There is a HW bug in Skylake, and Broxton PCH Intel PTT device, where
most of the registers in the control area except START, REQUEST, CANCEL,
and LOC_CTRL lost retention when the device is in the idle state. Hence
we need to bring the device to ready state before accessing the other
registers. The fix brings device to ready state before trying to read
command and response buffer addresses in order to remap the for access.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinn@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinn@linux.intel.com>

The register TPM_CRB_CTRL_REQ_x contains bits goIdle and cmdReady for
SW to indicate that the device can enter or should exit the idle state.

The legacy ACPI-start (SMI + DMA) based devices do not support these
bits and the idle state management is not exposed to the host SW.
Thus, this functionality only is enabled only for a CRB start (MMIO)
based devices.

Based on Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
original patch:
'tpm_crb: implement power tpm crb power management'

To keep the implementation local to the hw we don't use wait_for_tpm_stat
for polling the TPM_CRB_CTRL_REQ.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

tpm_transmit() does not check that bufsiz is at least TPM_HEADER_SIZE
before accessing data. This commit adds this check and returns -EINVAL
if it fails.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Constify TPM 1.x header structures in order to move them to rodata
section as they are meant to be never changed during runtime.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Because of the line break in the debug print the chackpatch is
not silent on 80 characters limitation.

The easiest fix is to straighten the lines, it's also more readable.

WARNING: line over 80 characters
+                       FW_BUG "TPM2 ACPI table does not define a memory
resource\n");
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Don't apply endianity conversion when writing to the registers
this is already handled by the system.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Instead of expensive register access on retrieving cmd_size
on each send, save the value during initialization in the private
context. The value doesn't change.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

The platform device is not used in this driver, drop the
include to linux/platform_device.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Fixes the warning:
drivers/char/tpm/tpm_tis_core.c:443:7: warning: variable ‘itpm’ set but
not used [-Wunused-but-set-variable]
  bool itpm;
       ^~~~
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

CRB_CTRL_CMD_READY and CRB_CTRL_GO_IDLE have incorrect values.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Renamed CRB protocol specific constants to match the TCG PC Client
Platform TPM Profile (PTP) Specification and driver status constants
to be explicit that they are driver specific.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

wmb()'s are not needed as iowrite32() is used.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

The req_canceled() callback is used by tpm_transmit() periodically to
check whether the request has been canceled while it is receiving a
response from the TPM.

The TPM_CRB_CTRL_CANCEL register was cleared already in the crb_cancel
callback, which has two consequences:

* Cancel might not happen.
* req_canceled() always returns zero.

A better place to clear the register is when starting to send a new
command. The behavior of TPM_CRB_CTRL_CANCEL is described in the
section 5.5.3.6 of the PTP specification.

CC: stable@vger.kernel.org
Fixes: 30fc8d13 ("tpm: TPM 2.0 CRB Interface")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Instead of a ad-hoc protocol message construction it is better to
call tpm_pcr_read_dev().
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>

It is better to tpm_transmit_cmd() in tpm2_probe() in order to get
consistent command handling throughout the subsystem.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>

Since tpm_gen_interrupt() is only used in tpm_tis_core.c this commit
replaces it with an internal tpm_tis_gen_interrupt(). The semantics
also changed in a way that on a system error the driver initialization
is failed.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>

Removed unnecessary externs from tpm.h.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>

This function should only be called as part of an IRQ probing protocol
and st33 does not have any code to detect that the IRQ it tries to
generate was not generated and disable the IRQ.

Since st33 is primarily a DT binding driver it should not be doing
IRQ probing anyhow, so let us just delete this useless call.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Unseal and load operations should be done as an atomic operation. This
commit introduces unlocked tpm_transmit() so that tpm2_unseal_trusted()
can do the locking by itself.

