Recently, DMG frequency bands have been extended till 71GHz, so extend
the range check till 20GHz (45-71GHZ), else some channels will be marked
as disabled.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@bluwireless.co.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If there are simulatenous queries of regdb, then there might be a case
where multiple queries can trigger request_firmware_no_wait and can have
parallel callbacks being executed asynchronously. In this scenario we
might hit the WARN_ON.

So remove the warn_on, as the code already handles multiple callbacks
gracefully.
Signed-off-by: Chaitanya Tata <chaitanya.tata@bluwireless.co.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

During refactor in commit 9e478066 ("mac80211: fix MU-MIMO
follow-MAC mode") a new struct 'action' was declared with packed
attribute as:

  struct {
          struct ieee80211_hdr_3addr hdr;
          u8 category;
          u8 action_code;
  } __packed action;

But since struct 'ieee80211_hdr_3addr' is declared with an aligned
keyword as:

  struct ieee80211_hdr {
  	__le16 frame_control;
  	__le16 duration_id;
  	u8 addr1[ETH_ALEN];
  	u8 addr2[ETH_ALEN];
  	u8 addr3[ETH_ALEN];
  	__le16 seq_ctrl;
  	u8 addr4[ETH_ALEN];
  } __packed __aligned(2);

Solve the ambiguity of placing aligned structure in a packed one by
adding the aligned(2) attribute to struct 'action'.

This removes the following warning (W=1):

  net/mac80211/rx.c:234:2: warning: alignment 1 of 'struct <anonymous>' is less than 2 [-Wpacked-not-aligned]

Cc: Johannes Berg <johannes.berg@intel.com>
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Following call trace is observed while adding TDLS peer entry in driver
during TDLS setup.

Call Trace:
[<c1301476>] dump_stack+0x47/0x61
[<c10537d2>] __warn+0xe2/0x100
[<fa22415f>] ? sta_apply_parameters+0x49f/0x550 [mac80211]
[<c1053895>] warn_slowpath_null+0x25/0x30
[<fa22415f>] sta_apply_parameters+0x49f/0x550 [mac80211]
[<fa20ad42>] ? sta_info_alloc+0x1c2/0x450 [mac80211]
[<fa224623>] ieee80211_add_station+0xe3/0x160 [mac80211]
[<c1876fe3>] nl80211_new_station+0x273/0x420
[<c170f6d9>] genl_rcv_msg+0x219/0x3c0
[<c170f4c0>] ? genl_rcv+0x30/0x30
[<c170ee7e>] netlink_rcv_skb+0x8e/0xb0
[<c170f4ac>] genl_rcv+0x1c/0x30
[<c170e8aa>] netlink_unicast+0x13a/0x1d0
[<c170ec18>] netlink_sendmsg+0x2d8/0x390
[<c16c5acd>] sock_sendmsg+0x2d/0x40
[<c16c6369>] ___sys_sendmsg+0x1d9/0x1e0

Fixing this by allowing TDLS setup request only when we have completed
association.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

syzbot reported an out-of-bounds read when passing certain
malformed messages into nl80211. The specific place where
this happened isn't interesting, the problem is that nested
policy parsing was referring to the wrong maximum attribute
and thus the policy wasn't long enough.

Fix this by referring to the correct attribute. Since this
is really not necessary, I'll come up with a separate patch
to just pass the policy instead of both, in the common case
we can infer the maxattr from the size of the policy array.

Reported-by: syzbot+4157b036c5f4713b1f2f@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Fixes: 9bb7e0f2 ("cfg80211: add peer measurement with FTM initiator API")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.

Fixes: c7cdba31 ("mac80211-next: rtnetlink wifi simulation device")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In ieee80211_rx_h_mesh_fwding, we increment the 'dropped_frames_ttl'
counter when we decrement the ttl to zero.  For unicast frames
destined for other hosts, we stop processing the frame at that point.

For multicast frames, we do not rebroadcast it in this case, but we
do pass the frame up the stack to process it on this STA.  That
doesn't match the usual definition of "dropped," so don't count
those as such.

