Simplify the Yamp device tree by using the common dtsi.

In addition this enables the following the second firmware flash and the
eMMC device in slot #1.
Signed-off-by: Tao Ren <taoren@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Simplify the Minipack device tree by using the common dtsi.

In addition this enables the enabling the second firmware flash, and
updates it's size from 32MB to 64MB. It also enables the eMMC device in
slot #1.
Signed-off-by: Tao Ren <taoren@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Simplify the CMM device tree by using the common dtsi.

In addition this enables the second firmware flash and the emmc device
in slot #0.
Signed-off-by: Tao Ren <taoren@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

This common descirption is included by all Facebook AST2500 Network BMC
platforms to minimize duplicated device entries across Facebook Network
BMC device trees.
Signed-off-by: Tao Ren <taoren@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Add in a gpio-keys section to the Rainier device tree source, add in the
power supply presence GPIOs.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Fix the size of the Proc VRM card's eeprom used for vpd storage. The
size is changed from 64Kbit to 128Kbit.
Signed-off-by: Jinu Joy Thomas <jinu.joy.thomas@in.ibm.com>
Reviewed-by: Santosh Puranik <santosh.puranik.ibm@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Requesting pinmux configuration is done at driver probe time. The LPC IP
is composed of many sub-devices, each with their own driver, and no
driver exists for the entire IP block. Avoid having each sub-device
request the LPC pinmux by just hogging it in the pinctrl node.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Like most OpenPower machines the VUART is expected to be at /dev/ttyS5
for communication with the host over LPC.
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Added eeproms for the below VPD devices
- BMC
- TPM
- System Planar
- DCM 0 VRM
- DCM 1 VRM
- Base Op panel
- Lcd Op panel
- DASD (All)
- PCIe Cards (All)
Signed-off-by: Jinu Joy Thomas <jinu.joy.thomas@in.ibm.com>
Reviewed-by: Santosh Puranik <santosh.puranik.ibm@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

OpenBMC requires a window the same size as the image being loaded.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

This adds the description of the Power9 CPUs that are attached to the
BMC.
Signed-off-by: Joel Stanley <joel@jms.id.au>

The UART has an issue on A0 that can be worked around by using the
Synopsis driver.
Tested-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

The UARTs on the AST2600 A0 have a known issue that can be worked around
by using the Synopsys driver.
Tested-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

The AST2600 has five UARTs. Add UART 1 to 4.
Tested-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

The upstream clock for the I2C buses is APB2.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

We need to ungate RCLK on AST2500- and AST2600-based platforms for RMII
to function. RMII interfaces are commonly used for NCSI.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

This contains the dt-bindings headers for the ethernet clocks.
Signed-off-by: Joel Stanley <joel@jms.id.au>

Tacoma has two SPI flash devices attached to the FMC, and one on the SPI
controller.
Signed-off-by: Joel Stanley <joel@jms.id.au>

Add fan controllers, regulators, temperature sensors, power supplies
and regulators.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

The ast2600 has two FSI masters on the APB.
Signed-off-by: Joel Stanley <joel@jms.id.au>

Keep the FMC controller chips at a safe 50 MHz rate and use 100 MHz
for the PNOR on the machines using a AST2500 SoC.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Use the SoC-specific compatible strings instead.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Adds a new power_green led to show the host state.
Signed-off-by: Alexander Filippov <a.filippov@yadro.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Add gpio-keys for various signals on Tacoma.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

All 2600-evb MACs use RGMII/MDIO.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

This way enabling the MDIO controllers automatically requests the right
pinmux configuration.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

The binding was updated to better reflect the intended use of the
hardware and the existing function/groups for SD3 were dropped.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

The AST2600 u-boot and kernel images have outgrown the OpenBMC layout.
While BMC machines use 128MB SPI NOR chips, we only have 64MB on the EVB
so use a layout that has a smaller region for the ro and rw filesystems.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Tacoma has two SPI flash devices attached to the FMC, and one on the SPI
controller.
Signed-off-by: Joel Stanley <joel@jms.id.au>

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Add fan controllers, regulators, temperature sensors, power supplies
and regulators.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Rainier contains two NCSI network devices.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Rainier is a new IBM server with POWER host processors and an AST2600
BMC.
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

This is an alternate layout used by OpenBMC systems that require more
space on the BMC's flash. In addition to more space for the rootfs, it
supports a larger u-boot and Linux kernel FIT image.

The division of space is as follows:

 u-boot + env: 1MB
 kernel/FIT: 9MB
 rwfs: 86MB
 rofs: 32MB
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Change BMC init-ok from GPIO to LED, which needs to blink when BMC
initialization is complete.

Use TAB to align some lines.
Signed-off-by: Chicago Duan <duanzhijia01@inspur.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Enable all the I2C busses on Tacoma and add the I2C slave devices that
exist on the busses.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>

This is an AST2600 based BMC card for a Power9 system.
Signed-off-by: Joel Stanley <joel@jms.id.au>

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Everything is the same as G5, except the devices have their own
interrupt now.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>