- 12 Dec, 2016 2 commits
-
-
Shiraz Saleem authored
hw_stats is a pointer to i40_iw_dev_stats struct in i40iw_get_hw_stats(). Use hw_stats and not &hw_stats in the memcpy to copy the i40iw device stats data into rdma_hw_stats counters. Fixes: b40f4757 ("IB/core: Make device counter infrastructure dynamic") Cc: stable@vger.kernel.org # 4.7+ Signed-off-by:
Shiraz Saleem <shiraz.saleem@intel.com> Signed-off-by:
Faisal Latif <faisal.latif@intel.com> Signed-off-by:
Doug Ledford <dledford@redhat.com>
-
Thomas Huth authored
The macros I40IW_STAG_KEY_FROM_STAG and I40IW_STAG_INDEX_FROM_STAG are apparently bad - they are using the logical "&&" operation which does not make sense here. It should have been a bitwise "&" instead. Since the macros seem to be completely unused, let's simply remove them so that nobody accidentially uses them in the future. And while we're at it, also remove the unused macro I40IW_CREATE_STAG. Signed-off-by:
Thomas Huth <thuth@redhat.com> Reviewed-by:
Leon Romanovsky <leonro@mellanox.com> Acked-by:
-
- 05 Dec, 2016 24 commits
-
-
Henry Orosco authored
When CQP times out, send a request to LAN driver for reset. Signed-off-by:
Mustafa Ismail <mustafa.ismail@intel.com> Signed-off-by:
Henry Orosco <henry.orosco@intel.com> Signed-off-by:
-
Henry Orosco authored
Remove check for zero 'pages' of unallocated pbles calculated in add_pble_pool(); as it can never be true. Signed-off-by:
-
Shiraz Saleem authored
Fail the connect and return the proper error code if a client is started with local IP address and there is no corresponding loopback listener. Signed-off-by:
-
Shiraz Saleem authored
IRD is not populated on connect request and application is getting 0 for the value. Fill in the correct value on connect request. Signed-off-by:
-
Shiraz Saleem authored
Set the TOS field in IP header with the value passed in from application. If there is mismatch between the remote client's TOS and listener, set the listener Tos to the higher of the two values. Signed-off-by:
-
Shiraz Saleem authored
Add NULL check for ibqp event handler before calling it to report QP events, as it might not initialized. Signed-off-by:
-
Mustafa Ismail authored
Use list_for_each_entry_safe macro for the IPv6 addr list as IPv6 addresses can be deleted while going through the list. Signed-off-by:
-
Mustafa Ismail authored
Disable listeners and disconnect all connected QPs on a netdev interface down event. On an interface up event, the listeners are re-enabled. Signed-off-by:
-
Mustafa Ismail authored
On i40iw device close, disconnect all connected QPs by moving them to error state; and block further QPs, PDs and CQs from being created. Additionally, make sure all resources have been freed before deallocating the ibdev as part of the device close. Signed-off-by:
-
Henry Orosco authored
Add support to allow each independent memory region to be configured for 2MB page size in addition to 4KB page size. Signed-off-by:
-
Henry Orosco authored
Add support to use physically mapped WQ's and MR's if determined that the OS registered user-memory for the region is physically contiguous. This feature will eliminate the need for unnecessarily setting up and using PBL's when not required. Signed-off-by:
-
Henry Orosco authored
The SQ head is incorrectly incremented when the number of WQEs required is greater than the number available. The fix is to use the I40IW_RING_MOV_HEAD_BY_COUNT macro. This checks for the SQ full condition first and only if SQ has room for the request, then we move the head appropriately. Signed-off-by:
-
Henry Orosco authored
The flush_code variable in i40iw_bld_terminate_hdr() is obsolete and the check to set qp->sq_flush is unreachable. Currently flush code is populated in setup_term_hdr() and both SQ and RQ are flushed always as part of the tear down flow. Signed-off-by:
-
Henry Orosco authored
Remove unnecessary check for return code from device_init_pestat() and change func to void. Signed-off-by:
-
Henry Orosco authored
To be consistent, use the runtime check instead of conditional compile. Signed-off-by:
-
Henry Orosco authored
In i40iw_post_send, use the actual page size instead of encoded page size. This is to be consistent with the rest of the file. Signed-off-by:
-
Henry Orosco authored
It is not necessary to check cm_node->iwdev in i40iw_rem_ref_cm_node() as it can never be NULL after a successful call out of i40iw_make_cm_node(). Signed-off-by:
Chien Tin Tung <chien.tin.tung@intel.com> Signed-off-by:
-
Henry Orosco authored
Remove dead code, which isn't executed because we return error if the data size is greater than 48 bytes. Inline data size greater than 48 bytes isn't supported and the maximum WQE size is 64 bytes. Signed-off-by:
Tatyana Nikolova <tatyana.e.nikolova@intel.com> Signed-off-by:
-
Henry Orosco authored
Some resources are consumed internally and not available to the user. After hw is initialized, figure out how many resources are consumed and subtract those numbers from the initial max device capability in i40iw_query_device(). Signed-off-by:
-
Henry Orosco authored
Use memcpy for inline data copy in sends and writes instead of byte by byte copy. Signed-off-by:
-
Henry Orosco authored
If i40iw_open() fails for any reason, the LAN handler is not being removed. Modify i40iw_deinit_device() to always remove the handler. Signed-off-by:
-
Henry Orosco authored
When creating QPs, ensure init_attr->cap.max_recv_sge is clipped to MAX_FRAG_COUNT. Expose MAX_FRAG_COUNT for max_recv_sge and max_send_sge in i40iw_query_qp(). Signed-off-by:
-
Henry Orosco authored
Assign each CEQ vector to a different CPU when possible, then when creating a CQ, use the vector for the CEQ id. This allows completion work to be distributed over multiple cores. Signed-off-by:
-
Henry Orosco authored
Passed in page_size was used as encoded value for writing the WQE and passed in value was usually 4096. This was working out since bit 0 was 0 and implies 4KB pages, but would not work for other page sizes. Signed-off-by:
-
- 03 Dec, 2016 4 commits
-
-
Henry Orosco authored
Set the MAX_IRD and MAX_ORD size negotiated to the maximum supported values. Signed-off-by:
-
Henry Orosco authored
Pre-production silicon incorrectly truncates 4 bytes of the MPA packet in UDP loopback case. Remove the workaround as it is no longer necessary. Signed-off-by:
-
Henry Orosco authored
Remove the parameter to disable message packing and always enable it. Signed-off-by:
-
Henry Orosco authored
Add support for QoS on QPs. Upon device initialization, a map is created from user priority to queue set handles. On QP creation, use ToS to look up the queue set handle for use with the QP. Signed-off-by:
-
- 30 Oct, 2016 10 commits
-
-
Mark Bloch authored
When creating a FWD rule using tc create also a HW counter for this rule. Signed-off-by:
Mark Bloch <markb@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
Leon Romanovsky <leon@kernel.org>
-
Mark Bloch authored
Currently the code supports only drop rules to possess counters, add that ability also for fwd rules. Signed-off-by:
-
Mark Bloch authored
Currently when calling mlx5_add_flow_rule we accept only one flow destination, this commit allows to pass multiple destinations. This change forces us to change the return structure to a more flexible one. We introduce a flow handle (struct mlx5_flow_handle), it holds internally the number for rules created and holds an array where each cell points the to a flow rule. From the consumers (of mlx5_add_flow_rule) point of view this change is only cosmetic and requires only to change the type of the returned value they store. From the core point of view, we now need to use a loop when allocating and deleting rules (e.g given to us a flow handler). Signed-off-by:
-
Mark Bloch authored
When adding a new rule, if we can match it with compare_match_value and flow tag we might be able to insert the rule to the same fte. In order to do that, there must be an overlap between the actions of the fte and the new rule. When updating the action of an existing fte, we must tell the firmware we are doing so. Signed-off-by:
-
Mark Bloch authored
The way we compare between two dests will need to be used in other places in the future, so we factor out the comparison logic between two dests into a separate function. Signed-off-by:
-
Mark Bloch authored
An fte status becomes FS_FTE_STATUS_EXISTING only after it was created in HW. We can use this in order to simplify the logic on what firmware command to use. If the status isn't FS_FTE_STATUS_EXISTING we need to create the fte, otherwise we need only to update it. Signed-off-by:
-
Mark Bloch authored
When adding a new rule to an fte, we need to hold the fte lock until we add that rule to the fte and increase the fte ref count. Fixes: 0c56b975 ("net/mlx5_core: Introduce flow steering API") Signed-off-by:
-
Mohamad Haj Yahia authored
Implement the vf set rate ndo by modifying the TSAR vport rate limit. Signed-off-by:
Mohamad Haj Yahia <mohamad@mellanox.com> Signed-off-by:
-
Mohamad Haj Yahia authored
Add TSAR to the eswitch which will act as the vports rate limiter. Create/Destroy TSAR on Enable/Dsiable SRIOV. Attach/Detach vport to eswitch TSAR on Enable/Disable vport. Signed-off-by:
-
Mohamad Haj Yahia authored
TSAR (stands for Transmit Scheduling ARbiter) is a hardware component that is responsible for selecting the next entity to serve on the transmit path. The arbitration defines the QoS policy between the agents connected to the TSAR. The TSAR is a consist two main features: 1) BW Allocation between agents: The TSAR implements a defecit weighted round robin between the agents. Each agent attached to the TSAR is assigned with a weight and it is awarded transmission tokens according to this weight. 2) Rate limer per agent: Each agent attached to the TSAR is (optionally) assigned with a rate limit. TSAR will not allow scheduling for an agent exceeding its defined rate limit. In this patch we implement the API of manipulating the TSAR. Signed-off-by:
-
