Some of the interrupt vectors on 64-bit POWER server processors are only
32 bytes long (8 instructions), which is not enough for the full
first-level interrupt handler. For these we need to branch to an
out-of-line (OOL) handler. But when we are running a relocatable kernel,
interrupt vectors till __end_interrupts marker are copied down to real
address 0x100. So, branching to labels (ie. OOL handlers) outside this
section must be handled differently (see LOAD_HANDLER()), considering
relocatable kernel, which would need at least 4 instructions.

However, branching from interrupt vector means that we corrupt the
CFAR (come-from address register) on POWER7 and later processors as
mentioned in commit 1707dd16. So, EXCEPTION_PROLOG_0 (6 instructions)
that contains the part up to the point where the CFAR is saved in the
PACA should be part of the short interrupt vectors before we branch out
to OOL handlers.

But as mentioned already, there are interrupt vectors on 64-bit POWER
server processors that are only 32 bytes long (like vectors 0x4f00,
0x4f20, etc.), which cannot accomodate the above two cases at the same
time owing to space constraint. Currently, in these interrupt vectors,
we simply branch out to OOL handlers, without using LOAD_HANDLER(),
which leaves us vulnerable when running a relocatable kernel (eg. kdump
case). While this has been the case for sometime now and kdump is used
widely, we were fortunate not to see any problems so far, for three
reasons:

  1. In almost all cases, production kernel (relocatable) is used for
     kdump as well, which would mean that crashed kernel's OOL handler
     would be at the same place where we end up branching to, from short
     interrupt vector of kdump kernel.
  2. Also, OOL handler was unlikely the reason for crash in almost all
     the kdump scenarios, which meant we had a sane OOL handler from
     crashed kernel that we branched to.
  3. On most 64-bit POWER server processors, page size is large enough
     that marking interrupt vector code as executable (see commit
     429d2e83) leads to marking OOL handler code from crashed kernel,
     that sits right below interrupt vector code from kdump kernel, as
     executable as well.

Let us fix this by moving the __end_interrupts marker down past OOL
handlers to make sure that we also copy OOL handlers to real address
0x100 when running a relocatable kernel.

This fix has been tested successfully in kdump scenario, on an LPAR with
4K page size by using different default/production kernel and kdump
kernel.

Also tested by manually corrupting the OOL handlers in the first kernel
and then kdump'ing, and then causing the OOL handlers to fire - mpe.

Fixes: c1fb6816 ("powerpc: Add relocation on exception vector handlers")
Cc: stable@vger.kernel.org
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Merge the support for live patching on ppc64le using mprofile-kernel.
This branch has also been merged into the livepatching tree for v4.7.

Add the kconfig logic & assembly support for handling live patched
functions. This depends on DYNAMIC_FTRACE_WITH_REGS, which in turn
depends on the new -mprofile-kernel ftrace ABI, which is only supported
currently on ppc64le.

Live patching is handled by a special ftrace handler. This means it runs
from ftrace_caller(). The live patch handler modifies the NIP so as to
redirect the return from ftrace_caller() to the new patched function.

However there is one particularly tricky case we need to handle.

If a function A calls another function B, and it is known at link time
that they share the same TOC, then A will not save or restore its TOC,
and will call the local entry point of B.

When we live patch B, we replace it with a new function C, which may
not have the same TOC as A. At live patch time it's too late to modify A
to do the TOC save/restore, so the live patching code must interpose
itself between A and C, and do the TOC save/restore that A omitted.

An additionaly complication is that the livepatch code can not create a
stack frame in order to save the TOC. That is because if C takes > 8
arguments, or is varargs, A will have written the arguments for C in
A's stack frame.

To solve this, we introduce a "livepatch stack" which grows upward from
the base of the regular stack, and is used to store the TOC & LR when
calling a live patched function.

When the patched function returns, we retrieve the real LR & TOC from
the livepatch stack, restore them, and pop the livepatch "stack frame".
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>

In order to support live patching we need to maintain an alternate
stack of TOC & LR values. We use the base of the stack for this, and
store the "live patch stack pointer" in struct thread_info.

Unlike the other fields of thread_info, we can not statically initialise
that value, so it must be done at run time.

