We are doing ->buf_prepare(buf) before adding buf to q->stream list. This
means that videobuf_qbuf() should not try to re-add a STATE_PREPARED buffer.

(cherry picked from commit 419dd837)
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Autodetect LG TAPC G701D as tuner type 37, fixing
mis-detected tuners in some Hauppauge tv tuner cards.

Thanks to Adonis Papas, for pointing this out.

(cherry picked from commit 1323fbda)
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Or status flags together in DECODER_GET_STATUS instead of and-zapping them.

(cherry picked from commit 55d5440d)
Signed-off-by: Martin Samuelsson <sam@home.se>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Host endianess does not affect the order that pixel rgb data comes
in from the quickcam (the values are bytes, not words or longs).  The
driver is erroniously swapping the order of rgb values for big endian
machines.  This patch is needed get the Quickcam communicator working
on big endian machines (tested on powerpc)

(cherry picked from commit c6d704c8)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Due to type confusion, when an nfsacl verison 2 'ACCESS' request
finishes and tries to clean up, it calls fh_put on entiredly the
wrong thing and this can cause an oops.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Remove the __resched_legal() check: it is conceptually broken.  The biggest
problem it had is that it can mask buggy cond_resched() calls.  A
cond_resched() call is only legal if we are not in an atomic context, with
two narrow exceptions:

 - if the system is booting
 - a reacquire_kernel_lock() down() done while PREEMPT_ACTIVE is set

But __resched_legal() hid this and just silently returned whenever
these primitives were called from invalid contexts. (Same goes for
cond_resched_locked() and cond_resched_softirq()).

Furthermore, the __legal_resched(0) call was buggy in that it caused
unnecessarily long softirq latencies via cond_resched_softirq().  (which is
only called from softirq-off sections, hence the code did nothing.)

The fix is to resurrect the efficiency of the might_sleep checks and to
only allow the narrow exceptions.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[chrisw: backport to 2.6.19.2]
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

move_task_off_dead_cpu() requires interrupts to be disabled, while
migrate_dead() calls it with enabled interrupts.  Added appropriate
comments to functions and added BUG_ON(!irqs_disabled()) into
double_rq_lock() and double_lock_balance() which are the origin sources of
such bugs.
Signed-off-by: Kirill Korotaev <dev@openvz.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

This patch fixes a regression in 2.6.19 in which the use of multiple
krb5 mounts against the same NFS server may result in an Oops on
unmount. The Oops is due to the fact that multiple NFS krb5 clients may
end up inadvertently sharing the same rpc_pipefs upcall pipe. The first
client to 'umount' will unlink that shared pipe, causing an Oops.

The solution is to give each client their own upcall pipe. This fix has
been in mainline since 2.6.20-rc1.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
[chrisw: backport to 2.6.19.2]
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

When the packet counter of a connection is zero a division by zero
occurs in div64_64(). Fix that by using zero as average value, which
is correct as long as the packet counter didn't overflow, at which
point we have lost anyway.

Additionally we're probably going to go back to 64 bit counters
in 2.6.21.

Based on patch from Jonas Berlin <xkr47@outerspace.dyndns.org>,
with suggestions from KOVACS Krisztian <hidden@balabit.hu>.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

I encountered a kernel panic with my test program, which is a very
simple IPv6 client-server program.

The server side sets IPV6_RECVPKTINFO on a listening socket, and the
client side just sends a message to the server.  Then the kernel panic
occurs on the server.  (If you need the test program, please let me
know. I can provide it.)

This problem happens because a skb is forcibly freed in
tcp_rcv_state_process().

When a socket in listening state(TCP_LISTEN) receives a syn packet,
then tcp_v6_conn_request() will be called from
tcp_rcv_state_process().  If the tcp_v6_conn_request() successfully
returns, the skb would be discarded by __kfree_skb().

However, in case of a listening socket which was already set
IPV6_RECVPKTINFO, an address of the skb will be stored in
treq->pktopts and a ref count of the skb will be incremented in
tcp_v6_conn_request().  But, even if the skb is still in use, the skb
will be freed.  Then someone still using the freed skb will cause the
kernel panic.

