It belongs to the endo layer and should be placed in endo.c instead. Do
it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The module will be released by gb_module_release() once all references
for the module are dropped. And so there is no need to free it in the
error path specially.
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The interface will be released by gb_interface_release() once all
references for the interface are dropped. And so there is no need to
free it in the error path specially.
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The bundle will be released by gb_bundle_release() once all references
for the bundle are dropped. And so there is no need to free it in the
error path specially.
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

During endo registration, a unique device id was allocated but then
never used. Instead the default dev_id 0 (due to kzalloc) was used for
device-generation and later for id-deallocation.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Fix use-after-free in endo-registration error path by moving the
id-release to the device release function.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

With DB3, we now have AP as a master as far as AP bridges are concerned.
SVC will talk only to AP and AP will control bridges; unlike other
module interfaces.

So AP supposed to manage/control bridges in all power states including
power on reset.

During power on reset AP should follow below sequence -

Sequence (treated as a Cold Boot)

Stage-1
=======
AP:
 - Power On (Power up from PMIC to AP)
 - AP start booting
   Since power to AP bridges are controlled through gpio, power is gated
   to APB1 & 2
   No ref_clk to APB available (under SVC's control)
 - AP configures USB hub to enable HSIC interface to APB
 - As part of platform driver probe, AP follow below sequence
   - Set the pinctrl in default state
   - Hold APBs in reset by pulling down reset pin
   - Enable power to APB by enabling regulator and switches
   - De-assert (set 'low') 'boot_ret' signal
 - AP will assert (set 'high') the wake_detect signal, triggering
   connect/detect event to the SVC
 - AP waits for wake pulse from SVC

 SVC:
 - Power On (power up from PMIC to SVC)
 - SVC starts booting
 - SVC will de-assert reset signal to unipro switch
   - Switch starts booting
 - SVC confirms switch boot status using SPI (or something)
 - SVC waits for 300 msec (ES2 known issue)
 - SVC waits for detect/connect event from AP

Stage-2
=======
SVC:
 - ON connect/detect event, SVC send back wake pulse (cold boot)
   to AP over wake_detect pin, if SVC boot is completed.

AP:
 - On wake pulse from SVC (for cold boot), AP de-asserts (set high')
   reset signal to APB 1 and/or 2
 - Bridges starts booting
 - Eventually Unipro linkup occurs

Testing:

 - Build tested against Helium kernel
 - Due to unavailability of MSM and DB3 platform, only minimal testing
   has been done.
 - Code has been modified for validation on Helium + SDB platform.
    Mostly dts changes for gpio numbers
    And debug messages to check gpio values
 - On Helium + SDB platform, with addition of debug messages validated
   the sequence.

TODO list:

 - Currently _only_ supports power on sequence (cold boot).
   Both warm and cold boot support. Cold and Warm boot is
   differentiated based on pulse width of wake_detect signal
      >=5 msec = Cold boot else Warm boot
 - No support for Power management
   So the "power-down", "power-off", "wake_in" and "wake_out"
   signals are not explored/implemented.
 - Support for Work thread
    repetitive wake signal if no response from peer
    May required for PM support, as we have delays in the sequences
 - pinctrl states, specially to make sure we enable right pullup or pulldown
   when we set wake_detect pin to input
 - Convert gpio list into an array, and associated xxx-gpio-name property
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

As the svc code is "odd" in how things are set up at initial connection
time, we can't always "know" that we have a valid bundle to use for
error messages.  So just punt and always use pr_*() calls to ensure that
we never incorrectly dereference a pointer.

This will get fixed up soon, but for now, let's just live with a bit
messier error messages in the log.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>

As we are going to be removing the struct device from gb_connection,
there is no need to do anything for uevents for them.  So just remove
the code.  It wasn't doing anything anyway, so no functionality is lost
here at all.

