Having a shorthand "dev" instead of &client->dev everywhere
makes the code easier to read (more compact).

Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Enabled i2c master controller support for LSM6DSM sensor. Enable
ext_sensor0 for lsm6dsm. This series has been tested using LIS2MDL as
slave device connected to the i2c controller of the LSM6DSM
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Rename st_lsm6dsx_shub_read_reg routine in st_lsm6dsx_shub_read_output
since it is used to read from sensorhub channel0 output register
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Check if the sensor hub output register is located in the primary or in the
secondary memory page. This is a preliminary patch to support i2c master
controller on lsm6dsm devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Check if the pull up register is located in the primary or in the
secondary memory page. This is a preliminary patch to support i2c master
controller on lsm6dsm devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Check if the master enable register is located in the primary or in the
secondary memory page. This is a preliminary patch to support i2c master
controller on lsm6dsm devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Export max number of slave devices supported by the i2c master
controller in st_lsm6dsx_shub_settings data structure.
This is a preliminary patch to support i2c master controller
on lsm6dsm sensors
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Fixes coccicheck warning:

./drivers/iio/light/lm3533-als.c:745:2-3: Unneeded semicolon
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Since the orginal scope of the driver was to only support
the pH product from Atlas it has evolved to other sensors.

Rename the file, driver name, and regmap to atlas-sensor which
reflects this, although keep CONFIG_ATLAS_PH_SENSOR to not cause
regressions with current configurations.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Kernel documentation script complains that some of the function parameters
are not described:

.../common/st_sensors/st_sensors_trigger.c:29: warning: Function parameter or member 'indio_dev' not described in 'st_sensors_new_samples_available'
.../common/st_sensors/st_sensors_trigger.c:29: warning: Function parameter or member 'sdata' not described in 'st_sensors_new_samples_available'

Describe function parameters where it's appropriate.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Since we put static variable to a header file it's copied to each module
that includes the header. But not all of them are actually used it.

Mark default_press_pdata with __maybe_unused to calm a compiler down:

In file included from drivers/iio/pressure/st_pressure_spi.c:18:
drivers/iio/pressure/st_pressure.h:40:46: warning: ‘default_press_pdata’ defined but not used [-Wunused-const-variable=]
   40 | static const struct st_sensors_platform_data default_press_pdata = {
      |                                              ^~~~~~~~~~~~~~~~~~~
...
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Since we put static variable to a header file it's copied to each module
that includes the header. But not all of them are actually used it.

Mark default_accel_pdata with __maybe_unused to calm a compiler down:

In file included from drivers/iio/accel/st_accel_i2c.c:19:
drivers/iio/accel/st_accel.h:67:46: warning: ‘default_accel_pdata’ defined but not used [-Wunused-const-variable=]
   67 | static const struct st_sensors_platform_data default_accel_pdata = {
      |                                              ^~~~~~~~~~~~~~~~~~~
...
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Since we put static variable to a header file it's copied to each module
that includes the header. But not all of them are actually used it.

Mark gyro_pdata with __maybe_unused to calm a compiler down:

In file included from drivers/iio/gyro/st_gyro_i2c.c:18:
drivers/iio/gyro/st_gyro.h:31:46: warning: ‘gyro_pdata’ defined but not used [-Wunused-const-variable=]
   31 | static const struct st_sensors_platform_data gyro_pdata = {
      |                                              ^~~~~~~~~~
...
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

ACPI_PTR() takes care of the argument in case of !CONFIG_ACPI.
Remove unnecessary #else branch.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

ACPI_PTR() takes care of the argument in case of !CONFIG_ACPI.
Remove unnecessary #else branch.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

There is no evidence that the driver supports or needs ACPI APIs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Device property API allows to gather device resources from different sources,
such as ACPI. Convert the drivers to unleash the power of device property API.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

There is no need to have OF guard against ID table.
Drop it for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Since we put static variable to a header file it's copied to each module
that includes the header. But not all of them are actually used it.