I suggest to use kfree_skb() instead of __kfree_skb().
Signed-off-by: Masayuki Nakagawa <nakagawa.msy@ncos.nec.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

The sorting of SACK blocks actually munges them rather than sort,
causing the TCP stack to ignore some SACK information and breaking the
assumption of ordered SACK blocks after sorting.

The sort takes the data from a second buffer which isn't moved causing
subsequent data moves to occur from the wrong location. The fix is to
use a temporary buffer as a normal sort does.
Signed-off-By: Baruch Even <baruch@ev-en.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

The patch "Replace CHECKSUM_HW by CHECKSUM_PARTIAL/CHECKSUM_COMPLETE"
changed to unconditional copying of ip_summed field from collapsed
skb. This patch reverts this change.

The majority of substantial work including heavy testing
and diagnosing by: Michael Tokarev <mjt@tls.msk.ru>
Possible reasons pointed by: Herbert Xu and Patrick McHardy.
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

If the device is down, invoking the device hard header callbacks
is not legal, so check it early.

Based upon a shaper OOPS report from Frederik Deweerdt.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

This fixes a bug introduced by:

commit fda9ef5d
Author: Dmitry Mishin <dim@openvz.org>
Date:   Thu Aug 31 15:28:39 2006 -0700

    [NET]: Fix sk->sk_filter field access

sk_run_filter() returns either 0 or an unsigned 32-bit
length which says how much of the packet to retain.
If that 32-bit unsigned integer is larger than the packet,
this is fine we just leave the packet unchanged.

The above commit caused all filter return values which
were negative when interpreted as a signed integer to
indicate a packet drop, which is wrong.

Based upon a report and initial patch by Raivis Bucis.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

When main table is just a single leaf this gets printed as belonging to the
local table in /proc/net/fib_trie. A fix is below.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

In a kernel with trie routing enabled I had a simple routing setup
with only a single route to the outside world and no default
route. "ip route table list main" showed my the route just fine but
/proc/net/route was an empty file.  What was going on?

Thinking it was a bug in something I did and I looked deeper.  Eventually
I setup a second route and everything looked correct, huh?  Finally I
realized that the it was just the iterator pair in fib_trie_get_first,
fib_trie_get_next just could not handle a routing table with a single entry.

So to save myself and others further confusion, here is a simple fix for
the fib proc iterator so it works even when there is only a single route
in a routing table.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

In some cases such as:
	iph->check = 0;
	iph->check = ip_fast_csum((unsigned char *)iph, iph->ihl);
GCC may optimize out the previous store.

Observed as a failure of NFS over udp (bad checksums on ip fragments)
when compiled with GCC 3.4.2.
Signed-off-by: Bob Breuer <breuerr@mc.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

While enhancing the neighbour code to handle multiple network
namespaces I noticed that decnet is assuming neigh_parms_alloc
will allways succeed, which is clearly wrong.  So handle the
failure.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Steven Whitehouse <steve@chygwyn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

jmicron module detects all JMB36x as JMB361 and PATA0 has wrong pin status
of XICBLID.

Cc: Jeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

cebbert@redhat.com: I folded in the warning fix (a51545ab) because
otherwise it makes the tester think the patch caused the warning
that was already there.

Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

While working with the latest bonding code I noticed a nasty problem that
will prevent arp monitoring from always functioning correctly on x86_64
systems.  Comparing ints to longs and expecting reliable results on x86_64
is a bad idea.  With this patch, arp monitoring works correctly again.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@osdl.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

Use the same signal frame alignment calculations as the underlying
architecture.  x86_64 appeared to do this, but the "- 8" was really
subtracting 8 * sizeof(struct rt_sigframe) rather than 8 bytes.

