- 01 Jun, 2015 40 commits
-
-
Dong Aisheng authored
The imx6sx usdhc is derived from imx6sl, the difference is minor. imx6sx have the errata ESDHC_FLAG_ERR004536 fixed. So introduce a new compatible string for imx6sx to distinguish them. Signed-off-by:
Dong Aisheng <b29396@freescale.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Dong Aisheng authored
Using specific compatible string in binding doc to make the binding more clear. It's also used to avoid checkpatch warning in the future like follows: WARNING: DT compatible string "fsl,imx6sx-usdhc" appears un-documented -- check ./Documentation/devicetree/bindings/ + { .compatible = "fsl,imx6sx-usdhc", .data = &usdhc_imx6sx_data, }, total: 0 errors, 1 warnings, 18 lines checked Signed-off-by: -
Dong Aisheng authored
The uSDHC has an ADMA Length Mismatch errata ERR004536 which may cause ADMA work abnormally. The errata has already been fixed for i.MX6Q TO1.2 and i.MX6DL TO1.1 by enable the bit 7 in 0x6c register. Unfortunately this fix is not included in i.MX6SL. So we disable ADMA for i.MX6SL and use SDMA instead. Signed-off-by:
Dong Aisheng <aisheng.dong@freescale.com> Signed-off-by:
-
Dong Aisheng authored
The usdhc does not have missing card interrupt issue, so don't execute workaround for usdhc. Signed-off-by:
-
Dong Aisheng authored
In esdhc_writel_le() function, there's duplicated checking of the same register as follows: "if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE))". Merge them into one and remove the duplicated one. Signed-off-by:
-
Adrian Hunter authored
Enable detection of HS400 support via capability bit-63 for some Intel host controllers. Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
-
Adrian Hunter authored
Implement the select_drive_strength callback to provide drive strength selection for Intel SPT. Signed-off-by:
-
Adrian Hunter authored
Add a callbak to let host drivers select drive strength. Signed-off-by:
-
Adrian Hunter authored
Add the ability to set eMMC driver strength for HS200 and HS400. Signed-off-by:
-
Adrian Hunter authored
In preparation for supporing drive strength selection for eMMC, read the card's valid driver strengths. Note that though the SD spec uses the term "drive strength", the JEDEC eMMC spec uses the term "driver strength". Signed-off-by:
-
Adrian Hunter authored
In preparation for adding drive strength support for eMMC, add drive_strength to struct mmc_card to record the card drive strength for UHS-I modes and HS200 / HS400. For eMMC this will be needed when switching between HS200 and HS400. Signed-off-by:
-
Adrian Hunter authored
Make a new function out of common code used for drive strength selection. Signed-off-by:
-
Adrian Hunter authored
In preparation for supporting also eMMC drive strength, add the 'card' as a parameter so that the callback can distinguish different types of cards if necessary. Signed-off-by:
-
Adrian Hunter authored
Card drive strength selection uses a callback to which a mask of supported drive strengths is passed. Currently, the bits are checked against the values in the SD specifications. That is not necessary because the callback will anyway match the mask against a valid value. Simplify by taking the mask as is but still ensuring that the default mandatory value (type B) is always supported. Signed-off-by:
-
Adrian Hunter authored
Initialization of UHS-I modes for SD and SDIO cards employs a callback to allow the host driver to choose a drive strength value. Currently that assumes the card drive strength and host driver type must be the same value. Change to let the callback make that decision and return both the card drive strength and host driver type. Signed-off-by:
-
Adrian Hunter authored
IO state variable drv_type could be set during card initialization. Consequently, it must be reset to the default value when setting the initial state. Signed-off-by:
-
Kuninori Morimoto authored
MMCIF IP on R-Car series has parent clock which can be set several rate, and it was not implemented on old SH-Mobile series (= SH-Mobile series parent clock was fixed rate) R-Car series MMCIF can use more high speed access if it setups parent clock. This patch adds parent clock setup method. It will be used if DT has "max-frequency", and then, this driver assumes it is booted on R-Car Gen2 or later SoC. Because SH-Mobile series (which doesn't boot from DT) and R-Car series (which boots from DT) have different divider. Signed-off-by:
Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Tested-by:
Keita Kobayashi <keita.kobayashi.ym@renesas.com> Signed-off-by:
-
Kuninori Morimoto authored
Current sh_mmcif driver is using sh_mmcif_xxx and mmcif_xxx for functions. This patch used sh_mmcif_xxx for all functions. Signed-off-by:
-
Kuninori Morimoto authored
Current sh_mmcif driver is directly using &host->pd->dev in all place. It is not big problem, but it is unreadable, and it can be cause of future bug. This patch adds new sh_mmcif_host_to_dev() and use it. Signed-off-by:
-
Petri Gynther authored
sdhci_do_set_ios() doesn't currently program SDHCI_HOST_CONTROL2 register correctly when host->preset_enabled == false. Add code to handle the missing cases MMC_SET_DRIVER_TYPE_B and MMC_SET_DRIVER_TYPE_D. Signed-off-by:
Petri Gynther <pgynther@google.com> Signed-off-by:
-
Yangbo Lu authored
Add eSDHC compatible list for P2041/P3041/P4080/P5020/P5040. Signed-off-by:
Yangbo Lu <yangbo.lu@freescale.com> Acked-by:
Scott Wood <scottwood@freescale.com> Signed-off-by:
-
Fabian Frederick authored
Use kernel.h macro definition. Signed-off-by:
Fabian Frederick <fabf@skynet.be> Signed-off-by:
-
Doug Anderson authored
Since the regulator used for the SDMMC IO voltage is not expected to draw a lot of current, most systems will probably use an inexpensive LDO for it. LDO regulators apparently have the feature that they don't actively drive the voltage down--they wait for other components in the system to drag the voltage down. Thus they will transition faster under heavy loads and slower under light loads. During an SDMMC voltage change from 3.3V to 1.8V, we are almost certainly under a light load. To be specific: * The regulator is hooked through pulls to CMD0-3 and DAT. Probably the CMD pulls are something like 47K and the DAT is something like 10K. * The card is supposed to be driving DAT0-3 low during voltage change which will draw _some_ current, but not a lot. * The regulator is also provided to the SDMMC host controller, but the SDMMC host controller is in open drain mode during the voltage change and so shouldn't be drawing much current. In order to keep the SDMMC host working properly (or for noise reasons), there might also be a capacitor attached to the SDMMC IO regulator. This also will have the effect of slowing down transitions of the regulator, especially under light loads. From experimental evidence, we've seen the voltage change fail if the card doesn't detect that the voltage fell to less than about 2.3V when we turn on the clock. On one device (that admittedly had a 47K CMD pullup instead of a 10K CMD pullup) we saw that the voltage was just about 2.3V after 5ms and thus the voltage change would sometimes fail. Doubling the delay gave margin and made the voltage change work 100% of the time, despite the slightly weaker CMD pull. At the moment submitting this as an RFC patch since my problem _could_ be fixed by increasing the pull strength (or using a smaller capacitor). However being a little bit more lenient to strange hardware could also be a good thing. Signed-off-by:
Doug Anderson <dianders@chromium.org> Acked-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Zhangfei Gao authored
Make the modalias match driver name, this is required to make module auto-loading work. Signed-off-by:
Zhangfei Gao <zhangfei.gao@linaro.org> CC: Peter Griffin <peter.griffin@linaro.org> Signed-off-by:
-
Zhangfei Gao authored
Make the modalias match driver name, this is required to make module auto-loading work. Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
-
Zhangfei Gao authored
Make the modalias match driver name, this is required to make module auto-loading work. Signed-off-by:
-
Zhangfei Gao authored
Make the modalias match driver name, this is required to make module auto-loading work. Signed-off-by:
-
Lars-Peter Clausen authored
Use the new MMC_CAP2_NO_WRITE_PROTECT to let the core handle the case where no write protect line is present instead of having custom driver code to handle it. dw_mci_of_get_slot_quirks() is slightly refactored to directly modify the mmc_host capabilities instead of returning a quirk mask. Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
