- 26 Feb, 2018 20 commits
-
-
Finn Thain authored
Eliminate duplicated debug code by moving it into the core driver. Don't log the only valid silicon revision number (it's in the source). Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Chris Zankel <chris@zankel.net> Tested-by:
Stan Johnson <userm57@yahoo.com> Signed-off-by:
Finn Thain <fthain@telegraphics.com.au> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Finn Thain authored
Add missing printk severity levels by adopting pr_foo() calls for the platform_driver and dev_foo() calls for the nubus_driver. Avoid KERN_CONT usage as per advice from checkpatch. Avoid #ifdef around printk calls. Don't log driver probe messages after calling register_netdev(). Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Chris Zankel <chris@zankel.net> Tested-by:
-
Finn Thain authored
The MACH_IS_MAC test is redundant here because the platform device won't get registered unless MACH_IS_MAC. Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
Finn Thain authored
This resolves an old issue preventing any NuBus SONIC NICs from working in a Mac with an on-board SONIC device. Tested-by:
-
Sergei Shtylyov authored
It appears that the single port Ether controllers having TSU (like SH7734/ R8A7740) need the same kind of treating in sh_eth_tsu_init() as R7S72100 currently has -- they also don't have the TSU registers related e.g. to passing the frames between ports. Add the 'sh_eth_cpu_data::dual_port' flag and use it as a new criterion for taking a "short path" in the TSU init sequence in order to avoid writing to the non-existent registers... Fixes: f0e81fec ("net: sh_eth: Add support SH7734") Fixes: 73a0d907 ("net: sh_eth: add support R8A7740") Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Tested-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
-
Sergei Shtylyov authored
The TSU_QTAG0/1 registers found in the Gigabit Ether controllers actually have the same long name as the TSU_QTAGM0/1 registers in the early Ether controllers: Qtag Addition/Deletion Set Register (Port 0/1 to 1/0); thus there's no need to make a difference in sh_eth_tsu_init() between those controllers. Unfortunately, we can't just remove TSU_QTAG0/1 from the register *enum* because that would break the ethtool register dump... Fixes: b0ca2a21 ("sh_eth: Add support of SH7763 to sh_eth") Signed-off-by:
-
BTaskaya authored
This patch converts old type string formattings to new type string formattings for adapting Linux Traffic Control (tc) unit testing suite python3. Linux Traffic Control (tc) unit testing suite's code quality improved is improved with this patch. According to python documentation; "The built-in string class provides the ability to do complex variable substitutions and value formatting via the format() method described in PEP 3101. " but the project was using old type formattings and new type string formattings together, this patch's main purpose is converting all old types to new types. Following files changed: 1. tools/testing/selftests/tc-testing/tdc.py 2. tools/testing/selftests/tc-testing/tdc_batch.py Following PEP rules applied: 1. PEP8 - Code Styling 2. PEP3101 - Advanced Code Formatting Signed-off-by:
Batuhan Osman Taskaya <batuhanosmantaskaya@gmail.com> Signed-off-by:
-
Colin Ian King authored
The function xenvif_rx_skb is local to the source and does not need to be in global scope, so make it static. Cleans up sparse warning: drivers/net/xen-netback/rx.c:422:6: warning: symbol 'xenvif_rx_skb' was not declared. Should it be static? Signed-off-by:
Colin Ian King <colin.king@canonical.com> Acked-by:
Wei Liu <wei.liu2@citrix.com> Signed-off-by:
-
David S. Miller authored
Brenda J. Butler says: ==================== tools: tc-testing: better error reporting This patch set contains a bit of cleanup and better error reporting, esp. in pre- and post-suite, and pre- and post-case commands. ==================== Signed-off-by: -
Brenda J. Butler authored
Do a better job with error handling - in pre- and post-suite, in pre- and post-case. Show a traceback for errors. Signed-off-by:
