Merge tag 'omap-for-v4.12/dt-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

Pull "Devicetree changes for omaps for v4.12 merge window" from Tony Lindgren:

- Add hecc node for am35x

- Add onenand support for omap3-igep

- Add bluetooth binding for n900/n9/n950

- Configure clocks and SATA for dm81xx

- Update operating points tables for am33xx, am43xx and dra7

- Update SPI flash documentation for w25q64

- Configure SPI NOR for am335x-icev2

- Mux uart0 for am437x-gp-evm

- Add thermal zones for omap3, omap4, omap5, dra7

- Configure LEDs for am335x-baltos

- A series of droid 4 changes to configure various devices
  such as keypad, regulators, gpio-keys, rtc, power button,
  compass, accelerometer, touchscreen, backlight, poweroff,
  tmp105, HDMI, LCD panel and LEDs, EHCI, and micro-SD

* tag 'omap-for-v4.12/dt-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (35 commits)
  ARM: dts: am335x-baltos: add LED support
  ARM: dts: omap4-droid4: Fix MMC1 card for detect GPIO and regulator
  ARM: dts: OMAP4460: Thermal: Add slope and offset values
  ARM: dts: OMAP443x: Thermal: Add slope and offset values
  ARM: dts: OMAP5: Thermal: Add slope and offset values
  ARM: dts: DRA7: Thermal: Add slope and offset values
  ARM: dts: omap3: Add cpu_thermal zone
  ARM: dts: am437x-gp-evm: Add pinmux for uart0
  ARM: dts: am335x-icev2: Add SPI based NOR
  Documentation: devicetree: mtd: add w25q64 to list of supported SPI flashes
  ARM: dts: dra7: Add updated operating-points-v2 table for cpu
  ARM: dts: am4372: Update operating-points-v2 table for cpu
  ARM: dts: am335x-boneblack: Enable 1GHz OPP for cpu
  ARM: dts: am33xx: Add updated operating-points-v2 table for cpu
  ARM: dts: dm8168-evm: add SATA node
  ARM: dts: dm8168-evm: add the external reference clock for SATA
  ARM: dts: N9/N950: add bluetooth
  ARM: dts: N900: Add bluetooth
  ARM: dts: omap4-droid4: Configure EHCI so modems can be accessed
  ARM: dts: motorola-cpcap-mapphone: add LEDs
  ...

Merge tag 'v4.12-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

Pull "Rockchip dts32 updates for 4.12 part1" from Heiko Stübner:

Contains one new board, the Tinkerboard from Asus based on the rk3288,
definitions for the mmc resets in the socs reset controller, sound
support for the Rock2, dma support for mmc controllers on the rk3188
and a led-fix for the MiQi board and and irq-fix for older Cortex-A9 socs.

* tag 'v4.12-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: setup DMA-channels for mmc0 and emmc for rk3188
  ARM: dts: rockchip: fix PPI misconfiguration on Cortex-A9 socs
  ARM: dts: rockchip: add rk322x dw-mmc resets
  ARM: dts: rockchip: add rk3066/rk3188 dw-mmc resets
  ARM: dts: rockchip: add rk3036 dw-mmc resets
  ARM: dts: rockchip: add rk3288 dw-mmc resets
  ARM: dts: rockchip: add dts for RK3288-Tinker board
  dt-bindings: add rk3288-based Asus Tinker board
  ARM: dts: rockchip: fix the MiQi board's LED definition
  ARM: dts: rockchip: Add support for ES8388 to the Radxa Rock 2

Merge tag 'gemini-dts-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt

Pull "DTS updates for the Gemini on top of the multiplatform base" from Linus Walleij:

- Add the power controller to the DTS.
- Augment the GPIO nodes to also include the Faraday
  compatible.
- Add the PCI bus host and config to the Gemini device trees.

* tag 'gemini-dts-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
  ARM: dts: add PCI to the Gemini device trees
  ARM: dts: augment Gemini GPIO nodes
  ARM: dts: add power controller to the Gemini DTS

Pull "Broadcom devicetree changes for 4.12" from Florian Fainelli:

This pull request contains Broadcom ARM-based SoCs Device Tree updates for
4.12, please pull the following:

- Rafal:

	* adds basic support for the Linksys EA9200, Linksys EA6300 V1, Linksys
	  EA9500, TP-Link Archer C5 V2 which are all based on BCM470x SoCs with
	  a bunch of BCM43602 radios.

