The csa counter has moved from sdata to beacon/presp but
it is not updated accordingly for mesh and ibss. Fix this.

Fixes: af296bdb ("mac80211: move csa counters from sdata to beacon/presp")
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The last hop metric should refer to link cost (this is how
hwmp_route_info_get uses it for example). But in mesh_rx_path_sel_frame
we are not dealing with link cost but with the total cost to the origin
of a PREQ or PREP.
Signed-off-by: Alexis Green <agreen@cococorp.com>
CC: Jesse Jones <jjones@cococorp.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Channels in 2.4GHz band overlap, this means that if we
send a probe request on channel 1 and then move to channel
2, we will hear the probe response on channel 2. In this
case, the RSSI will be lower than if we had heard it on
the channel on which it was sent (1 in this case).

The scan result ignores those invalid values and the
station last signal should not be updated as well.

In case the scan determines the signal to be invalid turn on
the flag so the station last signal will not be updated with
the value and thus user space probing for NL80211_STA_INFO_SIGNAL
and NL80211_STA_INFO_SIGNAL_AVG will not get this invalid RSSI
value.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There were a few rare cases when upon
authentication failure channel wasn't released.
This could cause stale pointers to remain in
chanctx assigned_vifs after interface removal and
trigger general protection fault later.

This could be triggered, e.g. on ath10k with the
following steps:

 1. start an AP
 2. create 2 extra vifs on ath10k host
 3. connect vif1 to the AP
 4. connect vif2 to the AP
    (auth fails because ath10k firmware isn't able
     to maintain 2 peers with colliding AP mac
     addresses across vifs and consequently
     refuses sta_info_insert() in
     ieee80211_prep_connection())
 5. remove the 2 extra vifs
 6. goto step 2; at step 3 kernel was crashing:

 general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC
 Modules linked in: ath10k_pci ath10k_core ath
 ...
 Call Trace:
  [<ffffffff81a2dabb>] ieee80211_check_combinations+0x22b/0x290
  [<ffffffff819fb825>] ? ieee80211_check_concurrent_iface+0x125/0x220
  [<ffffffff8180f664>] ? netpoll_poll_disable+0x84/0x100
  [<ffffffff819fb833>] ieee80211_check_concurrent_iface+0x133/0x220
  [<ffffffff81a0029e>] ieee80211_open+0x3e/0x80
  [<ffffffff817f2d26>] __dev_open+0xb6/0x130
  [<ffffffff817f3051>] __dev_change_flags+0xa1/0x170
 ...
 RIP  [<ffffffff81a23140>] ieee80211_chanctx_radar_detect+0xa0/0x170

 (gdb) l * ieee80211_chanctx_radar_detect+0xa0
 0xffffffff81a23140 is in ieee80211_chanctx_radar_detect (/devel/src/linux/net/mac80211/util.c:3182).
 3177             */
 3178            WARN_ON(ctx->replace_state == IEEE80211_CHANCTX_REPLACES_OTHER &&
 3179                    !list_empty(&ctx->assigned_vifs));
 3180
 3181            list_for_each_entry(sdata, &ctx->assigned_vifs, assigned_chanctx_list)
 3182                    if (sdata->radar_required)
 3183                            radar_detect |= BIT(sdata->vif.bss_conf.chandef.width);
 3184
 3185            return radar_detect;
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

FIF_PROMISC_IN_BSS was removed in commit df140465
("mac80211: remove support for IFF_PROMISC").
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The conversion to the fast-xmit path lost proper aggregation session
timeout handling - the last_tx wasn't set on that path and the timer
would therefore incorrectly tear down the session periodically (with
those drivers/rate control algorithms that have a timeout.)

In case of iwlwifi, this was every 5 seconds and caused significant
throughput degradation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The naming convention is to always have the flags prefixed with
IEEE80211_HW_ so they're 'namespaced', make this flag follow it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There are no drivers setting IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE
or IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE, so any code using the
two flags is dead; it's also exceedingly unlikely that any new driver
could ever need to set these flags.

