- 23 Aug, 2019 9 commits
-
-
Mitch Williams authored
In some circumstances, VF devices can be deactivated while a message is in-flight. In that case, a series of scary error message will be printed in the log. Since these are actually harmless, check for this case and suppress them. No harm, no foul. Signed-off-by:
Mitch Williams <mitch.a.williams@intel.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Dave Ertman authored
The current flag name of "enable-fw-lldp" is a bit cumbersome. Change priv-flag name to "fw-lldp-agent" with a value of on or off. This is more straight-forward in meaning. Signed-off-by:
Dave Ertman <david.m.ertman@intel.com> Tested-by:
-
Jacob Keller authored
The virtchnl interface provides a mechanism for a VF driver to request head writeback support. This feature is deprecated as of AVF 1.0, but older versions of a VF driver may still attempt to request the mode. Since the ice hardware does not support head writeback, we should not accept Tx queue configuration which attempts to enable it. Currently, the driver simply assumes that the headwb_enabled bit will never be set. If a VF driver does request head writeback, the configuration will return successfully, even though head writeback is not enabled. This leaves the VF driver in a non functional state since it is assuming to be operating in head writeback mode. Fix the PF driver to reject any attempt to setup headwb_enabled. Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Tested-by:
-
Michal Swiatkowski authored
In rebuild DCB desired_dcbx_cfg was copy to local_dcbx_cfg, but if DCBX mode is IEEE desired_dcbx_cfg is not initialized by DCBX config from FW. Change logic to copy config value only if mode is set to CEE. If driver copy desired_dcbx_cfg to local_dcbx_cfg in IEEE mode there is problem with globr. System is frozen after two or more globr. Signed-off-by:
Michal Swiatkowski <michal.swiatkowski@intel.com> Tested-by:
-
Dave Ertman authored
When a port is not cabled, but DCBx is enabled in the firmware, the status of DCBx will be NOT_STARTED. This is a valid state for FW enabled and should not be treated as a is_fw_lldp true automatically. Add the code to treat NOT_STARTED as another valid state. Signed-off-by:
-
Brett Creeley authored
Currently we will call synchronize_irq() from the host for VF's. This is not correct, so don't allow it. Signed-off-by:
Brett Creeley <brett.creeley@intel.com> Tested-by:
-
Dave Ertman authored
Currently, only the DCBx status is taken into account to determine if FW LLDP is possible. But there are NVM version coming out with DCBx enabled, and FW LLDP disabled. This is causing errors where the driver sees that DCBx is not disabled, and then tries to register for LLDP MIB change events, and fails. Change the logic to detect both DCBx and LLDP states in the FW engine. Signed-off-by:
-
Dave Ertman authored
For control packets (i.e. LLDP packets) to be able to egress from the main VSI, a bit has to be set in the TX_descriptor. This should only be done for the main VSI and only if the FW LLDP agent is disabled. A bit to allow this also has to be set in the VSI context. Add the logic to add the necessary bits in the VSI context for the PF_VSI and the TX_descriptors for control packets egressing the PF_VSI. Signed-off-by:
-
Ben Wei authored
Update response packet length for the following commands per NC-SI spec - Get Controller Packet Statistics - Get NC-SI Statistics - Get NC-SI Pass-through Statistics command Signed-off-by:
Ben Wei <benwei@fb.com> Reviewed-by:
Justin Lee <justin.lee1@dell.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 22 Aug, 2019 31 commits
-
-
Markus Elfring authored
The dev_kfree_skb() function performs also input parameter validation. Thus the test around the shown calls is not needed. This issue was detected by using the Coccinelle software. Signed-off-by:
Markus Elfring <elfring@users.sourceforge.net> Signed-off-by:
-
Markus Elfring authored
The dev_kfree_skb() function performs also input parameter validation. Thus the test around the shown calls is not needed. This issue was detected by using the Coccinelle software. Signed-off-by:
-
Markus Elfring authored
The dev_kfree_skb() function performs also input parameter validation. Thus the test around the shown calls is not needed. This issue was detected by using the Coccinelle software. Signed-off-by:
-
Markus Elfring authored
The dev_kfree_skb() function performs also input parameter validation. Thus the test around the shown calls is not needed. This issue was detected by using the Coccinelle software. Signed-off-by:
Sean Nyekjaer <sean@geanix.com> Signed-off-by:
-
Markus Elfring authored
