This patch adds the support for the RSS related ethtool
function. Currently it only uses one entry in the indirection table which
allows associating an mvneta interface to a given CPU.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We enable the percpu interrupt for all the CPU and we just associate a
CPU to a few queue at the neta level. The mapping between the CPUs and
the queues is static. The queues are associated to the CPU module the
number of CPUs. However currently we only use on RX queue for a given
Ethernet port.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of using the same default queue for all the port. Move it in the
port struct. It will allow have a different default queue for each port.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This gets rid of the following compile warn:
net/mpls/mpls_iptunnel.c:40:5: warning: no previous prototype for
mpls_output [-Wmissing-prototypes]
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a warn message when clip table overflows. If clip table isn't
allocated, return from cxgb4_clip_release() to avoid panic.
Disable offload if clip isn't enabled in the hardware.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We already know "err" is zero so there is no need to check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The "err = " assignment is missing here.

Fixes: 0d65fc13 ('mlxsw: spectrum: Implement LAG port join/leave')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The handling of epib and psdata remains a bit unclear in the driver,
as we access the same fields both as CPU-endian and through DMA
from the device.

Sparse warns about this:
ti/netcp_core.c:1147:21: warning: incorrect type in assignment (different base types)
ti/netcp_core.c:1147:21:    expected unsigned int [usertype] *[assigned] epib
ti/netcp_core.c:1147:21:    got restricted __le32 *<noident>

This uses __le32 types in a few places and uses __force where the code
looks fishy. The previous patch should really have produced the correct
behavior, but this second patch is needed to shut up the warnings about
it. Ideally it would be slightly rewritten to not need those casts,
but I don't dare do that without access to the hardware for proper
testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The netcp driver produces tons of warnings when CONFIG_LPAE is enabled
on ARM:

drivers/net/ethernet/ti/netcp_core.c: In function 'netcp_tx_map_skb':
drivers/net/ethernet/ti/netcp_core.c:1084:13: warning: passing argument 1 of 'set_words' from incompatible pointer type [-Wincompatible-pointer-types]

This is the result of trying to pass a pointer to a dma_addr_t to
a function that expects a u32 pointer to copy that into a DMA descriptor.

Looking at that code in more detail to fix the warnings, I see multiple
related problems:

* The conversion functions are not endian-safe, as the DMA descriptors
  are almost certainly fixed-endian, but the CPU is not.

* On 64-bit machines, passing a pointer through a u32 variable is a
  bug, accessing an indirect pointer as a u32 pointer even more so.

* The handling of epib and psdata mixes native-endian and device-endian
  data.

In this patch, I try to sort out the types for most accesses here,
adding le32_to_cpu/cpu_to_le32 where appropriate, and passing pointers
through two 32-bit words in the descriptor padding, to make it plausible
that the driver does the right thing if compiled for big-endian or
64-bit systems.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

sock_cgroup_data is a struct containing an anonymous union.
sock_cgroup_set_prioidx() and sock_cgroup_set_classid() were
initializing a field inside the anonymous union as follows.

 struct sock_ccgroup_data skcd_buf = { .val = VAL };

While this is fine on more recent compilers, gcc-4.4.7 triggers the
following errors.

 include/linux/cgroup-defs.h: In function ‘sock_cgroup_set_prioidx’:
 include/linux/cgroup-defs.h:619: error: unknown field ‘val’ specified in initializer
 include/linux/cgroup-defs.h:619: warning: missing braces around initializer
 include/linux/cgroup-defs.h:619: warning: (near initialization for ‘skcd_buf.<anonymous>’)

This is because .val belongs to the anonymous union nested inside the
struct but the initializer is missing the nesting.  Fix it by adding
an extra pair of braces.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Alaa Hleihel <alaa@dev.mellanox.co.il>
Fixes: bd1060a1 ("sock, cgroup: add sock->sk_cgroup")
Signed-off-by: David S. Miller <davem@davemloft.net>

The cmac_ops structures are never modified, so declare them as const.

Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

These fields are updated but never read.
Remove the overhead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Under heavy TX load, bnx2x_poll() can loop forever and trigger
soft lockup bugs.

A napi poll handler must yield after one TX completion round,
risk of livelock is too high otherwise.

Bug is very easy to trigger using a debug build, and udp flood, because
of added cpu cycles in TX completion, and we do not receive enough
packets to break the loop.
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch 9497df88 ("rhashtable:
Fix reader/rehash race") added a pair of barriers.  In fact the
wmb is superfluous because every subsequent write to the old or
new hash table uses rcu_assign_pointer, which itself carriers a
full barrier prior to the assignment.