Brenda J. Butler <bjb@mojatatu.com> Signed-off-by:
-
Brenda J. Butler authored
Signed-off-by:
-
Colin Ian King authored
Bit pattern LOOPBACK_SGMII is being bit-wise or'd twice; remove the redundant 2nd LOOPBACK_SGMII Signed-off-by:
-
Arnd Bergmann authored
gcc warns that 'resource_id' is not initialized if we don't come though any of the three 'case' statements before: drivers/net/ethernet/mellanox/mlxsw/spectrum_kvdl.c: In function 'mlxsw_sp_kvdl_part_init': drivers/net/ethernet/mellanox/mlxsw/spectrum_kvdl.c:275:8: error: 'resource_id' may be used uninitialized in this function [-Werror=maybe-uninitialized] In the current code, that won't happen, but it's more robust to explicitly handle this by returning a failure from mlxsw_sp_kvdl_part_init. Fixes: 887839e6 ("mlxsw: spectrum_kvdl: Add support for dynamic partition set") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Arkadi Sharshevsky <arkadis@mellanox.com> Signed-off-by:
-
Arnd Bergmann authored
Calculating the number of entries now uses 64-bit arithmetic that causes a link error on 32-bit architectures: drivers/net/ethernet/mellanox/mlxsw/spectrum_kvdl.o: In function `mlxsw_sp_kvdl_init': spectrum_kvdl.c:(.text+0x51c): undefined reference to `__aeabi_uldivmod' We could probably use a 32-bit division here as before, but since this is not in a performance critical path, div_u64() seems cleaner here. Fixes: 887839e6 ("mlxsw: spectrum_kvdl: Add support for dynamic partition set") Signed-off-by:
-
David S. Miller authored
Andrew Lunn says: ==================== mv88e6xxx: Poll when no interrupt defined Not all boards using the mv88e6xxx switches have the interrupt output connected to a GPIO. On these boards phylib has to poll the PHYs, rather than use interrupts. Have the driver poll the interrupt status register, which is more efficient than having phylib do it. And it enables other switch interrupts to be services. The Armada 370RD is such a board without a interrupt GPIO. Now that interrupts work, wire up the PHYs to make use if them. ==================== Signed-off-by: -
Andrew Lunn authored
The Ethernet switch has an embedded interrupt controller. Interrupts from the embedded PHYs are part of this interrupt controller. Explicitly list the MDIO bus the embedded PHYs are on, and wire up the interrupts. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Andrew Lunn authored
Not all boards have the interrupt output from the switch connected to a GPIO line. In such cases, phylib has to poll the internal PHYs, rather than receive an interrupt when there is a change in the link state. phylib polls once per second, and per PHY reads around 4 words. With a switch typically having 4 internal PHYs, this means 16 MDIO transactions per second. Rather than performing this phylib level polling, have the driver poll the interrupt status register. If the status register indicates an interrupt condition processing of interrupts in the same way as if a GPIO was used. Polling 10 times a second places less load on the MDIO bus. But rather than taking on average 0.5s to detect a link change, it takes less than 0.05s. Additionally, other interrupts, such as the watchdog, ATU and VTU violations will be reported. Signed-off-by:
-
Ido Schimmel authored
Up until now we only allowed VLAN devices to be put in a VLAN-unaware bridge, but some users need the ability to enslave physical ports as well. This is achieved by mapping the port and VID 1 to the bridge's vFID, instead of the port and the VID used by the VLAN device. The above is valid because as long as the port is not enslaved to a bridge, VID 1 is guaranteed to be configured as PVID and egress untagged. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Tested-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-nextDavid S. Miller authored
