Move mt76x02_set_irq_mask in mt76 module in order to be reused
adding support for mt7603 driver and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This is a new mac80211 driver for Realtek 802.11ac wireless network chips.
rtw88 now supports RTL8822BE/RTL8822CE now, with basic station mode
functionalities. The firmware for both can be found at linux-firmware.

https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git
For RTL8822BE: rtw88/rtw8822b_fw.bin
For RTL8822CE: rtw88/rtw8822c_fw.bin

And for now, only PCI buses (RTL8xxxE) are supported. We will add support
for USB and SDIO in the future. The bus interface abstraction can be seen
in this driver such as hci.h. Most of the hardware setting are the same
except for some TRX path or probing setup should be separated.

Supported:

 * Basic STA/AP/ADHOC mode, and TDLS (STA is well tested)

Missing feature:

 * WOW/PNO
 * USB & SDIO bus (such as RTL8xxxU/RTL8xxxS)
 * BT coexistence (8822B/8822C are combo ICs)
 * Multiple interfaces (for now single STA is better supported)
 * Dynamic hardware calibrations (to improve/stabilize performance)

Potential problems:

 * static calibration spends too much time, and it is painful for
   driver to leave IDLE state. And slows down associate process.
   But reload function are under development, will be added soon!
 * TRX statictics misleading, as we are not reporting status correctly,
   or say, not reporting for "every" packet.

The next patch set should have BT coexistence code since RTL8822B/C are
combo ICs, and the driver for BT can be found after Linux Kernel v4.20.
So it is better to add it first to make WiFi + BT work concurrently.

Although now rtw88 is simple but we are developing more features for it.
Even we want to add support for more chips such as RTL8821C/RTL8814B.

Finally, rtw88 has many authors, listed alphabetically:

Ping-Ke Shih <pkshih@realtek.com>
Tzu-En Huang <tehuang@realtek.com>
Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-next-for-kalle-2019-04-29' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

Fourth batch of patches intended for v5.2

* Fix a bug we introduced in the RX path in a previous patch;
* Add command version parsing from the FW TLVs;
* Some fixes and improvements in the new debugging framework;
* Bump the FW API supported for 22000 series;
* Small improvement in FTM;
* Some RF-Kill interrupt handling fixes;
* Support for a new WoWLAN patterns FW API;
* Other small fixes and improvements;

Add region type checking during regions parsing to avoid attempts to
parse unsupported or illegal region types.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

In iwl_fw_ini_get_trigger_len the driver allocates space for memory
regions regardless of their domain and in iwl_fw_ini_dump_trigger the
driver aborts trigger collection of disabled domain. This diff causes
unneeded memory allocation and traling zeros in the dump file.

Solve this behavior by enforcing domain checking in
iwl_fw_ini_get_trigger_len
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

In the dump info, the driver sets device_family to
IWL_FW_ERROR_DUMP_FAMILY_7 in case IWL_FW_ERROR_DUMP_FAMILY_7 is used or
IWL_FW_ERROR_DUMP_FAMILY_8 otherwise. This information is misleading and
incorrect since the driver sets the device family to 8 to any device that
is from family 8 and later, e.g. device family 9 is represented as 8 in
the dump.
Also, the device family enum is known only to the driver and
does not give any information to the FW developer

Change the device family to HW type to give propper data about the nic
in use.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Allows to configure a periodic data collection
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Add LMAC_ERROR_TABLE and UMAC_ERROR_TABLE region types and handle them
in the same way as we handle DEVICE_MEMORY.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

In newer firmware images there's a command version TLV that
states, for each listed command or notification, which version
of the command and/or notification structure is used. Read and
keep this data to be able to use it in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

We have a solitary and inconspicous ` in the middle of a comment in
this function, which should not be there.  Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Don't use cancel_delayed_work_sync() inside the channel switch
notifications as they are handled synchronously as part of the RX path.
Fix that by replacing it with cancel_delayed_work(). This should be safe
as we don't really care whether the work is already started and in such
case we would disconnect anyway.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Start supporting API version 48 for 22000 series.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Instead of setting the TLC config command according to the
rates the peer supports, make sure that we aren't also
limited by our own rates, so take the minimum between the
peer's supported RX rates and our supported TX rates.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Support fseq tlv and print fseq version to dmesg.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

When the interface that is requesting an FTM measurement is connected
to a BSS, it is possible that the FTM request was originated by an
RRM request from the AP. In this case the station needs to report
the measurement start time in terms of the TSF of the AP.

