Switchdev has been around for quite a while now, putting "EXPERIMENTAL"
in the description is no longer accurate, drop it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
1GbE Intel Wired LAN Driver Updates 2016-05-13

This series contains updates to e1000e, igb and igbvf.

Steve Shih fixes an issue for disabling auto-negotiation and forcing
speed and duplex settings for non-copper media.

Brian Walsh cleanups some inconsistency in the use of return variables
names to avoid confusion.

Jake cleans up the drivers to use the BIT() macro when it can, which will
future proof the drivers for GCC 6 when it gets released.  Cleaned up
dead code which was never being used.  Also fixed e1000e, where it was
incorrectly restting the SYSTIM registers every time the ioctl was being
run.

Denys Vlasenko fixes an oversight where incvalue variable holds a 32
bit value so we should declare it as such, instead of 64 bits.  Also
fixed an overflow check, where two reads are the same, then it is not
an overflow.

Nathan Sullivan fixes the PTP timestamps for transmit and receive
latency based on the current link speed.

Alexander Duyck adds support for partial GSO segmentation in the case
of tunnels for igb and igbvf.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The e1000e_config_hwtstamp function was incorrectly resetting the SYSTIM
registers every time the ioctl was being run. If you happened to be
running ptp4l and lost the PTP connect (removing cable, or blocking the
UDP traffic for example), then ptp4l will eventually perform a restart
which involves re-requesting timestamp settings. In e1000e this has the
unfortunate and incorrect result of resetting SYSTIME to the kernel
time. Since kernel time is usually in UTC, and PTP time is in TAI, this
results in the leap second being re-applied.

Fix this by extracting the SYSTIME reset out into its own function,
e1000e_ptp_reset, which we call during reset to restore the hardware
registers. This function will (a) restart the timecounter based on the
new system time, (b) restore the previous PPB setting, and (c) restore
the previous hwtstamp settings.

In order to perform (b), I had to modify the adjfreq ptp function
pointer to store the old delta each time it is called. This also has the
side effect of restoring the correct base timinca register correctly.
The driver does not need to explicitly zero the ptp_delta variable since
the entire adapter structure comes zero-initialized.
Reported-by: Brian Walsh <brian@walsh.ws>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brian Walsh <brian@walsh.ws>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for partial GSO segmentation in the case of
tunnels.  Specifically with this change the driver an perform segmentation
as long as the frame either has IPv6 inner headers, or we are allowed to
mangle the IP IDs on the inner header.  This is needed because we will not
be modifying any fields from the start of the start of the outer transport
header to the start of the inner transport header as we are treating them
like they are just a block of IP options.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The E1000_ICH_NVM_SIG_MASK value is shifted, out to the 31st bit, which
is the signed bit for signed constants. Mark these values as unsigned to
prevent compiler warnings and issues on platforms which a different
signed bit implementation.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This prevents signed bitshift issues when the shift would overwrite the
signed bit, and prevents making this mistake in the future when copying
and modifying code.

Use GENMASK or the unsigned postfix for cases which aren't suitable for
BIT() macro.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

To prevent signed bitshift issues, and improve code readability, use the
BIT() macro. Also make use of GENMASK or the unsigned postfix where this
is more appropriate than BIT()
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The variable rdlen is set but never used, and thus setting it is dead
code. Remove it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Table 7-62 on page 338 of the i210 datasheet lists TX and RX latencies
for the various speeds the chip supports.  To give better PTP timestamp
accuracy, adjust the timestamps by the amounts Intel gives based on
current link speed.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

SYSTIMH:SYSTIML registers are incremented by 24-bit value TIMINCA[23..0]

er32(SYSTIML) are probably moderately expensive (they are pci bus reads).
Can we avoid one of them? Yes, we can.

If the SYSTIML value we see is smaller than 0xff000000, the overflow
into SYSTIMH would require at least two increments.

We do two reads, er32(SYSTIML) and er32(SYSTIMH), in this order.

