- 30 Mar, 2016 40 commits
-
-
Thomas Gleixner authored
commit e9532e69 upstream. On CPU hotplug the steal time accounting can keep a stale rq->prev_steal_time value over CPU down and up. So after the CPU comes up again the delta calculation in steal_account_process_tick() wreckages itself due to the unsigned math: u64 steal = paravirt_steal_clock(smp_processor_id()); steal -= this_rq()->prev_steal_time; So if steal is smaller than rq->prev_steal_time we end up with an insane large value which then gets added to rq->prev_steal_time, resulting in a permanent wreckage of the accounting. As a consequence the per CPU stats in /proc/stat become stale. Nice trick to tell the world how idle the system is (100%) while the CPU is 100% busy running tasks. Though we prefer realistic numbers. None of the accounting values which use a previous value to account for fractions is reset at CPU hotplug time. update_rq_clock_task() has a sanity check for prev_irq_time and prev_steal_time_rq, but that sanity check solely deals with clock warps and limits the /proc/stat visible wreckage. The prev_time values are still wrong. Solution is simple: Reset rq->prev_*_time when the CPU is plugged in again. Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Acked-by:
Rik van Riel <riel@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Glauber Costa <glommer@parallels.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Fixes: commit 095c0aa8 "sched: adjust scheduler cpu power for stolen time" Fixes: commit aa483808 "sched: Remove irq time from available CPU power" Fixes: commit e6e6685a "KVM guest: Steal time accounting" Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1603041539490.3686@nanosSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Radim Krčmář authored
commit 7dd0fdff upstream. Discard policy uses ack_notifiers to prevent injection of PIT interrupts before EOI from the last one. This patch changes the policy to always try to deliver the interrupt, which makes a difference when its vector is in ISR. Old implementation would drop the interrupt, but proposed one injects to IRR, like real hardware would. The old policy breaks legacy NMI watchdogs, where PIT is used through virtual wire (LVT0): PIT never sends an interrupt before receiving EOI, thus a guest deadlock with disabled interrupts will stop NMIs. Note that NMI doesn't do EOI, so PIT also had to send a normal interrupt through IOAPIC. (KVM's PIT is deeply rotten and luckily not used much in modern systems.) Even though there is a chance of regressions, I think we can fix the LVT0 NMI bug without introducing a new tick policy. Reported-by:
Yuki Shibuya <shibuya.yk@ncos.nec.co.jp> Reviewed-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Oliver Neukum authored
commit 0d5ce778 upstream. A typo of j for i led to a logic bug. To rule out future confusion, the variable names are made meaningful. Signed-off-by:
Oliver Neukum <ONeukum@suse.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Vinayak Menon authored
commit e53b50c0 upstream. early_init_dt_alloc_reserved_memory_arch passes end as 0 to __memblock_alloc_base, when limits are not specified. But __memblock_alloc_base takes end value of 0 as MEMBLOCK_ALLOC_ACCESSIBLE and limits the end to memblock.current_limit. This results in regions never being placed in HIGHMEM area, for e.g. CMA. Let __memblock_alloc_base allocate from anywhere in memory if limits are not specified. Acked-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Vinayak Menon <vinmenon@codeaurora.org> Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Asai Thambi SP authored
commit aae4a033 upstream. Allow device initialization to finish gracefully when it is in FTL rebuild failure state. Also, recover device out of this state after successfully secure erasing it. Signed-off-by:
Selvan Mani <smani@micron.com> Signed-off-by:
Vignesh Gunasekaran <vgunasekaran@micron.com> Signed-off-by:
Asai Thambi S P <asamymuthupa@micron.com> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Asai Thambi SP authored
commit 51c6570e upstream. Flush inflight IOs using fsync_bdev() when the device is safely removed. Also, block further IOs in device open function. Signed-off-by:
Rajesh Kumar Sambandam <rsambandam@micron.com> Signed-off-by:
-
Asai Thambi SP authored
commit 59cf70e2 upstream. When FTL rebuild is in progress, alloc_disk() initializes the disk but device node will be created by add_disk() only after successful completion of FTL rebuild. So, skip deletion of device node in removal path when FTL rebuild is in progress. Signed-off-by:
-
Asai Thambi SP authored
commit d8a18d2d upstream. Prevent standby immediate command from being issued in remove, suspend and shutdown paths, while drive is in FTL rebuild process. Signed-off-by:
-
Asai Thambi SP authored
commit 5b7e0a8a upstream. Print exact time when an internal command is interrupted. Signed-off-by:
-
Asai Thambi SP authored
commit e35b9473 upstream. Remove setting and clearing MTIP_PF_EH_ACTIVE_BIT flag in mtip_handle_tfe() as they are redundant. Also avoid waking up service thread from mtip_handle_tfe() because it is already woken up in case of taskfile error. Signed-off-by:
-
Asai Thambi SP authored
commit cfc05bd3 upstream. Service thread does not detect the need for taskfile error hanlding. Fixed the flag condition to process taskfile error. Signed-off-by:
-
Nikolay Borisov authored
commit ab73ef46 upstream. When dqget() in __dquot_initialize() fails e.g. due to IO error, __dquot_initialize() will pass an array of uninitialized pointers to dqput_all() and thus can lead to deference of random data. Fix the problem by properly initializing the array. Signed-off-by:
Nikolay Borisov <kernel@kyup.com> Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Mateusz Guzik authored
commit 2e83b79b upstream. This plugs 2 trivial leaks in xfs_attr_shortform_list and xfs_attr3_leaf_list_int. Signed-off-by:
Mateusz Guzik <mguzik@redhat.com> Reviewed-by:
Eric Sandeen <sandeen@redhat.com> Signed-off-by:
Dave Chinner <david@fromorbit.com> Signed-off-by:
-
J. Bruce Fields authored
commit 4aed9c46 upstream. A number of spots in the xdr decoding follow a pattern like n = be32_to_cpup(p++); READ_BUF(n + 4); where n is a u32. The only bounds checking is done in READ_BUF itself, but since it's checking (n + 4), it won't catch cases where n is very large, (u32)(-4) or higher. I'm not sure exactly what the consequences are, but we've seen crashes soon after. Instead, just break these up into two READ_BUF()s. Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Michael S. Tsirkin authored
commit 10e7ac22 upstream. Calling return copy_to_user(...) in an ioctl will not do the right thing if there's a pagefault: copy_to_user returns the number of bytes not copied in this case. Fix up watchdog/rc32434_wdt to do return copy_to_user(...)) ? -EFAULT : 0; instead. Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
Wim Van Sebroeck <wim@iguana.be> Signed-off-by:
-
Hans de Goede authored
commit 5c915c68 upstream. On my bttv card "Hauppauge WinTV [card=10]" capturing in YV12 fmt at max size results in a solid green rectangle being captured (all colors 0 in YUV). This turns out to be caused by max-width (924) not being a multiple of 16. We've likely never hit this problem before since normally xawtv / tvtime, etc. will prefer packed pixel formats. But when using a video card which is using xf86-video-modesetting + glamor, only planar XVideo fmts are available, and xawtv will chose a matching capture format to avoid needing to do conversion, triggering the solid green window problem. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Acked-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Bart Van Assche authored
commit 51093254 upstream. Let the target core check task existence instead of the SRP target driver. Additionally, let the target core check the validity of the task management request instead of the ib_srpt driver. This patch fixes the following kernel crash: BUG: unable to handle kernel NULL pointer dereference at 0000000000000001 IP: [<ffffffffa0565f37>] srpt_handle_new_iu+0x6d7/0x790 [ib_srpt] Oops: 0002 [#1] SMP Call Trace: [<ffffffffa05660ce>] srpt_process_completion+0xde/0x570 [ib_srpt] [<ffffffffa056669f>] srpt_compl_thread+0x13f/0x160 [ib_srpt] [<ffffffff8109726f>] kthread+0xcf/0xe0 [<ffffffff81613cfc>] ret_from_fork+0x7c/0xb0 Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Fixes: 3e4f5748 ("ib_srpt: Convert TMR path to target_submit_tmr") Tested-by:
Alex Estrin <alex.estrin@intel.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Cc: Nicholas Bellinger <nab@linux-iscsi.org> Cc: Sagi Grimberg <sagig@mellanox.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Jiri Olsa authored
commit 67d52689 upstream. The util/python-ext-sources file contains source files required to build the python extension relative to $(srctree)/tools/perf, Such a file path $(FILE).c is handed over to the python extension build system, which builds the final object in the $(PYTHON_EXTBUILD)/tmp/$(FILE).o path. After the build is done all files from $(PYTHON_EXTBUILD)lib/ are carried as the result binaries. Above system fails when we add source file relative to ../lib, which we do for: ../lib/bitmap.c ../lib/find_bit.c ../lib/hweight.c ../lib/rbtree.c All above objects will be built like: $(PYTHON_EXTBUILD)/tmp/../lib/bitmap.c $(PYTHON_EXTBUILD)/tmp/../lib/find_bit.c $(PYTHON_EXTBUILD)/tmp/../lib/hweight.c $(PYTHON_EXTBUILD)/tmp/../lib/rbtree.c which accidentally happens to be final library path: $(PYTHON_EXTBUILD)/lib/ Changing setup.py to pass full paths of source files to Extension build class and thus keep all built objects under $(PYTHON_EXTBUILD)tmp directory. Reported-by:
Jeff Bastian <jbastian@redhat.com> Signed-off-by:
Jiri Olsa <jolsa@kernel.org> Tested-by:
Josh Boyer <jwboyer@fedoraproject.org> Cc: David Ahern <dsahern@gmail.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/20160227201350.GB28494@krava.redhat.comSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Russell King authored
commit 7f05538a upstream. The calculation for the timeout based on the number of card clocks is incorrect. The calculation assumed: timeout in microseconds = clock cycles / clock in Hz which is clearly a several orders of magnitude wrong. Fix this by multiplying the clock cycles by 1000000 prior to dividing by the Hz based clock. Also, as per part 1, ensure that the division rounds up. As this needs 64-bit math via do_div(), avoid it if the clock cycles is zero. Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Tested-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Russell King authored
commit fafcfda9 upstream. The data timeout gives the minimum amount of time that should be waited before timing out if no data is received from the card. Simply dividing the nanosecond part by 1000 does not give this required guarantee, since such a division rounds down. Use DIV_ROUND_UP() to give the desired timeout. Signed-off-by:
-
Dmitry Tunin authored
commit 81d90442 upstream. T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=03 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=3014 Rev=00.02 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb BugLink: https://bugs.launchpad.net/bugs/1546694Signed-off-by:
Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Tom Lendacky authored
commit ce0ae266 upstream. Since a crypto_ahash_import() can be called against a request context that has not had a crypto_ahash_init() performed, the request context needs to be cleared to insure there is no random data present. If not, the random data can result in a kernel oops during crypto_ahash_update(). Signed-off-by:
Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Shaohua Li authored
commit 6ab2a4b8 upstream. Revert commit e9e4c377(md/raid5: per hash value and exclusive wait_for_stripe) The problem is raid5_get_active_stripe waits on conf->wait_for_stripe[hash]. Assume hash is 0. My test release stripes in this order: - release all stripes with hash 0 - raid5_get_active_stripe still sleeps since active_stripes > max_nr_stripes * 3 / 4 - release all stripes with hash other than 0. active_stripes becomes 0 - raid5_get_active_stripe still sleeps, since nobody wakes up wait_for_stripe[0] The system live locks. The problem is active_stripes isn't a per-hash count. Revert the patch makes the live lock go away. Cc: Yuanhan Liu <yuanhan.liu@linux.intel.com> Cc: NeilBrown <neilb@suse.de> Signed-off-by:
Shaohua Li <shli@fb.com> Signed-off-by:
-
Shaohua Li authored
commit 27a353c0 upstream. check_reshape() is called from raid5d thread. raid5d thread shouldn't call mddev_suspend(), because mddev_suspend() waits for all IO finish but IO is handled in raid5d thread, we could easily deadlock here. This issue is introduced by 738a2738 ("md/raid5: fix allocation of 'scribble' array.") Reported-and-tested-by:
Artur Paszkiewicz <artur.paszkiewicz@intel.com> Reviewed-by:
NeilBrown <neilb@suse.com> Signed-off-by:
-
Jes Sorensen authored
commit e7597e69 upstream. 'max_discard_sectors' is in sectors, while 'stripe' is in bytes. This fixes the problem where DISCARD would get disabled on some larger RAID5 configurations (6 or more drives in my testing), while it worked as expected with smaller configurations. Fixes: 620125f2 ("MD: raid5 trim support") Signed-off-by:
Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by:
-
Bjorn Helgaas authored
commit b84106b4 upstream. The PCI config header (first 64 bytes of each device's config space) is defined by the PCI spec so generic software can identify the device and manage its usage of I/O, memory, and IRQ resources. Some non-spec-compliant devices put registers other than BARs where the BARs should be. When the PCI core sizes these "BARs", the reads and writes it does may have unwanted side effects, and the "BAR" may appear to describe non-sensical address space. Add a flag bit to mark non-compliant devices so we don't touch their BARs. Turn off IO/MEM decoding to prevent the devices from consuming address space, since we can't read the BARs to find out what that address space would be. Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Tested-by:
Andi Kleen <ak@linux.intel.com> Signed-off-by:
-
Aaro Koskinen authored
commit 5e64c29e upstream. Commit 5942ddbc ("mtd: introduce mtd_block_markbad interface") incorrectly changed onenand_block_markbad() to call mtd_block_markbad instead of onenand_chip's block_markbad function. As a result the function will now recurse and deadlock. Fix by reverting the change. Fixes: 5942ddbc ("mtd: introduce mtd_block_markbad interface") Signed-off-by:
Aaro Koskinen <aaro.koskinen@iki.fi> Acked-by:
Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by:
Brian Norris <computersforpeace@gmail.com> Signed-off-by:
-
Alan authored
commit 5a51a7ab upstream. We were setting the queue depth correctly, then setting it back to two. If you hit this as a bisection point then please send me an email as it would imply we've been hiding other bugs with this one. Signed-off-by:
Alan Cox <alan@linux.intel.com> Reviewed-by:
Hannes Reinicke <hare@suse.de> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Raghava Aditya Renukunta authored
commit f88fa79a upstream. aac_fib_map_free() calls pci_free_consistent() without checking that dev->hw_fib_va is not NULL and dev->max_fib_size is not zero.If they are indeed NULL/0, this will result in a hang as pci_free_consistent() will attempt to invalidate cache for the entire 64-bit address space (which would take a very long time). Fixed by adding a check to make sure that dev->hw_fib_va and dev->max_fib_size are not NULL and 0 respectively. Fixes: 9ad5204d - "[SCSI]aacraid: incorrect dma mapping mask during blinked recover or user initiated reset" Signed-off-by:
Raghava Aditya Renukunta <raghavaaditya.renukunta@pmcs.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by:
Tomas Henzl <thenzl@redhat.com> Signed-off-by:
-
Raghava Aditya Renukunta authored
commit 3f4ce057 upstream. The driver utilizes an array of atomic variables to keep track of IO submissions to each vector. To submit an IO multiple threads iterate through the array to find a vector which has empty slots to send an IO. The reading and updating of the variable is not atomic, causing race conditions when a thread uses a full vector to submit an IO. Fixed by mapping each FIB to a vector, the submission path then uses said vector to submit IO thereby removing the possibly of a race condition.The vector assignment is started from 1 since vector 0 is reserved for the use of AIF management FIBS.If the number of MSIx vectors is 1 (MSI or INTx mode) then all the fibs are allocated to vector 0. Fixes: 495c0217 "aacraid: MSI-x support" Signed-off-by:
-
Dmitry Tunin authored
commit 28c971d8 upstream. T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e095 Rev=00.01 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb This device requires ar3k/AthrBT_0x31010100.dfu and ar3k/ramps_0x31010100_40.dfu firmware files that are not in linux-firmware yet. BugLink: https://bugs.launchpad.net/bugs/1542944Signed-off-by:
-
Dmitry Tunin authored
commit 609574eb upstream. T: Bus=03 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3395 Rev=00.01 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb BugLink: https://bugs.launchpad.net/bugs/1542564Reported-and-tested-by:
Christopher Simerly <kilikopela29@gmail.com> Signed-off-by:
-
Andi Kleen authored
commit 940db6dc upstream. When an error happens during alias parsing currently the complete parsing of all attributes of the PMU is stopped. This is breaks old perf on a newer kernel that may have not-yet-know alias attributes (such as .scale or .per-pkg). Continue when some attribute is unparseable. This is IMHO a stable candidate and should be backported to older versions to avoid problems with newer kernels. v2: Print warnings when something goes wrong. v3: Change warning to debug output Signed-off-by:
-
Jarkko Sakkinen authored
commit 99cda8cb upstream. Wrong call order. Reported-by:
Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Fixes: 74d6b3ceSigned-off-by:
Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by:
-
Hans de Goede authored
commit 3e71da19 upstream. bytesperline should be the bytesperline for the first plane for planar formats, not that of all planes combined. This fixes a crash in xawtv caused by the wrong bpl. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1305389Reported-and-tested-by:
Stas Sergeev <stsp@list.ru> Signed-off-by:
-
Hans Verkuil authored
commit b339a72e upstream. The V4L2_CID_TX_EDID_PRESENT control reports if an EDID is present. The adv7511 however still reported the EDID present after disconnecting the HDMI cable. Fix the logic regarding this control. And when the EDID is disconnected also call ADV7511_EDID_DETECT to notify the bridge driver. This was also missing. Signed-off-by:
-
Julia Lawall authored
commit 1b669e71 upstream. & is no longer allowed in column 0, since Coccinelle 1.0.4. Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Tested-by:
Nishanth Menon <nm@ti.com> Signed-off-by:
Michal Marek <mmarek@suse.com> Signed-off-by:
-
Benjamin Tissoires authored
commit 4392bf33 upstream. hid_ignore_special_drivers works fine until hid_scan_report autodetects and reassign devices (for hid-multitouch, hid-microsoft and hid-rmi). Simplify the handling of the parameter: if it is there, use hid-generic, no matter what, and if not, scan the device or rely on the hid_have_special_driver table. This was detected while trying to disable hid-multitouch on a Surface Pro cover which prevented to use the keyboard. Signed-off-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Oliver Neukum authored
commit 264904cc upstream. Some devices I got show an inability to operate right after power on if they are already connected. They are beyond recovery if the descriptors are requested multiple times. So in case of a timeout we rather bail early and reset again. But it must be done only on the first loop lest we get into a reset/time out spiral that can be overcome with a retry. This patch is a rework of a patch that fell through the cracks. http://www.spinics.net/lists/linux-usb/msg103263.htmlSigned-off-by:
-
Lior Amsalem authored
commit b3a7f31e upstream. The Armada 375 has the same SATA IP as Armada 370 and Armada XP, which requires the PHY speed to be set in the LP_PHY_CTL register for SATA hotplug to work. Therefore, this commit updates the compatible string used to describe the SATA IP in Armada 375 from marvell,orion-sata to marvell,armada-370-sata. Fixes: 4de59085 ("ARM: mvebu: add Device Tree description of the Armada 375 SoC") Signed-off-by:
Lior Amsalem <alior@marvell.com> Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
