ip6_datagram_recv_ctl and ip6_datagram_send_ctl are used for handling IPv6
ancillary data.  Since ip6_datagram_send_ctl is already publicly exported for
use in modules, ip6_datagram_recv_ctl should also be available to support
ancillary data in the receive path.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The datagram_*_ctl functions in net/ipv6/datagram.c are IPv6-specific.  Since
datagram_send_ctl is publicly exported it should be appropriately named to
reflect the fact that it's for IPv6 only.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add VID, PID and fixed interface for Telit LE920
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

They will be created at output, if ever needed. This avoids creating
empty neighbor entries when TPROXYing/Forwarding packets for addresses
that are not even directly reachable.

Note that IPv4 already handles it this way. No neighbor entries are
created for local input.

Tested by myself and customer.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A device sending 0 length frames as fast as it can has been
observed killing the host system due to the resulting memory
pressure.

Temporarily disable RX skb allocation and URB submission when
the current error ratio is high, preventing us from trying to
allocate an infinite number of skbs.  Reenable as soon as we
are finished processing the done queue, allowing the device
to continue working after short error bursts.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

vmxnet3 fails to set netif_carrier_off on probe, meaning that when an interface
is opened the __LINK_STATE_NOCARRIER bit is already cleared, and so
/sys/class/net/<ifname>/operstate remains in the unknown state.  Correct this by
setting netif_carrier_off on probe, like other drivers do.

Also, while we're at it, lets remove the netif_carrier_ok checks from the
link_state_update function, as that check is atomically contained within the
netif_carrier_[on|off] functions anyway

Tested successfully by myself
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In rare instances, memory errors have been detected in the internal packet
buffer memory on I217/I218 when stressed under certain environmental
conditions.  Enable Error Correcting Code (ECC) in hardware to catch both
correctable and uncorrectable errors.  Correctable errors will be handled
by the hardware.  Uncorrectable errors in the packet buffer will cause the
packet to be received with an error indication in the buffer descriptor
causing the packet to be discarded.  If the uncorrectable error is in the
descriptor itself, the hardware will stop and interrupt the driver
indicating the error.  The driver will then reset the hardware in order to
clear the error and restart.

Both types of errors will be accounted for in statistics counters.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: <stable@vger.kernel.org> # 3.5.x & 3.6.x
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When bonding module is loaded with primary parameter and one decides to unset
primary slave using sysfs these settings are not preserved during bond device
restart. Primary slave is only unset once and it's not remembered in
bond->params structure. Below is example of recreation.

 grep OPTS /etc/sysconfig/network-scripts/ifcfg-bond0
BONDING_OPTS="mode=active-backup miimon=100 primary=eth01"
 grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: eth01 (primary_reselect always)

 echo "" > /sys/class/net/bond0/bonding/primary
 grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: None

 sed -i -e 's/primary=eth01//' /etc/sysconfig/network-scripts/ifcfg-bond0
 grep OPTS /etc/sysconfig/network-scripts/ifcfg-bond
BONDING_OPTS="mode=active-backup miimon=100 "
 ifdown bond0 && ifup bond0

without patch:
 grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: eth01 (primary_reselect always)

with patch:
 grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: None
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Milos Vyletel <milos.vyletel@sde.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We drop a connection request if the accept backlog is full and there are
sufficient packets in the syn queue to warrant starting drops. Increment the
appropriate counters so this isn't silent, for accurate stats and help in
debugging.

This patch assumes LINUX_MIB_LISTENDROPS is a superset of/includes the
counter LINUX_MIB_LISTENOVERFLOWS.
Signed-off-by: Nivedita Singhvi <niv@us.ibm.com>
Acked-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The "Universal/Local" (U/L) bit must be complmented according to RFC4944
and RFC2464.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We forbid polling, writing and reading when the file were detached, this may
complex the user in several cases:

- when guest pass some buffers to vhost/qemu and then disable some queues,
  host/qemu needs to do its own cleanup on those buffers which is complex
  sometimes. We can do this simply by allowing a user can still write to an
  disabled queue. Write to an disabled queue will cause the packet pass to the
  kernel and read will get nothing.
- align the polling behavior with macvtap which never fails when the queue is
  created. This can simplify the polling errors handling of its user (e.g vhost)

We can simply achieve this by don't assign NULL to tfile->tun when detached.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the polling errors were ignored, which can lead following issues:

- vhost remove itself unconditionally from waitqueue when stopping the poll,
  this may crash the kernel since the previous attempt of starting may fail to
  add itself to the waitqueue
- userspace may think the backend were successfully set even when the polling
  failed.

