.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

The public qe_ic.h header is no longer included by anything but
qe_ic.c. Merge both headers into qe_ic.c, and drop the unused
constants.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

qe_ic_init() takes a flags parameter, but all callers (including the
sole remaining one) have always passed 0. So remove that parameter and
simplify the body accordingly. We still explicitly initialize the
Interrupt Configuration Register (CICR) to its reset value of
all-zeroes, just in case the bootloader has played funny games.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

These are only called from within qe_ic.c, so make them static.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

This driver is currently PPC-only, and on powerpc, NO_IRQ is 0, so
this doesn't change functionality. However, not every architecture
defines NO_IRQ, and some define it as -1, so the detection of a failed
irq_of_parse_and_map() (which returns 0 on failure) would be wrong on
those. So to prepare for allowing this driver to build on other
architectures, drop all references to NO_IRQ.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

There are no current callers of these functions, and they use the
ppc-specific virq_to_hw(). So removing them gets us one step closer to
building QE support for ARM.

If the functionality is ever actually needed, the code can be dug out
of git and then adapted to work on all architectures, but for future
reference please note that I believe qe_ic_set_priority is buggy: The
"priority < 4" should be "priority <= 4", and in the else branch 24
should be replaced by 28, at least if I'm reading the data sheet right.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

The qe_ic_cascade_{low,high}_mpic functions are now used as handlers
both when the interrupt parent is mpic as well as ipic, so remove the
_mpic suffix.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

These functions are only ever called through a function pointer, and
therefore it makes no sense for them to be "static inline" - gcc has
no choice but to emit a copy in each translation unit that takes the
address of one of these. Since they are now only referenced from
qe_ic.c, just make them local to that file.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

This is now exactly the same as mpc83xx_ipic_init_IRQ, so just use
that directly.
Acked-by: Scott Wood <oss@buserror.net>
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

Having to call qe_ic_init() from platform-specific code makes it
awkward to allow building the QE drivers for ARM. It's also a needless
duplication of code, and slightly error-prone: Instead of the caller
needing to know the details of whether the QUICC Engine High and QUICC
Engine Low are actually the same interrupt (see e.g. the machine_is()
in mpc85xx_mds_qeic_init), just let the init function choose the
appropriate handlers after it has parsed the DT and figured it out. If
the two interrupts are distinct, use separate handlers, otherwise use
the handler which first checks the CHIVEC register (for the high
priority interrupts), then the CIVEC.

All existing callers pass 0 for flags, so continue to do that from the
new single caller. Later cleanups will remove that argument
from qe_ic_init and simplify the body, as well as make qe_ic_init into
a proper init function for an IRQCHIP_DECLARE, eliminating the need to
manually look up the fsl,qe-ic node.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

The *_ipic and *_mpic handlers are almost identical - the only
difference is that the latter end with an unconditional
chip->irq_eoi() call. Since IPIC does not have ->irq_eoi, we can
reduce some code duplication by calling irq_eoi conditionally.

This is similar to what is already done in mpc8xxx_gpio_irq_cascade().

This leaves the functions slightly misnamed, but that will be fixed in
a subsequent patch.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

There's no point in registering with sysfs when that doesn't actually
allow any interaction with the device or driver (no uevents, no sysfs
files that provide information or allow configuration, no nothing).
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

high_active is only assigned to but never used. Remove it.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

These includes are not actually needed, and asm/rheap.h and
sysdev/fsl_soc.h are PPC-specific, hence prevent compiling QE for
other architectures.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

Commit e5c5c8d2 (soc/fsl/qe: only apply QE_General4 workaround on
affected SoCs) introduced use of pvr_version_is(), saying

    The QE_General4 workaround is only valid for the MPC832x and MPC836x
    SoCs. The other SoCs that embed a QUICC engine are not affected by this
    hardware bug and thus can use the computed divisors (this was
    successfully tested on the T1040).

