- 07 Jul, 2011 40 commits
-
-
Wolfram Sang authored
Signed-off-by:
Wolfram Sang <w.sang@pengutronix.de> Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de>
-
Daiane Angolini authored
Signed-off-by:
Daiane Angolini <daiane.angolini@freescale.com> Signed-off-by:
-
Fabio Estevam authored
commit 9203d59 (ARM:mach-mx5/mx53_ard: Add I2C2 and I2C3 support) missed to include the define for ARD_I2CPORTEXP_B. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
Fabio Estevam authored
Signed-off-by:
-
Fabio Estevam authored
Signed-off-by:
-
Fabio Estevam authored
MX53 has five UART ports. Add support for the missing UART4 and UART5 ports. Signed-off-by:
-
Shawn Guo authored
It is not good to have cpu_name and to_version encoded into sdma firmware name as variables. For example, there are three TOs of imx51 soc, the sdma script never changes since TO1, which means all three TOs of imx51 uses TO1 version of sdma script. But we have to prepare three identical firmwares, sdma-imx51-to1.bin sdma-imx51-to2.bin and sdma-imx51-to3.bin, to have the kernel capable of running on all three TOs. The patch removes cpu_name and to_version from sdma platform data, and instead uses fw_name to pass the firmware name, so that we can pass the TO version where it's relevant and skip it where only one firmware exists. Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Acked-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Shawn Guo authored
The patch follows the implementation of gpio-mxc device registration to break the concentrated imx-dma device registration into soc specific setup function. Then we can avoid the churn of "#ifdef" and the cpu_is_mx checking on such a long list, which makes no sense, considering more soc supports need to be added and we need to support single image for multiple socs in the long run. Signed-off-by:
-
Andre Silva authored
Signed-off-by:
Andre Silva <andre.silva@freescale.com> Signed-off-by:
-
Andre Silva authored
Signed-off-by:
-
Fabio Estevam authored
Signed-off-by:
-
Fabio Estevam authored
On mx27_3ds board there is a l4f00242t03 LCD that is controlled via CSPI1. Add support for CSPI1 and LCD. Signed-off-by:
-
Dinh Nguyen authored
Adds initial low power suspend functionality to MX51. Supports "mem" and "standby" modes. Tested on mx51-babbage. Signed-off-by:
Dinh Nguyen <Dinh.Nguyen@freescale.com> Tested-by:
Arnaud Patard <arnaud.patard@rtp-net.org> Tested-by:
-
Fabio Estevam authored
On MX1, MX21 and MX27 each GPIO port has an address space of 256 bytes. Fix the iosize for these platforms. Tested on a mx27_3ds board that can boot fine after this change. Cc: Shawn Guo <shawn.guo@freescale.com> Signed-off-by:
-
Fabio Estevam authored
Signed-off-by:
-
Fabio Estevam authored
Signed-off-by:
-
Andre Silva authored
Signed-off-by:
-
Andre Silva authored
Signed-off-by:
-
Andre Silva authored
Signed-off-by:
-
Andre Silva authored
Signed-off-by:
-
Andre Silva authored
Signed-off-by:
-
Shawn Guo authored
The patch converts mxc tzic interrupt controller to use generic irq chip. Signed-off-by:
-
Shawn Guo authored
It adds LED2 on mx28evk board as heartbeat trigger for diagnostic purpose. Signed-off-by:
-
Fabio Estevam authored
Signed-off-by:
-
Fabio Estevam authored
Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Shawn Guo authored
The patch adds following configurations to enable build of mx23evk and mx28evk in defconfig. CONFIG_MACH_MX23EVK CONFIG_MACH_MX28EVK Signed-off-by:
-
Sascha Hauer authored
Conflicts: arch/arm/mach-imx/mach-mx31_3ds.c arch/arm/mach-imx/mach-scb9328.c Signed-off-by: -
Sascha Hauer authored
CONFIG_ARCH_* are deprecated, so remove one user. Signed-off-by: -
Fabio Estevam authored
On the i.MX SPI driver the chipselect pins can be of the following types: - internal: when the chipselect pin is used as a dedicated CS pin of the CSPI controller - GPIO: a generic GPIO can be used as a chipselect funtion On the mx27_3ds the SPI2 chip select is a GPIO, so don't annotate 'internal' in the chip select definition. Signed-off-by:
-
Fabio Estevam authored
Use the standard gpio_to_irq function instead of a dedicated IRQ_GPIOx macro. Signed-off-by:
-
Fabio Estevam authored
Place the UART gpio initialization inside the scb9328_init function as it is done on other i.MX boards. Signed-off-by:
-
H Hartley Sweeten authored
Signed-off-by:
H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Sascha Hauer <kernel@pengutronix.de> Signed-off-by:
-
Fabio Estevam authored
As no flag is passed into UART0 platform data, pass NULL argument when registering UART0. Signed-off-by:
-
Sascha Hauer authored
There are several occurences where MXC_INTERNAL_IRQ is assumed to be the start of the gpio interrupts. It was never meant this way. Replace these with gpio_to_irq. Signed-off-by:
-
Sascha Hauer authored
This becomes meaningless in subsequent patches. Signed-off-by: -
Sascha Hauer authored
This becomes meaningless in subsequent patches. Signed-off-by: -
Sascha Hauer authored
CONFIG_ARCH_* are deprecated, so remove one user. Signed-off-by: -
Sascha Hauer authored
since we now can include all soc specific headers at once we do not need the ifdeffery anymore. Signed-off-by: -
Sascha Hauer authored
All soc specific header have proper namespace now and thus can be included at once. Signed-off-by: -
Sascha Hauer authored
We have a clocksource which renders CLOCK_TICK_RATE useless. Define it to a bogus value to get rid of some ifdeffery. Signed-off-by:
-
