Reorder backlight properties.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

White-space clean-up.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Drop unused pinmux label.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Add missing regulators:
- reg_module_3v3_audio being VDDA supply of SGTL5000
- VDDD supply of SGTL5000 actually being reg_1v8_vio
- TMP451 temperature sensor vcc supply being reg_module_3v3
- usb3-0 vbus supply being reg_usbh_vbus
- usb3-1 vbus supply being reg_usbo1_vbus
- carrier board HDMI supply being reg_5v0
- carrier board sata target 5v supply being reg_5v0
- carrier board sata target 12v supply being reg_12v0
- carrier board reg_3v3 actually being backlight power supply
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Just cosmetic regulator clean-up.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Reorder padctl properties.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Reorder Host1x/HDMI properties.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Add empty local-mac-address property to be filled in by boot loader
(e.g. U-Boot).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

The power I2C bus aka PWR_I2C which connects to the audio codec, PMIC,
temperature sensor and touch screen controller is really on-module only.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Both GEN2_I2C as well as CAM_I2C (I2C3) are unused in our design.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Add the MCP2515 SPI CAN controller's vdd-supply being the regular
carrier board's reg_3v3 and xceiver-supply being reg_5v0.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Get rid of the unused MCP2515 SPI CAN controller can0 label.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Fix the MCP2515 SPI CAN controller interrupt polarity which according
to its datasheet defaults to low-active aka falling edge.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Rename a few nodes using more common names:
- rename tps65911@2d to pmic@2d
- rename stmpe811@41 to touchscreen@41
- rename tps62362@60 to regulator@60
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Rename hdmiddc to hdmi_ddc to be more in-line with other device trees.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Drop obsolete spidev device tree node as nowadays one should do this
by binding the spidev driver to specific instances/chip selects at
runtime.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Drop model and compatible nodes from the module level device tree as
they get overridden by the carrier board device tree anyway.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Update compatibility comment.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Annotate EHCI instance 1 (USB2_DP/N) connecting to ASIX AX88772B USB to
Ethernet chip being on-module.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Annotate SD card detect.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Enable HDA over HDMI.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Add GPIO hog to unreset ASIX AX88772B USB Ethernet chip.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Remove unused nvidia,is-wired property.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Move input include to carrier board.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Line break long compatible property line.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Get rid of the fake clocks simple bus and use node names as per the
actual schematics.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Add mmc-ddr-1_8v property enabling eMMC DDR52 mode.

root@colibri-t30:~# cat /sys/kernel/debug/mmc1/ios
clock:          52000000 Hz
actual clock:   52000000 Hz
vdd:            21 (3.3 ~ 3.4 V)
bus mode:       2 (push-pull)
chip select:    0 (don't care)
power mode:     2 (on)
bus width:      3 (8 bits)
timing spec:    8 (mmc DDR52)
signal voltage: 1 (1.80 V)
driver type:    0 (driver type B)
root@colibri-t30:~# hdparm -t /dev/mmcblk1

/dev/mmcblk1:
 Timing buffered disk reads: 222 MB in  3.00 seconds =  73.92 MB/sec
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Add proper eMMC vmmc and vqmmc supplies e.g. fixing signalling voltage.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Add i2c-thermtrip which would set the DEV_OFF bit in the DCDC control
register of the TPS65911 PMIC.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Further LM95245 temperature sensor annotation.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Use proper irq-gpio for stmpe811 touch controller.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Explicitly mux all T30 SoC balls now:
- Colibri Address/Data Bus (GMI)
- Colibri DDC
- Colibri EXT_IO*
- Colibri GPIO
- Colibri HOTPLUG_DETECT (HDMI)
- Colibri I2C
- Colibri LCD (L_* resp. LDD<*>)
- Colibri MMC_CD
- Colibri nRESET_OUT
- Colibri Parallel Camera (Optional)
- Colibri PWM<B>, <C>, <D>
- Colibri VGA
- Colibri USBC_DET
- Colibri USBH_PEN
- Colibri USBH_OC
- on-module AX88772B LAN control signals
- Colibri nBATT_FAULT(SENSE) and nVDD_FAULT(SENSE
- not connected and therefore disabled signals
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Clean-up pinmuxing:
- white-space clean-up
- explicitly disable LCD_M1 in favour of LCD_DE on L_BIAS
- explicitly disable multiplexed SSPFRM and SSPTXD
- get rid of nvidia,lock property
- add missing eMMC sdmmc4_cmd_pt7 and explicitly enable input
- explicitly disable lcd_dc1_pd2 (e.g. LM95245 I2C address pin)
- annotate TOUCH_PEN_INT# being on-module
- As underscores in node names are not recommended replace them all
  where possible with dashes.
- Replace underscores in UART annotations (e.g. UART_A) with dashes
  (e.g. UART-A) to be more in-line with our Colibri standard.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Drop pwmleds in favour of using regular PWMs.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Reorder backlight properties.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Move dr_mode property from USB PHY node to controller.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

White-space clean-up.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Annotate UARTs and move the serial UART "nvidia,tegra30-hsuart"
compatible definitions from the carrier board to the module level device
trees. One could still override this in a custom carrier board device
tree if required.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Add missing regulators:
- reg_module_3v3_audio being VDDA supply of SGTL5000
- VDDD supply of SGTL5000 actually being reg_1v8_vio
- reg_lan_v_bus being USB Ethernet chip vbus supply
- carrier board HDMI supply being reg_5v0
- carrier board reg_3v3 actually being backlight and panel power supply
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Just cosmetic regulator clean-up.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>