The wcn36xx code is almost certainly broken, but this preserves the
previous behaviour.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Even if the pointers are really only accessible to root and used
pretty much only by wpa_supplicant, this is still not great; even
for debugging it'd be easier to have something that's easier to
read and guaranteed to never get reused.

With the recent change to make mac80211 create an ack_skb for the
mgmt-tx path this becomes possible, only the client probe method
needs to also allocate an ack_skb, and we can store the cookie in
that skb.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When we return the TX status for an nl80211 mgmt TX SKB, we
should also return the original frame with the status to
allow userspace to match up the submission (it could also
use the cookie but both ways are permissible.)

As TX SKBs could be encrypted, at least in the case of ANQP
while associated with the AP, copy the original SKB, store
it with an ACK frame ID and restructure the status path to
use that to return status with the original SKB. Otherwise,
userspace (in particular wpa_supplicant) will get confused.
Reported-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

For drivers supporting TSO or similar features, but that still have
PN assignment in software, there's a need to have some memory to
store the current PN value. As mac80211 already stores this and it's
somewhat complicated to add a per-driver area to the key struct (due
to the dynamic sizing thereof) it makes sense to just move the TX PN
to the keyconf, i.e. the public part of the key struct.

As TKIP is more complicated and we won't able to offload it in this
way right now (fast-xmit is skipped for TKIP unless the HW does it
all, and our hardware needs MMIC calculation in software) I've not
moved that for now - it's possible but requires exposing a lot of
the internal TKIP state.

As an bonus side effect, we can remove a lot of code by assuming the
keyseq struct has a certain layout - with BUILD_BUG_ON to verify it.

This might also improve performance, since now TX and RX no longer
share a cacheline.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When trying to associate, the AP could send a deauth frame instead.
Currently mac80211 drops that frame and doesn't report it to the
supplicant, which, in some versions and/or in certain circumstances
will simply keep trying to associate over and over again instead of
trying authentication again.

Fix this by reacting to deauth frames while associating, reporting
them to the supplicant and dropping the association attempt (which
is bound to fail.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since 39b2bbe3 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.

Furthermore there is devm_gpiod_get_optional which is designed to get
optional gpios.

Simplify driver accordingly.

Note this makes error checking more strict because only -ENOENT is
ignored when searching for the GPIOs which is good.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

It was possible for mac80211 to be coerced into an
unexpected flow causing sdata union to become
corrupted. Station pointer was put into
sdata->u.vlan.sta memory location while it was
really master AP's sdata->u.ap.next_beacon. This
led to station entry being later freed as
next_beacon before __sta_info_flush() in
ieee80211_stop_ap() and a subsequent invalid
pointer dereference crash.

The problem was that ieee80211_ptr->use_4addr
wasn't cleared on interface type changes.

This could be reproduced with the following steps:

 # host A and host B have just booted; no
 # wpa_s/hostapd running; all vifs are down
 host A> iw wlan0 set type station
 host A> iw wlan0 set 4addr on
 host A> printf 'interface=wlan0\nssid=4addrcrash\nchannel=1\nwds_sta=1' > /tmp/hconf
 host A> hostapd -B /tmp/conf
 host B> iw wlan0 set 4addr on
 host B> ifconfig wlan0 up
 host B> iw wlan0 connect -w hostAssid
 host A> pkill hostapd
 # host A crashed:

 [  127.928192] BUG: unable to handle kernel NULL pointer dereference at 00000000000006c8
 [  127.929014] IP: [<ffffffff816f4f32>] __sta_info_flush+0xac/0x158
 ...
 [  127.934578]  [<ffffffff8170789e>] ieee80211_stop_ap+0x139/0x26c
 [  127.934578]  [<ffffffff8100498f>] ? dump_trace+0x279/0x28a
 [  127.934578]  [<ffffffff816dc661>] __cfg80211_stop_ap+0x84/0x191
 [  127.934578]  [<ffffffff816dc7ad>] cfg80211_stop_ap+0x3f/0x58
 [  127.934578]  [<ffffffff816c5ad6>] nl80211_stop_ap+0x1b/0x1d
 [  127.934578]  [<ffffffff815e53f8>] genl_family_rcv_msg+0x259/0x2b5

Note: This isn't a revert of f8cdddb8
("cfg80211: check iface combinations only when
iface is running") as far as functionality is
considered because b6a55015 ("cfg80211/mac80211:
move more combination checks to mac80211") moved
the logic somewhere else already.