Daniel Borkmann says: ==================== pull-request: bpf-next 2018-02-26 The following pull-request contains BPF updates for your *net-next* tree. The main changes are: 1) Various improvements for BPF kselftests: i) skip unprivileged tests when kernel.unprivileged_bpf_disabled sysctl knob is set, ii) count the number of skipped tests from unprivileged, iii) when a test case had an unexpected error then print the actual but also the unexpected one for better comparison, from Joe. 2) Add a sample program for collecting CPU state statistics with regards to how long the CPU resides in cstate and pstate levels. Based on cpu_idle and cpu_frequency trace points, from Leo. 3) Various x64 BPF JIT optimizations to further shrink the generated image size in order to make it more icache friendly. When tested on the Cilium generated programs, image size reduced by approx 4-5% in best case mainly due to how LLVM emits unsigned 32 bit constants, from Daniel. 4) Improvements and fixes on the BPF sockmap sample programs: i) fix the sockmap's Makefile to include nlattr.o for libbpf, ii) detach the sock ops programs from the cgroup before exit, from Prashant. 5) Avoid including xdp.h in filter.h by just forward declaring the struct xdp_rxq_info in filter.h, from Jesper. 6) Fix the BPF kselftests Makefile for cgroup_helpers.c by only declaring it a dependency for test_dev_cgroup.c but not every other test case where it is not needed, from Jesper. 7) Adjust rlimit RLIMIT_MEMLOCK for test_tcpbpf_user selftest since the default is insufficient for creating the 'global_map' used in the corresponding BPF program, from Yonghong. 8) Likewise, for the xdp_redirect sample, Tushar ran into the same when invoking xdp_redirect and xdp_monitor at the same time, therefore in order to have the sample generically work bump the limit here, too. Fix from Tushar. 9) Avoid an unnecessary NULL check in BPF_CGROUP_RUN_PROG_INET_SOCK() since sk is always guaranteed to be non-NULL, from Yafang. ==================== Signed-off-by: -
Leo Yan authored
CPU is active when have running tasks on it and CPUFreq governor can select different operating points (OPP) according to different workload; we use 'pstate' to present CPU state which have running tasks with one specific OPP. On the other hand, CPU is idle which only idle task on it, CPUIdle governor can select one specific idle state to power off hardware logics; we use 'cstate' to present CPU idle state. Based on trace events 'cpu_idle' and 'cpu_frequency' we can accomplish the duration statistics for every state. Every time when CPU enters into or exits from idle states, the trace event 'cpu_idle' is recorded; trace event 'cpu_frequency' records the event for CPU OPP changing, so it's easily to know how long time the CPU stays in the specified OPP, and the CPU must be not in any idle state. This patch is to utilize the mentioned trace events for pstate and cstate statistics. To achieve more accurate profiling data, the program uses below sequence to insure CPU running/idle time aren't missed: - Before profiling the user space program wakes up all CPUs for once, so can avoid to missing account time for CPU staying in idle state for long time; the program forces to set 'scaling_max_freq' to lowest frequency and then restore 'scaling_max_freq' to highest frequency, this can ensure the frequency to be set to lowest frequency and later after start to run workload the frequency can be easily to be changed to higher frequency; - User space program reads map data and update statistics for every 5s, so this is same with other sample bpf programs for avoiding big overload introduced by bpf program self; - When send signal to terminate program, the signal handler wakes up all CPUs, set lowest frequency and restore highest frequency to 'scaling_max_freq'; this is exactly same with the first step so avoid to missing account CPU pstate and cstate time during last stage. Finally it reports the latest statistics. The program has been tested on Hikey board with octa CA53 CPUs, below is one example for statistics result, the format mainly follows up Jesper Dangaard Brouer suggestion. Jesper reminds to 'get printf to pretty print with thousands separators use %' and setlocale(LC_NUMERIC, "en_US")', tried