Since there is no indication in the FTM request itself if the TSF
is needed, always report the TSF if the station is associated.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Add new definitions for the WoWLAN patterns API version 2 and support
for version 2 of the WoWLAN patterns command without implementing the
new features.  With this commit we only supporting the existing
bitmask pattern match.  Use the new version only if the TLV is set.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

If for some reason the device gives us an RX interrupt before we're
ready for it, perhaps during device power-on with misconfigured IRQ
causes mapping or so, we can crash trying to access the queues.

Prevent that by checking that we actually have RXQs and that they
were properly allocated.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

This will let us introduce a mechanism to start with rfkill
faked, and put 0 here to override it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

commit 2785ce00 ("iwlwifi: support new NVM response API")
seems forgot use correct channel_profile in iwl_get_nvm when call
iwl_init_sbands().

Fixes: 2785ce00 ("iwlwifi: support new NVM response API")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

For PCIE wireless device with core revision less than 14, device may miss
PCIE to System Backplane Interrupt via PCIEtoSBMailbox. So add sending
mail box interrupt twice as a hardware workaround.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/wireless/realtek/rtlwifi/rtl8192cu/rf.c: In function 'rtl92cu_phy_rf6052_set_cck_txpower':
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/rf.c:45:7: warning: variable 'turbo_scanoff' set but not used [-Wunused-but-set-variable]

It is not used any more since
commit e9b0784b ("rtlwifi: rtl8192cu: Fix some code in RF handling")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

It is unnecessary to call spin_lock_bh in a tasklet.
Signed-off-by: Jeff Xie <chongguiguzi@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch modifies location of debugfs entries and their naming
conventions to support multiple wireless cards on pcie host.
Selected approach is to use separate directories for different
wireless cards in top-level qtnfmac debugfs directory.

Here is an example that clarifies the chosen naming conventions:

 $ sudo ls /sys/kernel/debug/qtnfmac/
   qtnfmac_pcie:0000:01:00.0
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In ETSI region DFS slave device can operate in two modes on DFS channels:
 - do on-channel radar detection and use higher Tx power
 - don't do radar detection and use lower Tx power as a consequence

Allow user to control that behavior through qtnfmac module parameter.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Channel switch events from firmware should be processed only when STA
is already connected to BSS. On connect this notification is not needed
since full BSS info will be supplied by cfg80211_connect_result.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Bitmaps are defined on unsigned longs, so the usage of u32[2] in the
wlcore driver is incorrect.  As noted by Peter Zijlstra, casting arrays
to a bitmap is incorrect for big-endian architectures.

When looking at it I observed that:

- operations on reg_ch_conf_pending is always under the wl_lock mutex,
so set_bit is overkill

- the only case where reg_ch_conf_pending is accessed a u32 at a time is
unnecessary too.

This patch cleans up everything in this area, and changes tmp_ch_bitmap
to have the proper alignment.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This reverts commit 99d94ef3. I accidentally
applied this broken (failed to compile) patch due to a bug in my patchwork
script.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

For PCIE wireless device with core revision less than 14, device may miss
PCIE to System Backplane Interrupt via PCIEtoSBMailbox. So add sending
mail box interrupt twice as a hardware workaround.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Patch add support for RT3883 chip. Code was taken direclty
from openwrt project and merge into one patch.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The ACEPC T8 and T11 mini PCs contain quite generic names in the sys_vendor
and product_name DMI strings, without this patch brcmfmac will try to load:
"brcmfmac43455-sdio.Default string-Default string.txt" as nvram file which
is way too generic.