With this change, something like `ping6 -i0.2 ff02::1%mesh0` from a
peer in a ttl=1 network no longer increments the counter rapidly.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Under certain circumstances, radios created via netlink could
have n_limits be zero and no possible interface types, which
makes no sense. Reject this early to prevent a WARN_ON() in
cfg80211.

Fixes: 99e3a44b ("mac80211_hwsim: allow setting iftype support")
Reported-by: syzbot+73fd8b0aa60c67fa4b60@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2019-01-18

This series introduces some fixes to mlx5 driver.

Please pull and let me know if there is any problem.

For -stable v4.18
('net/mlx5e: Force CHECKSUM_UNNECESSARY for short ethernet frames')

The patch doesn't apply cleanly to 4.18.y, but it is very simple to
resolve, what should be the procedure here ?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously the identifier used for indirect block callback registry
and for block rule cb registry (when done via indirect blocks) was the
pointer to the tunnel netdev we were interested in receiving updates on.
This worked fine if a single PF existed that registered one callback for
the tunnel netdev of interest. However, if multiple PFs are in place then
the 2nd PF tries to register with the same tunnel netdev identifier. This
leads to EEXIST errors and/or incorrect cb deletions.

Prevent this conflict by using the rpriv pointer as the identifier for
netdev indirect block cb registry, allowing each PF to register a unique
callback per tunnel netdev. For block cb registry, the same PF may
register multiple cbs to the same block if using TC shared blocks.
Instead of the rpriv, use the pointer to the allocated indr_priv data as
the identifier here. This means that there can be a unique block callback
for each PF/tunnel netdev combo.

Fixes: f5bc2c5d ("net/mlx5e: Support TC indirect block notifications
for eswitch uplink reprs")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

For representors, the TX dropped counter is not folded from the
per-ring counters. Fix it.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Advertised and configured FEC query failure resulted in printing
wrong error code.

Fixes: 6cfa9460 ("net/mlx5e: Ethtool driver callback for query/set FEC policy")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When an ethernet frame is padded to meet the minimum ethernet frame
size, the padding octets are not covered by the hardware checksum.
Fortunately the padding octets are usually zero's, which don't affect
checksum. However, we have a switch which pads non-zero octets, this
causes kernel hardware checksum fault repeatedly.

Prior to:
commit '88078d98 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE ...")'
skb checksum was forced to be CHECKSUM_NONE when padding is detected.
After it, we need to keep skb->csum updated, like what we do for RXFCS.
However, fixing up CHECKSUM_COMPLETE requires to verify and parse IP
headers, it is not worthy the effort as the packets are so small that
CHECKSUM_COMPLETE can't save anything.

Fixes: 88078d98 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"),
Cc: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Ido Schimmel says:

====================
mlxsw: Various fixes

This patchset contains small fixes in mlxsw and one fix in the bridge
driver.

Patches #1-#4 perform small adjustments in PCI and FID code following
recent tests that were performed on the Spectrum-2 ASIC.

Patch #5 fixes the bridge driver to mark FDB entries that were added by
user as such. Otherwise, these entries will be ignored by underlying
switch drivers.

Patch #6 fixes a long standing issue in mlxsw where the driver
incorrectly programmed static FDB entries as both static and sticky.

Patches #7-#8 add test cases for above mentioned bugs.

Please consider patches #1, #2 and #4 for stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Test that externally learned FDB entries can roam, but not age out.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test that externally learned FDB entries added from user space are
marked as offloaded.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver currently treats static FDB entries as both static and
sticky. This is incorrect and prevents such entries from being roamed to
a different port via learning.

Fix this by configuring static entries with ageing disabled and roaming
enabled.

In net-next we can add proper support for the newly introduced 'sticky'
flag.

Fixes: 56ade8fe ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Externally learned entries can be added by a user or by a switch driver
that is notifying the bridge driver about entries that were learned in
hardware.

In the first case, the entries are not marked with the 'added_by_user'
flag, which causes switch drivers to ignore them and not offload them.