Solve this by:

- check poll->wqh before trying to remove from waitqueue
- report polling errors in vhost_poll_start(), tx_poll_start(), the return value
  will be checked and returned when userspace want to set the backend

After this fix, there still could be a polling failure after backend is set, it
will addressed by the next patch.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, when vhost_init_used() fails the sock refcnt and ubufs were
leaked. Correct this by calling vhost_init_used() before assign ubufs and
restore the oldsock when it fails.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit c8d68e6b removed carrier off call
from tun_detach since it's now called on queue disable and not only on
tun close.  This confuses userspace which used this flag to detect a
free tun. To fix, put this back but under if (clean).
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Jason Wang <jasowang@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Tested-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The return value of pktgen_add_device() is not checked, so
even if we fail to add some device, for example, non-exist one,
we still see "OK:...". This patch fixes it.

After this patch, I got:

	# echo "add_device non-exist" > /proc/net/pktgen/kpktgend_0
	-bash: echo: write error: No such device
	# cat /proc/net/pktgen/kpktgend_0
	Running:
	Stopped:
	Result: ERROR: can not add device non-exist
	# echo "add_device eth0" > /proc/net/pktgen/kpktgend_0
	# cat /proc/net/pktgen/kpktgend_0
	Running:
	Stopped: eth0
	Result: OK: add_device=eth0

(Candidate for -stable)

Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The delay calculation with the rate extension introduces in v3.3 does
not properly work, if other packets are still queued for transmission.
For the delay calculation to work, both delay types (latency and delay
introduces by rate limitation) have to be handled differently. The
latency delay for a packet can overlap with the delay of other packets.
The delay introduced by the rate however is separate, and can only
start, once all other rate-introduced delays finished.

Latency delay is from same distribution for each packet, rate delay
depends on the packet size.

.: latency delay
-: rate delay
x: additional delay we have to wait since another packet is currently
   transmitted

  .....----                    Packet 1
    .....xx------              Packet 2
               .....------     Packet 3
    ^^^^^
    latency stacks
         ^^
         rate delay doesn't stack
               ^^
               latency stacks

  -----> time

When a packet is enqueued, we first consider the latency delay. If other
packets are already queued, we can reduce the latency delay until the
last packet in the queue is send, however the latency delay cannot be
<0, since this would mean that the rate is overcommitted.  The new
reference point is the time at which the last packet will be send. To
find the time, when the packet should be send, the rate introduces delay
has to be added on top of that.
Signed-off-by: Johannes Naab <jn@stusta.de>
Acked-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a tunnel socket is created by userspace, l2tp hooks the socket destructor
in order to clean up resources if userspace closes the socket or crashes.  It
also caches a pointer to the struct sock for use in the data path and in the
netlink interface.

While it is safe to use the cached sock pointer in the data path, where the
skb references keep the socket alive, it is not safe to use it elsewhere as
such access introduces a race with userspace closing the socket.  In
particular, l2tp_tunnel_delete is prone to oopsing if a multithreaded
userspace application closes a socket at the same time as sending a netlink
delete command for the tunnel.

This patch fixes this oops by forcing l2tp_tunnel_delete to explicitly look up
a tunnel socket held by userspace using sockfd_lookup().
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull powerpc fixes from Benjamin Herrenschmidt:
 "Whenever you have a chance between two dives, you might want to
  consider pulling my merge branch to pickup a few fixes for 3.8 that
  have been accumulating for the last couple of weeks (I was myself
  travelling then on vacation).

  Nothing major, just a handful of powerpc bug fixes that I consider
  worth getting in before 3.8 goes final."

And I'll have everybody know that I'm not diving for several days yet.
Snif.