	* updates the BCM5301X DTS and DTS include file and moves the serial
	  console parameters to the DTS include file since all BCM5301X that we have so
	  far are consistent in using the same UART. He also does the same for the
	  BCM53573 DTS.

	* makes some updates to the Tenda AC9 platform by describing its
	  PCIe controllers and endpoints in order to be able to represent GPIOs attached
	  to the on-chip Wi-Fi module. Once done, he adds the 2Ghz LED which is connected
	  to one of these GPIOs.

	* re-licenses the DTS files he created to the ISC license

	* removes the use of the non-existend "default-off" LED trigger in the
	  BCM53573 and BCM5301X DTS files

- Aditya adds missing Netgear R8000 LEDS and keys for WAN status LEDS and brightness

- Jon:
	* adds NAND controller Device Tree nodes to the BCM953012K reference board

  	* converts the BCM5301X SoC to use the recently introduced Broadcom QSPI controller
  	  Device Tree nodes.

	* fixes the GIC PPI interrupt flags that the kernel now
  	  reports about.

	* adds ARM TWD watchdog entries to the BCM5301X DTS include file
  	* adds I2C entries to the BCM5301X DTS include files.

	* disables i2c by default in the Northstar Plus DTS include file, and
	 ,enables it at the board level instead.

	* adds USB (OHCI & EHCI) Device Tree nodes to the Northstar Plus DTS
	  include files.

- Steven adds the mailbox (PDC) unit and the crytographic unit (SPU) to the
  Broadcom Northstar Plus SoC DTS include file. Steven also adds proper ethernet
  aliases to the BCM53012HR board since some bootloaders require that for MAC address
  patching.

- Eric adds the DSI and its corresponding clock nodes to the BCM283x DTS files
  but leaves them disabled by default (overlays should take care of enabling it)

- Boris adds support for HDMI audio and related DMA channels to the BCM283x SoCs

- Gerd adds support for the BCM2835 specific SDHCI controller to the BCM283x SoCs

- Rob fixes the iProc msi-controller name and unit address now that DTC can produce
  additional errors

* tag 'arm-soc/for-4.12/devicetree' of http://github.com/Broadcom/stblinux: (27 commits)
  ARM: dts: bcm: fix msi-controller name and unit address
  ARM: dts: BCM53573: Specify serial console parameters
  ARM: dts: BCM5301X: Specify serial console params in dtsi files
  ARM: dts: NSP: Add crypto (SPU) to dtsi
  ARM: dts: NSP: Add mailbox (PDC) to NSP
  ARM: dts: BCM953012HR: Add ethernet aliases
  ARM: dts: BCM5301X: Add support for TP-LINK Archer C5 V2
  ARM: dts: NSP: disable i2c DT entry by default
  ARM: dts: NSP: Add EHCI/OHCI USB nodes to device tree
  ARM: dts: BCM5301X: Add I2C support to the DT
  ARM: dts: BCM5301X: Add TWD WD Support to DT
  ARM: dts: BCM5301X: Correct GIC_PPI interrupt flags
  ARM: dts: bcm2835: add sdhost controller to devicetree
  ARM: dts: bcm283x: Add HDMI audio related properties
  ARM: dts: BCM5301X: Don't use nonexistent "default-off" LED trigger
  ARM: dts: BCM53573: Don't use nonexistent "default-off" LED trigger
  ARM: dts: BCM5301X: Add missing Netgear R8000 LEDs and Keys
  ARM: dts: BCM5301X: Relicense DTS files I created to the ISC
  ARM: dts: bcm2835: Add the DSI module nodes and clocks.
  ARM: dts: BCM53573: Add Tenda AC9 2 GHz LED
  ...

