- 15 Mar, 2011 2 commits
-
-
Joonyoung Shim authored
Atmel touchscreen chips have different firmware version with each chip, so we cannot distinguish attribute of chip by firmware version. Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Mark Brown authored
Explicitly set all the enable bits when opening the device just in case something left the device in an unexpected state. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
- 14 Mar, 2011 1 commit
-
-
Bo Shen authored
The AT42QT1070 QTouch sensor supports up to 7 keys. The driver has been tested on Atmel AT91SAM9M10-G45-EK board, and it should work fine on other platforms. Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
- 13 Mar, 2011 6 commits
-
-
Mark Brown authored
tslib expects pressure measurements so enable them by default for better compatibility. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Andy Botting authored
This patch add multitouch support for the MacBookPro8,1 and MacBookPro8,2 models. Cc: stable@kernel.org Signed-off-by: Andy Botting <andy@andybotting.com> Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Acked-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Ping Cheng authored
Reviewed-by: Henrik Rydberg <rydberg@euromail.se> Reviewed-by: Chris Bagwell <chris@cnpbagwell.com> Signed-off-by: Ping Cheng <pingc@wacom.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Ping Cheng authored
There are two types of 1FGT devices supported in wacom_wac.c. Changing them to follow the existing touchscreen format, i.e., only report BTN_TOUCH as a valid tool type. Touch data will be ignored if pen is in proximity. This requires a touch up event sent if touch was down when pen comes in. The touch up event should be sent before any pen events are emitted. Otherwise, two pointers would race for the cursor. However, we can not send a touch up inside wacom_tpc_pen since pen and touch are on different logical port. That is why we have to check if touch is up before sending pen events. Reviewed-by: Henrik Rydberg <rydberg@euromail.se> Reviewed-by: Chris Bagwell <chris@cnpbagwell.com> Signed-off-by: Ping Cheng <pingc@wacom.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Ping Cheng authored
So it would be easier for patch reviewers to follow the data path. Reviewed-by: Henrik Rydberg <rydberg@euromail.se> Reviewed-by: Chris Bagwell <chris@cnpbagwell.com> Signed-off-by: Ping Cheng <pingc@wacom.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Ping Cheng authored
2FGT Tablet PC touch events were processed in _TAP_ format. Remove them so we can change to _MT_ format. Signed-off-by: Ping Cheng <pingc@wacom.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
- 25 Feb, 2011 1 commit
-
-
Iiro Valkonen authored
The mxt_check_matrix_size() is currently setting the CTE mode to match xline/yline information that is in the platform data, but it does not take into account for example the fact that we could have a key array in use too (key array would use some x/y lines as well). It would be better to simply rely on the configuration data, and make sure that the CTE mode set in there matches the touch object (touchscreen, key array, proximity) configuration (which are set in the config data too). Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
- 24 Feb, 2011 3 commits
-
-
HeungJun Kim authored
The MCS50XX series has a HW bug that requires explicit chip power down. If chip is not powered down before shutting the system down the control pins (powerup, interrupt) are pulled up and residue current continues flowing into the chips making them continue consuming power. Signed-off-by: Heungjun Kim <riverful.kim@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Heungjun Kim authored
This adds support for system-level suspend/resume to the driver. Signed-off-by: Heungjun Kim <riverful.kim@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Abraham Arce authored
Enable Runtime PM functionality in OMAP4 driver based on the following assumptions: - keyboard controller in wakeup domain so it is always on and power impact is minimal; - in OMAP4 the device control is at module/device level and ick/fclk level control is difficult so cutting of clocks will prevent interrupts. Signed-off-by: Abraham Arce <x0066660@ti.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
- 21 Feb, 2011 17 commits
-
-
Dan Carpenter authored
The test here is reversed. It should be if (IS_ERR()) instead of if (!IS_ERR()). Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Iiro Valkonen authored
Different board have different requirements/setups so let's be more flexible. Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Iiro Valkonen authored
As there is no common configuration settings that would work in every situation, remove the fixed config data from driver code and add config data to platform data. Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Chris Leech authored
"mXT224" is used in the Intel mid firmware in SFI tables to identify the presence of this I2C device. Signed-off-by: Chris Leech <christopher.leech@linux.intel.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Mark Brown authored
There is a general move to convert drivers to dev_pm_ops rather than bus specific PM ops in order to facilitate core development. Do this converison for synaptics-i2c. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Mark Brown authored
The adxl34x SPI driver has what appears to be a typo referring to the device as adx134x with the numeral 1 rather than letter l. This appears to be an error so convert. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Mark Brown authored