Even if one increment happens between them, the overflow into SYSTIMH
is impossible, and we can avoid doing another er32(SYSTIML) read
and overflow check.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If two consecutive reads of the counter are the same, it is also
not an overflow.  "systimel_1 < systimel_2" should be
"systimel_1 <= systimel_2".

Before the patch, we could perform an *erroneous* correction:

Let's say that systimel_1 == systimel_2 == 0xffffffff.
"systimel_1 < systimel_2" is false, we think it's an overflow,
we read "systimeh = er32(SYSTIMH)" which meanwhile had incremented,
and use "(systimeh << 32) + systimel_2" value which is 2^32 too large.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: intel-wired-lan@lists.osuosl.org
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

"incvalue" variable holds a result of "er32(TIMINCA) &
E1000_TIMINCA_INCVALUE_MASK" and used in "do_div(temp, incvalue)"
as a divisor.

Thus, "u64 incvalue" declaration is probably a mistake.
Even though it seems to be a harmless one, let's fix it.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

For bitshifts, we should make use of the BIT macro when possible, and
ensure that other bitshifts are marked as unsigned. This helps prevent
signed bitshift errors, and ensures similar style.

Make use of GENMASK and the unsigned postfix where BIT() isn't
appropriate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fixed the file to use a consistent ret_val for return value checking.
Signed-off-by: Brian Walsh <brian@walsh.ws>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the issues for disabling auto-negotiation and forcing
speed and duplex settings for the non-copper media.

For non-copper media, e1000_get_settings should return ETH_TP_MDI_INVALID for
eth_tp_mdix_ctrl instead of ETH_TP_MDI_AUTO so subsequent e1000_set_settings
call would not fail with -EOPNOTSUPP.

e1000_set_spd_dplx should not automatically turn autoneg back on for forced
1000 Mbps full duplex settings for non-copper media.

Cc: xe-kernel@external.cisco.com
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Steve Shih <sshih@cisco.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

While testing an OpenStack configuration using VXLANs I saw the following
call trace:

 RIP: 0010:[<ffffffff815fad49>] udp4_lib_lookup_skb+0x49/0x80
 RSP: 0018:ffff88103867bc50  EFLAGS: 00010286
 RAX: ffff88103269bf00 RBX: ffff88103269bf00 RCX: 00000000ffffffff
 RDX: 0000000000004300 RSI: 0000000000000000 RDI: ffff880f2932e780
 RBP: ffff88103867bc60 R08: 0000000000000000 R09: 000000009001a8c0
 R10: 0000000000004400 R11: ffffffff81333a58 R12: ffff880f2932e794
 R13: 0000000000000014 R14: 0000000000000014 R15: ffffe8efbfd89ca0
 FS:  0000000000000000(0000) GS:ffff88103fd80000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 0000000000000488 CR3: 0000000001c06000 CR4: 00000000001426e0
 Stack:
  ffffffff81576515 ffffffff815733c0 ffff88103867bc98 ffffffff815fcc17
  ffff88103269bf00 ffffe8efbfd89ca0 0000000000000014 0000000000000080
  ffffe8efbfd89ca0 ffff88103867bcc8 ffffffff815fcf8b ffff880f2932e794
 Call Trace:
  [<ffffffff81576515>] ? skb_checksum+0x35/0x50
  [<ffffffff815733c0>] ? skb_push+0x40/0x40
  [<ffffffff815fcc17>] udp_gro_receive+0x57/0x130
  [<ffffffff815fcf8b>] udp4_gro_receive+0x10b/0x2c0
  [<ffffffff81605863>] inet_gro_receive+0x1d3/0x270
  [<ffffffff81589e59>] dev_gro_receive+0x269/0x3b0
  [<ffffffff8158a1b8>] napi_gro_receive+0x38/0x120
  [<ffffffffa0871297>] gro_cell_poll+0x57/0x80 [vxlan]
  [<ffffffff815899d0>] net_rx_action+0x160/0x380
  [<ffffffff816965c7>] __do_softirq+0xd7/0x2c5
  [<ffffffff8107d969>] run_ksoftirqd+0x29/0x50
  [<ffffffff8109a50f>] smpboot_thread_fn+0x10f/0x160
  [<ffffffff8109a400>] ? sort_range+0x30/0x30
  [<ffffffff81096da8>] kthread+0xd8/0xf0
  [<ffffffff81693c82>] ret_from_fork+0x22/0x40
  [<ffffffff81096cd0>] ? kthread_park+0x60/0x60

