The input terminal parser recurses into the referenced clock entity to verify
it is existant and thus the terminal descriptor is valid. The actual property
values of the term instance which is initially parsed must not be overriden by
the recursion. For this to work the term properties have to be assigned after
recursing into the referenced clock entity descriptors.
Signed-off-by: Julian Scheel <julian@jusst.de>
Acked-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Similar like the previous fix to hda_proc.c, adding const prefix will
save our world (a little bit).
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The power states in a proc file are printed in a racy manner on a
single static string buffer.  Fix it by calling snd_iprintf() directly
for each state instead of processing on a temporary buffer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Many arrays in hda_proc.c are string arrays that should be covered by
const prefix for increasing the safety and reducing the size.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

A few helper functions to convert the pin information to strings have
been exported with assumption that they were used by other drivers.
But they are referred only in the proc interface in the end.

Let's make them local so that we can get rid of a few exports.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The M-Audio Transit exposes an interface with a SYNC_NONE attribute.
This is not a valid value according to the USB audio classspec. However
there is a sync endpoint associated to this record. Changing the logic to
try to use this sync endpoint allows for seamless transitions between
altset 2 and altset 3. If any errors happen, the behavior remains the same.

$ more /proc/asound/card1/stream0
M-Audio Transit USB at usb-0000:00:14.0-2, full speed : USB Audio

Playback:
  Status: Stop
  Interface 1
    Altset 1
    Format: S24_3LE
    Channels: 2
    Endpoint: 3 OUT (ADAPTIVE)
    Rates: 48001 - 96000 (continuous)
  Interface 1
    Altset 2
    Format: S24_3LE
    Channels: 2
    Endpoint: 3 OUT (NONE)
    Rates: 8000 - 48000 (continuous)
  Interface 1
    Altset 3
    Format: S16_LE
    Channels: 2
    Endpoint: 3 OUT (ASYNC)
    Rates: 8000 - 48000 (continuous)
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When a transition occurs between alternate settings that do not use the
same synchronization method, the substream pointers were not reset.
This prevents audio from being played during the second transition.

Identified and tested with M-Audio Transit device
(0763:2006 Midiman M-Audio Transit)

Details of the issue:

First playback to adaptive endpoint:
$ aplay -Dhw:1,0 ~/24_96.wav
Playing WAVE '/home/plb/24_96.wav' : Signed 24 bit Little Endian in 3bytes,
Rate 96000 Hz, Stereo

[ 3169.297556] usb 1-2: setting usb interface 1:1
[ 3169.297568] usb 1-2: Creating new playback data endpoint #3
[ 3169.298563] usb 1-2: Setting params for ep #3 (type 0, 3 urbs), ret=0
[ 3169.298574] usb 1-2: Starting data EP @ffff880035fc8000

first playback to asynchronous endpoint:
$ aplay -Dhw:1,0 ~/16_48.wav
Playing WAVE '/home/plb/16_48.wav' : Signed 16 bit Little Endian,
Rate 48000 Hz, Stereo

[ 3204.520251] usb 1-2: setting usb interface 1:3
[ 3204.520264] usb 1-2: Creating new playback data endpoint #3
[ 3204.520272] usb 1-2: Creating new capture sync endpoint #83
[ 3204.521162] usb 1-2: Setting params for ep #3 (type 0, 4 urbs), ret=0
[ 3204.521177] usb 1-2: Setting params for ep #83 (type 1, 4 urbs), ret=0
[ 3204.521182] usb 1-2: Starting data EP @ffff880035fce000
[ 3204.521204] usb 1-2: Starting sync EP @ffff8800bd616000

second playback to adaptive endpoint: no audio and error on terminal:
$ aplay -Dhw:1,0 ~/24_96.wav
Playing WAVE '/home/plb/24_96.wav' : Signed 24 bit Little Endian in 3bytes,
Rate 96000 Hz, Stereo
aplay: pcm_write:1939: write error: Input/output error