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc: Max next_tb to prevent from replaying timer interrupt
  powerpc: kernel/kgdb.c: Fix memory leakage
  powerpc/book3e: Disable interrupt after preempt_schedule_irq
  powerpc/oprofile: Fix error in oprofile power7_marked_instr_event() function
  powerpc/pasemi: Fix crash on reboot
  powerpc: Fix MAX_STACK_TRACE_ENTRIES too low warning for ppc32

With lazy interrupt, we always call __check_irq_replaysome with
decrementers_next_tb to check if we need to replay timer interrupt.
So in hotplug case we also need to set decrementers_next_tb as MAX
to make sure __check_irq_replay don't replay timer interrupt
when return as we expect, otherwise we'll trap here infinitely.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

the variable backup_current_thread_info isn't freed before existing the
function.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

In preempt case current arch_local_irq_restore() from
preempt_schedule_irq() may enable hard interrupt but we really
should disable interrupts when we return from the interrupt,
and so that we don't get interrupted after loading SRR0/1.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The calculation for the left shift of the mask OPROFILE_PM_PMCSEL_MSK has an
error.  The calculation is should be to shift left by (max_cntrs - cntr) times
the width of the pmsel field width.  However, the #define OPROFILE_MAX_PMC_NUM
was used instead of OPROFILE_PMSEL_FIELD_WIDTH.  This patch fixes the
calculation.
Signed-off-by: Carl Love <cel@us.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

commit f96972f2 "kernel/sys.c: call disable_nonboot_cpus() in
kernel_restart()"

added a call to disable_nonboot_cpus() on kernel_restart(), which tries
to shutdown all the CPUs except the first one. The issue with the PA
Semi, is that it does not support CPU hotplug.

When the call is made to __cpu_down(), it calls the notifiers
CPU_DOWN_PREPARE, and then tries to take the CPU down.

One of the notifiers to the CPU hotplug code, is the cpufreq. The
DOWN_PREPARE will call __cpufreq_remove_dev() which calls
cpufreq_driver->exit. The PA Semi exit handler unmaps regions of I/O
that is used by an interrupt that goes off constantly
(system_reset_common, but it goes off during normal system operations
too). I'm not sure exactly what this interrupt does.

Running a simple function trace, you can see it goes off quite a bit:

# tracer: function
#
#           TASK-PID    CPU#    TIMESTAMP  FUNCTION
#              | |       |          |         |
          <idle>-0     [001]  1558.859363: .pasemi_system_reset_exception <-.system_reset_exception
          <idle>-0     [000]  1558.860112: .pasemi_system_reset_exception <-.system_reset_exception
          <idle>-0     [000]  1558.861109: .pasemi_system_reset_exception <-.system_reset_exception
          <idle>-0     [001]  1558.861361: .pasemi_system_reset_exception <-.system_reset_exception
          <idle>-0     [000]  1558.861437: .pasemi_system_reset_exception <-.system_reset_exception

When the region is unmapped, the system crashes with:

Disabling non-boot CPUs ...
Error taking CPU1 down: -38
Unable to handle kernel paging request for data at address 0xd0000800903a0100
Faulting instruction address: 0xc000000000055fcc
Oops: Kernel access of bad area, sig: 11 [#1]
PREEMPT SMP NR_CPUS=64 NUMA PA Semi PWRficient
Modules linked in: shpchp
NIP: c000000000055fcc LR: c000000000055fb4 CTR: c0000000000df1fc
REGS: c0000000012175d0 TRAP: 0300   Not tainted  (3.8.0-rc4-test-dirty)
MSR: 9000000000009032 <SF,HV,EE,ME,IR,DR,RI>  CR: 24000088  XER: 00000000
SOFTE: 0
DAR: d0000800903a0100, DSISR: 42000000
TASK = c0000000010e9008[0] 'swapper/0' THREAD: c000000001214000 CPU: 0
GPR00: d0000800903a0000 c000000001217850 c0000000012167e0 0000000000000000
GPR04: 0000000000000000 0000000000000724 0000000000000724 0000000000000000
GPR08: 0000000000000000 0000000000000000 0000000000000001 0000000000a70000
GPR12: 0000000024000080 c00000000fff0000 ffffffffffffffff 000000003ffffae0
GPR16: ffffffffffffffff 0000000000a21198 0000000000000060 0000000000000000
GPR20: 00000000008fdd35 0000000000a21258 000000003ffffaf0 0000000000000417
GPR24: 0000000000a226d0 c000000000000000 0000000000000000 0000000000000000
GPR28: c00000000138b358 0000000000000000 c000000001144818 d0000800903a0100
NIP [c000000000055fcc] .set_astate+0x5c/0xa4
LR [c000000000055fb4] .set_astate+0x44/0xa4
Call Trace:
[c000000001217850] [c000000000055fb4] .set_astate+0x44/0xa4 (unreliable)
[c0000000012178f0] [c00000000005647c] .restore_astate+0x2c/0x34
[c000000001217980] [c000000000054668] .pasemi_system_reset_exception+0x6c/0x88
[c000000001217a00] [c000000000019ef0] .system_reset_exception+0x48/0x84
[c000000001217a80] [c000000000001e40] system_reset_common+0x140/0x180
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Pull dmraid fix from NeilBrown:
 "Just one fix for md in 3.8