Mark predefined constants with __maybe_unused to calm a compiler down:

In file included from drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_i2c.c:17:
.../st_lsm6dsx/st_lsm6dsx.h:399:28: warning: ‘st_lsm6dsx_available_scan_masks’ defined but not used [-Wunused-const-variable=]
  399 | static const unsigned long st_lsm6dsx_available_scan_masks[] = {0x7, 0x0};
      |                            ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
.../st_lsm6dsx/st_lsm6dsx.h:392:36: warning: ‘st_lsm6dsx_event’ defined but not used [-Wunused-const-variable=]
  392 | static const struct iio_event_spec st_lsm6dsx_event = {
      |                                    ^~~~~~~~~~~~~~~~
...
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The ad7928 is software compatible with the ad7923.
The ad7908 and ad7918 are the 8 and 10-bit versions of the ad7928.
Signed-off-by: Daniel Junho <djunho@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Accomplish device tree compatibility to driver AD7923
by adding of_device_id table and making a subsequent call to
MODULE_DEVICE_TABLE.
Signed-off-by: Daniel Junho <djunho@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Fix checkpatch warning:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
+static int ad7923_scan_direct(struct ad7923_state *st, unsigned ch)
Signed-off-by: Daniel Junho <djunho@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Removes the unused define AD7923_CHANNEL_x from the code.
Signed-off-by: Daniel Junho <djunho@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add support for the VDD and VDDIO regulators using the regulator
framework.
Signed-off-by: Dan Robertson <dan@dlrobertson.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add a IIO driver for the Bosch BMA400 3-axes ultra-low power accelerometer.
The driver supports reading from the acceleration and temperature
registers. The driver also supports reading and configuring the output data
rate, oversampling ratio, and scale.
Signed-off-by: Dan Robertson <dan@dlrobertson.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add devicetree binding for the Bosch BMA400 3-axes ultra-low power
accelerometer sensor.
Signed-off-by: Dan Robertson <dan@dlrobertson.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This patch add device tree binding documentation for ADIS16240.
Signed-off-by: Rodrigo Carvalho <rodrigorsdc@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

According to the datasheet, this driver supports only SPI mode 3,
so we should enforce it on probe function.
Signed-off-by: Rodrigo Carvalho <rodrigorsdc@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This chip is similar to the LTC2497 ADC, it just uses SPI instead of I2C
and so has a slightly different protocol. Only the actual hardware
access is different. The spi protocol is different enough to not be able
to map the differences via a regmap.

Also generalize the entry in MAINTAINER to cover the newly introduced
file.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This allows to share most of this driver for the ltc2496 driver added in
the next commit that is an SPI variant of the ltc2497. Initially I named
the generic part ltc249x, but wild card names are frowned upon, so the
generic part is called ltc2497-core even though it's not obvious that
this is then to be reused for the ltc2496 driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The ADC only requires the standard stuff for spi devices and a reference
voltage.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Make use of device property API in this driver so that both OF based
system and ACPI based system can use this driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Platform data is a legacy interface to supply device properties
to the driver. In this case we even don't have in-kernel users
for it. Just remove it for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Fix a typo:
   s/get get/to get/
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Move some register definitions to hts221_avg_list, hts221_avg_list and
hts221_channels since they are used only there and simplify driver code
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Enable overrun interrupt on STM32 ADC. In case data register hasn't been
read (by CPU or DMA), overrun condition is detected when there's new
conversion data available. Stop grabbing data and log an error message.
Use a threaded irq to avoid printing the error message from hard irq
context.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

These three GPIO lines used by the Samsung sensor hub is pretty
straight-forward to convert to use GPIO descriptors.

Cc: Karol Wrona <k.wrona@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Ad7091R5 was added in a non alphabetical order after AD7124 in Makefile and
KConfig. This patch fixes that and place Ad7091R5 before AD7124.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The driver includes <linux/gpio.h> yet fails to use symbols
from any the header so drop the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The AD7266 have no in-tree users making use of the platform
data mechanism to pass address GPIO lines when not using
a fixed address, so we can easily convert this to use
GPIO descriptors instead of the platform data integers
currently passed.

Lowercase the labels "ad0".."ad2" as this will make a better
fit for platform descriptions like device tree that prefer
lowercase names such as "ad0-gpios" rather than "AD0-gpios".

Board files and other static users of this device can pass
the same GPIO descriptors using machine descriptor
tables if need be.

Cc: Alison Schofield <amsfield22@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>