[ 3239.483589] usb 1-2: setting usb interface 1:1
[ 3239.483601] usb 1-2: Re-using EP 3 in iface 1,1 @ffff880035fc8000
[ 3239.484590] usb 1-2: Setting params for ep #3 (type 0, 4 urbs), ret=0
[ 3239.484606] usb 1-2: Setting params for ep #83 (type 1, 4 urbs), ret=0

This last line shows that a sync endpoint is used when it shouldn't.
The sync endpoint is no longer valid and the pointers are corrupted
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

USB Audio Class version 2.0 supports three different parameter block sizes for
CUR requests, which are 1 byte (5.2.3.1 Layout 1 Parameter Block), 2 bytes
(5.2.3.2 Layout 2 Parameter Block) and 4 bytes (5.2.3.3 Layout 3 Parameter
Block). Use the correct size according to the specific control as it was
already done for UACv1. The allocated block size for control requests is
increased to support the 4 byte worst case.
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Alienware 15 has CA0132 codec for its onboard sound, but the pin
config and mapping seem quite different from other Creative boards.
This patch corrects them, at least, for providing the right headphone
and mic jack notification, as well as removing the non-existing SPDIF
pins.

Even with this fix, not all stuff works perfectly yet, mainly because
of the badly written ca0132 driver code -- it has too many implicit
assumptions of pin configs and maps.  Nevertheless, this is a small
good step forward.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=101981Signed-off-by: Takashi Iwai <tiwai@suse.de>

The echoaudio locally defines TRUE and FALSE.  Not only is this
redundant given that C now has a boolean type it results in lots of
warnings as other headers also define these macros, causing duplicate
definitions.  Fix this by removing the local defines and converting all
local users to use the standard C true and false instead, simply
removing the macros is less safe due to implicit inclusion of the other
definitons.

[fixed overlooked replacement of FALSE by tiwai]
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The patch was generated using fixed coccinelle semantic patch
scripts/coccinelle/api/memdup.cocci [1].

[1]: http://permalink.gmane.org/gmane.linux.kernel/2014320Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Merge tag 'asoc-fix-v4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v4.2

There are a couple of small driver specific fixes here but the
overwhelming bulk of these changes are fixes to the topology ABI that
has been newly introduced in v4.2.  Once this makes it into a release we
will have to firm this up but for now getting enhancements in before
they've made it into a release is the most expedient thing.

Merge remote-tracking branches 'asoc/fix/cs4265', 'asoc/fix/intel' and 'asoc/fix/topology' into asoc-linus

Add ID for standalone private data object types and bump ABI version to
3 in order to userpsace features.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add UAPI support for setting byte control ops. Rename the ops structure
to be more generic so it can be sued by other objects too.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Currently the TLV topology structure is targeted at only supporting the
DB scale data. This patch extends support for the other TLV types so they
can be easily added at a later stage.

TLV structure is moved to common topology control header since it's a
common field for controls and can be processed in a general way.

Users must set a proper access flag for a control since it's used to
decide if the TLV field is valid and if a TLV callback is needed.

Removed the following fields from topology TLV struct:
- size/count: type can decide the size.
- numid: not needed to initialize TLV for kcontrol.
- data: replaced by the type specific struct.

Added TLV structure to generic control header and removed TLV structure
from mixer control.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Fixes for v4.2

A lot of small fixes here, a few to the core:

 - Fix for binding DAPM stream widgets on devices with prefixes assigned
   to them
 - Minor fixes for the newly added topology interfaces
 - Locking and memory leak fixes for DAPM
 - Driver specific fixes

The topology file manifest should include a private data field. This
allows vendors to specify vendor data in the manifest, like
timestamps, hashes, additional information for removing platform
configuration out of drivers and making these configurable per platform
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Some widgets may need sorting within, So add this support in topology.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Update the aoa-soundbus framework to use dev_pm_ops rather than the
deprecated legacy suspend and resume callbacks.