I'm reading the above as saying that the errata does not apply to the
ARM-based SOCs with QUICC engine. In any case, use of pvr_version_is()
must be guarded by CONFIG_PPC32 before we can remove the PPC32
dependency from CONFIG_QUICC_ENGINE, so introduce qe_general4_errata()
to keep the necessary #ifdeffery localized to a trivial helper.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

In preparation for allowing QE to be built for architectures other
than ppc, use the generic readx_poll_timeout_atomic() helper from
iopoll.h rather than the ppc-only spin_event_timeout().
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

In preparation for allowing to build QE support for architectures
other than PPC, replace the ppc-specific io accessors by the qe_io*
macros. Done via

$ spatch --sp-file io.cocci --in-place drivers/soc/fsl/qe/

where io.cocci is

@@
expression addr, val;
@@
- out_be32(addr, val)
+ qe_iowrite32be(val, addr)

@@
expression addr;
@@
- in_be32(addr)
+ qe_ioread32be(addr)

@@
expression addr, val;
@@
- out_be16(addr, val)
+ qe_iowrite16be(val, addr)

@@
expression addr;
@@
- in_be16(addr)
+ qe_ioread16be(addr)

@@
expression addr, val;
@@
- out_8(addr, val)
+ qe_iowrite8(val, addr)

@@
expression addr;
@@
- in_8(addr)
+ qe_ioread8(addr)

@@
expression addr, clr, set;
@@
- clrsetbits_be32(addr, clr, set)
+ qe_clrsetbits_be32(addr, clr, set)

@@
expression addr, clr, set;
@@
- clrsetbits_be16(addr, clr, set)
+ qe_clrsetbits_be16(addr, clr, set)

@@
expression addr, clr, set;
@@
- clrsetbits_8(addr, clr, set)
+ qe_clrsetbits_8(addr, clr, set)

@@
expression addr, set;
@@
- setbits32(addr, set)
+ qe_setbits_be32(addr, set)

@@
expression addr, set;
@@
- setbits16(addr, set)
+ qe_setbits_be16(addr, set)

@@
expression addr, set;
@@
- setbits8(addr, set)
+ qe_setbits_8(addr, set)

@@
expression addr, clr;
@@
- clrbits32(addr, clr)
+ qe_clrbits_be32(addr, clr)

@@
expression addr, clr;
@@
- clrbits16(addr, clr)
+ qe_clrbits_be16(addr, clr)

@@
expression addr, clr;
@@
- clrbits8(addr, clr)
+ qe_clrbits_8(addr, clr)
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

The QUICC engine drivers use the powerpc-specific out_be32() etc. In
order to allow those drivers to build for other architectures, those
must be replaced by iowrite32be(). However, on powerpc, out_be32() is
a simple inline function while iowrite32be() is out-of-line. So in
order not to introduce a performance regression on powerpc when making
the drivers work on other architectures, introduce qe_io* helpers.

Also define the qe_{clr,set,clrset}bits* helpers in terms of these new
macros.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

Make it clear that these operate on big-endian registers (i.e. use the
iowrite*be primitives) before we introduce more uses of them and allow
the QE drivers to be built for platforms other than ppc32.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

The actual io accessors (e.g. in_be32) implicitly add a volatile
qualifier to their address argument. Remove volatile from the struct
definition and the qe_ic_(read/write) helpers, in preparation for
switching from the ppc-specific io accessors to generic ones.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>

Pull networking fixes from David Miller:

 1) More jumbo frame fixes in r8169, from Heiner Kallweit.

 2) Fix bpf build in minimal configuration, from Alexei Starovoitov.

 3) Use after free in slcan driver, from Jouni Hogander.

 4) Flower classifier port ranges don't work properly in the HW offload
    case, from Yoshiki Komachi.

 5) Use after free in hns3_nic_maybe_stop_tx(), from Yunsheng Lin.

 6) Out of bounds access in mqprio_dump(), from Vladyslav Tarasiuk.

 7) Fix flow dissection in dsa TX path, from Alexander Lobakin.

 8) Stale syncookie timestampe fixes from Guillaume Nault.

[ Did an evil merge to silence a warning introduced by this pull - Linus ]

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
  r8169: fix rtl_hw_jumbo_disable for RTL8168evl
  net_sched: validate TCA_KIND attribute in tc_chain_tmplt_add()
  r8169: add missing RX enabling for WoL on RTL8125
  vhost/vsock: accept only packets with the right dst_cid
  net: phy: dp83867: fix hfs boot in rgmii mode
  net: ethernet: ti: cpsw: fix extra rx interrupt
  inet: protect against too small mtu values.
  gre: refetch erspan header from skb->data after pskb_may_pull()
  pppoe: remove redundant BUG_ON() check in pppoe_pernet
  tcp: Protect accesses to .ts_recent_stamp with {READ,WRITE}_ONCE()
  tcp: tighten acceptance of ACKs not matching a child socket
  tcp: fix rejected syncookies due to stale timestamps
  lpc_eth: kernel BUG on remove
  tcp: md5: fix potential overestimation of TCP option space
  net: sched: allow indirect blocks to bind to clsact in TC
  net: core: rename indirect block ingress cb function
  net-sysfs: Call dev_hold always in netdev_queue_add_kobject
  net: dsa: fix flow dissection on Tx path
  net/tls: Fix return values to avoid ENOTSUPP
  net: avoid an indirect call in ____sys_recvmsg()
  ...