UML/i386 might have been OK, but I changed the calculation to match
i386 just to be sure.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: <stable@kernel.org>
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Antoine Martin <antoine@nagafix.co.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

When expanding the stack, we don't currently check if the VMA will cross
into an area of the address space that is reserved for hugetlb pages.
Subsequent faults on the expanded portion of such a VMA will confuse the
low-level MMU code, resulting in an OOPS.  Check for this.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

We are inside spin_lock_irqsave().  quoth akpm's debug facility:

 [  231.948000] SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
 [  232.232000] ata1.00: configured for UDMA/33
 [  232.404000] WARNING (1) at arch/i386/mm/highmem.c:47 kmap_atomic()
 [  232.404000]  [<c01162e6>] kmap_atomic+0xa9/0x1ab
 [  232.404000]  [<c0242c81>] ata_scsi_rbuf_get+0x1c/0x30
 [  232.404000]  [<c0242caf>] ata_scsi_rbuf_fill+0x1a/0x87
 [  232.404000]  [<c0243ab2>] ata_scsiop_mode_sense+0x0/0x309
 [  232.404000]  [<c01729d5>] end_bio_bh_io_sync+0x0/0x37
 [  232.404000]  [<c02311c6>] scsi_done+0x0/0x16
 [  232.404000]  [<c02311c6>] scsi_done+0x0/0x16
 [  232.404000]  [<c0242dcc>] ata_scsi_simulate+0xb0/0x13f
[...]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

If a GFP_KERNEL allocation is attempted in md while the mddev_lock is
held, it is possible for a deadlock to eventuate.
This happens if the array was marked 'clean', and the memalloc triggers
a write-out to the md device.
For the writeout to succeed, the array must be marked 'dirty', and that
requires getting the mddev_lock.

So, before attempting a GFP_KERNEL alloction while holding the lock,
make sure the array is marked 'dirty' (unless it is currently read-only).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

While developing more functionality in mdadm I found some bugs in md...

- When we remove a device from an inactive array (write 'remove' to
  the 'state' sysfs file - see 'state_store') would should not
  update the superblock information - as we may not have
  read and processed it all properly yet.

- initialise all raid_disk entries to '-1' else the 'slot sysfs file
  will claim '0' for all devices in an array before the array is
  started.

- all '\n' not to be present at the end of words written to
  sysfs files
- when we use SET_ARRAY_INFO to set the md metadata version,
  set the flag to say that there is persistant metadata.
- allow GET_BITMAP_FILE to be called on an array that hasn't
  been started yet.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

When 'repair' finds a block that is different one the various
parts of the mirror. it is meant to write a chosen good version
to the others.  However it currently writes out the original data
to each. The memcpy to make all the data the same is missing.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

Fix few bugs that meant that:
  - superblocks weren't alway written at exactly the right time (this
    could show up if the array was not written to - writting to the array
    causes lots of superblock updates and so hides these errors).

  - restarting device recovery after a clean shutdown (version-1 metadata
    only) didn't work as intended (or at all).

1/ Ensure superblock is updated when a new device is added.
2/ Remove an inappropriate test on MD_RECOVERY_SYNC in md_do_sync.
   The body of this if takes one of two branches depending on whether
   MD_RECOVERY_SYNC is set, so testing it in the clause of the if
   is wrong.
3/ Flag superblock for updating after a resync/recovery finishes.
4/ If we find the neeed to restart a recovery in the middle (version-1
   metadata only) make sure a full recovery (not just as guided by
   bitmaps) does get done.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

The nfsservctl systemcall isn't used but recent nfs-utils releases for
exporting filesystems, and consequently the code that is uses -
exp_export - has suffered some bitrot.

Particular:
  - some newly added fields in 'struct svc_export' are being initialised
    properly.
  - the return value is now always -ENOMEM ...

This patch fixes both these problems.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

nfsd defines a type 'encode_dent_fn' which is much like 'filldir_t'
except that the first pointer is 'struct readdir_cd *' rather than
'void *'.  It then casts encode_dent_fn points to 'filldir_t' as
needed.  This hides any other type mismatches between the two such as
the fact that the 'ino' arg recently changed from ino_t to u64.

So: get rid of 'encode_dent_fn', get rid of the cast of the function
type, change the first arg of various functions from 'struct readdir_cd *'
to 'void *', and live with the fact that we have a little less type
checking on the calling of these functions now.
Less internal (to nfsd) checking offset by more external checking, which
is more important.