The DMI strings on which we are matching are somewhat generic too, but
"To be filled by O.E.M." is less common then "Default string" and the
system-sku and bios-version strings are pretty unique. Beside the DMI
strings we also check the wifi-module chip-id and revision. I'm confident
that the combination of all this is unique.

Both the T8 and T11 use the same wifi-module, this commit adds DMI
quirks for both mini PCs pointing to brcmfmac43455-sdio.acepc-t8.txt .

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1690852
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The function p54p_probe takes an extra reference count of the PCI
device. However, the extra reference count is not dropped when it fails
to enable the PCI device. This patch fixes the bug.

Cc: stable@vger.kernel.org
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add missing break statement in order to prevent the code from falling
through to case 0x1025, and erroneously setting rtlhal->oem_id to
RT_CID_819X_ACER when rtlefuse->eeprom_svid is equal to 0x10EC and
none of the cases in switch (rtlefuse->eeprom_smid) match.

This bug was found thanks to the ongoing efforts to enable
-Wimplicit-fallthrough.

Fixes: 238ad2dd ("rtlwifi: rtl8723ae: Clean up the hardware info routine")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

There various spelling mistakes in function names and in message
text. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Fix spelling mistakes in rx stats text. I missed these from an earlier
round of fixing the same spelling mistake.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch adds support for Marvell 88W8987 chipset with SDIO interface.
Register offsets and supported feature flags are updated. The corresponding
firmware image file shall be "mrvl/sd8987_uapsta.bin".
Signed-off-by: Tamás Szűcs <tszucs@protonmail.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

It was reported on OpenWrt bug tracking system[1], that several users
are affected by the endless reboot of their routers if they configure
5GHz interface with channel 44 or 48.

The reboot loop is caused by the following excessive number of WARN_ON
messages:

 WARNING: CPU: 0 PID: 0 at backports-4.19.23-1/net/mac80211/rx.c:4516
                             ieee80211_rx_napi+0x1fc/0xa54 [mac80211]

as the messages are being correctly emitted by the following guard:

 case RX_ENC_LEGACY:
      if (WARN_ON(status->rate_idx >= sband->n_bitrates))

as the rate_idx is in this case erroneously set to 251 (0xfb). This fix
simply converts previously used magic number to proper constant and
guards against substraction which is leading to the currently observed
underflow.

1. https://bugs.openwrt.org/index.php?do=details&task_id=2218

Fixes: 85478344 ("mwl8k: properly set receive status rate index on 5 GHz receive")
Cc: <stable@vger.kernel.org>
Tested-by: Eubert Bao <bunnier@gmail.com>
Reported-by: Eubert Bao <bunnier@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Syzkaller report this:

[ 1213.468581] BUG: unable to handle kernel paging request at fffffbfff83bf338
[ 1213.469530] #PF error: [normal kernel read fault]
[ 1213.469530] PGD 237fe4067 P4D 237fe4067 PUD 237e60067 PMD 1c868b067 PTE 0
[ 1213.473514] Oops: 0000 [#1] SMP KASAN PTI
[ 1213.473514] CPU: 0 PID: 6321 Comm: syz-executor.0 Tainted: G         C        5.1.0-rc3+ #8
[ 1213.473514] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
[ 1213.473514] RIP: 0010:strcmp+0x31/0xa0
[ 1213.473514] Code: 00 00 00 00 fc ff df 55 53 48 83 ec 08 eb 0a 84 db 48 89 ef 74 5a 4c 89 e6 48 89 f8 48 89 fa 48 8d 6f 01 48 c1 e8 03 83 e2 07 <42> 0f b6 04 28 38 d0 7f 04 84 c0 75 50 48 89 f0 48 89 f2 0f b6 5d
[ 1213.473514] RSP: 0018:ffff8881f2b7f950 EFLAGS: 00010246
[ 1213.473514] RAX: 1ffffffff83bf338 RBX: ffff8881ea6f7240 RCX: ffffffff825350c6
[ 1213.473514] RDX: 0000000000000000 RSI: ffffffffc1ee19c0 RDI: ffffffffc1df99c0
[ 1213.473514] RBP: ffffffffc1df99c1 R08: 0000000000000001 R09: 0000000000000004
[ 1213.473514] R10: 0000000000000000 R11: ffff8881de353f00 R12: ffff8881ee727900
[ 1213.473514] R13: dffffc0000000000 R14: 0000000000000001 R15: ffffffffc1eeaaf0
[ 1213.473514] FS:  00007fa66fa01700(0000) GS:ffff8881f7200000(0000) knlGS:0000000000000000
[ 1213.473514] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1213.473514] CR2: fffffbfff83bf338 CR3: 00000001ebb9e005 CR4: 00000000007606f0
[ 1213.473514] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 1213.473514] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 1213.473514] PKRU: 55555554
[ 1213.473514] Call Trace:
[ 1213.473514]  led_trigger_register+0x112/0x3f0
[ 1213.473514]  led_trigger_register_simple+0x7a/0x110
[ 1213.473514]  ? 0xffffffffc1c10000
[ 1213.473514]  at76_mod_init+0x77/0x1000 [at76c50x_usb]
[ 1213.473514]  do_one_initcall+0xbc/0x47d
[ 1213.473514]  ? perf_trace_initcall_level+0x3a0/0x3a0
[ 1213.473514]  ? kasan_unpoison_shadow+0x30/0x40
[ 1213.473514]  ? kasan_unpoison_shadow+0x30/0x40
[ 1213.473514]  do_init_module+0x1b5/0x547
[ 1213.473514]  load_module+0x6405/0x8c10
[ 1213.473514]  ? module_frob_arch_sections+0x20/0x20
[ 1213.473514]  ? kernel_read_file+0x1e6/0x5d0
[ 1213.473514]  ? find_held_lock+0x32/0x1c0
[ 1213.473514]  ? cap_capable+0x1ae/0x210
[ 1213.473514]  ? __do_sys_finit_module+0x162/0x190
[ 1213.473514]  __do_sys_finit_module+0x162/0x190
[ 1213.473514]  ? __ia32_sys_init_module+0xa0/0xa0
[ 1213.473514]  ? __mutex_unlock_slowpath+0xdc/0x690
[ 1213.473514]  ? wait_for_completion+0x370/0x370
[ 1213.473514]  ? vfs_write+0x204/0x4a0
[ 1213.473514]  ? do_syscall_64+0x18/0x450
[ 1213.473514]  do_syscall_64+0x9f/0x450
[ 1213.473514]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 1213.473514] RIP: 0033:0x462e99
[ 1213.473514] Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
[ 1213.473514] RSP: 002b:00007fa66fa00c58 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
[ 1213.473514] RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99
[ 1213.473514] RDX: 0000000000000000 RSI: 0000000020000300 RDI: 0000000000000003
[ 1213.473514] RBP: 00007fa66fa00c70 R08: 0000000000000000 R09: 0000000000000000
[ 1213.473514] R10: 0000000000000000 R11: 0000000000000246 R12: 00007fa66fa016bc
[ 1213.473514] R13: 00000000004bcefa R14: 00000000006f6fb0 R15: 0000000000000004

If usb_register failed, no need to call led_trigger_register_simple.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 1264b951 ("at76c50x-usb: add driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

If pci_map_single() fails in mwl8k_post_cmd(),
it returns -ENOMEM immediately, while cleanup is required.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In commit d825db346270e ("b43: shut up clang -Wuninitialized variable
warning"), the message noted that function lpphy_papd_cal() was empty
and had an old TODO regarding its implementation. As the reverse
engineering project that created the LP-PHY version of this driver
has not been active for some time, it is safe to remove this empty
function.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The "rate_index" is only used as an index into the phist_data->rx_rate[]
array in the mwifiex_hist_data_set() function.  That array has
MWIFIEX_MAX_AC_RX_RATES (74) elements and it's used to generate some
debugfs information.  The "rate_index" variable comes from the network
skb->data[] and it is a u8 so it's in the 0-255 range.  We need to cap
it to prevent an array overflow.

Fixes: cbf6e055 ("mwifiex: add rx histogram statistics support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>