The 'added_by_user' flag can be set on externally learned FDB entries
based on the 'swdev_notify' parameter in br_fdb_external_learn_add(),
which effectively means if the created / updated FDB entry was added by
a user or not.

Fixes: 816a3bed ("switchdev: Add fdb.added_by_user to switchdev notifications")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: bridge@lists.linux-foundation.org
Signed-off-by: David S. Miller <davem@davemloft.net>

When using a tc flower action of egress mirred redirect, the driver adds
an implicit FID setting action. This implicit action sets a dummy FID to
the packet and is used as part of a design for trapping unmatched flows
in OVS.  While this implicit FID setting action is supposed to be a NOP
when a redirect action is added, in Spectrum-2 the FID record is
consulted as the dummy FID index is an 802.1D FID index and the packet
is dropped instead of being redirected.

Set the dummy FID index value to be within 802.1Q range. This satisfies
both Spectrum-1 which ignores the FID and Spectrum-2 which identifies it
as an 802.1Q FID and will then follow the redirect action.

Fixes: c3ab4354 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Return an appropriate error in the case when the driver timeouts on waiting
for firmware to go out of PCI reset.

Fixes: 233fa44b ("mlxsw: pci: Implement reset done check")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Spectrum-2 PHY layer introduces a calibration period which is a part of the
Spectrum-2 firmware boot process. Hence increase the SW timeout waiting for
the firmware to come out of boot. This does not increase system boot time
in cases where the firmware PHY calibration process is done quickly.

Fixes: c3ab4354 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a packet should be trapped to the CPU the device consumes a WQE
(work queue element) from an RDQ (receive descriptor queue) and copies
the packet to the address specified in the WQE. The device then tries to
post a CQE (completion queue element) that contains various metadata
(e.g., ingress port) about the packet to a CQ (completion queue).

In case the device managed to consume a WQE, but did not manage to post
the corresponding CQE, it will get stuck. This unlikely situation can be
triggered due to the scheme the driver is currently using to process
CQEs.

The driver will consume up to 512 CQEs at a time and after processing
each corresponding WQE it will ring the RDQ's doorbell, letting the
device know that a new WQE was posted for it to consume. Only after
processing all the CQEs (up to 512), the driver will ring the CQ's
doorbell, letting the device know that new ones can be posted.

Fix this by having the driver ring the CQ's doorbell for every processed
CQE, but before ringing the RDQ's doorbell. This guarantees that
whenever we post a new WQE, there is a corresponding CQE available. Copy
the currently processed CQE to prevent the device from overwriting it
with a new CQE after ringing the doorbell.

Note that the driver still arms the CQ only after processing all the
pending CQEs, so that interrupts for this CQ will only be delivered
after the driver finished its processing.

Before commit 8404f6f2 ("mlxsw: pci: Allow to use CQEs of version 1
and version 2") the issue was virtually impossible to trigger since the
number of CQEs was twice the number of WQEs and the number of CQEs
processed at a time was equal to the number of available WQEs.

Fixes: 8404f6f2 ("mlxsw: pci: Allow to use CQEs of version 1 and version 2")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Semion Lisyansky <semionl@mellanox.com>
Tested-by: Semion Lisyansky <semionl@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update email addresses of liquidio driver maintainers.  Also remove a
former maintainer.
Signed-off-by: Felix Manlunas <fmanlunas@marvell.com>
Acked-by: Derek Chickles <dchickles@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

"also enables" should not be spelled as one word.

Fixes: cfc80d9a ("net: Introduce net_failover driver")
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

In certain cases, pskb_trim_rcsum() may change skb pointers.
Reinitialize header pointers afterwards to avoid potential
use-after-frees. Add a note in the documentation of
pskb_trim_rcsum(). Found by KASAN.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current code in __mdiobus_register() doesn't properly handle
failures returned by the devm_gpiod_get_optional() call: it returns
immediately, without unregistering the device that was added by the
call to device_register() earlier in the function.

