- 28 Jun, 2019 9 commits
-
-
Alexandru Ardelean authored
The arrays (of strings) that are passed to __sysfs_match_string() are static, so use sysfs_match_string() which does an implicit ARRAY_SIZE() over these arrays. Functionally, this doesn't change anything. The change is more cosmetic. It only shrinks the static arrays by 1 byte each. Signed-off-by:
Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by:
Coly Li <colyli@suse.de> Signed-off-by:
Jens Axboe <axboe@kernel.dk>
-
Coly Li authored
In function bset_search_tree(), when p >= t->size, t->tree[0] will be prefetched by the following code piece, 974 unsigned int p = n << 4; 975 976 p &= ((int) (p - t->size)) >> 31; 977 978 prefetch(&t->tree[p]); The purpose of the above code is to avoid a branch instruction, but when p >= t->size, prefetch(&t->tree[0]) has no positive performance contribution at all. This patch avoids the unncessary prefetch by only calling prefetch() when p < t->size. Signed-off-by:
-
Coly Li authored
When backing device super block is written by bch_write_bdev_super(), the bio complete callback write_bdev_super_endio() simply ignores I/O status. Indeed such write request also contribute to backing device health status if the request failed. This patch checkes bio->bi_status in write_bdev_super_endio(), if there is error, bch_count_backing_io_errors() will be called to count an I/O error to dc->io_errors. Signed-off-by:
-
Coly Li authored
When md raid device (e.g. raid456) is used as backing device, read-ahead requests on a degrading and recovering md raid device might be failured immediately by md raid code, but indeed this md raid array can still be read or write for normal I/O requests. Therefore such failed read-ahead request are not real hardware failure. Further more, after degrading and recovering accomplished, read-ahead requests will be handled by md raid array again. For such condition, I/O failures of read-ahead requests don't indicate real health status (because normal I/O still be served), they should not be counted into I/O error counter dc->io_errors. Since there is no simple way to detect whether the backing divice is a md raid device, this patch simply ignores I/O failures for read-ahead bios on backing device, to avoid bogus backing device failure on a degrading md raid array. Suggested-and-tested-by:
Thorsten Knabe <linux@thorsten-knabe.de> Signed-off-by:
-
Coly Li authored
When cache_set_flush() is called for too many I/O errors detected on cache device and the cache set is retiring, inside the function it doesn't make sense to flushing cached btree nodes from c->btree_cache because CACHE_SET_IO_DISABLE is set on c->flags already and all I/Os onto cache device will be rejected. This patch checks in cache_set_flush() that whether CACHE_SET_IO_DISABLE is set. If yes, then avoids to flush the cached btree nodes to reduce more time and make cache set retiring more faster. Signed-off-by:
-
Coly Li authored
This reverts commit 6147305c. Although this patch helps the failed bcache device to stop faster when too many I/O errors detected on corresponding cached device, setting CACHE_SET_IO_DISABLE bit to cache set c->flags was not a good idea. This operation will disable all I/Os on cache set, which means other attached bcache devices won't work neither. Without this patch, the failed bcache device can also be stopped eventually if internal I/O accomplished (e.g. writeback). Therefore here I revert it. Fixes: 6147305c ("bcache: set CACHE_SET_IO_DISABLE in bch_cached_dev_error()") Reported-by:
Yong Li <mr.liyong@qq.com> Signed-off-by:
-
Coly Li authored
When everything is OK in bch_journal_read(), finally the return value is returned by, return ret; which assumes ret will be 0 here. This assumption is wrong when all journal buckets as are full and filled with valid journal entries. In such cache the last location referencess read_bucket() sets 'ret' to 1, which means new jset added into jset list. The jset list is list 'journal' in caller run_cache_set(). Return 1 to run_cache_set() means something wrong and the cache set won't start, but indeed everything is OK. This patch changes the line at end of bch_journal_read() to directly return 0 since everything if verything is good. Then a bogus error is fixed. Signed-off-by:
-
Coly Li authored
When system memory is in heavy pressure, bch_gc_thread_start() from run_cache_set() may fail due to out of memory. In such condition, c->gc_thread is assigned to -ENOMEM, not NULL pointer. Then in following failure code path bch_cache_set_error(), when cache_set_flush() gets called, the code piece to stop c->gc_thread is broken, if (!IS_ERR_OR_NULL(c->gc_thread)) kthread_stop(c->gc_thread); And KASAN catches such NULL pointer deference problem, with the warning information: [ 561.207881] ================================================================== [ 561.207900] BUG: KASAN: null-ptr-deref in kthread_stop+0x3b/0x440 [ 561.207904] Write of size 4 at addr 000000000000001c by task kworker/15:1/313 [ 561.207913] CPU: 15 PID: 313 Comm: kworker/15:1 Tainted: G W 5.0.0-vanilla+ #3 [ 561.207916] Hardware name: Lenovo ThinkSystem SR650 -[7X05CTO1WW]-/-[7X05CTO1WW]-, BIOS -[IVE136T-2.10]- 03/22/2019 [ 561.207935] Workqueue: events cache_set_flush [bcache] [ 561.207940] Call Trace: [ 561.207948] dump_stack+0x9a/0xeb [ 561.207955] ? kthread_stop+0x3b/0x440 [ 561.207960] ? kthread_stop+0x3b/0x440 [ 561.207965] kasan_report+0x176/0x192 [ 561.207973] ? kthread_stop+0x3b/0x440 [ 561.207981] kthread_stop+0x3b/0x440 [ 561.207995] cache_set_flush+0xd4/0x6d0 [bcache] [ 561.208008] process_one_work+0x856/0x1620 [ 561.208015] ? find_held_lock+0x39/0x1d0 [ 561.208028] ? drain_workqueue+0x380/0x380 [ 561.208048] worker_thread+0x87/0xb80 [ 561.208058] ? __kthread_parkme+0xb6/0x180 [ 561.208067] ? process_one_work+0x1620/0x1620 [ 561.208072] kthread+0x326/0x3e0 [ 561.208079] ? kthread_create_worker_on_cpu+0xc0/0xc0 [ 561.208090] ret_from_fork+0x3a/0x50 [ 561.208110] ================================================================== [ 561.208113] Disabling lock debugging due to kernel taint [ 561.208115] irq event stamp: 11800231 [ 561.208126] hardirqs last enabled at (11800231): [<ffffffff83008538>] do_syscall_64+0x18/0x410 [ 561.208127] BUG: unable to handle kernel NULL pointer dereference at 000000000000001c [ 561.208129] #PF error: [WRITE] [ 561.312253] hardirqs last disabled at (11800230): [<ffffffff830052ff>] trace_hardirqs_off_thunk+0x1a/0x1c [ 561.312259] softirqs last enabled at (11799832): [<ffffffff850005c7>] __do_softirq+0x5c7/0x8c3 [ 561.405975] PGD 0 P4D 0 [ 561.442494] softirqs last disabled at (11799821): [<ffffffff831add2c>] irq_exit+0x1ac/0x1e0 [ 561.791359] Oops: 0002 [#1] SMP KASAN NOPTI [ 561.791362] CPU: 15 PID: 313 Comm: kworker/15:1 Tainted: G B W 5.0.0-vanilla+ #3 [ 561.791363] Hardware name: Lenovo ThinkSystem SR650 -[7X05CTO1WW]-/-[7X05CTO1WW]-, BIOS -[IVE136T-2.10]- 03/22/2019 [ 561.791371] Workqueue: events cache_set_flush [bcache] [ 561.791374] RIP: 0010:kthread_stop+0x3b/0x440 [ 561.791376] Code: 00 00 65 8b 05 26 d5 e0 7c 89 c0 48 0f a3 05 ec aa df 02 0f 82 dc 02 00 00 4c 8d 63 20 be 04 00 00 00 4c 89 e7 e8 65 c5 53 00 <f0> ff 43 20 48 8d 7b 24 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 [ 561.791377] RSP: 0018:ffff88872fc8fd10 EFLAGS: 00010286 [ 561.838895] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 561.838916] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 561.838934] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 561.838948] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 561.838966] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 561.838979] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 561.838996] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 563.067028] RAX: 0000000000000000 RBX: fffffffffffffffc RCX: ffffffff832dd314 [ 563.067030] RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000297 [ 563.067032] RBP: ffff88872fc8fe88 R08: fffffbfff0b8213d R09: fffffbfff0b8213d [ 563.067034] R10: 0000000000000001 R11: fffffbfff0b8213c R12: 000000000000001c [ 563.408618] R13: ffff88dc61cc0f68 R14: ffff888102b94900 R15: ffff88dc61cc0f68 [ 563.408620] FS: 0000000000000000(0000) GS:ffff888f7dc00000(0000) knlGS:0000000000000000 [ 563.408622] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 563.408623] CR2: 000000000000001c CR3: 0000000f48a1a004 CR4: 00000000007606e0 [ 563.408625] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 563.408627] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 563.904795] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 563.915796] PKRU: 55555554 [ 563.915797] Call Trace: [ 563.915807] cache_set_flush+0xd4/0x6d0 [bcache] [ 563.915812] process_one_work+0x856/0x1620 [ 564.001226] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 564.033563] ? find_held_lock+0x39/0x1d0 [ 564.033567] ? drain_workqueue+0x380/0x380 [ 564.033574] worker_thread+0x87/0xb80 [ 564.062823] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 564.118042] ? __kthread_parkme+0xb6/0x180 [ 564.118046] ? process_one_work+0x1620/0x1620 [ 564.118048] kthread+0x326/0x3e0 [ 564.118050] ? kthread_create_worker_on_cpu+0xc0/0xc0 [ 564.167066] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 564.252441] ret_from_fork+0x3a/0x50 [ 564.252447] Modules linked in: msr rpcrdma sunrpc rdma_ucm ib_iser ib_umad rdma_cm ib_ipoib i40iw configfs iw_cm ib_cm libiscsi scsi_transport_iscsi mlx4_ib ib_uverbs mlx4_en ib_core nls_iso8859_1 nls_cp437 vfat fat intel_rapl skx_edac x86_pkg_temp_thermal coretemp iTCO_wdt iTCO_vendor_support crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel ses raid0 aesni_intel cdc_ether enclosure usbnet ipmi_ssif joydev aes_x86_64 i40e scsi_transport_sas mii bcache md_mod crypto_simd mei_me ioatdma crc64 ptp cryptd pcspkr i2c_i801 mlx4_core glue_helper pps_core mei lpc_ich dca wmi ipmi_si ipmi_devintf nd_pmem dax_pmem nd_btt ipmi_msghandler device_dax pcc_cpufreq button hid_generic usbhid mgag200 i2c_algo_bit drm_kms_helper syscopyarea sysfillrect xhci_pci sysimgblt fb_sys_fops xhci_hcd ttm megaraid_sas drm usbcore nfit libnvdimm sg dm_multipath dm_mod scsi_dh_rdac scsi_dh_emc scsi_dh_alua efivarfs [ 564.299390] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree. [ 564.348360] CR2: 000000000000001c [ 564.348362] ---[ end trace b7f0e5cc7b2103b0 ]--- Therefore, it is not enough to only check whether c->gc_thread is NULL, we should use IS_ERR_OR_NULL() to check both NULL pointer and error value. This patch changes the above buggy code piece in this way, if (!IS_ERR_OR_NULL(c->gc_thread)) kthread_stop(c->gc_thread); Signed-off-by: -
Coly Li authored
When gc is running, user space I/O processes may wait inside bcache code, so no new I/O coming. Indeed this is not a real idle time, maximum writeback rate should not be set in such situation. Otherwise a faster writeback thread may compete locks with gc thread and makes garbage collection slower, which results a longer I/O freeze period. This patch checks c->gc_mark_valid in set_at_max_writeback_rate(). If c->gc_mark_valid is 0 (gc running), set_at_max_writeback_rate() returns false, then update_writeback_rate() will not set writeback rate to maximum value even c->idle_counter reaches an idle threshold. Now writeback thread won't interfere gc thread performance. Signed-off-by:
-
- 27 Jun, 2019 1 commit
-
-
Damien Le Moal authored
bio_flush_dcache_pages() is unused. Remove it. Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by:
-
- 26 Jun, 2019 3 commits
-
-
Douglas Anderson authored
Some debug code suggested by Paolo was tripping when I did reboot stress tests. Specifically in bfq_bfqq_resume_state() "bic->saved_wr_start_at_switch_to_srt" was later than the current value of "jiffies". A bit of debugging showed that "bic->saved_wr_start_at_switch_to_srt" was actually 0 and a bit more debugging showed that was because we had run through the "unlikely" case in the bfq_bfqq_save_state() function. Let's init "saved_wr_start_at_switch_to_srt" in the unlikely case to something sane. NOTE: this fixes no known real-world errors. Reviewed-by:
Paolo Valente <paolo.valente@linaro.org> Reviewed-by:
Guenter Roeck <groeck@chromium.org> Signed-off-by:
Douglas Anderson <dianders@chromium.org> Signed-off-by:
-
https://github.com/liu-song-6/linuxJens Axboe authored
Pull single MD warning fix from Song. * 'md-next' of https://github.com/liu-song-6/linux: md/raid1: Fix a warning message in remove_wb()
-
Dan Carpenter authored
The WARN_ON() macro doesn't take an error message, it just takes a condition. I've changed this to use WARN(1, "...") instead. Fixes: 3e148a32 ("md/raid1: fix potential data inconsistency issue with write behind device") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Song Liu <songliubraving@fb.com>
-
- 25 Jun, 2019 7 commits
-
-
Paolo Valente authored
Consider, on one side, a bfq_queue Q that remains empty while in service, and, on the other side, the pending I/O of bfq_queues that, according to their timestamps, have to be served after Q. If an uncontrolled amount of I/O from the latter bfq_queues were dispatched while Q is waiting for its new I/O to arrive, then Q's bandwidth guarantees would be violated. To prevent this, I/O dispatch is plugged until Q receives new I/O (except for a properly controlled amount of injected I/O). Unfortunately, preemption breaks I/O-dispatch plugging, for the following reason. Preemption is performed in two steps. First, Q is expired and re-scheduled. Second, the new bfq_queue to serve is chosen. The first step is needed by the second, as the second can be performed only after Q's timestamps have been properly updated (done in the expiration step), and Q has been re-queued for service. This dependency is a consequence of the way how BFQ's scheduling algorithm is currently implemented. But Q is not re-scheduled at all in the first step, because Q is empty. As a consequence, an uncontrolled amount of I/O may be dispatched until Q becomes non empty again. This breaks Q's service guarantees. This commit addresses this issue by re-scheduling Q even if it is empty. This in turn breaks the assumption that all scheduled queues are non empty. Then a few extra checks are now needed. Signed-off-by:
-
Paolo Valente authored
BFQ enqueues the I/O coming from each process into a separate bfq_queue, and serves bfq_queues one at a time. Each bfq_queue may be served for at most timeout_sync milliseconds (default: 125 ms). This service scheme is prone to the following inaccuracy. While a bfq_queue Q1 is in service, some empty bfq_queue Q2 may receive I/O, and, according to BFQ's scheduling policy, may become the right bfq_queue to serve, in place of the currently in-service bfq_queue. In this respect, postponing the service of Q2 to after the service of Q1 finishes may delay the completion of Q2's I/O, compared with an ideal service in which all non-empty bfq_queues are served in parallel, and every non-empty bfq_queue is served at a rate proportional to the bfq_queue's weight. This additional delay is equal at most to the time Q1 may unjustly remain in service before switching to Q2. If Q1 and Q2 have the same weight, then this time is most likely negligible compared with the completion time to be guaranteed to Q2's I/O. In addition, first, one of the reasons why BFQ may want to serve Q1 for a while is that this boosts throughput and, second, serving Q1 longer reduces BFQ's overhead. As a conclusion, it is usually better not to preempt Q1 if both Q1 and Q2 have the same weight. In contrast, as Q2's weight or priority becomes higher and higher compared with that of Q1, the above delay becomes larger and larger, compared with the I/O completion times that have to be guaranteed to Q2 according to Q2's weight. So reducing this delay may be more important than avoiding the costs of preempting Q1. Accordingly, this commit preempts Q1 if Q2 has a higher weight or a higher priority than Q1. Preemption causes Q1 to be re-scheduled, and triggers a new choice of the next bfq_queue to serve. If Q2 really is the next bfq_queue to serve, then Q2 will be set in service immediately. This change reduces the component of the I/O latency caused by the above delay by about 80%. For example, on an (old) PLEXTOR PX-256M5 SSD, the maximum latency reported by fio drops from 15.1 to 3.2 ms for a process doing sporadic random reads while another process is doing continuous sequential reads. Signed-off-by:
Nicola Bottura <bottura.nicola95@gmail.com> Signed-off-by:
-
Paolo Valente authored
A bfq_queue Q may happen to be synchronized with another bfq_queue Q2, i.e., the I/O of Q2 may need to be completed for Q to receive new I/O. We call Q2 "waker queue". If I/O plugging is being performed for Q, and Q is not receiving any more I/O because of the above synchronization, then, thanks to BFQ's injection mechanism, the waker queue is likely to get served before the I/O-plugging timeout fires. Unfortunately, this fact may not be sufficient to guarantee a high throughput during the I/O plugging, because the inject limit for Q may be too low to guarantee a lot of injected I/O. In addition, the duration of the plugging, i.e., the time before Q finally receives new I/O, may not be minimized, because the waker queue may happen to be served only after other queues. To address these issues, this commit introduces the explicit detection of the waker queue, and the unconditional injection of a pending I/O request of the waker queue on each invocation of bfq_dispatch_request(). One may be concerned that this systematic injection of I/O from the waker queue delays the service of Q's I/O. Fortunately, it doesn't. On the contrary, next Q's I/O is brought forward dramatically, for it is not blocked for milliseconds. Reported-by:
Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu> Tested-by:
-
Paolo Valente authored
Until the base value for request service times gets finally computed for a bfq_queue, the inject limit for that queue does depend on the think-time state (short|long) of the queue. A timely update of the think time then guarantees a quicker activation or deactivation of the injection. Fortunately, the think time of a bfq_queue is updated in the same code path as the inject limit; but after the inject limit. This commits moves the update of the think time before the update of the inject limit. For coherence, it moves the update of the seek time too. Reported-by:
-
Paolo Valente authored
I/O injection gets reduced if it increases the request service times of the victim queue beyond a certain threshold. The threshold, in its turn, is computed as a function of the base service time enjoyed by the queue when it undergoes no injection. As a consequence, for injection to work properly, the above base value has to be accurate. In this respect, such a value may vary over time. For example, it varies if the size or the spatial locality of the I/O requests in the queue change. It is then important to update this value whenever possible. This commit performs this update. Reported-by:
-
Paolo Valente authored
One of the cases where the parameters for injection may be updated is when there are no more in-flight I/O requests. The number of in-flight requests is stored in the field bfqd->rq_in_driver of the descriptor bfqd of the device. So, the controlled condition is bfqd->rq_in_driver == 0. Unfortunately, this is wrong because, the instruction that checks this condition is in the code path that handles the completion of a request, and, in particular, the instruction is executed before bfqd->rq_in_driver is decremented in such a code path. This commit fixes this issue by just replacing 0 with 1 in the comparison. Reported-by:
-
Paolo Valente authored
Until the base value of the request service times gets finally computed for a bfq_queue, the inject limit does depend on the think-time state (short|long). The limit must be 0 or 1 if the think time is deemed, respectively, as short or long. However, such a check and possible limit update is performed only periodically, once per second. So, to make the injection mechanism much more reactive, this commit performs the update also every time the think-time state changes. In addition, in the following special case, this commit lets the inject limit of a bfq_queue bfqq remain equal to 1 even if bfqq's think time is short: bfqq's I/O is synchronized with that of some other queue, i.e., bfqq may receive new I/O only after the I/O of the other queue is completed. Keeping the inject limit to 1 allows the blocking I/O to be served while bfqq is in service. And this is very convenient both for bfqq and for the total throughput, as explained in detail in the comments in bfq_update_has_short_ttime(). Reported-by:
-
- 24 Jun, 2019 1 commit
-
-
git://git.infradead.org/nvmeJens Axboe authored
Pull NVMe updates from Christoph: "A large chunk of NVMe updates for 5.3. Highlights: - improved PCIe suspent support (Keith Busch) - error injection support for the admin queue (Akinobu Mita) - Fibre Channel discovery improvements (James Smart) - tracing improvements including nvmetc tracing support (Minwoo Im) - misc fixes and cleanups (Anton Eidelman, Minwoo Im, Chaitanya Kulkarni)" * 'nvme-5.3' of git://git.infradead.org/nvme: (26 commits) Documentation: nvme: add an example for nvme fault injection nvme: enable to inject errors into admin commands nvme: prepare for fault injection into admin commands nvmet: introduce target-side trace nvme-trace: print result and status in hex format nvme-trace: support for fabrics commands in host-side nvme-trace: move opcode symbol print to nvme.h nvme-trace: do not export nvme_trace_disk_name nvme-pci: clean up nvme_remove_dead_ctrl a bit nvme-pci: properly report state change failure in nvme_reset_work nvme-pci: set the errno on ctrl state change error nvme-pci: adjust irq max_vector using num_possible_cpus() nvme-pci: remove queue_count_ops for write_queues and poll_queues nvme-pci: remove unnecessary zero for static var nvme-pci: use host managed power state for suspend nvme: introduce nvme_is_fabrics to check fabrics cmd nvme: export get and set features nvme: fix possible io failures when removing multipathed ns nvme-fc: add message when creating new association lpfc: add sysfs interface to post NVME RSCN ...
-
- 21 Jun, 2019 19 commits
-
-
Akinobu Mita authored
This adds an example of how to inject errors into admin commands. Suggested-by:
Thomas Tai <thomas.tai@oracle.com> Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Reviewed-by:
Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Reviewed-by:
Minwoo Im <minwoo.im@samsung.com> Reviewed-by:
-
Akinobu Mita authored
This enables to inject errors into the commands submitted to the admin queue. It is useful to test error handling in the controller initialization. # echo 100 > /sys/kernel/debug/nvme0/fault_inject/probability # echo 1 > /sys/kernel/debug/nvme0/fault_inject/times # echo 10 > /sys/kernel/debug/nvme0/fault_inject/space # nvme reset /dev/nvme0 # dmesg ... nvme nvme0: Could not set queue count (16385) nvme nvme0: IO queues not created Signed-off-by:
Minwoo Im <minwoo.im.dev@gmail.com> Reviewed-by:
Sagi Grimberg <sagi@grimberg.me> Reviewed-by:
-
Akinobu Mita authored
Currenlty fault injection support for nvme only enables to inject errors into the commands submitted to I/O queues. In preparation for fault injection into the admin commands, this makes the helper functions independent of struct nvme_ns. Signed-off-by:
-
Minwoo Im authored
This patch introduces target-side request tracing. As Christoph suggested, the trace would not be in a core or module to avoid disadvantages like cache miss: http://lists.infradead.org/pipermail/linux-nvme/2019-June/024721.html The target-side trace code is entirely based on the Johannes's trace code from the host side. It has lots of codes duplicated, but it would be better than having advantages mentioned above. It also traces not only fabrics commands, but also nvme normal commands. Once the codes to be shared gets bigger, then we can make it common as suggsted. This also removed the create_sq and create_cq trace parsing functions because it will be done by the connect fabrics command. Example: echo 1 > /sys/kernel/debug/tracing/event/nvmet/nvmet_req_init/enable echo 1 > /sys/kernel/debug/tracing/event/nvmet/nvmet_req_complete/enable cat /sys/kernel/debug/tracing/trace Signed-off-by:
-
Geert Uytterhoeven authored