  dmraid assess redundancy and replacements slightly inaccurately which
  could lead to some degraded arrays failing to assemble."

* tag 'md-3.8-fixes' of git://neil.brown.name/md:
  DM-RAID: Fix RAID10's check for sufficient redundancy

This patch fixes MAX_STACK_TRACE_ENTRIES too low warning for ppc32,
which is similar to commit 12660b17.
Reported-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Tested-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Pull GFS2 fix from Steven Whitehouse.

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
  GFS2: fix skip unlock condition

Pull IOMMU fix from Joerg Roedel:
 "One fix for the AMD IOMMU driver to work around broken BIOSes found in
  the field.  Some BIOSes forget to enable a workaround for a hardware
  problem which might cause the IOMMU to stop working under high load
  conditions.  The fix makes sure this workaround is enabled."

* tag 'iommu-fixes-v3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  IOMMU, AMD Family15h Model10-1Fh erratum 746 Workaround

Pull MFD fixes from Samuel Ortiz:
 "This is the first pull request for MFD fixes for 3.8

  We have some build failure fixes (twl4030, vexpress, abx500 and
  tps65910), some actual runtime oops and lockup fixes (rtsx, da9052),
  and some more hypothetical NULL pointers dereferences fixes for
  pcf50633 and max776xx.

  Then we also have additional rtsx fixes for a correct switch output
  voltage and clock divider correctness for rtl8411 (rtsx driver), and
  irqdomain fix for db8550-prcmu, and some more cosmetic fixes for
  arizona and wm5102."

* tag 'mfd-for-linus-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
  mfd: rtsx: Fix oops when rtsx_pci_sdmmc is not probed
  mfd: wm5102: Fix definition of WM5102_MAX_REGISTER
  mfd: twl4030: Don't warn about uninitialized return code
  mfd: da9052/53 lockup fix
  mfd: rtsx: Add clock divider hook
  mmc: rtsx: Call MFD hook to switch output voltage
  mfd: rtsx: Add output voltage switch hook
  mfd: Fix compile errors and warnings when !CONFIG_AB8500_BM
  mfd: vexpress: Export global functions to fix build error
  mfd: arizona: Check errors from regcache_sync()
  mfd: tc3589x: Use simple irqdomain
  mfd: pcf50633: Init pcf->dev before using it
  mfd: max77693: Init max77693->dev before using it
  mfd: max77686: Init max77686->dev before using it
  mfd: db8500-prcmu: Fix irqdomain usage
  mfd: tps65910: Select REGMAP_IRQ in Kconfig to fix build error
  mfd: arizona: Disable control interface reporting for WM5102 and WM5110

Pull networking updates from David Miller:
 "Much more accumulated than I would have liked due to an unexpected
  bout with a nasty flu:

   1) AH and ESP input don't set ECN field correctly because the
      transport head of the SKB isn't set correctly, fix from Li
      RongQing.

   2) If netfilter conntrack zones are disabled, we can return an
      uninitialized variable instead of the proper error code.  Fix from
      Borislav Petkov.

   3) Fix double SKB free in ath9k driver beacon handling, from Felix
      Feitkau.

   4) Remove bogus assumption about netns cleanup ordering in
      nf_conntrack, from Pablo Neira Ayuso.

   5) Remove a bogus BUG_ON in the new TCP fastopen code, from Eric
      Dumazet.  It uses spin_is_locked() in it's test and is therefore
      unsuitable for UP.

   6) Fix SELINUX labelling regressions added by the tuntap multiqueue
      changes, from Paul Moore.

   7) Fix CRC errors with jumbo frame receive in tg3 driver, from Nithin
      Nayak Sujir.

