- 15 Jun, 2019 36 commits
-
-
Yunsheng Lin authored
If hns3_nic_net_xmit does not return NETDEV_TX_BUSY when doing a loopback selftest, the skb is not freed in hns3_clean_tx_ring or hns3_nic_net_xmit, which causes skb not freed problem. This patch fixes it by freeing skb when hns3_nic_net_xmit does not return NETDEV_TX_OK. Fixes: c39c4d98 ("net: hns3: Add mac loopback selftest support in hns3 driver") Signed-off-by:
Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by:
Peng Li <lipeng321@huawei.com> Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Yunsheng Lin authored
The netdev is dereferenced before null checking in the function hns3_setup_tc. This patch moves the dereferencing after the null checking. Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by:
-
Yonglong Liu authored
In hns3_nic_init_irq(), if request irq fail at index i, the function return directly without releasing irq resources that already requested, and nowhere else will release them. Signed-off-by:
Yonglong Liu <liuyonglong@huawei.com> Signed-off-by:
-
Peng Li authored
IMP will set restting state for all function when PF FLR, driver just clear the restting state in resetting progress, but don't do it in initializing progress. As FLR is not created by driver, it is necessary to clear restting state when initializing HW device. Signed-off-by:
-
Weihang Li authored
Function hclge_handle_all_hw_msix_error() contains four parts: 1. Query buffer descriptors for MSI-X errors. 2. Query and clear all main PF MSI-X errors. 3. Query and clear all PF MSI-X errors. 4. Handle mac tunnel interrupts. Part 2 and part 3 handle errors of some different modules respectively, this patch extracts them into dividual functions, which makes the logic clearer. Signed-off-by:
Weihang Li <liweihang@hisilicon.com> Signed-off-by:
-
Weihang Li authored
This patch modifies print message of rx_q_search_miss from error to dfx to prevent misleading users, because this interrupt may occur if we receive packets during initialization of HNS3 driver. Otherwise, this patch masks 28th bit of PPU_MPF_ABNORMAL_SRC2 which is now meaningless. Signed-off-by:
-
Shiju Jose authored
This patch adds the recovery for the HNS H/W errors which occurred before the driver initialization. Reported-by:
Salil Mehta <salil.mehta@huawei.com> Signed-off-by:
Shiju Jose <shiju.jose@huawei.com> Signed-off-by:
-
Shiju Jose authored
Presently the HNS driver enables the HNS H/W error interrupts after the dev initialization is completed. However some exceptions such as NCSI errors can occur when the network port driver is not loaded and those errors required reporting to the BMC. Therefore the firmware enabled all the HNS ras error interrupts before the driver is loaded. And in some cases, there will be some H/W errors remained unclear before reboot. Thus the HNS driver needs to process and recover those hw errors occurred before HNS driver is initialized. This patch adds processing of the HNS hw errors(RAS and MSI-X) which occurred before the driver initialization. For RAS, because they are enabled by firmware, so we can detect specific bits, then log and clear them. But for MSI-X which can not be enabled before open vector0 irq, we can't detect the specific error bits, so we just write 1 to all interrupt source registers to clear. Signed-off-by:
-
Shiju Jose authored
HNS does not need to be reset when errors occur in some bits. However presently the HNAE3_FUNC_RESET is set in this case and as a result the default_reset is done when these errors are reported. This patch fix this issue. Also patch does some optimization in setting the reset level for the error recovery. Reported-by:
-
Shiju Jose authored
Presently the error handling code sets the reset level required for the recovery of the hw errors to the reset framework in the error_detected AER callback. However the rest_event would be called later from the slot_reset callback. This can cause issue of using the wrong reset_level if a high priority reset request occur before the slot_reset is called. This patch delays setting of the reset level, required for the hw errors, to the reset framework until the slot_reset is called. Reported-by:
-
David S. Miller authored
Michal Kalderon says: ==================== qed: iWARP fixes This series contains a few small fixes related to iWARP. ==================== Signed-off-by: -
Michal Kalderon authored
The default window size is calculated for best performance based on internal hw buffer sizes. The size differs between the different chips and modes. Fixes: 67b40dcc ("qed: Implement iWARP initialization, teardown and qp operations") Signed-off-by:
Ariel Elior <ariel.elior@marvell.com> Signed-off-by:
Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by:
-
Michal Kalderon authored
The driver needs to assign a lossless traffic class for the MPA ll2 connection to ensure no packets are dropped when returning from the driver as they will never be re-transmitted by the peer. Fixes: ae3488ff ("qed: Add ll2 connection for processing unaligned MPA packets") Signed-off-by:
-
Michal Kalderon authored
Fix uninitialized variable warning by static checker. Fixes: ae3488ff ("qed: Add ll2 connection for processing unaligned MPA packets") Signed-off-by:
-
Michal Kalderon authored
Destroy QP waits for it's ep object state to be set to CLOSED before proceeding. ep->state can be updated from a different context. Add smp_store_release/READ_ONCE to synchronize. Fixes: fc4c6065 ("qed: iWARP implement disconnect flows") Signed-off-by:
-
Dan Carpenter authored
The acpi_node_get_property_reference() doesn't return ACPI error codes, it just returns regular negative kernel error codes. This patch doesn't affect run time, it's just a clean up. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
Ruslan Babayev <ruslan@babayev.com> Signed-off-by:
-
Sunil Muthuswamy authored
The current vsock code for removal of socket from the list is both subject to race and inefficient. It takes the lock, checks whether the socket is in the list, drops the lock and if the socket was on the list, deletes it from the list. This is subject to race because as soon as the lock is dropped once it is checked for presence, that condition cannot be relied upon for any decision. It is also inefficient because if the socket is present in the list, it takes the lock twice. Signed-off-by:
Sunil Muthuswamy <sunilmut@microsoft.com> Signed-off-by:
-
David S. Miller authored
Jakub Kicinski says: ==================== nfp: add two user friendly errors This small series adds two error messages based on recent bug reports which turned out not to be bugs.. ==================== Signed-off-by: -
Jakub Kicinski authored
Users sometimes mistakenly try to manually bind the PF driver to the VFs, print a warning message in that case. Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by:
Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by:
-
Jakub Kicinski authored
Apparently there are still cards in the wild with a very old management FW. Let's make the error message in that case indicate more clearly that management firmware has to be updated. Signed-off-by:
-
David S. Miller authored
Robert Hancock says: ==================== Microchip KSZ driver enhancements A couple of enhancements to the Microchip KSZ switch driver: one to add PHY register settings for errata workarounds for more stable operation, and another to add a device tree option to change the output clock rate as required by some board designs. ==================== Signed-off-by: -
Robert Hancock authored
The KSZ9477 series chips have a SYNCLKO pin which by default outputs a 25MHz clock, but some board setups require a 125MHz clock instead. Added a microchip,synclko-125 device tree property to allow indicating a 125MHz clock output is required. Signed-off-by:
Robert Hancock <hancock@sedsystems.ca> Signed-off-by:
-
Robert Hancock authored
The Silicon Errata and Data Sheet Clarification documents for the KSZ9477 series of chips describe a number of otherwise undocumented PHY register settings which are required to work around various chip errata. Apply these settings when initializing the PHY ports on these chips. Signed-off-by:
-
Martin Blumenstingl authored
Switch stmmac_mdio_reset to use GPIO descriptors. GPIO core handles the "snps,reset-gpio" for GPIO descriptors so we don't need to take care of it inside the driver anymore. The advantage of this is that we now preserve the GPIO flags which are passed via devicetree. This is required on some newer Amlogic boards which use an Open Drain pin for the reset GPIO. This pin can only output a LOW signal or switch to input mode but it cannot output a HIGH signal. There are already devicetree bindings for these special cases and GPIO core already takes care of them but only if we use GPIO descriptors instead of GPIO numbers. Signed-off-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
David S. Miller authored
Eric Dumazet says: ==================== net/packet: better behavior under DDOS Using tcpdump (or other af_packet user) on a busy host can lead to catastrophic consequences, because suddenly, potentially all cpus are spinning on a contended spinlock. Both packet_rcv() and tpacket_rcv() grab the spinlock to eventually find there is no room for an additional packet. This patch series align packet_rcv() and tpacket_rcv() to both check if the queue is full before grabbing the spinlock. If the queue is full, they both increment a new atomic counter placed on a separate cache line to let readers drain the queue faster. There is still false sharing on this new atomic counter, we might in the future make it per cpu if there is interest. ==================== Acked-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Eric Dumazet authored
There are two places where we want to clear the pressure if possible, add a helper to make it more obvious. Signed-off-by:
Eric Dumazet <edumazet@google.com> Suggested-by:
Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by:
-
Eric Dumazet authored
__packet_rcv_has_room() can now be run without lock being held. po->pressure is only a non persistent hint, we can mark all read/write accesses with READ_ONCE()/WRITE_ONCE() to document the fact that the field could be written without any synchronization. Signed-off-by:
-
Eric Dumazet authored
tpacket_rcv() can be hit under DDOS quite hard, since it will always grab a socket spinlock, to eventually find there is no room for an additional packet. Using tcpdump [1] on a busy host can lead to catastrophic consequences, because of all cpus spinning on a contended spinlock. This replicates a similar strategy used in packet_rcv() [1] Also some applications mistakenly use af_packet socket bound to ETH_P_ALL only to send packets. Receive queue is never drained and immediately full. Signed-off-by:
-
Eric Dumazet authored
Under DDOS, we want to be able to increment tp_drops without touching the spinlock. This will help readers to drain the receive queue slightly faster :/ Signed-off-by:
-
Eric Dumazet authored
Goal is use the helper without lock being held. Signed-off-by:
-
Eric Dumazet authored
Goal is to be able to use __tpacket_v3_has_room() without holding a lock. Signed-off-by:
-
Eric Dumazet authored
Goal is to be able to use __tpacket_has_room() without holding a lock. Signed-off-by:
-
Eric Dumazet authored
struct packet_sock is only read. Signed-off-by:
-
Robert Hancock authored
Commit "net: phy: Add detection of 1000BaseX link mode support" added support for not filtering out 1000BaseX mode from the PHY's supported modes in genphy_config_init, but we have to make a similar change in genphy_read_abilities in order to actually detect it as a supported mode in the first place. Add this in. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Ivan Khoronzhuk authored
Only for consistency reasons, do it like in main cpsw.c module and use ndev reference but not by means of slave. Signed-off-by:
Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by:
-
Ivan Khoronzhuk authored
No need to set ndev for drvdata when mainly cpsw reference is needed, so correct this legacy decision. Reviewed-by:
Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by:
-
- 14 Jun, 2019 4 commits
-
-
David S. Miller authored
Paolo Abeni says: ==================== net/mlx5: use indirect call wrappers The mlx5_core driver uses several indirect calls in fast-path, some of them are invoked on each ingress packet, even for the XDP-only traffic. This series leverage the indirect call wrappers infrastructure the avoid the expansive RETPOLINE overhead for 2 indirect calls in fast-path. Each call is addressed on a different patch, plus we need to introduce a couple of additional helpers to cope with the higher number of possible direct-call alternatives. v2 -> v3: - do not add more INDIRECT_CALL_* macros - use only the direct calls always available regardless of the mlx5 build options in the last patch v1 -> v2: - update the direct call list and use a macro to define it, as per Saeed suggestion. An intermediated additional macro is needed to allow arg list expansion - patch 2/3 is unchanged, as the generated code looks better this way than with possible alternative (dropping BP hits) ==================== Signed-off-by: -
Paolo Abeni authored
We can avoid another indirect call per packet wrapping the rx handler call with the proper helper. To ensure that even the last listed direct call experience measurable gain, despite the additional conditionals we must traverse before reaching it, I tested reversing the order of the listed options, with performance differences below noise level. Together with the previous indirect call patch, this gives ~6% performance improvement in raw UDP tput. v2 -> v3: - use only the direct calls always available regardless of the mlx5 build options - drop the direct call list macro, to keep the code as simple as possible for future rework v1 -> v2: - update the direct call list and use a macro to define it, as per Saeed suggestion. An intermediated additional macro is needed to allow arg list expansion Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Acked-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
Paolo Abeni authored
We can avoid an indirect call per packet wrapping the skb creation with the appropriate helper. Signed-off-by:
-
David S. Miller authored
Merge tag 'mac80211-next-for-davem-2019-06-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Johannes Berg says: ==================== Many changes all over: * HE (802.11ax) work continues * WPA3 offloads * work on extended key ID handling continues * fixes to honour AP supported rates with auth/assoc frames * nl80211 netlink policy improvements to fix some issues with strict validation on new commands with old attrs ==================== Signed-off-by:
-