This patch just adds the code to support that, it is not enabled until
the next patch which actually adds live patch support.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Balbir Singh <bsingharora@gmail.com>

Add the powerpc specific livepatch definitions. In particular we provide
a non-default implementation of klp_get_ftrace_location().

This is required because the location of the mcount call is not constant
when using -mprofile-kernel (which we always do for live patching).
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

When livepatch tries to patch a function it takes the function address
and asks ftrace to install the livepatch handler at that location.
ftrace will look for an mcount call site at that exact address.

On powerpc the mcount location is not the first instruction of the
function, and in fact it's not at a constant offset from the start of
the function. To accommodate this add a hook which arch code can
override to customise the behaviour.
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

In order to support live patching on powerpc we would like to call
ftrace_location_range(), so make it global.
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Fix bogus memsets pointed out by sparse:

linux-v4.3/drivers/macintosh/rack-meter.c:157:15: warning: memset with byte count of 0
linux-v4.3/drivers/macintosh/rack-meter.c:158:15: warning: memset with byte count of 0

Probably "&" is mistyped "*"; use ARRAY_SIZE to make it more safe.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Limit idle ticks to total ticks. This prevents the annoying rackmeter
leds fully ON / OFF blinking state that happens on fully idling
G5 Xserve systems.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Sometimes when sparse warns about undefined symbols, it isn't
because they should have 'static' added, it's because they're
overriding __weak symbols defined elsewhere, and the header has
been missed.

Fix a few of them by adding appropriate headers.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

As sparse suggests, these should be made static.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The POWER8NVL chip has two CAPI ports.  Configure the PSL to route
data to the port corresponding to the CAPP unit.
Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This patch assigns numbers to OPAL_MSG macros of enum opal_msg_type
to prevent accidental insertion of any new value in between and thus
break OPAL API. This is also helpful while backporting mainline kernel
changes to distros which run downlevel kernel and thus don't have all
OPAL messages defined, avoiding unnecessary bugs due to enum values
order mismatch.
Signed-off-by: Vipin K Parashar <vipin@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We'd like folks working on drivers for powerpc to also Cc linuxppc-dev,
so we can be aware of what's going on in drivers and/or review the
changes.

So add patterns to the powerpc MAINTAINERS section to catch some of the
drivers we're interested in.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

If CONFIG_HIBERNATION and CONFIG_PPC_BOOK3S_64 are set, code in
arch/powerpc/kernel/swsusp_amd64.S which uses the tlbia macro is enabled.
tlbia in turn uses tlbie, an instruction which takes more than one
operand in newer versions of POWER.  As such, the kernel fails to build
due to the assembler complaining about missing operands.

This can be worked around by assembling the instruction as in POWER4.
This fixes the build breakage caused by enabling CONFIG_HIBERNATION.
Hibernation is currently only tested on G5 PowerMacs, which should be
unaffected by this change.  For other platforms it may now build,
whether or not it works is a different story.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Currently on PPC64 changing kernel pagesize from 4K to 64K leaves
FORCE_MAX_ZONEORDER set to 13 - which produces a compile error.

The error occurs because of the following constraint (from
include/linux/mmzone.h) being violated:

	MAX_ORDER -1 + PAGESHIFT <= SECTION_SIZE_BITS.

Expanding this out, we get:

	FORCE_MAX_ZONEBITS <= 25 - PAGESHIFT,

which requires, for a 64K page, FORCE_MAX_ZONEBITS <= 9. Thus set max
value of FORCE_MAX_ZONEORDER for 64K pages to 9, and 4K pages to 13.

Also, check the minimum value:
In include/linux/huge_mm.h, we have the constraint HPAGE_PMD_ORDER <
MAX_ORDER which expands out to:

	PTE_INDEX_SIZE < FORCE_MAX_ZONEORDER.

PTE_INDEX_SIZE is:
	9 (4k hash or no hash 4K pgtable) or
	8 (64K hash or no hash 64K pgtable).
Thus a min value of 8 for 64K pages and 9 for 4K pages is reasonable.