   8) CXGB4 driver sets interrupt coalescing parameters only on first
      queue, rather than all of them.  Fix from Thadeu Lima de Souza
      Cascardo.

   9) Fix regression in the dispatch of read/write registers in dm9601
      driver, from Tushar Behera.

  10) ipv6_append_data miscalculates header length, from Romain KUNTZ.

  11) Fix PMTU handling regressions on ipv4 routes, from Steffen
      Klassert, Timo Teräs, and Julian Anastasov.

  12) In 3c574_cs driver, add necessary parenthesis to "x << y & z"
      expression.  From Nickolai Zeldovich.

  13) macvlan_get_size() causes underallocation netlink message space,
      fix from Eric Dumazet.

  14) Avoid division by zero in xfrm_replay_advance_bmp(), from Nickolai
      Zeldovich.  Amusingly the zero check was already there, we were
      just performing it after the modulus :-)

  15) Some more splice bug fixes from Eric Dumazet, which fix things
      mostly eminating from how we now more aggressively use high-order
      pages in SKBs.

  16) Fix size calculation bug when freeing hash tables in the IPSEC
      xfrm code, from Michal Kubecek.

  17) Fix PMTU event propagation into socket cached routes, from Steffen
      Klassert.

  18) Fix off by one in TX buffer release in netxen driver, from Eric
      Dumazet.

  19) Fix rediculous memory allocation requirements introduced by the
      tuntap multiqueue changes, from Jason Wang.

  20) Remove bogus AMD platform workaround in r8169 driver that causes
      major problems in normal operation, from Timo Teräs.

  21) virtio-net set affinity and select queue don't handle
      discontiguous cpu numbers properly, fix from Wanlong Gao.

  22) Fix a route refcounting issue in loopback driver, from Eric
      Dumazet.  There's a similar fix coming that we might add to the
      macvlan driver as well.

  23) Fix SKB leaks in batman-adv's distributed arp table code, from
      Matthias Schiffer.

  24) r8169 driver gives descriptor ownership back the hardware before
      we're done reading the VLAN tag out of it, fix from Francois
      Romieu.

  25) Checksums not calculated properly in GRE tunnel driver fix from
      Pravin B Shelar.

26) Fix SCTP memory leak on namespace exit."

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (101 commits)
  dm9601: support dm9620 variant
  SCTP: Free the per-net sysctl table on net exit. v2
  net: phy: icplus: fix broken INTR pin settings
  net: phy: icplus: Use the RGMII interface mode to configure clock delays
  IP_GRE: Fix kernel panic in IP_GRE with GRE csum.
  sctp: set association state to established in dupcook_a handler
  ip6mr: limit IPv6 MRT_TABLE identifiers
  r8169: fix vlan tag read ordering.
  net: cdc_ncm: use IAD provided by the USB core
  batman-adv: filter ARP packets with invalid MAC addresses in DAT
  batman-adv: check for more types of invalid IP addresses in DAT
  batman-adv: fix skb leak in batadv_dat_snoop_incoming_arp_reply()
  net: loopback: fix a dst refcounting issue
  virtio-net: reset virtqueue affinity when doing cpu hotplug
  virtio-net: split out clean affinity function
  virtio-net: fix the set affinity bug when CPU IDs are not consecutive
  can: pch_can: fix invalid error codes
  can: ti_hecc: fix invalid error codes
  can: c_can: fix invalid error codes
  r8169: remove the obsolete and incorrect AMD workaround
  ...

The IOMMU may stop processing page translations due to a perceived lack
of credits for writing upstream peripheral page service request (PPR)
or event logs. If the L2B miscellaneous clock gating feature is enabled
the IOMMU does not properly register credits after the log request has
completed, leading to a potential system hang.

BIOSes are supposed to disable L2B micellaneous clock gating by setting
L2_L2B_CK_GATE_CONTROL[CKGateL2BMiscDisable](D0F2xF4_x90[2]) = 1b. This
patch corrects that for those which do not enable this workaround.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joro@8bytes.org>

The recent commit fb6791d1
included the wrong logic.  The lvbptr check was incorrectly
added after the patch was tested.
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

dm9620 is a newer variant of dm9601 with more features (usb 2.0, checksum
offload, ..), but it can also be put in a dm9601 compatible mode, allowing
us to reuse the existing driver.