Since there isn't anything special to do at the bus level the bus driver
does not have to implement any callbacks. The device driver core will
automatically pick up and execute the device's PM ops.

As there is only a single aoa-soundbus driver implementing suspend and
resume, update both the core and driver at the same time to avoid
unnecessary code churn.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

It turned out that there are three variants of pin config values of
NID 0x17 on Dell laptops with ALC3266 (alias of ALC298): 0x90170110,
0x90170140 and 0x90170150.  The first two have been already covered by
commits 703867e2 and 977e6276, so this commit adds the missing
last entry.

While we're at it, rearrange the three entries in the order of pincfg
values.
Reported-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The fixup ALC292_FIXUP_DISABLE_AAMIX can fix the white noise of
the headphone on this Dell machine.

Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Fireworks uses TSB43CB43(IceLynx-Micro) as its IEC 61883-1/6 interface.
This chip includes ARM7 core, and loads and runs program. The firmware
is stored in on-board memory and loaded every powering-on from it.

Echo Audio ships several versions of firmwares for each model. These
firmwares have each quirk and the quirk changes a sequence of packets.

As long as I investigated, AudioFire2/AudioFire4/AudioFirePre8 have a
quirk to transfer a first packet with 0x02 in its dbc field. This causes
ALSA Fireworks driver to detect discontinuity. In this case, firmware
version 5.7.0, 5.7.3 and 5.8.0 are used.

Payload  CIP      CIP
quadlets header1  header2
02       00050002 90ffffff <-
42       0005000a 90013000
42       00050012 90014400
42       0005001a 90015800
02       0005001a 90ffffff
42       00050022 90019000
42       0005002a 9001a400
42       00050032 9001b800
02       00050032 90ffffff
42       0005003a 9001d000
42       00050042 9001e400
42       0005004a 9001f800
02       0005004a 90ffffff
(AudioFire2 with firmware version 5.7.)

$ dmesg
snd-fireworks fw1.0: Detect discontinuity of CIP: 00 02

These models, AudioFire8 (since Jul 2009 ) and Gibson Robot Interface
Pack series uses the same ARM binary as their firmware. Thus, this
quirk may be observed among them.

This commit adds a new member for AMDTP structure. This member represents
the value of dbc field in a first AMDTP packet. Drivers can set it with
a preferred value according to model's quirk.
Tested-by: Johannes Oertei <johannes.oertel@uni-due.de>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This reverts commit 9c6893e0.

The fix is superseded by the next commit as a better implementation
for supporting AudioFire2/AudioFire4/AudioFirePre8 quirks.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The new Dell laptop with ALC3266 can't use internal microphone to
record. Also, the 3 ring headset mic doesn't work on it. For src of
patch_realtek.c, only the pin cfg of Nid 0x17 is different, so the
Nid 0x17 is added into pin quirk, and others are defined to macro
ALC298_STANDARD_PINS in common use.

Codec: Realtek ALC3266
Vendor Id: 0x10ec0298
Subsystem Id: 0x102806e5

BugLink: https://bugs.launchpad.net/bugs/1481575Signed-off-by: Woodrow Shen <woodrow.shen@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The snd_hdac_chip_readl return can never be less than zeros,
so no point in checking for the return value

This fixes following static checker warnings in
snd_hdac_ext_bus_parse_capabilities

       sound/hda/ext/hdac_ext_controller.c:47
 snd_hdac_ext_bus_parse_capabilities()
       warn: unsigned 'offset' is never less than zero.

       sound/hda/ext/hdac_ext_controller.c:54
 snd_hdac_ext_bus_parse_capabilities()
       warn: unsigned 'cur_cap' is never less than zero.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This fixes issue in assigning host stream in case of
decoupled mode. The check to verify if the stream is already
in use was wrong so fix that
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