This leaves a stale device, which then causes a NULL pointer
dereference in the code that handles deferred probing:

[    1.489982] Unable to handle kernel NULL pointer dereference at virtual address 00000074
[    1.498110] pgd = (ptrval)
[    1.500838] [00000074] *pgd=00000000
[    1.504432] Internal error: Oops: 17 [#1] SMP ARM
[    1.509133] Modules linked in:
[    1.512192] CPU: 1 PID: 51 Comm: kworker/1:3 Not tainted 4.20.0-00039-g3b73a4cc8b3e-dirty #99
[    1.520708] Hardware name: Xilinx Zynq Platform
[    1.525261] Workqueue: events deferred_probe_work_func
[    1.530403] PC is at klist_next+0x10/0xfc
[    1.534403] LR is at device_for_each_child+0x40/0x94
[    1.539361] pc : [<c0683fbc>]    lr : [<c0455d90>]    psr: 200e0013
[    1.545628] sp : ceeefe68  ip : 00000001  fp : ffffe000
[    1.550863] r10: 00000000  r9 : c0c66790  r8 : 00000000
[    1.556079] r7 : c0457d44  r6 : 00000000  r5 : ceeefe8c  r4 : cfa2ec78
[    1.562604] r3 : 00000064  r2 : c0457d44  r1 : ceeefe8c  r0 : 00000064
[    1.569129] Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
[    1.576263] Control: 18c5387d  Table: 0ed7804a  DAC: 00000051
[    1.582013] Process kworker/1:3 (pid: 51, stack limit = 0x(ptrval))
[    1.588280] Stack: (0xceeefe68 to 0xceef0000)
[    1.592630] fe60:                   cfa2ec78 c0c03c08 00000000 c0457d44 00000000 c0c66790
[    1.600814] fe80: 00000000 c0455d90 ceeefeac 00000064 00000000 0d7a542e cee9d494 cfa2ec78
[    1.608998] fea0: cfa2ec78 00000000 c0457d44 c0457d7c cee9d494 c0c03c08 00000000 c0455dac
[    1.617182] fec0: cf98ba44 cf926a00 cee9d494 0d7a542e 00000000 cf935a10 cf935a10 cf935a10
[    1.625366] fee0: c0c4e9b8 c0457d7c c0c4e80c 00000001 cf935a10 c0457df4 cf935a10 c0c4e99c
[    1.633550] ff00: c0c4e99c c045a27c c0c4e9c4 ced63f80 cfde8a80 cfdebc00 00000000 c013893c
[    1.641734] ff20: cfde8a80 cfde8a80 c07bd354 ced63f80 ced63f94 cfde8a80 00000008 c0c02d00
[    1.649936] ff40: cfde8a98 cfde8a80 ffffe000 c0139a30 ffffe000 c0c6624a c07bd354 00000000
[    1.658120] ff60: ffffe000 cee9e780 ceebfe00 00000000 ceeee000 ced63f80 c0139788 cf8cdea4
[    1.666304] ff80: cee9e79c c013e598 00000001 ceebfe00 c013e44c 00000000 00000000 00000000
[    1.674488] ffa0: 00000000 00000000 00000000 c01010e8 00000000 00000000 00000000 00000000
[    1.682671] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    1.690855] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[    1.699058] [<c0683fbc>] (klist_next) from [<c0455d90>] (device_for_each_child+0x40/0x94)
[    1.707241] [<c0455d90>] (device_for_each_child) from [<c0457d7c>] (device_reorder_to_tail+0x38/0x88)
[    1.716476] [<c0457d7c>] (device_reorder_to_tail) from [<c0455dac>] (device_for_each_child+0x5c/0x94)
[    1.725692] [<c0455dac>] (device_for_each_child) from [<c0457d7c>] (device_reorder_to_tail+0x38/0x88)
[    1.734927] [<c0457d7c>] (device_reorder_to_tail) from [<c0457df4>] (device_pm_move_to_tail+0x28/0x40)
[    1.744235] [<c0457df4>] (device_pm_move_to_tail) from [<c045a27c>] (deferred_probe_work_func+0x58/0x8c)
[    1.753746] [<c045a27c>] (deferred_probe_work_func) from [<c013893c>] (process_one_work+0x210/0x4fc)
[    1.762888] [<c013893c>] (process_one_work) from [<c0139a30>] (worker_thread+0x2a8/0x5c0)
[    1.771072] [<c0139a30>] (worker_thread) from [<c013e598>] (kthread+0x14c/0x154)
[    1.778482] [<c013e598>] (kthread) from [<c01010e8>] (ret_from_fork+0x14/0x2c)
[    1.785689] Exception stack(0xceeeffb0 to 0xceeefff8)
[    1.790739] ffa0:                                     00000000 00000000 00000000 00000000
[    1.798923] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    1.807107] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000
[    1.813724] Code: e92d47f0 e1a05000 e8900048 e1a00003 (e5937010)
[    1.819844] ---[ end trace 3c2c0c8b65399ec9 ]---