Thanks to Gabriel Paubert <paubert@iram.es> for discovering this and
providing an initial patch.
Signed-off-by: Gabriel Paubert <paubert@iram.es>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

NFSd assumes that largest number of pages that will be needed
for a request+response is 2+N where N pages is the size of the largest
permitted read/write request.  The '2' are 1 for the non-data part of
the request, and 1 for the non-data part of the reply.

However, when a read request is not page-aligned, and we choose to use
->sendfile to send it directly from the page cache, we may need N+1
pages to hold the whole reply.  This can overflow and array and cause
an Oops.

This patch increases size of the array for holding pages by one and
makes sure that entry is NULL when it is not in use.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

Due to silly typos, if the nfs versions are explicitly set,
no NFSACL versions get enabled.

Also improve an error message that would have made this bug
a little easier to find.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

Fix from http://bugzilla.kernel.org/show_bug.cgi?id=7747Signed-off-by: Andrew Morton <akpm@osdl.org>
Cc: <sleepy@mike-neko.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

Mirror the logic in the sun4u handler, we have to update
both registers even when we branch out to window fault
fixup handling.

The way it works is that if we are in etrap processing a
fault already, g4/g5 holds the original fault information.
If we take a window spill fault while doing etrap, then
we put the window spill fault info into g4/g5 and this is
what the top-level fault handler ends up processing first.

Then we retry the originally faulting instruction, and
process the original fault at that time.

This is all necessary because of how constrained the trap
registers are in these code paths.  These cases trigger
very rarely, so even if there is some performance implication
it's doesn't happen very often.  In fact the rarity is why
it took so long to trigger and find this particular bug.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

rtc_sysfs_add_device is needed even after dev initialization, so drop __devinit.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

This reverts commit 99a10a60.

As per Hugh Dickins:

  "Nadia Derbey has reported that mmap of /dev/kmem no longer works with
   the kernel virtual address as offset, and Franck has confirmed that
   his patch came from a misunderstanding of what an offset means to
   /dev/kmem - whereas his patch description seems to say that he was
   correcting the offset on a few plaforms, there was no such problem to
   correct, and his patch was in fact changing its API on all platforms."
Suggested-by: Hugh Dickins <hugh@veritas.com>
Cc: Franck Bui-Huu <fbuihuu@gmail.com>
Cc: Nadia Derbey <Nadia.Derbey@bull.net>
Cc: Andi Kleen <ak@suse.de>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

A flag was recently added to the elevator code to avoid
performing an unplug when reuests are being re-queued.
The goal of this flag was to avoid a deep recursion that
can occur when re-queueing requests after a SCSI device/host
reset.  See http://lkml.org/lkml/2006/5/17/254

However, that fix added the flag near the bottom of a case
statement, where an earlier break (in an if statement) could
transport one out of the case, without setting the flag.
This patch sets the flag earlier in the case statement.

I re-discovered the deep recursion recently during testing;
I was told that it was a known problem, and the fix to it was
in the kernel I was testing. Indeed it was ... but it didn't
fix the bug. With the patch below, I no longer see the bug.

Signed-off by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

With the introduction of x_tables we accidentally broke compatibility
by defining IPT_TABLE_MAXNAMELEN to XT_FUNCTION_MAXNAMELEN instead of
XT_TABLE_MAXNAMELEN, which is two bytes larger.

On most architectures it doesn't really matter since we don't have
any tables with names that long in the kernel and the structure
layout didn't change because of alignment requirements of following
members. On CRIS however (and other architectures that don't align
data) this changed the structure layout and thus broke compatibility
with old iptables binaries.

Changing it back will break compatibility with binaries compiled
against recent kernels again, but since the breakage has only been
there for three releases this seems like the better choice.

Spotted by Jonas Berlin <xkr47@outerspace.dyndns.org>.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

The new PDA code uses a dummy _proxy_pda variable to describe
memory references to the PDA. It is never referenced
in inline assembly, but exists as input/output arguments.
gcc 4.2 in some cases can CSE references to this which causes
unresolved symbols.  Define it to zero to avoid this.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>