Fixes gcc '-Wunused-but-set-variable' warning:

	drivers/pwm/pwm-pca9685.c: In function ‘pca9685_pwm_gpio_free’:
	drivers/pwm/pwm-pca9685.c:162:21: warning: variable ‘pwm’ set but not used [-Wunused-but-set-variable]

It is never used, and so can be removed. In that case, hold and release
the lock 'pca->lock' can be removed since nothing will be done between
them.

Fixes: e926b12c ("pwm: Clear chip_data in pwm_put()")
Signed-off-by: yu kuai <yukuai3@huawei.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

GCC can't always determine that the duty, period and prescaler values
are initialized when returning from sun4i_pwm_calculate(), so help out a
little by initializing them to 0.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Don't use AOE (automatic output enable) by default. In case of break
events, PWM is automatically re-enabled on next PWM cycle otherwise.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

The variable pval is only used in a single block in the function
sun4i_pwm_calculate(). So declare it in a more local scope to simplify
the function for humans and compilers.

While at it also simplify assignment to pval.

While the diffstat for this patch is negative for this patch I still
thing the advantage of having a narrower scope is beneficial.

In my compiler / .config setup (gcc 8.2.1, arm/imx_v6_v7_defconfig +
COMPILE_TEST + PWM_SUN4I) this change doesn't result in any binary
changes.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

BCM7211 is supported using ARCH_BRCMSTB and uses this PWM controller
driver, make it possible to build it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

For defer probe error, no need to output error message which
will cause confusion.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Fix inconsistent IS_ERR and PTR_ERR in sun4i_pwm_probe().

The proper pointers to be passed as arguments are pwm->clk and pwm->bus_clk.

This bug was detected with the help of Coccinelle.

Fixes: b8d74644 ("pwm: sun4i: Prefer "mod" clock to unnamed")
Fixes: 5b090b43 ("pwm: sun4i: Add an optional probe for bus clock")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

pwm_calculate() calls clk_get_rate() while holding a spin_lock().

This create an issue as clk_get_rate() may sleep.

Move pwm_calculate() out of this spin_lock().

Fixes: c32c5c50 ("pwm: sun4i: Switch to atomic PWM")
Reported-by: Alexander Finger <alex.mobigo@gmail.com>
Sugested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Alexander Finger <alex.mobigo@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

The dependency on OMAP_DM_TIMER is only a runtime dependency. Also
OMAP_DM_TIMER cannot be enabled without ARCH_OMAP being enabled.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

This was found by coccicheck:

	drivers/pwm/pwm-omap-dmtimer.c:304:2-8: ERROR: missing put_device;
	call of_find_device_by_node on line 255, but without a corresponding
	object release within this function.
Reported-by: Markus Elfring <elfring@users.sourceforge.net>
Fixes: 6604c655 ("pwm: Add PWM driver for OMAP using dual-mode timers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Instead of doing error handling in the middle of ->probe(), move error
handling and freeing the reference to timer to the end.

This fixes a resource leak as dm_timer wasn't freed when allocating
*omap failed.

Implementation note: The put: label was never reached without a goto and
ret being unequal to 0, so the removed return statement is fine.

Fixes: 6604c655 ("pwm: Add PWM driver for OMAP using dual-mode timers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

In the old code (e.g.) mutex_destroy() was called before
pwmchip_remove(). Between these two calls it is possible that a PWM
callback is used which tries to grab the mutex.

Fixes: 6604c655 ("pwm: Add PWM driver for OMAP using dual-mode timers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

This allows to log all calls to the driver's lowlevel functions which
simplifies debugging in some cases.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

When .apply() is called with state->duty_cycle = 0 the duty_ns parameter
to rcar_pwm_set_counter() is 0 which results in ph being 0 and
rcar_pwm_set_counter() returning -EINVAL.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

pwm_get_state has no side effects and the resulting pwm_state is unused.
So drop the call to pwm_get_state() and the local variable from
rcar_pwm_apply().

The call was introduced in commit 7f68ce82 ("pwm: rcar: Add support
"atomic" API") and already then was useless.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Remove double whitespace after "config" keyword.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

This function reads back the configured parameters from the hardware. As
.apply() rounds down (mostly) I'm rounding up in .get_state() to achieve
that applying a state just read from hardware is a no-op.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

This makes it a bit easier when instrumenting register access to only
have to add code in one place.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

This documents the my findings while reading through the driver and the
reference manual.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

The calculated values are the same with the modified algorithm. The only
difference is that the calculation is a bit more efficient.
Acked-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

The maximal prescale value is 10 for all supported variants. So drop the
member in the variant description and introduce a global constant
instead.

This reduces the size of the variant descriptions and the .apply()
callback can be compiled a bit more effectively.
Acked-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Most Microchip (formerly Atmel) chips have publicly available manuals.
A comprehensive list is already contained in the documentation folder.
Reference this list in the header of the driver to allow reviewers to
find the relevant manuals.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Since the divisor is not a compile-time constant (unless gcc somehow
decided to unroll the loop PERIOD_CDIV_MAX times), this does a
somewhat expensive 32/32 division. Replace that with a right shift.

We still have a 64/32 division just below, but at least in that
case the divisor is compile-time constant.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

We need to increase the pwm-cells for the optional flags parameter, in
order to implement support for polarity setting via DT.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

If I'm reading of_pwm_xlate_with_flags() right, existing device trees
that set #pwm-cells = 2 will continue to work.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Since we now have ->apply(), these are no longer relevant.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

In preparation for supporting setting the polarity, switch the driver
to support the ->apply() method.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Now that sun4i PWM driver supports deasserting reset line and enabling
bus clock, support for H6 PWM can be added.