So, update the range of FORCE_MAX_ZONEORDER from 9-64 to 8-9 for 64K pages
and from 13-64 to 9-13 for 4K pages.
Signed-off-by: Rashmica Gupta <rashmicy@gmail.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The Kconfig for this driver is currently:

config CPU_FREQ_CBE_PMI
    bool "CBE frequency scaling using PMI interface"

...meaning that it currently is not being built as a module by
anyone.  Lets remove the modular and unused code here, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Christian Krafft <krafft@de.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-pm@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The Makefile/Kconfig currently controlling compilation of this code is:

obj-$(CONFIG_PPC64)             += setup_64.o sys_ppc32.o \
                                   signal_64.o ptrace32.o \
                                   paca.o nvram_64.o firmware.o

arch/powerpc/platforms/Kconfig.cputype:config PPC64
arch/powerpc/platforms/Kconfig.cputype: bool "64-bit kernel"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.

We don't replace module.h with init.h since the file already has that.

We delete the MODULE_LICENSE tag since that information is already
contained at the top of the file in the comments.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Hari Bathini <hbathini@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The Kconfig currently controlling compilation of this code is:

arch/powerpc/platforms/cell/Kconfig:config SPU_BASE
arch/powerpc/platforms/cell/Kconfig:    bool

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

IBM online documentation for EEH uses "extended error handling" and
"enhanced error handling" to refer to the same thing, in different
places.  The only place mentioning it as "enhanced error handling" in the
kernel is the MAINTAINERS file, and it's "extended" in some documentation.

IBM originally defined EEH as "enhanced error handling", so standardise
all mentions of EEH to use that term.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

generic_memcpy() is only called from copy_32.S, so there's no reason for
it to be global.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This has been unused since ~2004, remove it.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We have a bunch of SLB related code in the tree which is there to handle
dynamic VSIDs - but currently it's all disabled at compile time. The
comments say "Keep that around for when we re-implement dynamic VSIDs".

But that was over 10 years ago (commit 3c726f8d ("[PATCH] ppc64:
support 64k pages")). The chance that it would still work unchanged is
minimal, and in the meantime it's confusing to folks browsing/grepping
the code. If we ever want to re-instate it, it's in the git history.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Balbir Singh <bsingharora@gmail.com>

The HMI code knows about three types of errors: CORE, NX and UNKNOWN.
If OPAL were to add a new type, it would not be handled at all since
there is no fallback case.  Instead of explicitly checking for UNKNOWN,
treat any checkstop type without a handler as unknown.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Function cxl_get_phys_dev() was removed from the kernel API by a
previous patch, but it's actually dead code. Remove it.
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The associativity array index specified for a LMB in the device tree,
/ibm,dynamic-reconfiguration-memory/ibm,dynamic-memory, needs to be updated
prior to DLPAR adding a LMB and after DLPAR removing a LMB.

Without doing this step in the DLPAR add process a LMB could be configured
with the incorrect affinity. For a LMB that was not present at boot the
affinity index is set to 0xffffffff, which defaults to adding the LMB to
the first online node since the index is not a valid value. Or, the
affinity index could contain a stale value if the LMB was present at boot
but later DLPAR removed and is being DLPAR added back to the system.

This patch adds a step in the DLPAR add flow to look up the associativity
index for a LMB prior to adding a LMB and setting the associativity to
0xffffffff when a LMB is removed.

This patch also modifies the DLPAR add/remove flow to no longer do a single
update of the device tree property after all of the requested DLPAR
operations are complete and now does a property update during the add
or remove of each LMB.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Re-factor dlpar_lmb_add() routine by moving the validation of the lmb
flags and the acquireing of the DRC to a wrapper around the work to add
the memory to the system. This is done to make handling of errors
during the addition of the memory easier and to facilitate the upcoming
addition of updating the lmb's affinity prior to adding the memory.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Pull ARM fixes from Russell King:
 "A couple of small fixes, and wiring up the new syscalls which appeared
  during the merge window"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8550/1: protect idiv patching against undefined gcc behavior
  ARM: wire up preadv2 and pwritev2 syscalls
  ARM: SMP enable of cache maintanence broadcast

Pull MMC fixes from Ulf Hansson:
 "Here are a couple of mmc fixes intended for v4.6 rc3:

  MMC host:
   - sdhci: Fix regression setting power on Trats2 board
   - sdhci-pci: Add support and PCI IDs for more Broxton host controllers"

* tag 'mmc-v4.6-rc1' of git://git.linaro.org/people/ulf.hansson/mmc:
  mmc: sdhci-pci: Add support and PCI IDs for more Broxton host controllers
  mmc: sdhci: Fix regression setting power on Trats2 board

Pull i2c fixes from Wolfram Sang:
 "Some bugfixes from I2C:

   - fix a uevent triggered boot problem by removing a useless debug
     print

   - fix sysfs-attributes of the new i2c-demux-pinctrl driver to follow
     standard kernel behaviour

   - fix a potential division-by-zero error (needed two takes)"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: jz4780: really prevent potential division by zero
  Revert "i2c: jz4780: prevent potential division by zero"
  i2c: jz4780: prevent potential division by zero
  i2c: mux: demux-pinctrl: Update docs to new sysfs-attributes
  i2c: mux: demux-pinctrl: Clean up sysfs attributes
  i2c: prevent endless uevent loop with CONFIG_I2C_DEBUG_CORE

This reverts commit 1028b55b.

It's broken: it makes ext4 return an error at an invalid point, causing
the readdir wrappers to write the the position of the last successful
directory entry into the position field, which means that the next
readdir will now return that last successful entry _again_.

You can only return fatal errors (that terminate the readdir directory
walk) from within the filesystem readdir functions, the "normal" errors
(that happen when the readdir buffer fills up, for example) happen in
the iterorator where we know the position of the actual failing entry.

I do have a very different patch that does the "signal_pending()"
handling inside the iterator function where it is allowable, but while
that one passes all the sanity checks, I screwed up something like four
times while emailing it out, so I'm not going to commit it today.

So my track record is not good enough, and the stars will have to align
better before that one gets committed.  And it would be good to get some
review too, of course, since celestial alignments are always an iffy
debugging model.

IOW, let's just revert the commit that caused the problem for now.
Reported-by: Greg Thelen <gthelen@google.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull parisc fixes from Helge Deller:
 "Since commit 0de79858 ("parisc: Use generic extable search and
  sort routines") module loading is boken on parisc, because the parisc
  module loader wasn't prepared for the new R_PARISC_PCREL32 relocations.

  In addition, due to that breakage, Mikulas Patocka noticed that
  handling exceptions from modules probably never worked on parisc.  It
  was just masked by the fact that exceptions from modules don't happen
  during normal use.

  This patch series fixes those issues and survives the tests of the
  lib/test_user_copy kernel module test.  Some patches are tagged for
  stable"

* 'parisc-4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Update comment regarding relative extable support
  parisc: Unbreak handling exceptions from kernel modules
  parisc: Fix kernel crash with reversed copy_from_user()
  parisc: Avoid function pointers for kernel exception routines
  parisc: Handle R_PARISC_PCREL32 relocations in kernel modules

Pull libnvdimm fixes from Dan Williams:
 "Three fixes, the first two are tagged for -stable:

   - The ndctl utility/library gained expanded unit tests illuminating a
     long standing bug in the libnvdimm SMART data retrieval
     implementation.

     It has been broken since its initial implementation, now fixed.

   - Another one line fix for the detection of stale info blocks.

     Without this change userspace can get into a situation where it is
     unable to reconfigure a namespace.

   - Fix the badblock initialization path in the presence of the new (in
     v4.6-rc1) section alignment workarounds.

     Without this change badblocks will be reported at the wrong offset.

  These have received a build success report from the kbuild robot and
  have appeared in -next with no reported issues"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  libnvdimm, pfn: fix nvdimm_namespace_add_poison() vs section alignment
  libnvdimm, pfn: fix uuid validation
  libnvdimm: fix smart data retrieval

Pull GPIO fixes from Linus Walleij:
 "Here is a set of four GPIO fixes.  The two fixes to the core are
  serious as they are regressing minor architectures.

  Core fixes:

   - Defer GPIO device setup until after gpiolib is initialized.

     It turns out that a few very tightly integrated GPIO platform
     drivers initialize so early (befor core_initcall()) so that the
     gpiolib isn't even initialized itself.  That limits what the
     library can do, and we cannot reference uninitialized fields until
     later.