The dev_kfree_skb() function performs also input parameter validation. Thus the test around the shown calls is not needed. This issue was detected by using the Coccinelle software. Signed-off-by:
-
Marco Hartmann authored
IEEE 802.3ae clause 45 defines a modified MDIO protocol that uses a two staged access model in order to increase the address space. This patch adds support for C45 MDIO read and write accesses, which are used whenever the MII_ADDR_C45 flag in the regnum argument is set. In case it is not set, C22 accesses are used as before. Signed-off-by:
Marco Hartmann <marco.hartmann@nxp.com> Acked-by:
Fugang Duan <fugang.duan@nxp.com> Signed-off-by:
-
David S. Miller authored
Neil Armstrong says: ==================== dt-bindings: net: meson-dwmac: convert to yaml This patchsets converts the Amlogic Meson DWMAC glue bindings over to YAML schemas using the already converted dwmac bindings. The first patch is needed because the Amlogic glue needs a supplementary reg cell to access the DWMAC glue registers. Changes since v3: - Specified net-next target tree Changes since v2: - Added review tags - Updated allwinner,sun7i-a20-gmac.yaml reg maxItems ==================== Signed-off-by: -
Neil Armstrong authored
Now that we have the DT validation in place, let's convert the device tree bindings for the Synopsys DWMAC Glue for Amlogic SoCs over to a YAML schemas. Reviewed-by:
Rob Herring <robh@kernel.org> Reviewed-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by:
Neil Armstrong <narmstrong@baylibre.com> Signed-off-by:
-
Neil Armstrong authored
The Amlogic Meson DWMAC glue bindings needs a second reg cells for the glue registers, thus update the reg minItems/maxItems to allow more than a single reg cell. Also update the allwinner,sun7i-a20-gmac.yaml derivative schema to specify maxItems to 1. Signed-off-by:
Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== 40GbE Intel Wired LAN Driver Updates 2019-08-22 This series contains updates to i40e driver only. Arnd Bergmann reduces the stack usage which was causing warnings on 32-bit architectures due to large structure sizes for 2 functions getting inlined, so use noinline_for_stack to prevent the compilers from combining the 2 functions. Mauro S. M. Rodrigues fixes an issue when reading an EEPROM from SFP modules that comply with SFF-8472 but do not implement the Digital Diagnostic Monitoring (DDM) interface for i40e. Huhai found we were not checking the return value for configuring the transmit ring and continuing with XDP configuration of the transmit ring. Beilei fixes an issue of shifting signed 32-bit integers. Sylwia adds support for "packet drop mode" to the MAC configuration for admin queue command. This bit controls the behavior when a no-drop packet is blocking a TC queue. Adds support for persistent LLDP by checking the LLDP flag and reading the LLDP from the NVM when enabled. Adrian fixes the "recovery mode" check to take into account which device we are on, since x710 devices have 4 register values to check for status and x722 devices only have 2 register values to check. Piotr Azarewicz bumps the supported firmware API version to 1.9 which extends the PHY access admin queue command support. Jake makes sure the traffic class stats for a VEB are reset when the VEB stats are reset. Slawomir fixes a NULL pointer dereference where the VSI pointer was not updated before passing it to the i40e_set_vf_mac() when the VF is in a reset state, so wait for the reset to complete. Grzegorz removes the i40e_update_dcb_config() which was not using the correct NVM reads, so call i40e_init_dcb() in its place to correctly update the DCB configuration. Piotr Kwapulinski expands the scope of i40e_set_mac_type() since this is needed during probe to determine if we are in recovery mode. Fixed the driver reset path when in recovery mode. Marcin fixed an issue where we were breaking out of a loop too early when trying to get the PHY capabilities. v2: Combined patch 7 & 9 in the original series, since both patches bumped firmware API version. Also combined patches 12 & 13 in the original series, since one increased the scope of checking for MAC and the follow-on patch made use of function within the new scope. ==================== Signed-off-by: -
Marcin Formela authored
Fixed a bug where driver was breaking out of the loop and reporting an error without retrying first. Signed-off-by:
Marcin Formela <marcin.formela@intel.com> Tested-by:
-
Sylwia Wnuczko authored
This patch adds a function to read NVM module data and uses it to read current LLDP agent configuration from NVM API version 1.8. Signed-off-by:
Sylwia Wnuczko <sylwia.wnuczko@intel.com> Tested-by:
-
Piotr Kwapulinski authored