Fixes: f8cdddb8 ("cfg80211: check iface combinations only when iface is running")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There was a possible race between
ieee80211_reconfig() and
ieee80211_delayed_tailroom_dec(). This could
result in inability to transmit data if driver
crashed during roaming or rekeying and subsequent
skbs with insufficient tailroom appeared.

This race was probably never seen in the wild
because a device driver would have to crash AND
recover within 0.5s which is very unlikely.

I was able to prove this race exists after
changing the delay to 10s locally and crashing
ath10k via debugfs immediately after GTK
rekeying. In case of ath10k the counter went below
0. This was harmless but other drivers which
actually require tailroom (e.g. for WEP ICV or
MMIC) could end up with the counter at 0 instead
of >0 and introduce insufficient skb tailroom
failures because mac80211 would not resize skbs
appropriately anymore.

Fixes: 8d1f7ecd ("mac80211: defer tailroom counter manipulation when roaming")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When we disconnect from the AP, drivers call cfg80211_disconnect().
This doesn't know whether the disconnection was initiated locally
or by the AP though, which can cause problems with the supplicant,
for example with WPS. This issue obviously doesn't show up with any
mac80211 based driver since mac80211 doesn't call this function.

Fix this by requiring drivers to indicate whether the disconnect is
locally generated or not. I've tried to update the drivers, but may
not have gotten the values correct, and some drivers may currently
not be able to report correct values. In case of doubt I left it at
false, which is the current behaviour.

For libertas, make adjustments as indicated by Dan Williams.
Reported-by: Matthieu Mauger <matthieux.mauger@intel.com>
Tested-by: Matthieu Mauger <matthieux.mauger@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When a station does a channel switch, it's not well defined what its TDLS
peers would do. Avoid a situation when the local side marks a potentially
disconnected peer as a TDLS peer.
Keeping peers connected through CSA is doubly problematic with the upcoming
TDLS WIDER-BW feature which allows peers to widen the BSS channel. The
new channel transitioned-to might not be compatible and would require
a re-negotiation anyway.

Make sure to disallow new TDLS link during CSA.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Drivers with fast-xmit (e.g. ath10k) running in
AP_VLAN setups would fail to communicate with
connected 4addr stations.

The reason was when new station associates it
first goes into master AP interface. It is not
until later that a dedicated AP_VLAN is created
for it and the station itself is moved there.
After that Tx directed at the station should use
4addr header. However fast-xmit wasn't
recalculated and 3addr header remained to be used.
This in turn caused the connected 4addr stations
to drop packets coming from the AP until some
other event would cause fast-xmit to recalculate
for that station (which could never come).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The kernel-doc description for the drv_priv member of
struct ieee80211_txq was missing, leading to errors.
Add a suitable description to fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Use dev_pm_ops instead of the legacy suspend/resume callbacks for the wiphy
class suspend and resume operations.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Use dev_pm_ops instead of the legacy suspend/resume callbacks for the
rfkill class suspend and resume operations.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

My recent change here introduced a possible memory leak if the
driver registers an invalid cipher schemes. This won't really
happen in practice, but fix the leak nonetheless.

Fixes: e3a55b53 ("mac80211: validate cipher scheme PN length better")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

As I was testing with hwsim, I missed that my previous commit to
make LED work depend on activation broke the code because I missed
removing the old trigger struct and some code was still using it,
now erroneously, causing crashes.

Fix this by always using the correct struct.
Reported-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The chandef of the current channel context might be wider (though
compatible). The TDLS link cares only about the channel of the BSS.