three different arm64 GCC toolchains (5.4.0 20160609, 6.2.1 20161016, 6.3.0 20170516) but all of them cannot support printf flag character %' on arm64 platform, so go back print number without grouping mode. CPU states statistics: state(ms) cstate-0 cstate-1 cstate-2 pstate-0 pstate-1 pstate-2 pstate-3 pstate-4 CPU-0 767 6111 111863 561 31 756 853 190 CPU-1 241 10606 107956 484 125 646 990 85 CPU-2 413 19721 98735 636 84 696 757 89 CPU-3 84 11711 79989 17516 909 4811 5773 341 CPU-4 152 19610 98229 444 53 649 708 1283 CPU-5 185 8781 108697 666 91 671 677 1365 CPU-6 157 21964 95825 581 67 566 684 1284 CPU-7 125 15238 102704 398 20 665 786 1197 Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Vincent Guittot <vincent.guittot@linaro.org> Signed-off-by:
Leo Yan <leo.yan@linaro.org> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net>
-
- 24 Feb, 2018 8 commits
-
-
Alexei Starovoitov authored
Daniel Borkmann says: ==================== Couple of minor improvements to the x64 JIT I had still around from pre merge window in order to shrink the image size further. Added test cases for kselftests too as well as running Cilium workloads on them w/o issues. ==================== Signed-off-by:Alexei Starovoitov <ast@kernel.org>
-
Daniel Borkmann authored
Add few test cases that check the rnu-time results under JIT. Signed-off-by:
-
Daniel Borkmann authored
While it's rather cumbersome to reduce prologue for cBPF->eBPF migrations wrt spill/fill for r15 which is callee saved register due to bpf_error path in bpf_jit.S that is both used by migrations as well as native eBPF, we can still trivially save 5 bytes in prologue for the former since tail calls can never be used there. cBPF->eBPF migrations also have their own custom prologue in BPF asm that xors A and X reg anyway, so it's fine we skip this here. Signed-off-by:
-
Daniel Borkmann authored
Add a generic emit_mov_reg() helper in order to reuse it in BPF multiplication to load the src into rax, we can save a few bytes in alu32 while doing so. Signed-off-by:
-
Daniel Borkmann authored
Instead of unconditionally performing push/pop on rax/rdx in case of multiplication, we can save a few bytes in case of dest register being either BPF r0 (rax) or r3 (rdx) since the result is written in there anyway. Signed-off-by:
-
Daniel Borkmann authored
While analyzing some of the more complex BPF programs from Cilium, I found that LLVM generally prefers to emit LD_IMM64 instead of MOV32 BPF instructions for loading unsigned 32-bit immediates into a register. Given we cannot change the current/stable LLVM versions that are already out there, lets optimize this case such that the JIT prefers to emit 'mov %eax, imm32' over 'movabsq %rax, imm64' whenever suitable in order to reduce the image size by 4-5 bytes per such load in the typical case, reducing image size on some of the bigger programs by up to 4%. emit_mov_imm32() and emit_mov_imm64() have been added as helpers. Signed-off-by:
-
Daniel Borkmann authored
When we shift by one, we can use a different encoding where imm is not explicitly needed, which saves 1 byte per such op. Signed-off-by:
-
-
- 23 Feb, 2018 12 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Fix TTL offset calculation in mac80211 mesh code, from Peter Oh. 2) Fix races with procfs in ipt_CLUSTERIP, from Cong Wang. 3) Memory leak fix in lpm_trie BPF map code, from Yonghong Song. 4) Need to use GFP_ATOMIC in BPF cpumap allocations, from Jason Wang. 5) Fix potential deadlocks in netfilter getsockopt() code paths, from Paolo Abeni. 6) Netfilter stackpointer size checks really are needed to validate user input, from Florian Westphal. 7) Missing timer init in x_tables, from Paolo Abeni. 8) Don't use WQ_MEM_RECLAIM in mac80211 hwsim, from Johannes Berg. 9) When an ibmvnic device is brought down then back up again, it can be sent queue entries from a previous session, handle this properly instead of crashing. From Thomas Falcon. 10) Fix TCP checksum on LRO buffers in mlx5e, from Gal Pressman. 