The actual error that we had from devm_gpiod_get_optional() was
-EPROBE_DEFER, due to the GPIO being provided by a driver that is
probed later than the Ethernet controller driver.

To fix this, we simply add the missing device_del() invocation in the
error path.

Fixes: 69226896 ("mdio_bus: Issue GPIO RESET to PHYs")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix "reference to nonexisting document" warnings.

Fixes: b255e500 ("net: documentation: build a directory structure for drivers")
Signed-off-by: Otto Sabart <ottosabart@seberm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the kfree_skb() by consume_skb() to be drop monitor(dropwatch,
perf) friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the kfree_skb() by consume_skb() to be drop monitor(dropwatch,
perf) friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

The XGBE hardware has support for performing MDIO operations using an
MDIO command request. The driver mistakenly uses the mdio port address
as the MDIO command request device address instead of the MDIO command
request port address. Additionally, the driver does not properly check
for and create a clause 45 MDIO command.

Check the supplied MDIO register to determine if the request is a clause
45 operation (MII_ADDR_C45). For a clause 45 operation, extract the device
address and register number from the supplied MDIO register and use them
to set the MDIO command request device address and register number fields.
For a clause 22 operation, the MDIO request device address is set to zero
and the MDIO command request register number is set to the supplied MDIO
register. In either case, the supplied MDIO port address is used as the
MDIO command request port address.

Fixes: 732f2ab7 ("amd-xgbe: Add support for MDIO attached PHYs")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The phy drivers for CS4340 and TN2020 are missing their
features attributes. Add them.

Fixes: 719655a1 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As txq_trans_update() only updates trans_start when the lock is held,
trans_start does not get updated if NETIF_F_LLTX is declared.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The skb header should be set to ethernet header before using
is_skb_forwardable. Because the ethernet header length has been
considered in is_skb_forwardable(including dev->hard_header_len
length).

To reproduce the issue:
1, add 2 ports on linux bridge br using following commands:
$ brctl addbr br
$ brctl addif br eth0
$ brctl addif br eth1
2, the MTU of eth0 and eth1 is 1500
3, send a packet(Data 1480, UDP 8, IP 20, Ethernet 14, VLAN 4)
from eth0 to eth1

So the expect result is packet larger than 1500 cannot pass through
eth0 and eth1. But currently, the packet passes through success, it
means eth1's MTU limit doesn't take effect.

Fixes: f6367b46 ("bridge: use is_skb_forwardable in forward path")
Cc: bridge@lists.linux-foundation.org
Cc: Nkolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vhost dirty page logging API is designed to sync through GPA. But we
try to log GIOVA when device IOTLB is enabled. This is wrong and may
lead to missing data after migration.

To solve this issue, when logging with device IOTLB enabled, we will:

1) reuse the device IOTLB translation result of GIOVA->HVA mapping to
   get HVA, for writable descriptor, get HVA through iovec. For used
   ring update, translate its GIOVA to HVA
2) traverse the GPA->HVA mapping to get the possible GPA and log
   through GPA. Pay attention this reverse mapping is not guaranteed
   to be unique, so we should log each possible GPA in this case.