Driver waits after issuing a reset. When a reset takes too long a driver gives up. Implemented by invoking PF reset in a loop. After defined number of unsuccessful PF reset trials it returns error. Without this patch PF reset fails when NIC is in recovery mode. So make i40e_set_mac_type() public. i40e driver requires i40e_set_mac_type() to be public. It is required for recovery mode handling. Without this patch recovery mode could not be detected in i40e_probe(). Signed-off-by:
Piotr Kwapulinski <piotr.kwapulinski@intel.com> Tested-by:
-
Grzegorz Siwik authored
This patch removes function i40e_update_dcb_config(). Instead of i40e_update_dcb_config() we use i40e_init_dcb(), which implements the correct NVM read. Signed-off-by:
Grzegorz Siwik <grzegorz.siwik@intel.com> Tested-by:
-
Slawomir Laba authored
Add update to the VSI pointer passed to the i40e_set_vf_mac function. If VF is in reset state the driver waits in i40e_set_vf_mac function for the reset to be complete, yet after reset the vsi pointer that was passed into this function is no longer valid. The patch updates local VSI pointer directly from pf->vsi array, by using the id stored in VF pointer (lan_vsi_idx). Without this commit the driver might occasionally invoke general protection fault in kernel and disable the OS entirely. Signed-off-by:
Slawomir Laba <slawomirx.laba@intel.com> Tested-by:
-
Jacob Keller authored
The stats structure for the VEB switch statistics is reset periodically, but the tc_stats are not reset at the same time. Signed-off-by:
-
Piotr Azarewicz authored
Upcoming FW increment API version to 1.9 due to Extend PHY access AQ command support. SW is ready for that support as well. Signed-off-by:
Piotr Azarewicz <piotr.azarewicz@intel.com> Tested-by:
-
Adrian Podlawski authored
Function check_recovery_mode had wrong if statement. Now we check proper FWS1B register values, which are responsible for the recovery mode. Recovery mode has 4 values for x710 and 2 for x722. That's why we need 6 different flags which are defined in the code. Now in the if statement, we recognize type of mac address and register value. Without those changes driver could show wrong state. Signed-off-by:
Adrian Podlawski <adrian.podlawski@intel.com> Tested-by:
-
Sylwia Wnuczko authored
This patch adds "drop mode" parameter to set mac config AQ command. This bit controls the behavior when a no-drop packet is blocking a TC queue. 0 – The PF driver is notified. 1 – The blocking packet is dropped and then the PF driver is notified. Signed-off-by:
-
Beilei Xing authored
This patch fixes following error reported by cppcheck: (error) Shifting signed 32-bit value by 31 bits is undefined behaviour Signed-off-by:
Beilei Xing <beilei.xing@intel.com> Signed-off-by:
Ferruh Yigit <ferruh.yigit@intel.com> Tested-by:
-
huhai authored
When i40e_configure_tx_ring(vsi->tx_rings[i]) returns an error, we should exit from i40e_vsi_configure_tx and return the error, instead of continuing to check whether xdp is enable, and configure the xdp transmit ring. Signed-off-by:
huhai <huhai@kylinos.cn> Tested-by:
-
Mauro S. M. Rodrigues authored
Similar to the ixgbe issue fixed in: 655c9141 ("ixgbe: Check DDM existence in transceiver before access) i40e has the same issue when reading eeprom from SFP's module that comply with SFF-8472 but not implement the Digital Diagnostic Monitoring (DDM) interface described in it. The existence of such area is specified by bit 6 of byte 92, set to 1 if implemented. Without this patch, due to not checking this bit i40e fails to read SFP module's eeprom with the follow message: ethtool -m enP51p1s0f0 Cannot get Module EEPROM data: Input/output error Because it fails to read the additional 256 bytes in which it was assumed to exist the DDM data. Signed-off-by:
"Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com> Tested-by:
-
Arnd Bergmann authored
The functions i40e_aq_get_phy_abilities_resp() and i40e_set_fc() both have giant structure on the stack, which makes each one use stack frames larger than 500 bytes. As clang decides one function into the other, we get a warning for exceeding the frame size limit on 32-bit architectures: drivers/net/ethernet/intel/i40e/i40e_common.c:1654:23: error: stack frame size of 1116 bytes in function 'i40e_set_fc' [-Werror,-Wframe-larger-than=] When building with gcc, the inlining does not happen, but i40e_set_fc() calls i40e_aq_get_phy_abilities_resp() anyway, so they add up on the kernel stack just as much. The parts that actually use large stacks don't overlap, so make sure each one is a separate function, and mark them as noinline_for_stack to prevent the compilers from combining them again. Fixes: 0a862b43 ("i40e/i40evf: Add module_types and update_link_info") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Tested-by:
-
Colin Ian King authored