11) When we are dumping filters in cls_api, the output SKB is empty, and the filter we are dumping is too large for the space in the SKB, we should return -EMSGSIZE like other netlink dump operations do. Otherwise userland has no signal that is needs to increase the size of its read buffer. From Roman Kapl. 12) Several XDP fixes for virtio_net, from Jesper Dangaard Brouer. 13) Module refcount leak in netlink when a dump start fails, from Jason Donenfeld. 14) Handle sub-optimal GSO sizes better in TCP BBR congestion control, from Eric Dumazet. 15) Releasing bpf per-cpu arraymaps can take a long time, add a condtional scheduling point. From Eric Dumazet. 16) Implement retpolines for tail calls in x64 and arm64 bpf JITs. From Daniel Borkmann. 17) Fix page leak in gianfar driver, from Andy Spencer. 18) Missed clearing of estimator scratch buffer, from Eric Dumazet. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits) net_sched: gen_estimator: fix broken estimators based on percpu stats gianfar: simplify FCS handling and fix memory leak ipv6 sit: work around bogus gcc-8 -Wrestrict warning macvlan: fix use-after-free in macvlan_common_newlink() bpf, arm64: fix out of bounds access in tail call bpf, x64: implement retpoline for tail call rxrpc: Fix send in rxrpc_send_data_packet() net: aquantia: Fix error handling in aq_pci_probe() bpf: fix rcu lockdep warning for lpm_trie map_free callback bpf: add schedule points in percpu arrays management regulatory: add NUL to request alpha2 ibmvnic: Fix early release of login buffer net/smc9194: Remove bogus CONFIG_MAC reference net: ipv4: Set addr_type in hash_keys for forwarded case tcp_bbr: better deal with suboptimal GSO smsc75xx: fix smsc75xx_set_features() netlink: put module reference if dump start fails selftests/bpf/test_maps: exit child process without error in ENOMEM case selftests/bpf: update gitignore with test_libbpf_open selftests/bpf: tcpbpf_kern: use in6_* macros from glibc .. -
Linus Torvalds authored
Merge branch 'fixes-v4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security Pull security subsystem fixes from James Morris: - keys fixes via David Howells: "A collection of fixes for Linux keyrings, mostly thanks to Eric Biggers: - Fix some PKCS#7 verification issues. - Fix handling of unsupported crypto in X.509. - Fix too-large allocation in big_key" - Seccomp updates via Kees Cook: "These are fixes for the get_metadata interface that landed during -rc1. While the new selftest is strictly not a bug fix, I think it's in the same spirit of avoiding bugs" - an IMA build fix from Randy Dunlap * 'fixes-v4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: integrity/security: fix digsig.c build error with header file KEYS: Use individual pages in big_key for crypto buffers X.509: fix NULL dereference when restricting key with unsupported_sig X.509: fix BUG_ON() when hash algorithm is unsupported PKCS#7: fix direct verification of SignerInfo signature PKCS#7: fix certificate blacklisting PKCS#7: fix certificate chain verification seccomp: add a selftest for get_metadata ptrace, seccomp: tweak get_metadata behavior slightly seccomp, ptrace: switch get_metadata types to arch independent
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linuxLinus Torvalds authored
Pull arm64 fixes from Catalin Marinas: "arm64 and perf fixes: - build error when accessing MPIDR_HWID_BITMASK from .S - fix CTR_EL0 field definitions - remove/disable some kernel messages on user faults (unhandled signals, unimplemented syscalls) - fix kernel page fault in unwind_frame() with function graph tracing - fix perf sleeping while atomic errors when booting with ACPI" * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: arm64: fix unwind_frame() for filtered out fn for function graph tracing arm64: Enforce BBM for huge IO/VMAP mappings arm64: perf: correct PMUVer probing arm_pmu: acpi: request IRQs up-front arm_pmu: note IRQs and PMUs per-cpu arm_pmu: explicitly enable/disable SPIs at hotplug arm_pmu: acpi: check for mismatched PPIs arm_pmu: add armpmu_alloc_atomic() arm_pmu: fold platform helpers into platform code arm_pmu: kill arm_pmu_platdata ARM: ux500: remove PMU IRQ bouncer arm64: __show_regs: Only resolve kernel symbols when running at EL1 arm64: Remove unimplemented syscall log message arm64: Disable unhandled signal log messages by default arm64: cpufeature: Fix CTR_EL0 field definitions arm64: uaccess: Formalise types for access_ok() arm64: Fix compilation error while accessing MPIDR_HWID_BITMASK from .S files -