Pull "mvebu dt for 4.12 (part 1)" from Gregory CLEMENT:

- Add node lable for Armada 38x
- Add support for Synology DS116 NAS and Linksys WRT1900ACS
- Update mbus controller description on Armada 38x allowing entering in standby
- Add default trigger for sata led on various linksys boards
- Update newly added armada-xp-98dx3236
- Enable hardware buffer manager support for the devices in the
  Linksys WRT AC Serie

* tag 'mvebu-dt-4.12-1' of git://git.infradead.org/linux-mvebu:
  ARM: dts: mvebu: linksys: enable buffer manager support
  ARM: dts: mvebu: remove unnecessary PCI range from 98dx3236
  ARM: dts: mvebu: Move mv98dx3236 clock bindings
  ARM: dts: Use armada-370-xp as a base for armada-xp-98dx3236
  ARM: dts: armada-xp-98dx3236: combine dfx server nodes
  ARM: dts: armada: Add default trigger for sata led
  ARM: dts: armada-38x: Adjust mbus controller description on Armada 38x
  ARM: dts: armada-385: add support for the Linksys WRT1900ACS (Shelby)
  ARM: dts: armada-385-synology-ds116: add support for Synology DS116 NAS
  ARM: dts: armada-38x add node labels

Merge tag 'davinci-for-v4.12/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt

Pull "DaVinci DT updates for v4.12" from Sekhar Nori:

DaVinci device tree updates to enable
Video display on DA850 along with some
whitespace clean-up.

Also, enables sound and ADC support on
Lego EV3.

* tag 'davinci-for-v4.12/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
  ARM: dts: da850-evm: add the output port to the vpif node
  ARM: dts: da850-evm: add IO expander node on UI card
  ARM: dts: da850: add vpif video display pins
  ARM: dts: da850-evm: fix whitespace errors
  ARM: da850-lego-ev3: Add device tree node for sound
  ARM: da850-lego-ev3: Add device tree node for A/DC

The Moxa ART GPIO is a Faraday FTGPIO010. Augment the DTS node
to indicate both compatible values for the SoC and the IP part.
Also increase the register range to 0x100, it has at least 0x48
bytes of registers, and a few extra will not hurt.
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'uniphier-dt-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt

Pull "UniPhier ARM SoC DT updates for v4.12" from Masahiro Yamada:

- Remove skeleton.dtsi inclusion
- Fix W=* build warnings
- Fix eMMC pin-mux node
- Add pagesize properties to EEPROM nodes

* tag 'uniphier-dt-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
  ARM: dts: uniphier: add pagesize property to EEPROM of proto boards
  ARM: dts: uniphier: add pagesize property to EEPROM of Support Card
  ARM: dts: uniphier: fix pin groups of eMMC pin-mux node
  ARM: dts: uniphier: move memory node below aliases node
  ARM: dts: uniphier: fix no unit name warnings
  ARM: dts: uniphier: remove skeleton.dtsi inclusion

All three devices provide GPIO based LEDs named power,
wlan and app.

Place LEDs definition into a separate dtsi file as not all
devices including am335x-baltos.dtsi have the same LED layout.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

There's a typo, it should be GPIO176 and not GPIO106.

And it seems I messed up the regulators at some point while trying
to figure out what devices the regulators are used. The correct
regulator for MMC1 is vwlan2.

Fixes: 0d4cb3cc ("ARM: dts: Configure regulators for droid 4")
Reported-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The Cortina Gemini has an internal PCI root bus, add this to
the device tree, and add interrupt mapping (swizzling) to the
relevant systems device trees.

Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Feng-Hsin Chiang <john453@faraday-tech.com>
Cc: Greentime Hu <green.hu@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This pull request brings in the DT nodes for enabling HDMI audio on
Raspberry Pi, and nodes to describe the DSI and SDHOST hardware
modules (which are still disabled by default).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add cpu_thermal zone.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add pinmux for rx,tx,cts and rts lines of uart0. This will enable uart0
to use hardware flow control.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enable support for W25Q64CVSSIG which is a Winbond 64 Mbit SPI NOR.

At boot you will see the following message:
m25p80 spi1.0: found s25fl064k, expected w25q64

This is because the JEDEC ID for this chip is the same as s25fl064k.
However, this should be harmless since both chips are essentially the
same.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

W25Q64 is found on TI's AM335x ICEv2 board. Add it to list
for supported SPI flash devices. This flash can be identified
using JEDEC READ ID opcode.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

After the ti-cpufreq driver has been added, we can now drop the
operating-points table present in dra7.dtsi for the cpu and add an
operating-points-v2 table with all OPPs available for all silicon
revisions. Also add necessary data for use by ti-cpufreq to selectively
enable the appropriate OPPs at runtime as part of the operating-points
table.

