This patch updates the interrupts part of the Marvell PPv2 driver
bindings documentation, to keep it in sync with the driver.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch renames the IRQs in the Marvell PPv2 driver as their current
names match the way they are used in software. But this will change in
the future, and those IRQs have nothing to do with Rx/Tx interrupts
(this can be configured). The new binding also describe more interrupts
as some where left out.

The old binding support is kept for backward compatibility.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch sets the number of s/w threads to 9, its maximum value,
instead of 8. This is not a fix as only 4 of the s/w threads were used
so far, but more could be used in the future.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch sets from two descriptor to one descriptor because R-Car Gen3
does not have the 4 bytes alignment restriction of the transmission buffer.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: make phy_stop() synchronous

There have been few not that successful attempts in the past to make
phy_stop() a synchronous call instead of just changing the state.
Patch 1 of this series addresses an issue which prevented this change.
At least for me it works fine now. Would appreciate if Geert could
re-test as well that suspend doesn't throw an error.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

phy_stop() may be called e.g. when suspending, therefore all needed
actions should be performed synchronously. Therefore add a synchronous
call to the state machine.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When bringing down the netdevice (incl. detaching it) and calling
netif_carrier_off directly or indirectly the latter triggers an
asynchronous linkwatch event.
This linkwatch event eventually may fail to access chip registers in
the ndo_get_stats/ndo_get_stats64 callback because the device isn't
accessible any longer, see call trace in [0].

To prevent this scenario don't check for IFF_UP only, but also make
sure that the netdevice is present.

[0] https://lists.openwall.net/netdev/2018/03/15/62Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

zhong jiang says:

====================
net: Use FIELD_SIZEOF directly instead of reimplementing its function

The issue is detected with the help of Coccinelle.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

FIELD_SIZEOF is defined as a macro to calculate the specified value. Therefore,
We prefer to use the macro rather than calculating its value.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

FIELD_SIZEOF is defined as a macro to calculate the specified value. Therefore,
We prefer to use the macro rather than calculating its value.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

FIELD_SIZEOF is defined as a macro to calculate the specified value. Therefore,
We prefer to use the macro rather than calculating its value.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

FIELD_SIZEOF is defined as a macro to calculate the specified value. Therefore,
We prefer to use the macro rather than calculating its value.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

FIELD_SIZEOF is defined as a macro to calculate the specified value. Therefore,
We prefer to use the macro rather than calculating its value.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
This feature/cleanup patchset includes the following patches:

 - bump version strings, by Simon Wunderlich

 - Inform users about debugfs interface deprecation, by Sven Eckelmann

 - Implement tracing, planned to replace debugfs log messages,
   by Sven Eckelmann

 - Move OGM rebroadcasts to per interface struct, by Sven Eckelmann

 - Enable LockLess TX to increase throughput, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

module.h already contained moduleparam.h,  so it is safe to remove
the redundant include.

The issue is detected with the help of Coccinelle.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

module.h already contained moduleparam.h,  so it is safe to remove
the redundant include.

The issue is detected with the help of Coccinelle.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Corentin Labbe says:

====================
net: ethernet: neterion: use linux/io-64-nonatomic-lo-hi.h

This series remove usage of custom writeq/readq in favor of ones
defined in linux/io-64-nonatomic-lo-hi.h

This series is only compile tested.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch replace the custom definition of writeq/read and use ones
defined in linux/io-64-nonatomic-lo-hi.h.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch replace the custom definition of writeq/read and use ones
defined in linux/io-64-nonatomic-lo-hi.h.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, also the implementation in this
driver has returns 'netdev_tx_t' value, so just change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove duplicated include.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

struct pcpu_vstats and pcpu_lstats have same members and
usage, and pcpu_lstats is used in many files, so rename
pcpu_vstats as pcpu_lstats to reduce duplicate definition
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commonly, ethernet addresses are just using a policy of
	{ .len = ETH_ALEN }
which leaves userspace free to send more data than it should,
which may hide bugs.