git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mipsLinus Torvalds authored
Pull MIPS fix from James Hogan: "A single MIPS fix for mismatching struct compat_flock, resulting in bus errors starting Firefox on Debian 8 since 4.13" * tag 'mips_fixes_4.16_3' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips: MIPS: Drop spurious __unused in struct compat_flock
-
git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printkLinus Torvalds authored
Pull printk fixlet from Petr Mladek: "People expect to see the real pointer value for %px. Let's substitute '(null)' only for the other %p? format modifiers that need to deference the pointer" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk: vsprintf: avoid misleading "(null)" for %px
-
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linuxLinus Torvalds authored
Pull i2c fixes from Wolfram Sang: "Two bugfixes, one v4.16 regression fix, and two documentation fixes" * 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: designware: Consider SCL GPIO optional i2c: busses: i2c-sirf: Fix spelling: "formular" -> "formula". i2c: bcm2835: Set up the rising/falling edge delays i2c: i801: Add missing documentation entries for Braswell and Kaby Lake i2c: designware: must wait for enable
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds authored
Pull SCSI fixes from James Bottomley: "These are mostly fixes for problems with merge window code. In addition we have one doc update (alua) and two dead code removals (aiclib and octogon) a spurious assignment removal (csiostor) and a performance improvement for storvsc involving better interrupt spreading and increasing the command per lun handling" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: qla4xxx: skip error recovery in case of register disconnect. scsi: aacraid: fix shutdown crash when init fails scsi: qedi: Cleanup local str variable scsi: qedi: Fix truncation of CHAP name and secret scsi: qla2xxx: Fix incorrect handle for abort IOCB scsi: qla2xxx: Fix double free bug after firmware timeout scsi: storvsc: Increase cmd_per_lun for higher speed devices scsi: qla2xxx: Fix a locking imbalance in qlt_24xx_handle_els() scsi: scsi_dh: Document alua_rtpg_queue() arguments scsi: Remove Makefile entry for oktagon files scsi: aic7xxx: remove aiclib.c scsi: qla2xxx: Avoid triggering undefined behavior in qla2x00_mbx_completion() scsi: mptfusion: Add bounds check in mptctl_hp_targetinfo() scsi: sym53c8xx_2: iterator underflow in sym_getsync() scsi: bnx2fc: Fix check in SCSI completion handler for timed out request scsi: csiostor: remove redundant assignment to pointer 'ln' scsi: ufs: Enable quirk to ignore sending WRITE_SAME command scsi: ibmvfc: fix misdefined reserved field in ibmvfc_fcp_rsp_info scsi: qla2xxx: Fix memory corruption during hba reset test scsi: mpt3sas: fix an out of bound write
-
Donald Sharp authored
For ages iproute2 has used `struct rtmsg` as the ancillary header for FIB rules and in the process set the protocol value to RTPROT_BOOT. Until ca56209a66 ("net: Allow a rule to track originating protocol") the kernel rules code ignored the protocol value sent from userspace and always returned 0 in notifications. To avoid incompatibility with existing iproute2, send the protocol as a new attribute. Fixes: cac56209 ("net: Allow a rule to track originating protocol") Signed-off-by:Donald Sharp <sharpd@cumulusnetworks.com> Signed-off-by:
-
git://people.freedesktop.org/~airlied/linuxLinus Torvalds authored