As we now need to define voltage ranges for each OPP, we define the
minimum and maximum voltage to match the ranges possible for AVS class0
voltage as defined by the DRA7/AM57 Data Manual, with the exception of
using a range for OPP_OD based on historical data to ensure that SoCs
from older lots still continue to boot, even though more optimal voltages
are now the standard. Once an AVS Class0 driver is in place it will be
possible for these OPP voltages to be adjusted to any voltage within the
provided range.

Information from SPRS953, Revised December 2015.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The operatings-points-v2 table for am4372 was merged before any user of
it was present in the kernel and before the binding had been finalized.
The new ti-cpufreq driver and binding expects the platform specific
properties to be part of the operating-points-v2 table rather than the
cpu node so let's move them there as the only user is the ti-cpufreq
driver.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Although all PG2.0 silicon may not support 1GHz OPP for the MPU, older
Beaglebone Blacks may have PG2.0 silicon populated and these particular
parts are guaranteed to support the OPP, so enable it for PG2.0 on
am335x-boneblack only.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

After the ti-cpufreq driver has been added, we can now drop the
operating-points table present in am33xx.dtsi for the cpu and add an
operating-points-v2 table with all OPPs available for all silicon
revisions. Also add necessary data for use by ti-cpufreq to selectively
enable the appropriate OPPs at runtime as part of the operating-points
table.

Information from AM335x Data Manual, SPRS717i, Revised December 2015,
Table 5-7.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add the SATA controller node to the dm8168-evm device tree.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This board has an external oscillator supplying the reference clock
signal for SATA. Its rate is fixed at 100Mhz. Add a corresponding
device tree node.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add appropriate properties to devices in the Linksys WRT AC Series for the
mvneta driver to use hardware buffer management.

Also update "soc" ranges property and set the status of bm and bm-bppi
to "okay" (SRAM).
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

The Nokia N950 and N9 have a wl1271 (with nokia bootloader) bluetooth
module connected to second UART.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add bcm2048 node and its system clock to the N900 device tree file.
Apart from that a reference to the new clock has been added to
wl1251 (which uses it, too).
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The unit address for the msi controller is not valid as there is no reg
property, so remove it. Also, msi-controller is the preferred node name.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Jon Mason <jonmason@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

This adds baud rate, parity & number of data bits. It's required to get
serial working correctly.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

So far every Northstar device we have seen was using the same serial
console params (115200n8). It probably make the most sense to put it in
some proper dtsi files instead of repeating over and over for every
single device. As different boards may use different bootloaders it
seems the safest idea is to use board specific dtsi files.

Just in case some vendor decides to use different UART (parameters) this
can be always easily overwritten.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Droid 4 has two modems, mdm6600 and w3glte. Both are on the HCI USB
controller.

Let's add a configuration for the HCI so the modems can be enabled.

Note that the modems still need additional GPIO based configuration.

Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
[tony@atomide.com: left out url]
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add LEDs.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The LCD panel on droid 4 is a command mode LCD. The binding follows
the standard omapdrm binding and the changes needed for omapdrm command
mode panels are posted separately.

Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can get HDMI working as long as the 5V regulator is on. There is
probably an encoder chip there too, but so far no idea what it might be.
Let's keep the 5V HDMI regulator always enabled for now as otherwise we
cannot detect the monitor properly.

Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add tmp105 sensor for droid 4. This can be used with modprobe
lm75.ko and running sensors from lm-sensors package. Note that
the lm75.c driver does not yet support alert interrupt but
droid 4 seems to be wired for it.

Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Droid 4 has a GPIO line that we can use with CONFIG_POWER_RESET_GPIO.
It is probably connected to the CPCAP PMIC, and seems to power down
the whole device taking power consumption to zero based on what
I measured.

Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The TI LMU driver has not yet been merged, but the device
tree binding for TI LMU drivers has been acked already
earlier by Rob Herring <robh+dt@kernel.org>. So it should
be safe to apply to cut down the number of pending patches.

Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Milo Kim <milo.kim@ti.com>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>