The following trace is seen when receiving a DHCP request over a flow-based
VXLAN tunnel.  I believe this is caused by the metadata dst having a NULL
dev value and as a result dev_net(dev) is causing a NULL pointer dereference.

To resolve this I am replacing the check for skb_dst(skb)->dev with just
skb->dev.  This makes sense as the callers of this function are usually in
the receive path and as such skb->dev should always be populated.  In
addition other functions in the area where these are called are already
using dev_net(skb->dev) to determine the namespace the UDP packet belongs
in.

Fixes: 63058308 ("udp: Add udp6_lib_lookup_skb and udp4_lib_lookup_skb")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sunrpc is using SOCKWQ_ASYNC_NOSPACE without setting SOCK_FASYNC,
so the recent optimizations done in sk_set_bit() and sk_clear_bit()
broke it.

There is still the risk that a subsequent sock_fasync() call
would clear SOCK_FASYNC, but sunrpc does not use this yet.

Fixes: 9317bb69 ("net: SOCKWQ_ASYNC_NOSPACE optimizations")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jiri Pirko <jiri@resnulli.us>
Reported-by: Huang, Ying <ying.huang@intel.com>
Tested-by: Jiri Pirko <jiri@resnulli.us>
Tested-by: Huang, Ying <ying.huang@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When an ACTIVATE or data packet is received in a link in state
ESTABLISHING, the link does not immediately change state to
ESTABLISHED, but does instead return a LINK_UP event to the caller,
which will execute the state change in a different lock context.

This non-atomic approach incurs a low risk that we may have two
LINK_UP events pending simultaneously for the same link, resulting
in the final part of the setup procedure being executed twice. The
only potential harm caused by this it that we may see two LINK_UP
events issued to subsribers of the topology server, something that
may cause confusion.

This commit eliminates this risk by checking if the link is already
up before proceeding with the second half of the setup.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the hardcoded mask 0x00fffff0 with MICREL_PHY_ID_MASK for
better readability.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When dealing with WCCP in gre6 tunnel, it sets the wrong tpi->protocol,
that is, ETH_P_IP instead of ETH_P_IPV6 for the encapuslated traffic.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not include attribute IFLA_GRE_TOS.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a netns leak.

Fixes: 93edb8c7 ("gtp: reload GTPv1 header after pskb_may_pull()")
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-davem-2016-05-12' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
Some more work for 4.7, notably:
 * completion and fixups of nla_put_64_64bit() work
 * remove a/b/g/n from wext nickname to avoid confusion
   with 11ac (which wouldn't even fit fully there due to
   string length restrictions)

along with some other minor changes/cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When using RSS, frames might not be processed in the correct order,
and thus AP_LINK_PS must be used; most likely with firmware keeping
track of the powersave state, this is the case in iwlwifi now.

In this case, the driver can use ieee80211_sta_ps_transition() to
still have mac80211 manage powersave buffering. However, for U-APSD
and PS-Poll this isn't sufficient. If the device can't manage that
entirely on its own, mac80211's code should be used.