There is a general move to convert drivers to use dev_pm_ops rather than bus specific ones in order to facilitate core development. Do this conversion for adxl34x-spi. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Mark Brown authored
There is a general move to convert drivers to use dev_pm_ops rather than bus specific ones in order to facilitate core development. Do this conversion for adxl34x-i2c. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Mark Brown authored
There is a general move to convert drivers to use dev_pm_ops rather than bus specific ops to facilitate core work. Do this conversion for max7359. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Mark Brown authored
There is a general move away from bus specific PM operations to using dev_pm_ops in order to facilicate core improvements. Update lm8323 to the new model. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Mark Brown authored
There is a general move to convert drivers to use dev_pm_ops rather than bus specific PM operations in order to facilitate core work. Do this conversion for ad714x-spi. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Mark Brown authored
There is a general move to convert drivers to use dev_pm_ops rather than bus specific PM operations in order to facilitate core work. Do this conversion for ad714x-i2c. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Dmitry Torokhov authored
Instead of open-coding copying of data structures from userspace use memdup_user() and strndup_user(). Note that this introduces change in behavior because driver used to truncate 'phys' longer than 1024 bytes, but now it will refuse to set 'phys' that long. Arguably trying to set such 'phys' is suspect anyways. Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
David Herrmann authored
The check for non-empty device name was botched since we tried to account for extra space for the terminating zero at the same time. Convert to kstrndup() to avoid this problem. Signed-off-by: David Herrmann <dh.herrmann@gmail.com> Acked-by: Aristeu Rozanski <aris@ruivo.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Iiro Valkonen authored
Read the whole message, as reading just the first byte isn't always guaranteed to clear the message. Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Iiro Valkonen authored
Change prefixes from qt602240 to mxt to reflect that the driver supports whole line of mXT touchscreens. Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Dmitry Torokhov authored
Since the driver will be supporting whole range of Atmels mXT touchscreen controllers we better rename it to atmel_mxt_ts. Acked-by: Iiro Valkonen <iiro.valkonen@atmel.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
- 01 Feb, 2011 6 commits
-
-
Dmitry Torokhov authored
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Dmitry Torokhov authored
All users of old style get/setkeycode methids have been converted so it is time to retire them. Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com> Acked-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Dmitry Torokhov authored
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Dmitry Torokhov authored
-
Mark Brown authored
While being applied the driver was modified to add use of the ternary operator. Write the conditionals out longhand as I find it terribly unhelpful for legibility. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-
Linus Torvalds authored
-
- 31 Jan, 2011 4 commits
-
-
git://git.linux-nfs.org/projects/trondmy/nfs-2.6Linus Torvalds authored
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6: NFS: NFSv4 readdir loses entries NFS: Micro-optimize nfs4_decode_dirent() NFS: Fix an NFS client lockdep issue NFS construct consistent co_ownerid for v4.1 NFS: nfs_wcc_update_inode() should set nfsi->attr_gencount NFS improve pnfs_put_deviceid_cache debug print NFS fix cb_sequence error processing NFS do not find client in NFSv4 pg_authenticate NLM: Fix "kernel BUG at fs/lockd/host.c:417!" or ".../host.c:283!" NFS: Prevent memory allocation failure in nfsacl_encode() NFS: nfsacl_{encode,decode} should return signed integer NFS: Fix "kernel BUG at fs/nfs/nfs3xdr.c:1338!" NFS: Fix "kernel BUG at fs/aio.c:554!" NFS4: Avoid potential NULL pointer dereference in decode_and_add_ds(). NFS: fix handling of malloc failure during nfs_flush_multi()
-
Linus Torvalds authored
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm: ARM: smp_on_up: allow non-ARM SMP processors ARM: io: ensure inb/outb() et.al. are properly ordered on ARMv6+ ARM: initrd: disable initrd if passed address overlaps reserved region ARM: footbridge: fix debug macros ARM: mmci: round down the bytes transferred on error ARM: mmci: complete the transaction on error ARM: 6642/1: mmci: calculate remaining bytes at error correctly
-
Linus Torvalds authored
Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 * 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: arch/arm/mach-omap2/dma.c: Convert IS_ERR result to PTR_ERR arm: omap2: mux: fix compile warning omap1: Simplify use of omap_irq_flags omap2+: Fix unused variable warning for omap_irq_base
-
Randy Dunlap authored
Fix kernel-doc warning in kernel.h from commit 7ef88ad5 ("BUILD_BUG_ON: make it handle more cases"): Warning(include/linux/kernel.h:605): No description found for parameter 'condition' Warning(include/linux/kernel.h:605): Excess function parameter 'cond' description in 'BUILD_BUG_ON' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-