Add the Wakeup M3 IPC node for the wkup_m3_ipc driver on AM33xx SoCs.
This node uses the IPC registers, part of the Control Module, and is
therefore added as a child of the scm node.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This region contains CTRL_CORE_SMA_SW2..9 registers which
are not specific to any domain and can be reasonably
accessed via syscon driver.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We need to add 4 bytes to include the last 32-bit register space.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

These nodes are wrongly placed. They must come under the
scm node. Nobody uses them either so get rid of them.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add interrupt names so that the same can be used for OTG easily.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add interrupt names so that the same can be used for OTG easily.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add interrupt names so that the same can be used for OTG easily.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Similar to commit fdf4850c ("ARM: BCM5301X: workaround suppress fault"),
let's add custom handling for the aborts on t410 that prevent booting:

Unhandled fault: imprecise external abort (0xc06) at 0xee091fb0
pgd = ee4bc000
[ee091fb0] *pgd=ae00041e(bad)
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000007

Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add minimal support for HP T410.

Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add minimal dts support for dm8148-evm.

Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use fixed clocks until we have a clock driver for the PLL.
The mux and divider composite clocks work the same way
as on dm816x and am335x.

Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add minimal dm814x support.

Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add wl1251 support via pdata-quirks as it's driver lacks DT
support. MMC3 is marked disabled in DT so that MMC3 instance of
hsmmc driver is probed using platform data with special card init
callback.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add backlight support via pdata-quirks as it's driver lacks DT support.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This adds missing bits for EHCI HS USB host support and 32k clock
buffer control for the wg7210 bt+wifi module.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

- add pandora specific compatible name
- fix mmc2 card detect polarity
- fix mmc1 and mmc2 write protect polarity
- disable write protect pins because of production issue and add an
  explanation why they are disabled
- fix NAND partition name to reflect the correct address
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Palmas on OMAP5uevm has support for power button, so enable it.
Signed-off-by: Aparna Balasubramanian <aparnab@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add serialN aliases for all 6 UART instances on
the AM437x SoC so each board's .dts file does not
have to define its own aliases.

Remove the alias added for am437x-gp-evm.dts now
that we have the aliases defined in am4372.dtsi
file.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

phyBOARD-WEGA-AM335x represents a direct soldered
combination of a phyCORE-AM335x SoM and carrier board.

Different kind of SoM options can be connected to
the wega carrier board. So we created a separate
wega dtsi file. The final dts contains the actual
SoM on the carrier board.

WEGA carrier board features:
* ETH phy on carrier board: 1x MII
* 1x CAN
* 2x UART
* USB0 (device)
* USB1 (host)
* mSD slot
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

phyCORE-AM335x is a SoM (System on Module) containing
a AM335x SOC. The module can be connected to different
carrier boards.

Some hardware parts are configurable on the phyCORE-AM335x.
So they are disabled on default in this som dtsi file.
They will be enabled in the board dts files, when populated.

* RAM up to 1GiB
* PMIC
* NAND flash up to 1GiB
* Eth PHY on SOM: 1x RMII
* SPI NOR flash 8MiB (optional)
* i2c RTC (optional)
* i2c EEPROM 4kiB (optional)
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

In tsc2046 touch driver, the values such as ti,x-min is defined as a u16
value. the driver use API of_property_read_u16() read the value. For these
u16 value, the dts entry should be like:
	property = /bits/ 16 <0x5000>;
This describes the property as a u16 value.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The sound support consist only Headset output on the board and can be
handled by "simple-audio-card"
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

When McASP is not in use the pins can be put to sleep mode to conserve
power.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use mcasp1_pins as name for the pinctrl section needed for McASP1 instead
of the am335x_evm_audio_pins name.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The section had two tabs instead of one.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The sound support consist only Headset output on the board and can be
handled by "simple-audio-card"
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

When McASP is not in use the pins can be put to sleep mode to conserve
power.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The section had two tabs instead of one.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The board uses McASP1 <-> tlv320aic3106 for analog audio and has
Headphone out and Line in connectors.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add node for McASP1 along with the needed pinctrl entries.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Analog audio is using this codec on the board.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The same regulator is used by other chips on the board. The power path is:
VBAT -> TPS63031 - Enable signal is V1_8D regulator -> V3_3D.
V3_3D is used by SD slot and tlv320aic3106 codec as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

GPIO5_8 is used as a mux switch between LCD and HDMI displays. This mux
affects audio routing as well since in LCD mode HDMI audio is not possible
and when HDMI is selected analog audio is not working.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use simple card for audio support on ePOS-EVM.
The audio on the board is: McASP1 <-> tlv320aic3111 codec.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Analog audio is using this codec on the board.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add node for McASP1 along with the needed pinctrl entries.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The VBAT and DCDC4 regulator is needed for audio support (tlv320aic3111)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

GPIO2_1 is used as a mux switch between LCD and HDMI displays. This mux
affects audio routing as well since in LCD mode HDMI audio is not possible
and when HDMI is selected analog audio is not working.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The sound support consist only Headset output on the board and can be
handled by "simple-audio-card".
Also enable the Line-In route as the board has support for it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

When McASP is not in use the pins can be put to sleep mode to conserve
power.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>