To allow this, export two functions: ieee80211_sta_uapsd_trigger()
and ieee80211_sta_pspoll().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There's no harm in having drivers read the list, since they can
use RCU protection or RTNL locking; allow this to not require
each and every driver to also implement its own bookkeeping.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The devlist_mtx mutex was removed about two years ago, in favour of just
using RTNL/RCU protection. Remove the comment still referencing it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This allows finding vendor IE from a specific vendor.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Some hardware (iwlwifi an example) de-aggregate AMSDUs and copy the IV
as is to the generated MPDUs, so the same PN appears in multiple
packets without being a replay attack.  Allow driver to explicitly
indicate that a frame is allowed to have the same PN as the previous
frame.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In some cases, after a sudden AP disappearing and reconnection to
another AP in the same ESS, user space gets the old AP in scan
results (cached). User space may decide to roam to that old AP
which will cause a disconnection and longer recovery.
Remove APs that are probably out of range from BSS table.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Yuval Mintz says:

====================
qed*: Add SR-IOV support

This patch adds SR-IOV support to qed/qede drivers, adding a new PCI
device ID for a VF that is shared between all the various PFs that
support IOV.

This is quite a massive series - the first 7 parts of the series add
the infrastructure of supporting vfs in qed - mainly adding support in a
HW-based vf<->pf channel, as well as diverging all existing configuration
flows based on the pf/vf decision. I.e., while PF-originated requests
head directly to HW/FW, the VF requests first have to traverse to the PF
which will perform the configuration.

The 8th patch is the one that adds the support for the VF device in qede.

The remaining 6 patches each adds some user-based API support related to
VFs that can be used over the PF - forcing mac/vlan, changing speed, etc.

Dave,

Sorry in advance for the length of the series. Most of the bulk here is in
the infrastructure patches that have to go together [or at least, it makes
little sense to try splitting them up].

Please consider applying this to `net-next'.

Thanks,
Yuval

Changes from previous revision:
------------------------------
 - V2 - Replace aligned_u64 with regular u64; This was possible as the
        shared structures [between PF and VF] were already sufficiently
        padded as-is in the API, making this redundant.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Device should be configured by default to VEB once VFs are active.
This changes the configuration of both PFs' and VFs' vports into enabling
tx-switching once sriov is enabled.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allows the user to view the VF configuration by observing the PF's
device.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support in `ndo_set_vf_spoofchk' for allowing PF control over
its VF spoof-checking configuration.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds support in 2 ndo that allow PF to tweak the VF's view of the
link - `ndo_set_vf_link_state' to allow it a view independent of the PF's,
and `ndo_set_vf_rate' which would allow the PF to limit the VF speed.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allows the PF to enforce the VF's mac.
i.e., by using `ip link ... vf <x> mac <value>'.

While a MAC is forced, PF would prevent the VF from configuring any other
MAC.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds support for PF control over the VF vlan configuration.
I.e., `ip link ... vf <x> vlan <vid>' should now be supported.

 1. <vid> != 0 => VF receives [unknowingly] only traffic tagged by
    <vid> and tags all outgoing traffic sent by VF with <vid>.
 2. <vid> == 0 ==> Remove the pvid configuration, reverting to previous.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding a PCI callback for `sriov_configure' and a new PCI device id for
the VF [+ Some minor changes to accomodate differences between PF and VF
at the qede].
Following this, VF creation should be possible and the entire subset of
existing PF functionality that's allow to VFs should be supported.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As the VF infrastructure is supposed to offer backward/forward
compatibility, the various types associated with VF<->PF communication
should be aligned across all various platforms that support IOV
on our family of adapters.

This adds a couple of currently missing values, specifically aligning
the enum for the various TLVs possible in the communication between them.

It then adds the PF implementation for some of those missing VF requests.
This support isn't really necessary for the Linux VF as those VFs aren't
requiring it [at least today], but are required by VFs running on other
OSes. LRO is an example of one such configuration.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Up to this point, VF and PF communication always originates from VF.
As a result, VF cannot be notified of any async changes, and specifically
cannot be informed of the current link state.

This introduces the bulletin board, the mechanism through which the PF
is going to communicate async notifications back to the VF. basically,
it's a well-defined structure agreed by both PF and VF which the VF would
continuously poll and into which the PF would DMA messages when needed.
[Bulletin board is actually allocated and communicated in previous patches
but never before used]

Based on the bulletin infrastructure, the VF can query its link status
and receive said async carrier changes.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>