Therefore we may remove the explicit wmb.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hariprasad Shenai says:

====================
Update Kconfig and some fixes for cxgb4

This series update Kconfig to add description for Chelsio's next
generation T6 family of adapters, also fixes ethtool stats alignment
and prevents simultaneous execution of service_ofldq thread, deals with
queue wrap around and adds some fl counters for debugging purpose and
device ID for new T5 adapters.

This patch series has been created against net-next tree and includes
patches on cxgb4 driver.

We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.

Thanks

V2: Declare 'service_ofldq_running' as bool in Patch 4/7 ("cxgb4: prevent
    simultaneous execution of service_ofldq()") based on review comment
    by David Miller
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add Free List DMA Mapping Errors to SGE Queue info for
Free Lists. Add Free List "Low" counter to count the number of times we
see the number of pointers that we _think_ the hardware sees in the
Free List below the Egress Threshold.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The WR headers  may not fit within one descriptor.
So we need to deal with wrap-around here.

Based on original patch by Pranjal Joshi <pjoshi@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change mutual exclusion mechanism to prevent multiple threads of
execution from running in service_ofldq() at the same time.  The old
mechanism used an implicit guard on the down-call path and none on the
restart path and wasn't working. This checking makes the mechanism
explicit and is much easier to understand as a result.

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use helper macro ACCESS_ONCE() to load from the SGE status page
to prevent the compiler loading multiple times.

Based on original work by Mike Werner <werner@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

here is the patch raising the performance of XGE by:
1)changes the way page management method for enet momery, and
2)reduces the count of rmb, and
3)adds Memory prefetching
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In cgroup v1, dealing with cgroup membership was difficult because the
number of membership associations was unbound.  As a result, cgroup v1
grew several controllers whose primary purpose is either tagging
membership or pull in configuration knobs from other subsystems so
that cgroup membership test can be avoided.

net_cls and net_prio controllers are examples of the latter.  They
allow configuring network-specific attributes from cgroup side so that
network subsystem can avoid testing cgroup membership; unfortunately,
these are not only cumbersome but also problematic.

Both net_cls and net_prio aren't properly hierarchical.  Both inherit
configuration from the parent on creation but there's no interaction
afterwards.  An ancestor doesn't restrict the behavior in its subtree
in anyway and configuration changes aren't propagated downwards.
Especially when combined with cgroup delegation, this is problematic
because delegatees can mess up whatever network configuration
implemented at the system level.  net_prio would allow the delegatees
to set whatever priority value regardless of CAP_NET_ADMIN and net_cls
the same for classid.

While it is possible to solve these issues from controller side by
implementing hierarchical allowable ranges in both controllers, it
would involve quite a bit of complexity in the controllers and further
obfuscate network configuration as it becomes even more difficult to
tell what's actually being configured looking from the network side.
While not much can be done for v1 at this point, as membership
handling is sane on cgroup v2, it'd be better to make cgroup matching
behave like other network matches and classifiers than introducing
further complications.

In preparation, this patch updates sock->sk_cgrp_data handling so that
it points to the v2 cgroup that sock was created in until either
net_prio or net_cls is used.  Once either of the two is used,
sock->sk_cgrp_data reverts to its previous role of carrying prioidx
and classid.  This is to avoid adding yet another cgroup related field
to struct sock.

As the mode switching can happen at most once per boot, the switching
mechanism is aimed at lowering hot path overhead.  It may leak a
finite, likely small, number of cgroup refs and report spurious
prioidx or classid on switching; however, dynamic updates of prioidx
and classid have always been racy and lossy - socks between creation
and fd installation are never updated, config changes don't update
existing sockets at all, and prioidx may index with dead and recycled
cgroup IDs.  Non-critical inaccuracies from small race windows won't
make any noticeable difference.

This patch doesn't make use of the pointer yet.  The following patch
will implement netfilter match for cgroup2 membership.

v2: Use sock_cgroup_data to avoid inflating struct sock w/ another
    cgroup specific field.

v3: Add comments explaining why sock_data_prioidx() and
    sock_data_classid() use different fallback values.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Daniel Wagner <daniel.wagner@bmw-carit.de>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce sock->sk_cgrp_data which is a struct sock_cgroup_data.
->sk_cgroup_prioidx and ->sk_classid are moved into it.  The struct
and its accessors are defined in cgroup-defs.h.  This is to prepare
for overloading the fields with a cgroup pointer.

