- 20 Jul, 2012 40 commits
-
-
Bart Van Assche authored
When we call scsi_unprep_request() the command associated with the request gets destroyed and therefore drops its reference on the device. If this was the only reference, the device may get released and we end up with a NULL pointer deref when we call blk_requeue_request. Reported-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
Bart Van Assche <bvanassche@acm.org> Reviewed-by:
Tejun Heo <tj@kernel.org> Cc: <stable@kernel.org> [jejb: enhance commend and add commit log for stable] Signed-off-by:
James Bottomley <JBottomley@Parallels.com>
-
Bart Van Assche authored
Use blk_queue_dead() to test whether the queue is dead instead of !sdev. Since scsi_prep_fn() may be invoked concurrently with __scsi_remove_device(), keep the queuedata (sdev) pointer in __scsi_remove_device(). This patch fixes a kernel oops that can be triggered by USB device removal. See also http://www.spinics.net/lists/linux-scsi/msg56254.html. Other changes included in this patch: - Swap the blk_cleanup_queue() and kfree() calls in scsi_host_dev_release() to make that code easier to grasp. - Remove the queue dead check from scsi_run_queue() since the queue state can change anyway at any point in that function where the queue lock is not held. - Remove the queue dead check from the start of scsi_request_fn() since it is redundant with the scsi_device_online() check. Reported-by:
Jun'ichi Nomura <j-nomura@ce.jp.nec.com> Signed-off-by:
-
Muthukumar Ratty authored
If the queue is dead blk_execute_rq_nowait() doesn't invoke the done() callback function. That will result in blk_execute_rq() being stuck in wait_for_completion(). Avoid this by initializing rq->end_io to the done() callback before we check the queue state. Also, make sure the queue lock is held around the invocation of the done() callback. Found this through source code review. Signed-off-by:
Muthukumar Ratty <muthur@gmail.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Dan Carpenter authored
We took this lock with spin_lock() so we should unlock it with spin_unlock() instead of spin_unlock_irq(). This was introduced in f2c8dc40 "[SCSI] megaraid_mbox: remove scsi_assign_lock usage". Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Adam Radford <aradford@gmail.com> Signed-off-by:
-
Dan Carpenter authored
On 64 bit systems the current code sets 32 bits of "seg" and leaves the other 32 uninitialized. It doesn't matter since the variable is never used. But it's still messy and we should fix it. Signed-off-by:
-
Dan Carpenter authored
If bfad_thread_workq(bfad) was not BFA_STATUS_OK then we freed "im" and then dereferenced it. I did a little clean up because it seemed nicer to return directly instead of doing a superfluous goto. I looked at other functions in this file and it seems like returning directly is standard. Signed-off-by:
Krishna Gudipati <kgudipat@brocade.com> Signed-off-by:
-
Dan Carpenter authored
If mc == BFI_MC_MAX then we're reading past the end of the mod->mbhdlr[] array. Signed-off-by:
-
Josh Hunt authored
Initialize atomic_t scsi_host_next_hn and ioerr_cntas per the guidelines defined in Documentation/atomic_ops.txt Signed-off-by:
Josh Hunt <johunt@akamai.com> Signed-off-by:
-
Bart Van Assche authored
A quote from SPC-4: "While in the unavailable primary target port asymmetric access state, the device server shall support those of the following commands that it supports while in the active/optimized state: [ ... ] d) SET TARGET PORT GROUPS; [ ... ]". Hence re-enable sending STPG to a target port group that is in the unavailable state. Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
Vikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Vikas Chaudhary authored
Fix following message:- drivers/scsi/qla4xxx/ql4_os.c:3266:5: error: symbol 'qla4xxx_post_aen_work' redeclared with different type (originally declared at drivers/scsi/qla4xxx/ql4_glbl.h:186) - incompatible argument 2 (different signedness) Signed-off-by:
-
Vikas Chaudhary authored
Allow multi-session to target (for flash ddbs) accesible via multiple network portal Signed-off-by:
-
Rob Evers authored
Currently the backoff algorithm for when to retry alua rtpg requests progresses geometrically as so: 2, 4, 8, 16, 32, 64... seconds. This progression can lead to un-needed delay in retrying alua rtpg requests when the rtpgs are delayed. A less aggressive backoff algorithm that is additive would not lead to such large jumps when delays start getting long, but would backoff linearly: 2, 4, 6, 8, 10... seconds. Signed-off-by:
Martin George <marting@netapp.com> Signed-off-by:
Rob Evers <revers@redhat.com> Reviewed-by:
Babu Moger <babu.moger@netapp.com> Signed-off-by:
-
Rob Evers authored
Some storage arrays are known to return 'illegal request' when an rtpg extended header request is made. T10 says the array should ignore the bit, and return the non-extended rtpg as the array doesn't support the request. Working around this by retrying the rtpg request without the extended header bit set when the extended rtpg request results in illegal request. Signed-off-by:
-
Rob Evers authored
During alua transitions, an array can return transitioning status in response to rtpg requests. These requests get retried for a maximum of 60 seconds by default before timing out. Sometimes this timeout isn't sufficient to allow the array to complete the transition. T10-spc4 addresses this under 'Report Target Port Groups' command. This update retrieves the timeout value from the storage array if available and retries the transitioning rtpgs for up to the 'implied transitioning timeout' value Signed-off-by:
-
Dan Carpenter authored
ARCMSR_ARC1880_DiagWrite_ENABLE is 0x00000080 so (x | 0x00000080) is never zero. The intent here was to test that loop until ARCMSR_ARC1880_DiagWrite_ENABLE was turned on, but because the test was wrong, we would do five loops regardless of whether it succeed or not. Also I simplified the condition a little by removing the unused assignement. Signed-off-by:
Nick Cheng <nick.cheng@areca.com.tw> Signed-off-by:
-
HighPoint Linux Team authored
As the limitation of RR312x's dma engine, the HBA can not access host memory over 12GB. This fixes https://bugzilla.kernel.org/show_bug.cgi?id=14311 [alan: resurrected bug from 2009 and pushed upstream] Reported-by:
Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by:
HighPoint Linux Team <linux@highpoint-tech.com> Signed-off-by:
-
James Smart authored
Signed-off-by:
Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by:
James Smart <james.smart@emulex.com> Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Fix System Panic During IO Test using Medusa tool Signed-off-by:
-
James Smart authored
Fix fcp_imax module parameter to dynamically change FCP EQ delay multiplier Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Fixed system held-up when performing resource provsion through same PCI function Signed-off-by:
-
James Smart authored
Fix system hang due to bad protection module parameters (CR: 130769) Signed-off-by:
-
James Smart authored
Fixed debug helper routine failed to dump CQ and EQ entries in non-MSI-X mode Signed-off-by:
-
James Smart authored
This patch corrects the issue caught via Smatch and reported by Dan Carpenter: http://marc.info/?l=linux-scsi&m=133693516103343 Resolve null pointer check ordering that were odd Reported-by:
-
James Smart authored
Incorporate patch originally supplied by Julia Lawall <Julia.Lawall@lip6.fr> http://marc.info/?l=linux-scsi&m=133572879711140&w=2 "It appears that mempool_free should be performed on these failures as on the other exists from the containing functions." Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Acked-by:
-
Bhanu Prakash Gollapudi authored
Signed-off-by:
Bhanu Prakash Gollapudi <bprakash@broadcom.com> Signed-off-by:
-
Bhanu Prakash Gollapudi authored
Use list_for_each_entry_safe() instead of explicit cast to avoid relying on struct layout Signed-off-by:
-
Bhanu Prakash Gollapudi authored
During parity errors, the ramrods are not issued to FW. bnx2fc waits for the timeout value, and proceeds with cleaning up the IOs. Since we are already out-of-sync with FW, cleanup commands timeout too, and do not get the completion. This operation takes 36 secs for each session to upload causing huge delays. To fix this, bnx2fc now gets a PARITY_ERROR from cnic driver, and upon failure, the driver does not issue any commands to the FW and finishes the upload process sooner. Signed-off-by:
-
Mike Christie authored
We do not hold the host lock when calling these functions, so remove comment. Signed-off-by:
-
Mike Christie authored
