An error occurred fetching the project authors.
- 20 Sep, 2018 12 commits
-
-
Grygorii Strashko authored
The phy_id property is deprecated and phy-handle has to be used instead. Signed-off-by:
Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Grygorii Strashko authored
The phy_id property is deprecated and phy-handle has to be used instead. Signed-off-by:
-
Grygorii Strashko authored
The phy_id property is deprecated and phy-handle has to be used instead. Signed-off-by:
-
Grygorii Strashko authored
The phy_id property is deprecated and phy-handle has to be used instead. Signed-off-by:
-
Grygorii Strashko authored
The phy_id property is deprecated and phy-handle has to be used instead. Signed-off-by:
-
Grygorii Strashko authored
The phy_id property is deprecated and phy-handle has to be used instead. Signed-off-by:
-
Grygorii Strashko authored
The phy_id property is deprecated and phy-handle has to be used instead. Signed-off-by:
-
Grygorii Strashko authored
The phy_id property is deprecated and phy-handle has to be used instead. Signed-off-by:
-
Grygorii Strashko authored
The phy_id property is deprecated and phy-handle has to be used instead. Signed-off-by:
-
Grygorii Strashko authored
The phy_id property is deprecated and phy-handle has to be used instead. Signed-off-by:
-
Tony Lindgren authored
-
Grygorii Strashko authored
am335x-evm has only one CPSW external port physically wired, but DT defines 2 ext. ports. As result, PHY connection failure reported for the second ext. port. Update DT to reflect am335x-evm board HW configuration, and, while here, switch to use phy-handle instead of phy_id. Signed-off-by:
-
- 07 Sep, 2018 28 commits
-
-
Andrew F. Davis authored
The SN65HVS882 load trigger is attached to GPIO2_23 on the AM571x IDK. Signed-off-by:
Andrew F. Davis <afd@ti.com> Signed-off-by:
-
Andrew F. Davis authored
AM572x-IDK rev 1.3A has tricolor RGB LEDs that can be controlled using GPIO. Expose these to userspace for usage as necessary. Signed-off-by:
-
Andrew F. Davis authored
AM571x-IDK rev 1.2A has tricolor RGB LEDs that can be controlled using GPIO. Expose these to userspace for usage as necessary. Signed-off-by:
-
H. Nikolaus Schaller authored
GTA04A5 has been produced with MCP chips either with 512MB RAM + 512MB NAND 512MB RAM + 1024MB NAND 1024MB RAM + 512MB OneNAND RAM setup is done by U-Boot (MLO/SPL) but OneNAND needs a different setup of the GPMC. So we need to derive a DTB variant that modifies the gpmc and nand setup. Signed-off-by:
H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by:
-
H. Nikolaus Schaller authored
Properly pinmux the bluetooth enable so that it is not floating. Signed-off-by:
-
H. Nikolaus Schaller authored
Sensors for acceleration, rotation, magnetic heading and barometer have been replaced in the A5 variant. Signed-off-by:
-
H. Nikolaus Schaller authored
GTA04A5 uses a ti,wl1837 WiFi/Bluetooth module. Overwrite the mmc2 node and child. Signed-off-by:
-
H. Nikolaus Schaller authored
The GTA04A5 has an improved IrDA circuit that can enable/disable the receiver individually. We do not have an IrDA driver/subsystem and hence the receiver should be actively turned off to save power, especially in suspend. Signed-off-by:
-
H. Nikolaus Schaller authored
GPS receiver provides a 1PPS signal to a gpio. Signed-off-by:
-
H. Nikolaus Schaller authored
in node sound / property ti,jack-det-gpio. Signed-off-by:
-
H. Nikolaus Schaller authored
GTA04 is the project name and Letux 2804 the product name. Report both. Signed-off-by:
-
H. Nikolaus Schaller authored
Signed-off-by:
-
H. Nikolaus Schaller authored
GTA04 is the project name and Letux 2804 the product name. Report both. Signed-off-by:
-
H. Nikolaus Schaller authored
GTA04 is the project name and Letux 2804 the product name. Report both. Signed-off-by:
-
H. Nikolaus Schaller authored
GTA04 audio system makes use of all four McBSP ports, so enable and connect them with pinmux. Signed-off-by:
-
H. Nikolaus Schaller authored
McBSP1 needs special "pinctrl" for the clocks. Signed-off-by:
-
H. Nikolaus Schaller authored
GTA04 audio system makes use of all four McBSP ports, so set up proper pinmux. Signed-off-by:
-
H. Nikolaus Schaller authored
ISP needs camera pinmux (which is referenced by the camera node). Signed-off-by:
-
H. Nikolaus Schaller authored
The GTA04 has an optional OV9655 camera (for which we do not yet have a driver upstream), but the ISP hardware connection description in the device tree is independent of that. Signed-off-by:
-
H. Nikolaus Schaller authored
GTA04 can detect presence/absence or plug-in of an external GPS antenna through a gpio. The best match for an event code is SW_LINEIN_INSERT. Signed-off-by:
-
H. Nikolaus Schaller authored
we can replace magic numbers by symbolic constants now. Signed-off-by:
-
H. Nikolaus Schaller authored
There are neither CD nor WP switches for mmc1. The µSD slot is located under the SIM card under the battery and not accessible during operation. Signed-off-by:
-
H. Nikolaus Schaller authored
vaux2 should remain always on since a higher potential at vio could potentially damage the itg3200 sensor. Signed-off-by:
-
H. Nikolaus Schaller authored
Make clear how to use the wifi_reset since it is not obvious. Signed-off-by:
-
H. Nikolaus Schaller authored
This is needed to make the display and venc work properly. Compare to omap3-beagle.dts. Signed-off-by:
-
H. Nikolaus Schaller authored
to better match omap3-beagle.dts (which was the basis of designing the GTA04). Signed-off-by:
-
H. Nikolaus Schaller authored
Vendor defined U-Boot has changed the partition scheme a while ago: * kernel partition 6MB * file system partition uses the remainder up to end of the NAND * increased size of the environment partition (to get an OneNAND compatible base address) * shrink the U-Boot partition Let's be compatible (e.g. Debian kernel built from upstream). Signed-off-by:
-
H. Nikolaus Schaller authored
Signed-off-by:
-