As is_gb_connection() is no longer used, that is also removed in this
patch.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>

The gb_bundle structure needs a private field if we are going to be able
to replace the gb_connection device with this one for all use cases.

Ideally we could use the private pointer within the struct device, but
for now let's just try to mirror how people were using the gb_connection
structure to make the patches simpler, and the logic the same.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>

We are removing struct device from the gb_connection structure in the
near future.  The gb_bundle structure's struct device should be used as
a replacement.

This patch moves the protocol code to use the bundle pointer instead of
the connection pointer when printing out error messages.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>

We are removing struct device from the gb_connection structure in the
near future.  The gb_bundle structure's struct device should be used as
a replacement.

This patch moves the greybus trace code to use the bundle pointer
instead of the connection pointer when printing out tracing messages.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>

We are removing struct device from the gb_connection structure in the
near future.  The gb_bundle structure's struct device should be used as
a replacement.

This patch moves the loopback driver to use the bundle pointer instead
of the connection pointer.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>

We are removing struct device from the gb_connection structure in the
near future.  The gb_bundle structure's struct device should be used as
a replacement.

This patch moves the connection code to use the bundle pointer instead
of the connection pointer for some error messages.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>

We don't want this in the driver core, as nothing will be binding to it,
that's the job of a bundle.  So remove the struct device and use a kref
to handle reference counting instead.

Note, I don't think we really need a kref, but it keeps the lifetime the
same as before, and is the simplest change for now.  In the future it
might be easier to just attach all connections to the bundle and clean
them up when the bundle is removed.

Also remove the cport sysfs documentation as it's no longer relevant.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>

Some cleanups in gb_sdio_command function, ret does not need to be
initialize and mrq is already pointing to request, no need to get it
from host.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

If SDIO request include data to be transfer send details (data blocks
and block size) in command request, as it seems some controllers need
this info prior to set the registers correctly.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

In order to provide deep inspection of the greybus/UniPro system
instrumentation of

1. APBridge's view of UniPro latency
2. GPBridge's view of internal firmware-only latency

have both been added and reported to the AP in the transfer loopback
response header. When this data are present we latch and average it over
the number of requested cycles, presenting it to user-space via sysfs.

This patch adds the following sysfs entries for each loopback CPort

- apbridge_unipro_latency_avg_con
- apbridge_unipro_latency_max_con
- apbridge_unipro_latency_min_con
- gpbridge_firmware_latency_avg_con
- gpbridge_firmware_latency_max_con
- gpbridge_firmware_latency_min_con

and the following sysfs entries representing the average values across all
available CPorts

- apbridge_unipro_latency_avg_dev
- apbridge_unipro_latency_max_dev
- apbridge_unipro_latency_min_dev
- gpbridge_firmware_latency_avg_dev
- gpbridge_firmware_latency_max_dev
- gpbridge_firmware_latency_min_dev
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This patch adds tracker variables to hold the incoming firmware derived
timestamps where apbridge_latency_ts will contain the APBridge's view of
the UniPro turn-around time and gpbridge_latency_ts will contain the
GPBridge's view of it's own internal latency. Both values are reported
in microseconds.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

A USB vendor command has been added to APBridge to allow for tagging of
specific CPort identifiers with internal timing data, specifically geared
towards capturing and understanding latencies in the UniPro fabric. This
patch sends a command to APBridge for each known loopback CPort to tag data
as appropriate. Subsequent patches will present this data to user-space for
ongoing integration analysis.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This patch adds a layered wrapper around optional latency tag
enable/disable commands to APBridge. When set APBridge and GPBridge will
insert timing information into reserved fields in the loopback response
header. Correspondingly when unset no timing information will be included
in the response payload.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

As part of an effort to get deep inspection of latencies throughout the
greybus network including HSIC, UniPro and firmware incurred latencies a
new command to the APBridge to tag a known offset with timestamping data
has been introduced. This patch adds that code to the es1 and es2 drivers.

