From: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This patch seem to have been lost, so here it is again.  It fixes an Ooops
on unregistering hwifs due to the device model now having mandatory
release() functions.  It also close the possible race we had on release if
the entry was in use (by or /sys typically) by using a semaphore waiting
for the release() to be called after doing an unregister.

Include vmalloc.h to fix compilation of raw1394.c

  o scsi/imm.h: use c99 style initialization

  As far as I verified this also fixes a bug when doing the
  table lookup for IMM_EPP_32, that would result in "Unknown"
  as IMM_EPP_32 is equal to 6 and there is the #ifdef...

ChangeSet@1.1386, 2003-09-02 00:11:07-03:00, acme@allegro.kerneljanitors.org
  o scsi/*.h: remove not needed #define NULL

ChangeSet@1.1385, 2003-09-02 00:05:16-03:00, acme@allegro.kerneljanitors.org
  o scsi/3w-xxx.h: use c99 style init

We had some races where we testecd (or set) TS_USEDFPU together
with sequences that depended on the setting (like clearing or
setting the TS flag in %cr0) and we could be preempted in between,
which screws up the FPU state, since preemption will itself change
USEDFPU and the TS flag.

This makes it a lot more explicit: the "internal" low-level FPU
functions ("__xxxx_fpu()") all require preemption to be disabled,
and the exported "real" functions will make sure that is the case.

One case - in __switch_to() - was switched to the non-preempt-safe
internal version, since the scheduler itself has already disabled
preemption.

From Tejun's posting:
>
> This patch fixes a race between del_timer_sync and recursive timers.
> Current implementation allows the value of timer->base that is used
> for timer_pending test to be fetched before finishing running_timer
> test, so it's possible for a recursive time to be pending after
> del_timer_sync.  Adding smp_rmb before timer_pending removes the race.

subsys   : - Added hpsb_make_streampacket() helper
           - Fix re-probe of bus after reset, when node's generation
	     changes
	   - Missing spinlock.h include for csr.c

general  : - Fix a few warnings from size mismatches in printk's

raw1394  : - Added RAW1394_REQ_ASYNC_STREAM
           - Use vmalloc/vfree for larger buffer support

ohci1394 : - Fix a few endianess bugs in ISO routines

eth1394  : - Fix cleanup of failed packets

into home.osdl.org:/home/torvalds/v2.5/linux

where it belongs.

into home.osdl.org:/home/torvalds/v2.5/linux

when programming PCI cache line size.

Just to be on the safe side.  Suggested by Ingo Oeser.

into redhat.com:/spare/repo/net-drivers-2.5

Helpers moved:
netif_poll_{enable,disable}, __netif_rx_complete, netif_tx_disable

Use the helpers in net/core/dev.c.

This patch creates a sections.h for the m68knommu architecture.
Nothing special needed, just an include of the generic code.

This patch creates a local.h for the m68knommu arhcitecture. Like
most others architectures it is just an include of the generic one.

The linux/drivers/scsi/sr.c code will issue a MODE_SENSE[_10] command to
a device as the first command sent to the device.  If the device has
just come out of reset, it will likely respond with a UNIT_ATTENTION /
NOT_READY status, which causes the MODE_SENSE to fail.  In fact, the
device may have several UNIT_ATTENTION conditions queued up (power-up
reset, media change, etc.)

This results in the mode page 0x2a data not being properly read and
interpreted.  As an end-effect, things like packet-writing don't work
(because the writeable bit is not set).

The solution to this is to issue one or more TEST_UNIT_READY commands to
the device to clear any pending UNIT_ATTENTION conditions.  This is the
technique used by sd.c -- in fact, this code was lifted directly from
sd.c

At some point in the future, abstraction of this initial TEST_UNIT_READY
code between all high-level SCSI drivers may be apropriate.  For now,
this patch makes sr.c issue TEST_UNIT_READY to clear the UNIT_ATTENTION,
thus allowing the mode page 0x2a code to work properly.  Given the
approaching 2.6.0-final release, I urge that this patch be accepted.

into home.osdl.org:/home/torvalds/v2.5/linux

Also, call pci_disable_device() in PCI ->remove handler,
to match pci_enable_device() in PCI ->probe handler.

(preferred over alloc_etherdev + 8390-specific ethdev_init)

the SG_IO and SCSI_IOCTL_SEND_COMMAND ioctl's. That just
screws things up when the drive is mounted.

If somebody wants exclusive access, he should indicate that
at open time.

into home.osdl.org:/home/torvalds/v2.5/linux

I've been trying to remove these, but apparently new ones crop up. Lets
just call it io scheduler, none of the ones in the kernel are using the
classic elevator algorithm.

From René Scharfe <l.s.r@web.de>

As a result the size of vfat.o drops by 384 bytes in my build.

into home.osdl.org:/home/torvalds/v2.5/linux

into home.osdl.org:/home/torvalds/v2.5/linux

use the PCI layer instead to provide those for us.

* remove PCI_CACHE_LINE_SIZE workaround, PCI core already does
  this for us.  (main change)
* propagate pci_set_dma_mask return value
* add 'ULL' suffix to pci_set_dma_mask arg
* propagate pci_enable_device return value
* call pci_set_mwi, check and propagate its return value
* call pci_clear_mwi and pci_disable_device on close, and probe error
* call iounmap when cleaning up

Modifies drivers atm/eni.c, ide/pci/cmd64x.c, and
ide/pci/ns87415.c.  Ack'd by DaveM.

This implements the needed 'release' callback in order to make
videodev/sysfs happy again.

This reenables the CAPTURE button events in the sonypi driver, which
were lost with the latest patch...

This adds support for software controlled hard drive LED activity.

This is really nice on such machines as Apple Powerbooks, where there is
no such LED in the first place and the sleep/suspend LED isn't used for
anything when the machine is running.

into home.osdl.org:/home/torvalds/v2.5/linux

into home.osdl.org:/home/torvalds/v2.5/linux