This does mean that the extended features like checksum offload cannot be
used, but that's hardly critical on a 100mbps interface.

Thanks to Sławek Wernikowski <slawek@wernikowski.net> for providing me
with a dm9620 based device to test.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Per-net sysctl table needs to be explicitly freed at
net exit.  Otherwise we see the following with kmemleak:

unreferenced object 0xffff880402d08000 (size 2048):
  comm "chrome_sandbox", pid 18437, jiffies 4310887172 (age 9097.630s)
  hex dump (first 32 bytes):
    b2 68 89 81 ff ff ff ff 20 04 04 f8 01 88 ff ff  .h...... .......
    04 00 00 00 a4 01 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff815b4aad>] kmemleak_alloc+0x21/0x3e
    [<ffffffff81110352>] slab_post_alloc_hook+0x28/0x2a
    [<ffffffff81113fad>] __kmalloc_track_caller+0xf1/0x104
    [<ffffffff810f10c2>] kmemdup+0x1b/0x30
    [<ffffffff81571e9f>] sctp_sysctl_net_register+0x1f/0x72
    [<ffffffff8155d305>] sctp_net_init+0x100/0x39f
    [<ffffffff814ad53c>] ops_init+0xc6/0xf5
    [<ffffffff814ad5b7>] setup_net+0x4c/0xd0
    [<ffffffff814ada5e>] copy_net_ns+0x6d/0xd6
    [<ffffffff810938b1>] create_new_namespaces+0xd7/0x147
    [<ffffffff810939f4>] copy_namespaces+0x63/0x99
    [<ffffffff81076733>] copy_process+0xa65/0x1233
    [<ffffffff81077030>] do_fork+0x10b/0x271
    [<ffffffff8100a0e9>] sys_clone+0x23/0x25
    [<ffffffff815dda73>] stub_clone+0x13/0x20
    [<ffffffffffffffff>] 0xffffffffffffffff

I fixed the spelling of sysctl_header so the code actually
compiles. -- EWB.
Reported-by: Martin Mokrejs <mmokrejs@fold.natur.cuni.cz>
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the setting of the INTR pin that is
valid for IP101 A/G device and not for the IP1001.
Reported-by: Anunay Saxena <anunay.saxena@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Like several other PHY devices which support RGMII, the IC+1001 allows
additional delays to by added to the RX_CLK and TX_CLK signals to
compensate for skew between the clock and data signals. Previously this
was always enabled, but this change makes use of the different RGMII
interface modes to allow the user to specify whether this should be
enabled.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Due to IP_GRE GSO support, GRE can recieve non linear skb which
results in panic in case of GRE_CSUM.  Following patch fixes it by
using correct csum API.

Bug introduced in commit 6b78f16e (gre: add GSO support)
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While sctp handling a duplicate COOKIE-ECHO and the action is
'Association restart', sctp_sf_do_dupcook_a() will processing
the unexpected COOKIE-ECHO for peer restart, but it does not set
the association state to SCTP_STATE_ESTABLISHED, so the association
could stuck in SCTP_STATE_SHUTDOWN_PENDING state forever.
This violates the sctp specification:
  RFC 4960 5.2.4. Handle a COOKIE ECHO when a TCB Exists
  Action
  A) In this case, the peer may have restarted. .....
     After this, the endpoint shall enter the ESTABLISHED state.

To resolve this problem, adding a SCTP_CMD_NEW_STATE cmd to the
command list before SCTP_CMD_REPLY cmd, this will set the restart
association to SCTP_STATE_ESTABLISHED state properly and also avoid
I-bit being set in the DATA chunk header when COOKIE_ACK is bundled
with DATA chunks.
Signed-off-by: Xufeng Zhang <xufeng.zhang@windriver.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We did this for IPv4 in b49d3c1e "net: ipmr: limit MRT_TABLE
identifiers" but we need to do it for IPv6 as well.  On IPv6 the name
is "pim6reg" instead of "pimreg" so there is one less digit allowed.

The strcpy() is in ip6mr_reg_vif().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Control of receive descriptor must not be returned to ethernet chipset
before vlan tag processing is done.

VLAN tag receive word is now reset both in normal and error path.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Spotted-by: Timo Teras <timo.teras@iki.fi>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>