This patch adds the audio subsystem clock controller and the I2S
IP block nodes for Exynos4 SoC series.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch fixed gpio key device node.
First, fix incorrect gpio property.
And then, add ok-key node where locate bottom center.
I have tested on exynos4412-trats2 board.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Exynos4412-trats2 board have light/proximity sensor.
This patch add cm36651 light/ proximity sensor node for exynos4412.
cm36651 is required properties as below.
- Use i2c-gpio for cm36651 sensor.
- Use fixed regulator for the IR LED.
  It is a part of the cm36651 for proximity detection.
- cm36651 is i2c device driver so need to use i2c-gpio driver.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add required device node for ehci and ohci controllers to
enable USB 2.0 support.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add required device node for usb2phy to let enable USB 2.0
support.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add support to PHY of USB2 of the Exynos5250 SoC.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
[gautam.vivek@samsung.com: Split the usb phy entries]
[gautam.vivek@samsung.com: Added phy entry for OHCI also along with EHCI]
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch adds sysreg-syscon node to exynos5250 and exynos5420 device
tree, to access System Register's registers using syscon driver.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
[gautam.vivek@samsung.com: Split this syreg-syscon dts entry]
[gautam.vivek@samsung.com: added similar syscon entry for exynos5420]
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
[vikas.sajjan@samsung.com: updated the binding document]
Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

DP Hpd Gpio pin which is "gpx2-6" in Exynos 5420 based peach board,
belongs to Pinctrl_0. It has moved to pinctrl_0 from pinctrl_3.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add MFC memory banks to Exynos5420 based SMDK and Arndale-octa boards.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Enable dp-controller for peach-pit board.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Enable fimd for peach-pit board.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Enable dp-controller for snow board.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Enable fimd node for snow board.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add PWM backlight node for exynos5250 based snow board.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Adds the PWM nodes to 5250 pinctrl dtsi file.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add required fixed-regulator for VBUS supply for USB 3.0
controller phy.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add required fixed-regulator for VBUS supply for USB 3.0
controller phy.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add required fixed-regulator for VBUS supply for USB 3.0
controller phy.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

PD entry was missing in MFC codec node.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by : Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

The audio setup on Peach-pit board is similar to Snow board, hence the
sound-card driver used on Snow board can be reused on Peach-pit board.

Peach-pit board uses MAX98090 audio codec.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

The audio codec on Snow board, MAX98095 is connected on I2C7 bus.
Also it requires the GPX1-7 line to be pulled up.

Updated Snow DTS file to incorporate above changes and added a
sound node to instantiate the I2S-based sound card.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Removing the dt node for older usb3 phy driver from Exynos5250
device tree and updating the dt node for DWC3 controller to
use new phy driver based on generic phy framework.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add device tree node for new usbdrd-phy driver, which
is based on generic phy framework.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add device tree nodes for DWC3 controller present on
Exynos 5420 SoC, to enable support for USB 3.0.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add device tree nodes for USB 3.0 PHY present alongwith
USB 3.0 controller Exynos 5420 SoC. This phy driver is
based on generic phy framework.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Enable hdmi for exynos5420 based peach-pit board.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Replace compatible string for HDMI node in Exynos5420. Since
latest restructring in Drm hdmi driver, it is agreed to use
a seperate compatible string for Exynos5420 HDMI IP siince it
uses APB mapped Phy.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Enable support for HDMI for exynos5250 based Snow board.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Added TPS65090 regulator related nodes to Snow board.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Added pinctrl node for embedded controller (EC) IRQ
on Snow board.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Added i2c-arbitrator pinctrl node to Snow board.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add SRAM binding documentation.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
[kgene.kim@samsung.com: changed name SRAM to SYSRAM]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Instead of hardcoding the SYSRAM details for each SoC,
pass this information through device tree (DT) and make
the code SoC agnostic. Generic DT SRAM bindings are
used for achieving this.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Adds the google peach-pit board dts file which uses
exynos5420 SoC.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Adding labels to nodes which do not have it yet in exynos5420.
This is done so as to use reference based node updation in board
files.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Adds the PWM nodes to 5420 pinctrl dtsi file.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch enables the rear facing camera (s5c73m3) on TRATS2 board
by adding the I2C0 bus controller, s5c73m3 sensor, MIPI CSI-2 receiver
and the sensor's voltage regulator supply nodes.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Remove unused /camera/clock-controller node and add required clock
properties to the camera node. This is required for a clock provider
that will be referenced by image sensor devices.
Also add required clock related changes to s5k6a3 device node and
afvdd regulator supply.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

The i2c_ak8975 controller uses label i2c8.
This alias is already used for I2C controller 8 defined
in file arch/arm/boot/dts/exynos4.dtsi.

This patch renames a label for i2c_ak8975 to i2c9.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch adds missing pinctrls for I2C controllers 2-7.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>