This fix the failure of scp to guest during migration. In -next, we
will probably support passing GIOVA->GPA instead of GIOVA->HVA.

Fixes: 6b1e6cc7 ("vhost: new device IOTLB API")
Reported-by: Jintack Lim <jintack@cs.columbia.edu>
Cc: Jintack Lim <jintack@cs.columbia.edu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net_tstamp.h is an UAPI header, so it was moved under include/uapi.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit cb9f1b78, scapy (which uses an AF_PACKET socket in
SOCK_RAW mode) is unable to send a basic icmp packet over a sit tunnel:

Here is a example of the setup:
$ ip link set ntfp2 up
$ ip addr add 10.125.0.1/24 dev ntfp2
$ ip tunnel add tun1 mode sit ttl 64 local 10.125.0.1 remote 10.125.0.2 dev ntfp2
$ ip addr add fd00:cafe:cafe::1/128 dev tun1
$ ip link set dev tun1 up
$ ip route add fd00:200::/64 dev tun1
$ scapy
>>> p = []
>>> p += IPv6(src='fd00:100::1', dst='fd00:200::1')/ICMPv6EchoRequest()
>>> send(p, count=1, inter=0.1)
>>> quit()
$ ip -s link ls dev tun1 | grep -A1 "TX.*errors"
    TX: bytes  packets  errors  dropped carrier collsns
    0          0        1       0       0       0

The problem is that the network offset is set to the hard_header_len of the
output device (tun1, ie 14 + 20) and in our case, because the packet is
small (48 bytes) the pskb_inet_may_pull() fails (it tries to pull 40 bytes
(ipv6 header) starting from the network offset).

This problem is more generally related to device with variable hard header
length. To avoid a too intrusive patch in the current release, a (ugly)
workaround is proposed in this patch. It has to be cleaned up in net-next.

Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=993675a3100b1
Link: http://patchwork.ozlabs.org/patch/1024489/
Fixes: cb9f1b78 ("ip: validate header length on virtual device xmit")
CC: Willem de Bruijn <willemb@google.com>
CC: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 23b0269e ("net: udp6: prefer listeners bound to an
address"), UDP-Lite only works when specifying a local address for
the sockets.

This is related to the problem addressed in the commit 719f8358
("udp: add rehash on connect()"). Moreover, __udp6_lib_lookup() now
looks for a socket immediately in the secondary hash table.

And this issue was found with LTP/network tests as well.

Fixes: 23b0269e ("net: udp6: prefer listeners bound to an address")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 4cdeeee9 ("net: udp: prefer listeners bound to an
address"), UDP-Lite only works when specifying a local address for
the sockets.

This is related to the problem addressed in the commit 719f8358
("udp: add rehash on connect()"). Moreover, __udp4_lib_lookup() now
looks for a socket immediately in the secondary hash table.

The issue was found with LTP/network tests (UDP-Lite test-cases).

Fixes: 4cdeeee9 ("net: udp: prefer listeners bound to an address")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent changes (especially 05cd271f ("cls_flower: Support multiple
masks per priority")) in the fl_flow_mask structure grow it and its
current size e.g. on x86_64 with defconfig is 760 bytes and more than
1024 bytes with some debug options enabled. Prior the mentioned commit
its size was 176 bytes (using defconfig on x86_64).
With regard to this fact it's reasonable to allocate this structure
dynamically in fl_change() to reduce its stack size.

v2:
- use kzalloc() instead of kcalloc()

Fixes: 05cd271f ("cls_flower: Support multiple masks per priority")
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Paul Blakey <paulb@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the new of_get_compatible_child() helper to look up child nodes to
avoid ever matching non-child nodes elsewhere in the tree.

Also fix up the related struct device_node leaks.

Fixes: d8652956 ("net: dsa: realtek-smi: Add Realtek SMI driver")
Cc: stable <stable@vger.kernel.org>     # 4.19: 36156f92
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>