Introduce NLA_EXACT_LEN which checks for exact size, rejecting
the attribute if it's not exactly that length. Also add
NLA_EXACT_LEN_WARN which requires the minimum length and will
warn on longer attributes, for backward compatibility.

Use these to define NLA_POLICY_ETH_ADDR (new strict policy) and
NLA_POLICY_ETH_ADDR_COMPAT (compatible policy with warning);
these are used like this:

    static const struct nla_policy <name>[...] = {
        [NL_ATTR_NAME] = NLA_POLICY_ETH_ADDR,
        ...
    };
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In some situations some netlink attributes may be used for output
only (kernel->userspace) or may be reserved for future use. It's
then helpful to be able to prevent userspace from using them in
messages sent to the kernel, since they'd otherwise be ignored and
any future will become impossible if this happens.

Add NLA_REJECT to the policy which does nothing but reject (with
EINVAL) validation of any messages containing this attribute.
Allow for returning a specific extended ACK error message in the
validation_data pointer.

While at it clear up the documentation a bit - the NLA_BITFIELD32
documentation was added to the list of len field descriptions.

Also, use NL_SET_BAD_ATTR() in one place where it's open-coded.

The specific case I have in mind now is a shared nested attribute
containing request/response data, and it would be pointless and
potentially confusing to have userspace include response data in
the messages that actually contain a request.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2018-09-18

This series contains changes to i40evf so that it becomes a more
generic virtual function driver for current and future silicon.

While doing the rename of i40evf to a more generic name of iavf,
we also put the driver on a severe diet due to how much of the
code was unneeded or was unused.  The outcome is a lean and mean
virtual function driver that continues to work on existing 40GbE
(i40e) virtual devices and prepped for future supported devices,
like the 100GbE (ice) virtual devices.

This solves 2 issues we saw coming or were already present, the
first was constant code duplication happening with i40e/i40evf,
when much of the duplicate code in the i40evf was not used or was
not needed.  The second was to remove the future confusion of why
future VF devices that were not considered "40GbE" only devices
were supported by i40evf.

The thought is that iavf will be the virtual function driver for
all future devices, so it should have a "generic" name to properly
represent that it is the VF driver for multiple generations of
devices.

The last patch in this series is unreleated to the iavf conversion
and just has to do with a MODULE_LICENSE correction.

Known Caveats:
Existing user space configurations may have to change, but the module
alias in patch 1 helps a bit here.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We recently updated all our SPDX identifiers to correctly
indicate our net/ethernet/intel/* drivers were always released
and intended to be released under GPL v2, but the MODULE_LICENSE
declaration was never updated.

Fix the MODULE_LICENSE to be GPL v2, for all our drivers.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This finishes the process of renaming the files that
make sense to rename (skipping adminq related files that
talk to i40e), and fixes up the build and the #includes
so that everything builds nicely.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This is the big rename patch, it takes most of the i40e_
and I40E_ strings and renames them to iavf_ and IAVF_.

Some of the adminq code, as well as most of the client
interface code used by RDMA is left unchanged in order
to indicate that the driver is talking to non-internal to
iavf code.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Rename the i40e_trace file and fix up all the callers
to the new names inside the iavf_trace.h file.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Change another string (i40e_debug)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix up the i40e_hw names to new name, including versions
inside other strings.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Take care of some renames containing I40E_ADMINQ_DESC.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Rename the device ID defines to have IAVF in them
and remove all the unused defines.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove the register name references to I40E_VF* and change to
IAVF_VF. Update the descriptor names and defines to the IAVF
name.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Simply move the i40evf files to the new name, updating the #includes
to track the new names, and updating the Makefile as well.

A future patch will remove the i40e references (after the code
removal patches later in this series).
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This is just a rename of an internal variable i40e_status, but
it was a pretty big change and so deserved it's own patch.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This basically begins the internal portion of the rename of i40evf to iavf,
by renaming many of the functions, structs, variables and defines.

Most of the changes were made mechanically, which introduces some
alignment issues.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove a bunch of unused code and reformat a few lines. Also
remove some now un-necessary files.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>