- latency_tag_enable
- latency_tag_disable

Respectively send the enable/disable command to APBridge on a per-CPort
basis. This allows only specified cports to have timestamping data added by
APBridge, leaving any CPort not specifically enabled untouched.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

We are removing struct device from the gb_connection structure in the
near future.  The gb_bundle structure's struct device should be used as
a replacement.

This patch moves the raw driver to use the bundle pointer instead of the
connection pointer.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>

We are removing struct device from the gb_connection structure in the
near future.  The gb_bundle structure's struct device should be used as
a replacement.

This patch moves the control code to use the bundle pointer instead
of the connection pointer for printing out error messages.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>

We are removing struct device from the gb_connection structure in the
near future.  The gb_bundle structure's struct device should be used as
a replacement.

This patch moves the operation code to use to use the bundle pointer
instead of the connection pointer when printing out error messages.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>

We are removing struct device from the gb_connection structure in the
near future.  The gb_bundle structure's struct device should be used as
a replacement.

This patch moves the usb driver to use the bundle pointer instead of the
connection pointer.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>

We are removing struct device from the gb_connection structure in the
near future.  The gb_bundle structure's struct device should be used as
a replacement.

This patch moves the sdio driver to use the bundle pointer instead of
the connection pointer.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>

We are removing struct device from the gb_connection structure in the
near future.  The gb_bundle structure's struct device should be used as
a replacement.

This patch moves the light driver to use the bundle pointer instead of
the connection pointer.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>

We are removing struct device from the gb_connection structure in the
near future.  The gb_bundle structure's struct device should be used as
a replacement.

This patch moves the pwm driver to use the bundle pointer instead of the
connection pointer.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>

We are removing struct device from the gb_connection structure in the
near future.  The gb_bundle structure's struct device should be used as
a replacement.

This patch moves the i2c driver to use the bundle pointer instead of the
connection pointer.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>

We are removing struct device from the gb_connection structure in the
near future.  The gb_bundle structure's struct device should be used as
a replacement.

This patch moves the gpio driver to use the bundle pointer instead of
the connection pointer.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>

We are removing struct device from the gb_connection structure in the
near future.  The gb_bundle structure's struct device should be used as
a replacement.

This patch moves the firmware driver to use the bundle pointer instead
of the connection pointer.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>

We are removing struct device from the gb_connection structure in the
near future.  The gb_bundle structure's struct device should be used as
a replacement.

This patch moves the audio driver to use the bundle pointer instead of
the connection pointer.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>

We are removing struct device from the gb_connection structure in the
near future.  The gb_bundle structure's struct device should be used as
a replacement.

This patch moves the hid driver to use the bundle pointer instead of the
connection pointer.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>

We are removing struct device from the gb_connection structure in the
near future.  The gb_bundle structure's struct device should be used as
a replacement.

This patch moves the spi driver to use the bundle pointer instead of the
connection pointer.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>

We are removing struct device from the gb_connection structure in the
near future.  The gb_bundle structure's struct device should be used as
a replacement.

This patch moves the uart driver to use the bundle pointer instead of
the connection pointer.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>

We are removing struct device from the gb_connection structure in the
near future.  The gb_bundle structure's struct device should be used as
a replacement.

This patch moves the vibrator driver to use the bundle pointer instead
of the connection pointer.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>

The greybus specification has been extended to include two new reserved
fields, which the implementation is using to track internal firmware
latencies. This change adds the appropriate fields to the corresponding
kernel header.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The ARM-specific set_irq_flags helper has been removed in 4.3. Instead
of doing conditional compilation on the kernel version to avoid build
breakages, simply use the genirq interface directly.
Suggested-by: Rob Herring <rob.herring@linaro.org>
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add PWM to the kernel config options that shall be enabled.

When PWM is not enabled connection init will fail with

	greybus endo0:3:4:9:9: failed to register PWM: -22

when using the default manifest.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>