Pull more SCSI updates from James Bottomley:
 "Eleven patches, all in drivers (no core changes) that are either minor
  cleanups or small fixes.

  They were late arriving, but still safe for -rc1"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: MAINTAINERS: Add the linux-scsi mailing list to the ISCSI entry
  scsi: megaraid_sas: Make poll_aen_lock static
  scsi: sd_zbc: Improve report zones error printout
  scsi: qla2xxx: Fix qla2x00_request_irqs() for MSI
  scsi: qla2xxx: unregister ports after GPN_FT failure
  scsi: qla2xxx: fix rports not being mark as lost in sync fabric scan
  scsi: pm80xx: Remove unused include of linux/version.h
  scsi: pm80xx: fix logic to break out of loop when register value is 2 or 3
  scsi: scsi_transport_sas: Fix memory leak when removing devices
  scsi: lpfc: size cpu map by last cpu id set
  scsi: ibmvscsi_tgt: Remove unneeded variable rc

Pull cifs fixes from Steve French:
 "Nine cifs/smb3 fixes:

   - one fix for stable (oops during oplock break)

   - two timestamp fixes including important one for updating mtime at
     close to avoid stale metadata caching issue on dirty files (also
     improves perf by using SMB2_CLOSE_FLAG_POSTQUERY_ATTRIB over the
     wire)

   - two fixes for "modefromsid" mount option for file create (now
     allows mode bits to be set more atomically and accurately on create
     by adding "sd_context" on create when modefromsid specified on
     mount)

   - two fixes for multichannel found in testing this week against
     different servers

   - two small cleanup patches"

* tag '5.5-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: improve check for when we send the security descriptor context on create
  smb3: fix mode passed in on create for modetosid mount option
  cifs: fix possible uninitialized access and race on iface_list
  cifs: Fix lookup of SMB connections on multichannel
  smb3: query attributes on file close
  smb3: remove unused flag passed into close functions
  cifs: remove redundant assignment to pointer pneg_ctxt
  fs: cifs: Fix atime update check vs mtime
  CIFS: Fix NULL-pointer dereference in smb2_push_mandatory_locks

Pull misc vfs cleanups from Al Viro:
 "No common topic, just three cleanups".

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  make __d_alloc() static
  fs/namespace: add __user to open_tree and move_mount syscalls
  fs/fnctl: fix missing __user in fcntl_rw_hint()

Pull NTB update from Jon Mason:
 "Just a simple patch to add a new Hygon Device ID to the AMD NTB device
  driver"

* tag 'ntb-5.5' of git://github.com/jonmason/ntb:
  NTB: Add Hygon Device ID

Pull more input updates from Dmitry Torokhov:

 - fixups for Synaptics RMI4 driver

 - a quirk for Goodinx touchscreen on Teclast tablet

 - a new keycode definition for activating privacy screen feature found
   on a few "enterprise" laptops

 - updates to snvs_pwrkey driver

 - polling uinput device for writing (which is always allowed) now works

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers
  Input: synaptics-rmi4 - re-enable IRQs in f34v7_do_reflash
  Input: goodix - add upside-down quirk for Teclast X89 tablet
  Input: add privacy screen toggle keycode
  Input: uinput - fix returning EPOLLOUT from uinput_poll
  Input: snvs_pwrkey - remove gratuitous NULL initializers
  Input: snvs_pwrkey - send key events for i.MX6 S, DL and Q

Pull iomap fixes from Darrick Wong:
 "Fix a race condition and a use-after-free error:

   - Fix a UAF when reporting writeback errors

   - Fix a race condition when handling page uptodate on fragmented file
     with blocksize < pagesize"

* tag 'iomap-5.5-merge-14' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  iomap: stop using ioend after it's been freed in iomap_finish_ioend()
  iomap: fix sub-page uptodate handling

Pull xfs fixes from Darrick Wong:
 "Fix a couple of resource management errors and a hang:

   - fix a crash in the log setup code when log mounting fails

   - fix a hang when allocating space on the realtime device

   - fix a block leak when freeing space on the realtime device"

* tag 'xfs-5.5-merge-17' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: fix mount failure crash on invalid iclog memory access
  xfs: don't check for AG deadlock for realtime files in bunmapi
  xfs: fix realtime file data space leak