     Defer some of the initialization until right after the gpiolib is
     initialized in these (rare) cases.

   - As a consequence: do not use devm_* resources when allocating the
     states in the initial set-up of the gpiochip.

  Driver fixes:

   - In ACPI retrieveal: ignore GpioInt when looking for output GPIOs.

   - Fix legacy builds on the PXA without a backing pin controller.

   - Use correct datatype on pca953x register writes"

* tag 'gpio-v4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: pca953x: Use correct u16 value for register word write
  gpiolib: Defer gpio device setup until after gpiolib initialization
  gpiolib: Do not use devm functions when registering gpio chip
  gpio: pxa: fix legacy non pinctrl aware builds
  gpio / ACPI: ignore GpioInt() GPIOs when requesting GPIO_OUT_*

Pull tty fixes from Greg KH:
 "Here are two tty fixes for issues found.

  One was due to a merge error in 4.6-rc1, and the other a regression
  fix for UML consoles that broke in 4.6-rc1.

  Both have been in linux-next for a while"

* tag 'tty-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: Fix merge of "tty: Refactor tty_open()"
  tty: Fix UML console breakage

Pull USB fixes from Greg KH:
 "Here are some USB fixes and new device ids for 4.6-rc3.

  Nothing major, the normal USB gadget fixes and usb-serial driver ids,
  along with some other fixes mixed in.  All except the USB serial ids
  have been tested in linux-next, the id additions should be fine as
  they are 'trivial'"

* tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
  USB: option: add "D-Link DWM-221 B1" device id
  USB: serial: cp210x: Adding GE Healthcare Device ID
  USB: serial: ftdi_sio: Add support for ICP DAS I-756xU devices
  usb: dwc3: keystone: drop dma_mask configuration
  usb: gadget: udc-core: remove manual dma configuration
  usb: dwc3: pci: add ID for one more Intel Broxton platform
  usb: renesas_usbhs: fix to avoid using a disabled ep in usbhsg_queue_done()
  usb: dwc2: do not override forced dr_mode in gadget setup
  usb: gadget: f_midi: unlock on error
  USB: digi_acceleport: do sanity checking for the number of ports
  USB: cypress_m8: add endpoint sanity check
  USB: mct_u232: add sanity checking in probe
  usb: fix regression in SuperSpeed endpoint descriptor parsing
  USB: usbip: fix potential out-of-bounds write
  usb: renesas_usbhs: disable TX IRQ before starting TX DMAC transfer
  usb: renesas_usbhs: avoid NULL pointer derefernce in usbhsf_pkt_handler()
  usb: gadget: f_midi: Fixed a bug when buflen was smaller than wMaxPacketSize
  usb: phy: qcom-8x16: fix regulator API abuse
  usb: ch9: Fix SSP Device Cap wFunctionalitySupport type
  usb: gadget: composite: Access SSP Dev Cap fields properly
  ...

Pull staging and IIO driver fixes from Greg KH:
 "Here are some IIO driver fixes, along with two staging driver fixes
  for 4.6-rc3.

  One staging driver patch reverts the deletion of a driver that
  happened in 4.6-rc1.  We thought that laptop.org was dead, but it's
  still alive and kicking, and has users that were mad we broke their
  hardware by deleting a driver for their machines.  So that driver is
  added back and everyone is happy again.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'staging-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  Revert "Staging: olpc_dcon: Remove obsolete driver"
  staging/rdma/hfi1: select CRC32
  iio: gyro: bmg160: fix buffer read values
  iio: gyro: bmg160: fix endianness when reading axes
  iio: accel: bmc150: fix endianness when reading axes
  iio: st_magn: always define ST_MAGN_TRIGGER_SET_STATE
  iio: fix config watermark initial value
  iio: health: max30100: correct FIFO check condition
  iio: imu: Fix inv_mpu6050 dependencies
  iio: adc: Fix build error of missing devm_ioremap_resource on UM
  iio: light: apds9960: correct FIFO check condition
  iio: adc: max1363: correct reference voltage
  iio: adc: max1363: add missing adc to max1363_id