Use drivers/misc/sram.c driver to manage SRAM on all DT only
OMAP platforms (am33xx, am43xx, omap4 and omap5) instead of
the existing private plat-omap/sram.c

Address and size related data  is removed from mach-omap2/sram.c
and now passed to drivers/misc/sram.c from DT.

Users can hence use general purpose allocator apis instead of
OMAP private ones to manage and use SRAM.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Remove the empty am33xx_sram_init() function.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Now that we have panel support for DT based booting,
let's make it usable and enable most things as modules.

Note that omap3 boards need also the ads7847 module for
the panel that we're now changing to a loadable module.
And n900 seems to require setting the brightness via
sysfs for acx565akm/brightness after modprobe of
panel_sony_acx565akm and omapfb.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Since many omaps run on battery, we should have the battery
drivers enabled. Let's also enable the reset driver.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Some distros are now using systemd, so let's enable most of
what's recommended at:

http://cgit.freedesktop.org/systemd/systemd/tree/READMEReviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Note that we can now use the CONFIG_GENERIC_CPUFREQ_CPU0,
so let's only enable that. Let's use CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND
as suggested by Nishant.

And also let's enable thermal as explained by Nishant Menon:

Many TI SoCs using Highest frequency is not really too nice of an idea for
long periods of time. And not everything is upstream to support things
optimially - example avs class 0, 1.5 ABB consolidation with cpufreq etc..
We definitely need thermal enabled as well for device safety needs.

[tony@atomide.com: updated per Nishant's suggestions]
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This saves few lines and makes it easier to make patches
against omap2plus_defconfig.
Signed-off-by: Tony Lindgren <tony@atomide.com>

In sprz318f.pdf "Usage Note 2.7" says that UARTs cannot acknowledge
idle requests in smartidle mode when configured for DMA operations.
This prevents L4 from going idle. So let's use manual idle mode
instead.

Otherwise systems using Sebastian's 8250 patches with DMA will
never enter deeper idle states because of the errata above.

Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Commit cc824534 ("ARM: OMAP2+: hwmod: Rearm wake-up interrupts
for DT when MUSB is idled") fixed issues with hung UART wake-up
events by calling _reconfigure_io_chain() when MUSB is connected
or disconnected.

As pointed out by Paul Walmsley, we may need to also call
_reconfigure_io_chain() in other cases, so it should be a separate
flag. Let's add HWMOD_RECONFIG_IO_CHAIN as suggested by Paul.
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

OMAP4, OMAP5 and DRA7 share a lot of common logic and data structures.
These have been enabled in the previous patches, however, this also
means that OMAP5 or DRA7 only builds also need to build OMAP4 logic.
Update to reuse OMAP4 logic.

This fixes the 'undefined reference to 'omap4_pm_init_early'' in
OMAP5 or DRA7 only builds.

Fixes: 6af16a1d ("ARM: DRA7: Add hook in SoC initcalls to enable pm initialization")
Fixes: 628ed471 ("ARM: OMAP5: Add hook in SoC initcalls to enable pm initialization")
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Provide OMAP3, 4 and OMAP5 with interrupt number for PRM

And for DRA7, provide crossbar number for prm interrupt.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

OPP is now a normal kernel library selected by its users rather than a
feature that architectures need to enable so ARCH_HAS_OPP serves no
function any more - remove the selects.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

With consolidated code, now we can add the required hooks for
DRA7 to enable power management.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[nm@ti.com: minor modifications]
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Merge branch 'pull/v3.18/for-omap-soc' of https://github.com/nmenon/linux-2.6-playground into omap-for-v3.18/soc

Merge branch 'pull/v3.18/powerdomain-fixes' of https://github.com/nmenon/linux-2.6-playground into omap-for-v3.18/fixes-not-urgent

With consolidated code, now we can add the required hooks for
OMAP5 to enable power management.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[nm@ti.com: minor rebase updates]
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>

On OMAP5 / DRA7, prevent a CPU powerdomain OFF and resulting MPU OSWR
and instead attempt a CPU RET and side effect, MPU RET in suspend.

NOTE: the hardware was originally designed to be capable of achieving
deep power states such as OFF and OSWR, however due to various issues
and risks, deepest valid state was determined to be CSWR - hence we use
the errata framework to handle this case.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[nm@ti.com: updates]
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>

Dont assume that all OMAP4+ code will be able to use OMAP4 hotplug
logic. On OMAP5, DRA7, we do not need this in place yet, also,
currently the CPU startup pointer is located in omap4_cpu_pm_info
instead of cpu_pm_ops.

So, isolate the function to hotplug_restart pointer in cpu_pm_ops
where it should have belonged, initalize them as per valid startup
pointers for OMAP4430/60 as in current logic, however provide
dummy_cpu_resume to be the startup location as well.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[nm@ti.com: split this out of original code and isolate it]
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>

Get rid of all assumptions about always having a sar base on *all*
OMAP4+ platforms. We dont need one on DRA7 and it is not necessary at
this point for OMAP5 either.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[nm@ti.com: Split and optimize]
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>

In addition to the standard power-management technique, the OMAP5 / DRA7
MPU subsystem also employs an SR3-APG (mercury) power management
technology to reduce leakage.