In addition make sure to specify the VHT operation IE when VHT is supported
on a non-2.4GHz band, as required by IEEE802.11ac-2013. This is not the
same as HT-operation, to be specified only if the BSS doesn't support HT.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When an IBSS station gets QoS enabled after having been added,
check fast-xmit to make sure the QoS header gets added to the
cache properly and frames can go out with QoS and higher rates.
Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When a vif starts using a reserved channel context (during CSA, for example)
the required chandef was recalculated, however it was never applied.
This could result in using chanctx with narrower width than actually
required. Fix this by calling ieee80211_change_chanctx with the recalculated
chandef. This both changes the chanctx's width and recalcs min_def.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This was missed in the previous patch, add some documentation
for rate_ctrl_lock to avoid docbook warnings.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The GO_CONCURRENT regulatory definition can be extended to station
interfaces requesting to IR as part of TDLS off-channel operations.
Rename the GO_CONCURRENT flag to IR_CONCURRENT and allow the added
use-case.

Change internal users of GO_CONCURRENT to use the new definition.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Declare that MCS 0-9 are supported for all Rx chains.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Previously, VHT capabilities and supported MCSs where set for all
bands, although VHT is only allowed on 5.2 GHz band. Fix it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If a P2P GO was allowed on a channel because of the GO concurrent
relaxation, i.e., another station interface was associated to an AP on
the same channel or the same UNII band, and the station interface
disconnected from the AP, allow the following use cases unless the
channel is marked as indoor only and the device is not operating in an
indoor environment:

1. Allow the P2P GO to stay on its current channel. The rationale behind
   this is that if the channel or UNII band were allowed by the AP they
   could still be used to continue the P2P GO operation, and avoid connection
   breakage.
2. Allow another P2P GO to start on the same channel or another channel
   that is in the same UNII band as the previous instantiated P2P GO.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Currently, a cipher scheme can advertise an arbitrarily long
sequence counter, but mac80211 only supports up to 16 bytes
and the initial value from userspace will be truncated.

Fix two things:
 * don't allow the driver to register anything longer than
   the 16 bytes that mac80211 reserves space for
 * require userspace to specify a starting value with the
   correct length (or none at all)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

For ciphers not supported by mac80211, the function currently
doesn't return any PN data. Fix this by extending the driver's
get_key_seq() a little more to allow moving arbitrary PN data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Extend the function to read the TKIP IV32/IV16 to read the IV/PN for
all ciphers in order to allow drivers with full hardware crypto to
properly support this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

No current (and planned, as far as I know) wifi devices support
encapsulation checksum offload, so remove the useless test here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When LED triggers are compiled in, but not used, mac80211 will still
call them to update the status. This isn't really a problem for the
assoc and radio ones, but the TX/RX (and to a certain extend TPT)
ones can be called very frequently (for every packet.)

In order to avoid that when they're not used, track their activation
and call the corresponding trigger (and in the TPT case, account for
throughput) only when the trigger is actually used by an LED.

Additionally, make those trigger functions inlines since theyre only
used once in the remaining code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This is just a code cleanup, make the LED trigger names const
as they're not expected to be modified by drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Remove items that can be retrieved through nl80211. This also
removes two items (tx_packets and tx_bytes) where only the VO
counter was exposed since they are split up per AC but in the
debugfs file only the first AC was shown.

Also remove the useless "dev" file - the stations have long
been in a sub-directory of the netdev so there's no need for
that any more.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This counter is unsafe with concurrent TX and is only exposed
through debugfs and ethtool. Instead of trying to fix it just
remove it for now, if it's really needed then it should be
exposed through nl80211 and in a way that drivers that do the
fragmentation in the device could support it as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since these counters can only be read through debugfs, there's
very little point in maintaining them all the time. However,
even just making them depend on debugfs is pointless - they're
not normally used. Additionally a number of them aren't even
concurrency safe.

Move them under MAC80211_DEBUG_COUNTERS so they're normally
not even compiled in.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>