Fixes: 0fe54803 ("keys, trusted: seal/unseal with TPM 2.0 chips")
Cc: stable@vger.kernel.org
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>

The driver emits invalid self test error message even though the init
succeeds.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Fixes: cae8b441 ("tpm: Factor out common startup code")
Reviewed-by: James Morris <james.l.morris@oracle.com>

Under a strict subject/object security policy delivering a
signal or delivering network IPC could be considered either
a write or an append operation. The original choice to make
both write operations leads to an issue where IPC delivery
is desired under policy, but delivery of signals is not.
This patch provides the option of making signal delivery
an append operation, allowing Smack rules that deny signal
delivery while allowing IPC. This was requested for Tizen.
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>

Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>

Fixes: 8112c4f1 ("seccomp: remove 2-phase API")
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>

Update the syscall number after each PTRACE_SETREGS on ORIG_*AX.

This is needed to get the potentially altered syscall number in the
seccomp filters after RET_TRACE.

This fix four seccomp_bpf tests:
> [ RUN      ] TRACE_syscall.skip_after_RET_TRACE
> seccomp_bpf.c:1560:TRACE_syscall.skip_after_RET_TRACE:Expected -1 (18446744073709551615) == syscall(39) (26)
> seccomp_bpf.c:1561:TRACE_syscall.skip_after_RET_TRACE:Expected 1 (1) == (*__errno_location ()) (22)
> [     FAIL ] TRACE_syscall.skip_after_RET_TRACE
> [ RUN      ] TRACE_syscall.kill_after_RET_TRACE
> TRACE_syscall.kill_after_RET_TRACE: Test exited normally instead of by signal (code: 1)
> [     FAIL ] TRACE_syscall.kill_after_RET_TRACE
> [ RUN      ] TRACE_syscall.skip_after_ptrace
> seccomp_bpf.c:1622:TRACE_syscall.skip_after_ptrace:Expected -1 (18446744073709551615) == syscall(39) (26)
> seccomp_bpf.c:1623:TRACE_syscall.skip_after_ptrace:Expected 1 (1) == (*__errno_location ()) (22)
> [     FAIL ] TRACE_syscall.skip_after_ptrace
> [ RUN      ] TRACE_syscall.kill_after_ptrace
> TRACE_syscall.kill_after_ptrace: Test exited normally instead of by signal (code: 1)
> [     FAIL ] TRACE_syscall.kill_after_ptrace

Fixes: 26703c63 ("um/ptrace: run seccomp after ptrace")
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: James Morris <jmorris@namei.org>
Cc: user-mode-linux-devel@lists.sourceforge.net
Signed-off-by: James Morris <james.l.morris@oracle.com>

Keep the same semantic as before the commit 26703c63: deallocate
audit context and fake a proper syscall exit.

This fix a kernel panic triggered by the seccomp_bpf test:
> [ RUN      ] global.ERRNO_valid
> BUG: failure at kernel/auditsc.c:1504/__audit_syscall_entry()!
> Kernel panic - not syncing: BUG!

Fixes: 26703c63 ("um/ptrace: run seccomp after ptrace")
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: James Morris <jmorris@namei.org>
Cc: user-mode-linux-devel@lists.sourceforge.net
Signed-off-by: James Morris <james.l.morris@oracle.com>

Remove remaining kernel_module_from_file hook left by commit
a1db7420 ("module: replace copy_module_from_fd with kernel version")
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>

Pull more block fixes from Jens Axboe:
 "As mentioned in the pull the other day, a few more fixes for this
  round, all related to the bio op changes in this series.

  Two fixes, and then a cleanup, renaming bio->bi_rw to bio->bi_opf.  I
  wanted to do that change right after or right before -rc1, so that
  risk of conflict was reduced.  I just rebased the series on top of
  current master, and no new ->bi_rw usage has snuck in"

* 'for-linus' of git://git.kernel.dk/linux-block:
  block: rename bio bi_rw to bi_opf
  target: iblock_execute_sync_cache() should use bio_set_op_attrs()
  mm: make __swap_writepage() use bio_set_op_attrs()
  block/mm: make bdev_ops->rw_page() take a bool for read/write

Pull drm zpos property support from Dave Airlie:
 "This tree was waiting on some media stuff I hadn't had time to get a
  stable branchpoint off, so I just waited until it was all in your tree
  first.