It allows for full logic and memories retention on MPU_C0 and MPU_C1 and
is controlled by the PRCM_MPU. Only "Fast-mode" is supported on the
OMAP5 and DRA7 family of processors.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[nm@ti.com: minor consolidation]
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>

Enables MPUSS ES2 power management mode using ES2_PM_MODE in
AMBA_IF_MODE register.

0x0: OMAP5 ES1 behavior, CPU cores would enter and exit OFF mode together.
     Broken! Fortunately, we do not support this anymore.
0x1: OMAP5 ES2, DRA7 behavior, CPU cores are allowed to enter/exit OFF mode
     independently.

This is one time settings thanks to always ON domain.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[nm@ti.com: minor conflict resolutions, consolidation for DRA7]
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>

With EMIF clock-domain put under hardware supervised control, memory
corruption and untraceable crashes are observed on OMAP5. Further
investigation revealed that there is a weakness in the PRCM on this
specific dynamic depedency.

The recommendation is to set MPUSS static dependency towards EMIF
clock-domain to avoid issues. This recommendation holds good for DRA7
family of devices as well.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[rnayak@ti.com: DRA7]
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[nm@ti.com: conflict resolution, dra7]
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>

On OMAP5, RM_CPUi_CPUi_CONTEXT offset has changed. Update the code
so that same code works for OMAP4+ devices. DRA7 and OMAP5 have the same
context offset as well.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[rnayak@ti.com: for DRA7]
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[nm@ti.com: rebase, split/merge etc..]
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>

Provide pdata-quirks for Am437x processor family.
Signed-off-by: Keerthy <j-keerthy@ti.com>

Provide pdata-quirks for DRA7 processor family.
Signed-off-by: Nishanth Menon <nm@ti.com>

Provide pdata-quirks for OMAP5 processor family.
Signed-off-by: Nishanth Menon <nm@ti.com>

Not all SoCs support OFF mode - for example DRA74/72. So, use valid
power state during CPU hotplug.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

We are using power domain state as RET and logic state as OFF. This
state is OSWR. This may not always be supported on ALL power domains. In
fact, on certain power domains, this might result in a hang on certain
platforms. Instead, depend on powerdomain data to provide accurate
information about the supported powerdomain states and use the
appropriate function to query and use it as part of suspend path.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Move the logic state as different for each power domain. This allows us
to customize the deepest power state we should target over all for each
powerdomain in the follow on patches.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

powerdomain configuration in OMAP is done using PWRSTCTRL register for
each power domain. However, PRCM lets us write any value we'd like to
the logic and power domain target states, however the SoC integration
tends to actually function only at a few discrete states. These valid
states are already in our powerdomains_xxx_data.c file.

So, provide a function to easily query valid low power state that the
power domain is allowed to go to.

Based on work originally done by Jean Pihet <j-pihet@ti.com>
https://patchwork.kernel.org/patch/1325091/ . There is no attempt to
create a new powerdomain solution here, except fixing issues seen
attempting invalid programming attempts. Future consolidation to the
generic powerdomain framework should consider this requirement as
well.

Similar solutions have been done in product kernels in the past such
as:
https://android.googlesource.com/kernel/omap.git/+blame/android-omap-panda-3.0/arch/arm/mach-omap2/pm44xx.cSigned-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

No need to invoke callback when the clkdm pointer is NULL.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Update the power domain power states for final production chip
capability. OFF mode, OSWR etc have been descoped for various domains.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

DRA7 supports only CSWR for CPU, MPU power domains. Core power domain
supports upto INA.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Allow the PRM interrupt information to be picked up from device tree.
OMAP3 may use legacy boot and needs to be compatible with old dtbs
(without interrupt populated), for these, we use the value which is
pre-populated.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

OMAP5 and DRA7 can now use pinctrl based I/O daisychain wakeup
capability. So, enable the support.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

"wkup" event at bit offset 0 exists only on OMAP3.
OMAP4430/60 PRM_IRQSTATUS_A9, OMAP5/DRA7 PRM_IRQSTATUS_MPU

register bit 0 is DPLL_CORE_RECAL_ST not wakeup event like OMAP3.

The same applies to AM437x as well.

Remove the wrong definition.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Allow the PRM interrupt information to be picked up from device tree.
the only exception is for OMAP4 which uses values pre-populated and allows
compatibility with older dtb.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

use the generic function to pick up the prm_instance for a generic logic
which can be reused from OMAP4+
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

PRM device instance can vary depending on SoC. We already handle the
same during reset of the device, However, this is also needed
for other logic instances. So, first abstract this out to a generic
function.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Beaglebone white and beaglebone black differ in tiny little aspects.
This is the reason why we maintain seperate dts for these platforms.
However, there is no real way to decode from dtb which platform it is
since compatible and model name are the same for both platforms.

Fix this so that beaglebone black and beaglebone are identifiable,
while maintaining compatibility for older zImages which might use old
beaglebone compatible flag for black as well.
Reported-by: Tom Rini <trini@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>