This has scsi_internal_device_unblock/scsi_target_unblock take the new state to set the devices as an argument instead of always setting to running. The patch also converts users of these functions. This allows the FC and iSCSI class to transition devices from blocked to transport-offline, so that when fast_io_fail/replacement_timeout has fired we do not set the devices back to running. Instead, we set them to SDEV_TRANSPORT_OFFLINE. Signed-off-by:
-
Mike Christie authored
This patch adds a new state SDEV_TRANSPORT_OFFLINE. It will be used by transport classes to offline devices for cases like when the fast_io_fail/recovery_tmo fires. In those cases we want all IO to fail, and we have not yet escalated to dev_loss_tmo behavior where we are removing the devices. Currently to handle this state, transport classes are setting the scsi_device's state to running, setting their internal session/port structs state to something that indicates failed, and then failing IO from some transport check in the queuecommand. The reason for the new value is so that users can distinguish between a device failure that is a result of a transport problem vs the wide range of errors that devices get offlined for when a scsi command times out and we offline the devices there. It also fixes the confusion as to why the transport class is failing IO, but has set the device state from blocked to running. Signed-off-by:
-
Mark Rustad authored
Recent changes to add fcoe_sysfs caused libfcoe_init to call fcoe_transport_exit in a module initialization routine. The change resulted in the below error. This patch removes the __exit keyword from the fcoe_transport_exit definition such that it may be called from an __init routine. WARNING: drivers/scsi/fcoe/libfcoe.o(.init.text+0x21): Section mismatch in reference from the function init_module() to the function .exit.text:fcoe_transp exit() The function __init init_module() references a function __exit fcoe_transport_exit(). This is often seen when error handling in the init function uses functionality in the exit path. The fix is often to remove the __exit annotation of fcoe_transport_exit() so it may be used outside an exit section. Signed-off-by:
Mark Rustad <mark.d.rustad@intel.com> Signed-off-by:
Robert Love <robert.w.love@intel.com> Signed-off-by:
-
Bhanu Prakash Gollapudi authored
bnx2fc had an assumption that the fcoe interface will always start on the vlan dev. However, some switch implementations (Eg., HP virtual connect FlexFabric) expects the fcoe interface to be started on physical interface. Do not error out if the netdev is not a vlan dev. Signed-off-by:
-
Joe Perches authored
Deduplication of formats and consolidating tests makes the object much smaller. Add bnx2fc_debug.c, add functions for a few logging functions (BNX2FC_IO_DBG, BNX2FC_TGT_DBG, BNX2FC_HBA_DBG). Use printf extension %pV. Add and use pr_fmt and pr_<level>. Move the debug #include below structure definitions. $ size drivers/scsi/bnx2fc/built-in.o* text data bss dec hex filename 101563 1165 24976 127704 1f2d8 drivers/scsi/bnx2fc/built-in.o.new 138473 1109 33400 172982 2a3b6 drivers/scsi/bnx2fc/built-in.o.old Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Eric Dumazet authored
Since bnx2fc_percpu_thread_create() creates percpu kthread, it makes sense to use kthread_create_on_node() to get proper NUMA affinity for kthread stack. Signed-off-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
-
James Bottomley authored
scsi_wait_scan was introduced with asynchronous host scanning as a hack for distributions that weren't using proper udev based wait for root to appear in their initramfs scripts. In 2.6.30 Commit c7510859 Author: Rafael J. Wysocki <rjw@sisk.pl> Date: Sun Apr 12 20:06:56 2009 +0200 PM/Hibernate: Wait for SCSI devices scan to complete during resume Actually broke scsi_wait_scan because it renders scsi_complete_async_scans() a nop for modular SCSI if you include scsi_scans.h (which this module does). The lack of bug reports is sufficient proof that this module is no longer used. Cc: Jeff Mahoney <jeffm@suse.de> Cc: Dave Jones <davej@redhat.com> Cc: maximilian attems <max@stro.at> Signed-off-by:
-
Vasu Dev authored
Updates newly added stats from fc_get_host_stats, added new function fc_exch_update_stats to update exches related stats from fc_exch.c by going thru internal ema_list elements. Signed-off-by:
Vasu Dev <vasu.dev@intel.com> Acked-by : Robert Love <robert.w.love@intel.com> Tested-by:
Ross Brattain <ross.b.brattain@intel.com> Signed-off-by:
-