Variable err is initialized to a value that is never read and it is re-assigned later. The initialization is redundant and can be removed. Addresses-Coverity: ("Unused Value") Signed-off-by:Colin Ian King <colin.king@canonical.com> Reviewed-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
David S. Miller authored
Haiyang Zhang says: ==================== Add software backchannel and mlx5e HV VHCA stats This patch set adds paravirtual backchannel in software in pci_hyperv, which is required by the mlx5e driver HV VHCA stats agent. The stats agent is responsible on running a periodic rx/tx packets/bytes stats update. ==================== Signed-off-by: -
Eran Ben Elisha authored
HV VHCA stats agent is responsible on running a preiodic rx/tx packets/bytes stats update. Currently the supported format is version MLX5_HV_VHCA_STATS_VERSION. Block ID 1 is dedicated for statistics data transfer from the VF to the PF. The reporter fetch the statistics data from all opened channels, fill it in a buffer and send it to mlx5_hv_vhca_write_agent. As the stats layer should include some metadata per block (sequence and offset), the HV VHCA layer shall modify the buffer before actually send it over block 1. Signed-off-by:
Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by:
-
Eran Ben Elisha authored
Control agent is responsible over of the control block (ID 0). It should update the PF via this block about every capability change. In addition, upon block 0 invalidate, it should activate all other supported agents with data requests from the PF. Upon agent create/destroy, the invalidate callback of the control agent is being called in order to update the PF driver about this change. The control agent is an integral part of HV VHCA and will be created and destroy as part of the HV VHCA init/cleanup flow. Signed-off-by:
-
Eran Ben Elisha authored
HV VHCA is a layer which provides PF to VF communication channel based on HyperV PCI config channel. It implements Mellanox's Inter VHCA control communication protocol. The protocol contains control block in order to pass messages between the PF and VF drivers, and data blocks in order to pass actual data. The infrastructure is agent based. Each agent will be responsible of contiguous buffer blocks in the VHCA config space. This infrastructure will bind agents to their blocks, and those agents can only access read/write the buffer blocks assigned to them. Each agent will provide three callbacks (control, invalidate, cleanup). Control will be invoked when block-0 is invalidated with a command that concerns this agent. Invalidate callback will be invoked if one of the blocks assigned to this agent was invalidated. Cleanup will be invoked before the agent is being freed in order to clean all of its open resources or deferred works. Block-0 serves as the control block. All execution commands from the PF will be written by the PF over this block. VF will ack on those by writing on block-0 as well. Its format is described by struct mlx5_hv_vhca_control_block layout. Signed-off-by:
-
Eran Ben Elisha authored
Add wrapper functions for HyperV PCIe read / write / block_invalidate_register operations. This will be used as an infrastructure in the downstream patch for software communication. This will be enabled by default if CONFIG_PCI_HYPERV_INTERFACE is set. Signed-off-by:
-
Haiyang Zhang authored
This interface driver is a helper driver allows other drivers to have a common interface with the Hyper-V PCI frontend driver. Signed-off-by:
-
Dexuan Cui authored
Windows SR-IOV provides a backchannel mechanism in software for communication between a VF driver and a PF driver. These "configuration blocks" are similar in concept to PCI configuration space, but instead of doing reads and writes in 32-bit chunks through a very slow path, packets of up to 128 bytes can be sent or received asynchronously. Nearly every SR-IOV device contains just such a communications channel in hardware, so using this one in software is usually optional. Using the software channel, however, allows driver implementers to leverage software tools that fuzz the communications channel looking for vulnerabilities. The usage model for these packets puts the responsibility for reading or writing on the VF driver. The VF driver sends a read or a write packet, indicating which "block" is being referred to by number. If the PF driver wishes to initiate communication, it can "invalidate" one or more of the first 64 blocks. This invalidation is delivered via a callback supplied by the VF driver by this driver. No protocol is implied, except that supplied by the PF and VF drivers. Signed-off-by:
Jake Oshins <jakeo@microsoft.com> Signed-off-by:
Dexuan Cui <decui@microsoft.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by:
-