Note that while H6 PWM has two channels, only first one is wired to
output pin. Second channel is used as a clock source to companion AC200
chip which is bundled into same package.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

PWM core has an option to bypass whole logic and output unchanged source
clock as PWM output. This is achieved by enabling bypass bit.

Note that when bypass is enabled, no other setting has any meaning, not
even enable bit.

This mode of operation is needed to achieve high enough frequency to
serve as clock source for AC200 chip which is integrated into same
package as H6 SoC.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Bypass mode will require to be re-calculated when the pwm state
is changed.

Remove the condition so pwm_sun4i_calculate is always called.
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

H6 PWM core needs bus clock to be enabled in order to work.

Add an optional probe for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

New device tree bindings called the source clock of the module
"mod" when several clocks are defined.

Try to get a clock called "mod" if nothing is found try to get
an unnamed clock.
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

H6 PWM core needs deasserted reset line in order to work.

Add an optional probe for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

The i.MX driver currently uses a shortcut and doesn't write all of the
state through to the hardware when the PWM is disabled. This causes an
inconsistent state to be read back by consumers with the result of them
malfunctioning.

Fix this by always writing the full state through to the hardware
registers so that the correct state can always be read back.
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

The hardware register containing the duty cycle value cannot be accessed
when the PWM is disabled. This causes the ->get_state() callback to read
back a duty cycle value of 0, which can confuse consumer drivers.
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

The ChromeOS embedded controller doesn't differentiate between disabled
and duty cycle being 0. In order not to potentially confuse consumers,
cache the duty cycle and return the cached value instead of the real
value when the PWM is disabled.
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Drivers that support reading the hardware state (using ->get_state())
may want to rely on per-PWM data to do so. Defer reading the hardware
state for the first time until the PWM has been requested and after
drivers have had a chance to allocate per-PWM data.

Conceptually this is also a more natural place to read the hardware
state because the PWM core doesn't need to know the hardware state of a
PWM unless there is a user for it. This also ensures that the state is
read everytime a user requests a PWM. If the PWM changes between users
for some reason, the PWM core will reload the state from hardware and
keep its copy of the state up-to-date.
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Pull networking fixes from David Miller:

 1) More jumbo frame fixes in r8169, from Heiner Kallweit.

 2) Fix bpf build in minimal configuration, from Alexei Starovoitov.

 3) Use after free in slcan driver, from Jouni Hogander.

 4) Flower classifier port ranges don't work properly in the HW offload
    case, from Yoshiki Komachi.

 5) Use after free in hns3_nic_maybe_stop_tx(), from Yunsheng Lin.

 6) Out of bounds access in mqprio_dump(), from Vladyslav Tarasiuk.

 7) Fix flow dissection in dsa TX path, from Alexander Lobakin.

 8) Stale syncookie timestampe fixes from Guillaume Nault.

[ Did an evil merge to silence a warning introduced by this pull - Linus ]

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
  r8169: fix rtl_hw_jumbo_disable for RTL8168evl
  net_sched: validate TCA_KIND attribute in tc_chain_tmplt_add()
  r8169: add missing RX enabling for WoL on RTL8125
  vhost/vsock: accept only packets with the right dst_cid
  net: phy: dp83867: fix hfs boot in rgmii mode
  net: ethernet: ti: cpsw: fix extra rx interrupt
  inet: protect against too small mtu values.
  gre: refetch erspan header from skb->data after pskb_may_pull()
  pppoe: remove redundant BUG_ON() check in pppoe_pernet
  tcp: Protect accesses to .ts_recent_stamp with {READ,WRITE}_ONCE()
  tcp: tighten acceptance of ACKs not matching a child socket
  tcp: fix rejected syncookies due to stale timestamps
  lpc_eth: kernel BUG on remove
  tcp: md5: fix potential overestimation of TCP option space
  net: sched: allow indirect blocks to bind to clsact in TC
  net: core: rename indirect block ingress cb function
  net-sysfs: Call dev_hold always in netdev_queue_add_kobject
  net: dsa: fix flow dissection on Tx path
  net/tls: Fix return values to avoid ENOTSUPP
  net: avoid an indirect call in ____sys_recvmsg()
  ...

Pull more SCSI updates from James Bottomley:
 "Eleven patches, all in drivers (no core changes) that are either minor
  cleanups or small fixes.

  They were late arriving, but still safe for -rc1"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: MAINTAINERS: Add the linux-scsi mailing list to the ISCSI entry
  scsi: megaraid_sas: Make poll_aen_lock static
  scsi: sd_zbc: Improve report zones error printout
  scsi: qla2xxx: Fix qla2x00_request_irqs() for MSI
  scsi: qla2xxx: unregister ports after GPN_FT failure
  scsi: qla2xxx: fix rports not being mark as lost in sync fabric scan
  scsi: pm80xx: Remove unused include of linux/version.h
  scsi: pm80xx: fix logic to break out of loop when register value is 2 or 3
  scsi: scsi_transport_sas: Fix memory leak when removing devices
  scsi: lpfc: size cpu map by last cpu id set
  scsi: ibmvscsi_tgt: Remove unneeded variable rc