With gcc 4.1: drivers/lightnvm/core.c: In function ‘nvm_remove_tgt’: drivers/lightnvm/core.c:510: warning: ‘t’ is used uninitialized in this function Indeed, if no NVM devices have been registered, t will be an uninitialized pointer, and may be dereferenced later. A call to nvm_remove_tgt() can be triggered from userspace by issuing the NVM_DEV_REMOVE ioctl on the lightnvm control device. Fix this by preinitializing t to NULL. Fixes: 843f2edb ("lightnvm: do not remove instance under global lock") Signed-off-by:Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
Matias Bjørling <mb@lightnvm.io> Signed-off-by:
-
Heiner Litz authored
bio_add_pc_page() may merge pages when a bio is padded due to a flush. Fix iteration over the bio to free the correct pages in case of a merge. Signed-off-by:
Heiner Litz <hlitz@ucsc.edu> Reviewed-by:
Javier González <javier@javigon.com> Signed-off-by:
-
Minwoo Im authored
The "result" field is in 64bit to be printed out which means it could be like: nvme_complete_rq: nvme0: qid=0, cmdid=0, res=18446612684158962624, etries=0, flags=0x0, status=0 Switch both the result and status field to be printed in hexadecimal format to be easier to read. Signed-off-by:
-
Minwoo Im authored
This patch introduces fabrics commands tracing feature from host-side. This patch does not include any changes for the previous host-side tracing, but just add fabrics commands parsing in cmd=() format. Signed-off-by:
-
Minwoo Im authored
The following patches are going to provide the target-side trace which might need these kind of macros. It would be great if it can be shared between host and target side both. Signed-off-by:
-
Minwoo Im authored
nvme_trace_disk_name() is now already being invoked with the function prototype in trace.h. We don't need to export this symbol at all. The following patches are going to provide target-side trace feature with the exactly same function with this so that this patch removes the EXPORT_SYMBOL() for this function. Signed-off-by:
-
Chaitanya Kulkarni authored
Remove the status parameter o nvme_remove_dead_ctrl(), which is only used for printing it. We move the print message to the same function where actual error is occurring. Signed-off-by:
-
Minwoo Im authored
If the state change to NVME_CTRL_CONNECTING fails, the dmesg is going to be like: [ 293.689160] nvme nvme0: failed to mark controller CONNECTING [ 293.689160] nvme nvme0: Removing after probe failure status: 0 Even it prints the first line to indicate the situation, the second line is not proper because the status is 0 which means normally success of the previous operation. This patch makes it indicate the proper error value when it fails. [ 25.932367] nvme nvme0: failed to mark controller CONNECTING [ 25.932369] nvme nvme0: Removing after probe failure status: -16 This situation is able to be easily reproduced by: root@target:~# rmmod nvme && modprobe nvme && rmmod nvme Signed-off-by:
-
Chaitanya Kulkarni authored
This patch removes the confusing assignment of the variable result at the time of declaration and sets the value in error cases next to the places where the actual error is happening. Here we also set the result value to -ENODEV when we fail at the final ctrl state transition in nvme_reset_work(). Without this assignment result will hold 0 from nvme_setup_io_queue() and on failure 0 will be passed to he nvme_remove_dead_ctrl() from final state transition. Signed-off-by:
-
Minwoo Im authored
If the "irq_queues" are greater than num_possible_cpus(), nvme_calc_irq_sets() can have irq set_size for HCTX_TYPE_DEFAULT greater than it can be afforded. 