I2S2_DAC pin can be used for I2S or GPIO. We should set it as GPIO
if we use GPIO5 as DMIC1 data pin.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

To cleanup the pin_quirk table:
 - rewrite the pin_config_match(), comparing all pins on the machine
   with the corresponding pins in the quirk table.
 - remove all 0x4xxxxxxx pin configurations from pin_quirk table
 - after removing the 0x4xxxxxxx pin configurations, some pin tables
   are exactly same, so removing the redudant pin tables.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This fixes the following warning, that is seen with gcc 5.1:
warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses].
Signed-off-by: Tomer Barletz <barletz@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Pull powerpc fixes from Michael Ellerman:
 - TCE table memory calculation fix from Alexey
 - Build fix for ans-lcd from Luis
 - Unbalanced IRQ warning fix from Alistair

* tag 'powerpc-4.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/eeh-powernv: Fix unbalanced IRQ warning
  macintosh/ans-lcd: fix build failure after module_init/exit relocation
  powerpc/powernv/ioda2: Fix calculation for memory allocated for TCE table

Ted Ts'o reports that his Lenovo T540p ThinkPad crashes at boot if
attached to the docking station.  This is a regression that he was able
to bisect to commit 8c7b5ccb: "drm/i915: Use atomic helpers for
computing changed flags:"

The reason seems to be the new call to drm_atomic_helper_check_modeset()
added to intel_modeset_compute_config(), which in turn calls
update_connector_routing(), and somehow ends up picking a NULL crtc for
the connector state, causing the subsequent drm_crtc_index() to OOPS.

Daniel Vetter says that the fundamental issue seems to be confusion in
the encoder selection, and this isn't the right fix, but while he chases
down the proper fix, this at least avoids the NULL pointer dereference
and makes Ted's docking station work again.
Reported-bisected-and-tested-by: Theodore Ts'o <tytso@mit.edu>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Mani Nikula <jani.nikula@linux.intel.com>
Cc: Dave Airlie <airlied@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull SCSI fixes from James Bottomley:
 "A set of three fixes for the ipr driver and one fairly major one for
  memory leaks in the mq path of SCSI"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: fix memory leak with scsi-mq
  ipr: Fix invalid array indexing for HRRQ
  ipr: Fix incorrect trace indexing
  ipr: Fix locking for unit attention handling

Pull ARM SoC fixes from Olof Johansson:
 "Things are calming down nicely here w.r.t. fixes.  This batch
  includes two week's worth since I missed to send before -rc4.

  Nothing particularly scary to point out, smaller fixes here and there.
  Shortlog describes it pretty well"

* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: dts: keystone: fix dt bindings to use post div register for mainpll
  ARM: nomadik: disable UART0 on Nomadik boards
  ARM: dts: i.MX35: Fix can support.
  ARM: OMAP2+: hwmod: Fix _wait_target_ready() for hwmods without sysc
  ARM: dts: add CPU OPP and regulator supply property for exynos4210
  ARM: dts: Update video-phy node with syscon phandle for exynos3250
  ARM: DRA7: hwmod: fix gpmc hwmod

Pull VFS fix from Al Viro:
 "Spurious ENOTDIR fix"

This should fix the problems reported by Dominique Martinet and Hugh
Dickins.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  link_path_walk(): be careful when failing with ENOTDIR

In RCU mode we might end up with dentry evicted just we check
that it's a directory.  In such case we should return ECHILD
rather than ENOTDIR, so that pathwalk would be retries in non-RCU
mode.

Breakage had been introduced in commit b18825a7 - prior to that
we were looking at nd->inode, which had been fetched before
verifying that ->d_seq was still valid.  That form of check
would only be satisfied if at some point the pathname prefix
would indeed have resolved to a non-directory.  The fix consists
of checking ->d_seq after we'd run into a non-directory dentry,
and failing with ECHILD in case of mismatch.

Note that all branches since 3.12 have that problem...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>