This patch mostly performs equivalent conversions but the followings
are noteworthy.

* Equality test before updating classid is removed from
  sock_update_classid().  This shouldn't make any noticeable
  difference and a similar test will be implemented on the helper side
  later.

* sock_update_netprioidx() now takes struct sock_cgroup_data and can
  be moved to netprio_cgroup.h without causing include dependency
  loop.  Moved.

* The dummy version of sock_update_netprioidx() converted to a static
  inline function while at it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

netprio builds per-netdev contiguous priomap array which is indexed by
css->id.  The array is allocated using kzalloc() effectively limiting
the maximum ID supported to some thousand range.  This patch caps the
maximum supported css->id to USHRT_MAX which should be way above what
is actually useable.

This allows reducing sock->sk_cgrp_prioidx to u16 from u32.  The freed
up part will be used to overload the cgroup related fields.
sock->sk_cgrp_prioidx's position is swapped with sk_mark so that the
two cgroup related fields are adjacent.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Preparatory changes for some new socket cgroup infrastructure
and netfilter targets.
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 0d76d6e8 and merge
commit c402293b, reversing changes made
to c89359a4.

The virtio-vsock device specification is not finalized yet.  Michael
Tsirkin voiced concerned about merging this code when the hardware
interface (and possibly the userspace interface) could still change.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sergei Shtylyov says:

====================
sh_eth: optimize MDIO code

Here's a set of 3 patches against DaveM's 'net-next.git' repo which
gets rid of ~35 LoCs in the MDIO bitbang methods.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After the MDIO bitbang code consolidation, there's no need anymore for
bb_{set|clr}() as well as bb_read() -- just expand them inline, thus
saving more LoCs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

sh_mm[cd]_ctrl()  and sh_set_mdio() all look mostly the same -- factor out
their common code and put it into sh_mdio_ctrl().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MDIO control bits are always mapped to the same bits of the same register
(PIR), so there's no need to store their masks in the 'struct bb_info'...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The xgene_mac_ops and xgene_port_ops structures are never modified, so
declare them as const.

Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2015-12-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Vallo says:

====================
brcfmac

* support bcm4359 which can operate in two bands concurrently
* disable runtime pm for USB avoiding issues
* use generic pm callback in PCIe driver
* support wowlan wake indication reporting
* add beamforming support
* unified handling of firmware files

ath10k

* support Manegement Frame Protection (MFP)
* add thermal throttling support for 10.4 firmware
* add support for pktlog in QCA99X0
* add debugfs file to enable Bluetooth coexistence feature
* use firmware's native mesh interface type instead of raw mode

iwlwifi

* BT coex improvements
* D3 operation bugfixes
* rate control improvements
* firmware debugging infra improvements
* ground work for multi Rx
* various security fixes
====================

Conflicts:
	drivers/net/wireless/ath/ath10k/pci.c

The conflict resolution at:

	http://article.gmane.org/gmane.linux.kernel.next/37391

by Stephen Rothwell was used.
Signed-off-by: David S. Miller <davem@davemloft.net>

As the kernel generally uses negated error numbers, *err needs to be
compared with -EAGAIN (d'oh).
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Fixes: ea3793ee ("core: enable more fine-grained datagram reception control")
Signed-off-by: David S. Miller <davem@davemloft.net>

the simple_strtoul function is obsolete. This patch replace it by
kstrtox.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Neil Armstrong says:

====================
Further fix for dsa unbinding

This series fixes further issues for DSA dynamic unbinding.
The first patch completely removes the PHY link state polling.
The two following cleans up the dsa state upon removal.
The last patch moves slave destroy code as slave function and
adds missing netdev and phy cleanup calls.

v1: http://lkml.kernel.org/r/562F8ECB.6050709@baylibre.com
v2: http://lkml.kernel.org/r/56321D9A.8010109@baylibre.com
remove phy fix and add missing calls in dsa_switch_destroy
then add dedicated dsa_slave_destroy

v3: remove polling instead of fixing it, make single patch for
dsa slave destroy
====================
Acked-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move dsa slave dedicated code from dsa_switch_destroy to a new
dsa_slave_destroy function in slave.c.
Add the netif_carrier_off and phy_disconnect calls in order to
correctly cleanup the netdev state and PHY state machine.
Signed-off-by: Frode Isaksen <fisaksen@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Upon probe failure or unbinding, add missing dev_put() calls.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure that we unassign the master_netdev dsa_ptr to make the packet
processing go through the regular Ethernet receive path.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>