  It's been around a bit on the list and shouldn't affect anything
  outside adding the generic API and moving some ARM drivers to using
  it"

* tag 'drm-for-v4.8-zpos' of git://people.freedesktop.org/~airlied/linux:
  drm: rcar: use generic code for managing zpos plane property
  drm/exynos: use generic code for managing zpos plane property
  drm: sti: use generic zpos for plane
  drm: add generic zpos property

Since commit 63a4cc24, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.

No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>

The original commit missed this function, it needs to mark it a
write flush.

Cc: Mike Christie <mchristi@redhat.com>
Fixes: e742fc32 ("target: use bio op accessors")
Signed-off-by: Jens Axboe <axboe@fb.com>

Cleaner than manipulating bio->bi_rw flags directly.
Signed-off-by: Jens Axboe <axboe@fb.com>

Commit abf54548 changed it from an 'rw' flags type to the
newer ops based interface, but now we're effectively leaking
some bdev internals to the rest of the kernel. Since we only
care about whether it's a read or a write at that level, just
pass in a bool 'is_write' parameter instead.

Then we can also move op_is_write() and friends back under
CONFIG_BLOCK protection.
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>

Pull documentation fixes from Jonathan Corbet:
 "Three fixes for the docs build, including removing an annoying warning
  on 'make help' if sphinx isn't present"

* tag 'doc-4.8-fixes' of git://git.lwn.net/linux:
  DocBook: use DOCBOOKS="" to ignore DocBooks instead of IGNORE_DOCBOOKS=1
  Documenation: update cgroup's document path
  Documentation/sphinx: do not warn about missing tools in 'make help'

Pull binfmt_misc update from James Bottomley:
 "This update is to allow architecture emulation containers to function
  such that the emulation binary can be housed outside the container
  itself.  The container and fs parts both have acks from relevant
  experts.

  To use the new feature you have to add an F option to your binfmt_misc
  configuration"

From the docs:
 "The usual behaviour of binfmt_misc is to spawn the binary lazily when
  the misc format file is invoked.  However, this doesn't work very well
  in the face of mount namespaces and changeroots, so the F mode opens
  the binary as soon as the emulation is installed and uses the opened
  image to spawn the emulator, meaning it is always available once
  installed, regardless of how the environment changes"

* tag 'binfmt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/binfmt_misc:
  binfmt_misc: add F option description to documentation
  binfmt_misc: add persistent opened binary handler for containers
  fs: add filp_clone_open API

In most cases, EPERM is returned on immutable inode, and there're only a
few places returning EACCES. I noticed this when running LTP on
overlayfs, setxattr03 failed due to unexpected EACCES on immutable
inode.

So converting all EACCES to EPERM on immutable inode.
Acked-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Eryu Guan <guaneryu@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more vfs updates from Al Viro:
 "Assorted cleanups and fixes.

  In the "trivial API change" department - ->d_compare() losing 'parent'
  argument"

* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  cachefiles: Fix race between inactivating and culling a cache object
  9p: use clone_fid()
  9p: fix braino introduced in "9p: new helper - v9fs_parent_fid()"
  vfs: make dentry_needs_remove_privs() internal
  vfs: remove file_needs_remove_privs()
  vfs: fix deadlock in file_remove_privs() on overlayfs
  get rid of 'parent' argument of ->d_compare()
  cifs, msdos, vfat, hfs+: don't bother with parent in ->d_compare()
  affs ->d_compare(): don't bother with ->d_inode
  fold _d_rehash() and __d_rehash() together
  fold dentry_rcuwalk_invalidate() into its only remaining caller

Merge tag 'xfs-rmap-for-linus-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs

Pull more xfs updates from Dave Chinner:
 "This is the second part of the XFS updates for this merge cycle, and
  contains the new reverse block mapping feature for XFS.