Pull drm fixes from Dave Airlie: "A bunch of fixes for rc3: Exynos: - fixes for using monotonic timestamps - register definitions - removal of unused file ipu-v3L - minor changes - make some register arrays const+static - fix some leaks meson: - fix for vsync atomic: - fix for memory leak EDID parser: - add quirks for some more non-desktop devices - 6-bit panel fix. drm_mm: - fix a bug in the core drm mm hole handling cirrus: - fix lut loading regression Lastly there is a deadlock fix around runtime suspend for secondary GPUs. There was a deadlock between one thread trying to wait for a workqueue job to finish in the runtime suspend path, and the workqueue job it was waiting for in turn waiting for a runtime_get_sync to return. The fixes avoids it by not doing the runtime sync in the workqueue as then we always wait for all those tasks to complete before we runtime suspend" * tag 'drm-fixes-for-v4.16-rc3' of git://people.freedesktop.org/~airlied/linux: (25 commits) drm/tve200: fix kernel-doc documentation comment include drm/edid: quirk Sony PlayStation VR headset as non-desktop drm/edid: quirk Windows Mixed Reality headsets as non-desktop drm/edid: quirk Oculus Rift headsets as non-desktop drm/meson: fix vsync buffer update drm: Handle unexpected holes in color-eviction drm: exynos: Use proper macro definition for HDMI_I2S_PIN_SEL_1 drm/exynos: remove exynos_drm_rotator.h drm/exynos: g2d: Delete an error message for a failed memory allocation in two functions drm/exynos: fix comparison to bitshift when dealing with a mask drm/exynos: g2d: use monotonic timestamps drm/edid: Add 6 bpc quirk for CPT panel in Asus UX303LA gpu: ipu-csi: add 10/12-bit grayscale support to mbus_code_to_bus_cfg gpu: ipu-cpmem: add 16-bit grayscale support to ipu_cpmem_set_image gpu: ipu-v3: prg: fix device node leak in ipu_prg_lookup_by_phandle gpu: ipu-v3: pre: fix device node leak in ipu_pre_lookup_by_phandle drm/amdgpu: Fix deadlock on runtime suspend drm/radeon: Fix deadlock on runtime suspend drm/nouveau: Fix deadlock on runtime suspend drm: Allow determining if current task is output poll worker ...
-
Willem de Bruijn authored
The packet fanout test generates UDP traffic and reads this with a pair of packet sockets, testing the various fanout algorithms. Avoid non-determinism from reading unrelated background traffic. Fanout decisions are made before unrelated packets can be dropped with a filter, so that is an insufficient strategy [*]. Run the packet socket tests in a network namespace, similar to msg_zerocopy. It it still good practice to install a filter on a packet socket before accepting traffic. Because this is example code, demonstrate that pattern. Open the socket initially bound to no protocol, install a filter, and only then bind to ETH_P_IP. Another source of non-determinism is hash collisions in FANOUT_HASH. The hash function used to select a socket in the fanout group includes the pseudorandom number hashrnd, which is not visible from userspace. To work around this, the test tries to find a pair of UDP source ports that do not collide. It gives up too soon (5 times, every 32 runs) and output is confusing. Increase tries to 20 and revise the error msg. [*] another approach would be to add a third socket to the fanout group and direct all unexpected traffic here. This is possible only when reimplementing methods like RR or HASH alongside this extra catch-all bucket, using the BPF fanout method. Signed-off-by:Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Colin Ian King authored
Zero is being bit-wise or'd in a calculation twice; these are redundant and can be removed. Signed-off-by:
-
Eric Dumazet authored
pfifo_fast got percpu stats lately, uncovering a bug I introduced last year in linux-4.10. I missed the fact that we have to clear our temporary storage before calling __gnet_stats_copy_basic() in the case of percpu stats. Without this fix, rate estimators (tc qd replace dev xxx root est 1sec 4sec pfifo_fast) are utterly broken. Fixes: 1c0d32fd ("net_sched: gen_estimator: complete rewrite of rate estimators") Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