2039 affd->set_size[HCTX_TYPE_DEFAULT] = nrirqs - nr_read_queues; It might cause a WARN() from the irq_build_affinity_masks() like [1]: 220 if (nr_present < numvecs) 221 WARN_ON(nr_present + nr_others < numvecs); This patch prevents it from the WARN() by adjusting the max_vector value from the nvme_setup_irqs(). [1] WARN messages when modprobe nvme write_queues=32 poll_queues=0: root@target:~/nvme# nproc 8 root@target:~/nvme# modprobe nvme write_queues=32 poll_queues=0 [ 17.925326] nvme nvme0: pci function 0000:00:04.0 [ 17.940601] WARNING: CPU: 3 PID: 1030 at kernel/irq/affinity.c:221 irq_create_affinity_masks+0x222/0x330 [ 17.940602] Modules linked in: nvme nvme_core [last unloaded: nvme] [ 17.940605] CPU: 3 PID: 1030 Comm: kworker/u17:4 Tainted: G W 5.1.0+ #156 [ 17.940605] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 [ 17.940608] Workqueue: nvme-reset-wq nvme_reset_work [nvme] [ 17.940609] RIP: 0010:irq_create_affinity_masks+0x222/0x330 [ 17.940611] Code: 4c 8d 4c 24 28 4c 8d 44 24 30 e8 c9 fa ff ff 89 44 24 18 e8 c0 38 fa ff 8b 44 24 18 44 8b 54 24 1c 5a 44 01 d0 41 39 c4 76 02 <0f> 0b 48 89 df 44 01 e5 e8 f1 ce 10 00 48 8b 34 24 44 89 f0 44 01 [ 17.940611] RSP: 0018:ffffc90002277c50 EFLAGS: 00010216 [ 17.940612] RAX: 0000000000000008 RBX: ffff88807ca48860 RCX: 0000000000000000 [ 17.940612] RDX: ffff88807bc03800 RSI: 0000000000000020 RDI: 0000000000000000 [ 17.940613] RBP: 0000000000000001 R08: ffffc90002277c78 R09: ffffc90002277c70 [ 17.940613] R10: 0000000000000008 R11: 0000000000000001 R12: 0000000000000020 [ 17.940614] R13: 0000000000025d08 R14: 0000000000000001 R15: ffff88807bc03800 [ 17.940614] FS: 0000000000000000(0000) GS:ffff88807db80000(0000) knlGS:0000000000000000 [ 17.940616] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 17.940617] CR2: 00005635e583f790 CR3: 000000000240a000 CR4: 00000000000006e0 [ 17.940617] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 17.940618] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 17.940618] Call Trace: [ 17.940622] __pci_enable_msix_range+0x215/0x540 [ 17.940623] ? kernfs_put+0x117/0x160 [ 17.940625] pci_alloc_irq_vectors_affinity+0x74/0x110 [ 17.940626] nvme_reset_work+0xc30/0x1397 [nvme] [ 17.940628] ? __switch_to_asm+0x34/0x70 [ 17.940628] ? __switch_to_asm+0x40/0x70 [ 17.940629] ? __switch_to_asm+0x34/0x70 [ 17.940630] ? __switch_to_asm+0x40/0x70 [ 17.940630] ? __switch_to_asm+0x34/0x70 [ 17.940631] ? __switch_to_asm+0x40/0x70 [ 17.940632] ? nvme_irq_check+0x30/0x30 [nvme] [ 17.940633] process_one_work+0x20b/0x3e0 [ 17.940634] worker_thread+0x1f9/0x3d0 [ 17.940635] ? cancel_delayed_work+0xa0/0xa0 [ 17.940636] kthread+0x117/0x120 [ 17.940637] ? kthread_stop+0xf0/0xf0 [ 17.940638] ret_from_fork+0x3a/0x50 [ 17.940639] ---[ end trace aca8a131361cd42a ]--- [ 17.942124] nvme nvme0: 7/1/0 default/read/poll queues Signed-off-by:
-
Minwoo Im authored
queue_count_set() seems like that it has been provided to limit the number of queue entries for write/poll queues. But, the queue_count_set() has been doing nothing but a parameter check even it has num_possible_cpus() which is nop. This patch removes entire queue_count_ops from the write_queues and poll_queues. Signed-off-by:
-
Minwoo Im authored
poll_queues will be zero even without zero initialization here. Signed-off-by:
-
Keith Busch authored
The nvme pci driver prepares its devices for power loss during suspend by shutting down the controllers. The power setting is deferred to pci driver's power management before the platform removes power. The suspend-to-idle mode, however, does not remove power. NVMe devices that implement host managed power settings can achieve lower power and better transition latencies than using generic PCI power settings. Try to use this feature if the platform is not involved with the suspend. If successful, restore the previous power state on resume. Tested-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Tested-by:
Mario Limonciello <mario.limonciello@dell.com> Reviewed-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
Keith Busch <keith.busch@intel.com> Signed-off-by:
-
Minwoo Im authored
This patch introduces a nvme_is_fabrics() inline function to check whether or not the given command structure is for fabrics. Signed-off-by:
-
Keith Busch authored
Future use intends to make use of both, so export these functions. And since their implementation is identical except for the opcode, provide a new function that implement both. [akinobu.mita@gmail.com>: fix line over 80 characters] Signed-off-by:
-