  Reverse mapping allows us to track the owner of a specific block on
  disk precisely.  It is implemented as a set of btrees (one per
  allocation group) that track the owners of allocated extents.
  Effectively it is a "used space tree" that is updated when we allocate
  or free extents.  i.e. it is coherent with the free space btrees we
  already maintain and never overlaps with them.

  This reverse mapping infrastructure is the building block of several
  upcoming features - reflink, copy-on-write data, dedupe, online
  metadata and data scrubbing, highly accurate bad sector/data loss
  reporting to users, and significantly improved reconstruction of
  damaged and corrupted filesystems.  There's a lot of new stuff coming
  along in the next couple of cycles,a nd it all builds in the rmap
  infrastructure.

  As such, it's a huge chunk of new code with new on-disk format
  features and internal infrastructure.  It warns at mount time as an
  experimental feature and that it may eat data (as we do with all new
  on-disk features until they stabilise).  We have not released
  userspace suport for it yet - userspace support currently requires
  download from Darrick's xfsprogs repo and build from source, so the
  access to this feature is really developer/tester only at this point.
  Initial userspace support will be released at the same time kernel
  with this code in it is released.

  The new rmap enabled code regresses 3 xfstests - all are ENOSPC
  related corner cases, one of which Darrick posted a fix for a few
  hours ago.  The other two are fixed by infrastructure that is part of
  the upcoming reflink patchset.  This new ENOSPC infrastructure
  requires a on-disk format tweak required to keep mount times in
  check - we need to keep an on-disk count of allocated rmapbt blocks so
  we don't have to scan the entire btrees at mount time to count them.

  This is currently being tested and will be part of the fixes sent in
  the next week or two so users will not be exposed to this change"

* tag 'xfs-rmap-for-linus-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs: (52 commits)
  xfs: move (and rename) the deferred bmap-free tracepoints
  xfs: collapse single use static functions
  xfs: remove unnecessary parentheses from log redo item recovery functions
  xfs: remove the extents array from the rmap update done log item
  xfs: in btree_lshift, only allocate temporary cursor when needed
  xfs: remove unnecesary lshift/rshift key initialization
  xfs: remove the get*keys and update_keys btree ops pointers
  xfs: enable the rmap btree functionality
  xfs: don't update rmapbt when fixing agfl
  xfs: disable XFS_IOC_SWAPEXT when rmap btree is enabled
  xfs: add rmap btree block detection to log recovery
  xfs: add rmap btree geometry feature flag
  xfs: propagate bmap updates to rmapbt
  xfs: enable the xfs_defer mechanism to process rmaps to update
  xfs: log rmap intent items
  xfs: create rmap update intent log items
  xfs: add rmap btree insert and delete helpers
  xfs: convert unwritten status of reverse mappings
  xfs: remove an extent from the rmap btree
  xfs: add an extent to the rmap btree
  ...

Pull qstr constification updates from Al Viro:
 "Fairly self-contained bunch - surprising lot of places passes struct
  qstr * as an argument when const struct qstr * would suffice; it
  complicates analysis for no good reason.

  I'd prefer to feed that separately from the assorted fixes (those are
  in #for-linus and with somewhat trickier topology)"

* 'work.const-qstr' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  qstr: constify instances in adfs
  qstr: constify instances in lustre
  qstr: constify instances in f2fs
  qstr: constify instances in ext2
  qstr: constify instances in vfat
  qstr: constify instances in procfs
  qstr: constify instances in fuse
  qstr constify instances in fs/dcache.c
  qstr: constify instances in nfs
  qstr: constify instances in ocfs2
  qstr: constify instances in autofs4
  qstr: constify instances in hfs
  qstr: constify instances in hfsplus
  qstr: constify instances in logfs
  qstr: constify dentry_init_security