-
Zhangfei Gao authored
Support hi6220, tested on hikey board emmc: support hs sd: support hs, sdr12, sdr25 Signed-off-by:
Jorge A. Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org> Signed-off-by:
Dan Yuan <yuandan@hisilicon.com> Signed-off-by:
-
Zhangfei Gao authored
switch_voltage is required on some platform since special register accessing Signed-off-by:
-
Zhangfei Gao authored
Add bindings for hi6220 mmc support Signed-off-by:
-
Kuninori Morimoto authored
card->csd.capacity is defined as "unsigned int", and sector_t is defined as "u64" or "unsigned long" (depends on CONFIG_LBDAF). Thus, sector_t data might have strange data (see below). This patch cast it to typeof(sector_t) Special thanks to coverity <http://www.coverity.com> ex) if sector_t was u64 unsigned int data; sector_t sector; data = 0x800000; sector = (data << 8); // 0xffffffff80000000 sector = (((typeof(sector_t))data) << 8); // 0x80000000 or data = 0x80000000; sector = (data << 8); // 0x0 sector = (((typeof(sector_t))data) << 8); // 0x8000000000 Signed-off-by:
-
Kuninori Morimoto authored
card->ext_csd.enhanced_area_offset is defined as "unsigned long long", and, ext_csd[] is defined as u8. unsigned long long data might have strange data if first bit of ext_csd[] was 1. this patch cast it to (unsigned long long) Special thanks to coverity <http://www.coverity.com> ex) u8 data8; u64 data64; data8 = 0x80; data64 = (data8 << 24); // 0xffffffff80000000 data64 = (((unsigned long long)data8) << 24); // 0x80000000; Signed-off-by:
-
Fabio Estevam authored
Use BUG_ON() instead of an 'if' condition followed by BUG(). The semantic patch that makes this change is available in scripts/coccinelle/misc/bugon.cocci. More information about semantic patching is available at http://coccinelle.lip6.fr/Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
Fabio Estevam authored
Simplify a trivial if-return sequence. Possibly combine with a preceding function call. The semantic patch that makes this change is available in scripts/coccinelle/misc/simple_return.cocci. More information about semantic patching is available at http://coccinelle.lip6.fr/Signed-off-by:
-
Fabio Estevam authored
Simplify a trivial if-return sequence. Possibly combine with a preceding function call. The semantic patch that makes this change is available in scripts/coccinelle/misc/simple_return.cocci. More information about semantic patching is available at http://coccinelle.lip6.fr/Signed-off-by:
-
Fabio Estevam authored
The only user of this driver that has not been converted to fully device tree is the i.MX35 SoC. There is a i.MX35-based board (mach-pcm043.c) that uses platform data to pass wp_gpio and cd_gpio information. Commit 8d86e4fc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()") broke the platform data case by removing mmc_gpio_request_ro() and mmc_gpio_request_cd(), so restore the functionality for the non-dt case. Also, restore the check for ESDHC_CD_CONTROLLER so that we can still support the "fsl,cd-controller" property. Signed-off-by:
-
Fabio Estevam authored
mmc_of_parse() should be placed inside sdhci_esdhc_imx_probe_dt() as it suits only for the dt case. Signed-off-by:
-
Lars-Peter Clausen authored
Allow to specify in the device-tree that no physical write-protect signal is connected to a particular instance of a MMC controller. Setting the property will cause the core will assume that the SD card is always read-write. The name for the new property is 'disable-wp' and was chosen based on the property with the same function from the Synopsys designware mobile storage host controller DT bindings specification. Signed-off-by:
-
Lars-Peter Clausen authored
It is not uncommon to see systems where there is no physical write-protect signal (e.g. when using eMMC or microSD card slots). For some controllers, which have a dedicated write-protection detection logic (like SDHCI controllers), the get_ro() callback can return bogus data in such a case. Instead of handling this on a per controller basis this patch adds a new capability flag to the MMC core that can be set to specify that the result of get_ro() is invalid. When the flag is set the core will not call get_ro() and assume that the card is always read-write. Signed-off-by:
-
