This driver was originally written by James McKenzie, updated by
Greg Kroah-Hartman, further updated by Bastien Nocera, with suspend
support added.
I ported it to the HID subsystem, in order to simplify it a litle
and allow lirc to use it through hiddev.

More recent versions of the IR receiver are also supported through
a patch by Alex Karpenko. The patch also adds support for the 2nd
and 5th generation of the controller, and the menu key on newer
brushed metal remotes.
Tested-by: Fabien André <fabien.andre@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Pull HID fixes from Jiri Kosina:

 - Workaround for device ID conflict between Masterkit MA901 usb radio
   device and Atmel V-USB devices, to avoid regressions from older
   kernels, by Alexey Klimov

 - fix for possible race during input device registration in magicmouse
   driver, by Benjamin Tissoires

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: magicmouse: fix race between input_register() and probe()
  media: radio-ma901: return ENODEV in probe if usb_device doesn't match
  HID: fix Masterkit MA901 hid quirks

Pull GPIO fixes from Linus Walleij:
 "Two GPIO fixes for the v3.9 series:
   - Fix erroneous return value in the ICH driver
   - Make the STMPE driver proper properly on device tree boots"

* tag 'gpio-fixes-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: stmpe: pass DT node to irqdomain
  gpio-ich: Fix value returned by ichx_gpio_request

Since kernel 3.7, it appears that the input registration occured before
the end of magicmouse_setup_input(). This is shown by receiving a lot of
"EV_SYN SYN_REPORT 1" instead of normal "EV_SYN SYN_REPORT 0".
This value means that the output buffer is full, and the user space
is loosing events.

Using .input_configured guarantees that the race is not occuring, and that
the call of "input_set_events_per_packet(input, 60)" is taken into account
by input_register().

Fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=908604

Cc: stable@vger.kernel.org
Reported-and-Tested-By: Clarke Wixon <cwixon@usa.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Pull ARM fixes from Russell King:
 "Another round of ARM fixes, which include:
   - Fixing a problem with LPAE mapping sections
   - Reporting of some hwcaps on Krait CPUs
   - Avoiding repetitive warnings in the breakpoint code
   - Fixing a build error noticed on Dove platforms with PJ4 CPUs
   - Fix masking of level 2 cache revision.
   - Fixing timer-based udelay()
   - A larger fix for an erratum causing people major grief with Cortex
     A15 CPUs"

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7690/1: mm: fix CONFIG_LPAE typos
  ARM: 7689/1: add unwind annotations to ftrace asm
  ARM: 7685/1: delay: use private ticks_per_jiffy field for timer-based delay ops
  ARM: 7684/1: errata: Workaround for Cortex-A15 erratum 798181 (TLBI/DSB operations)
  ARM: 7682/1: cache-l2x0: fix masking of RTL revision numbering and set_debug init
  ARM: iWMMXt: always enable iWMMXt support with PJ4 CPUs
  ARM: 7681/1: hw_breakpoint: use warn_once to avoid spam from reset_ctrl_regs()
  ARM: 7678/1: Work around faulty ISAR0 register in some Krait CPUs
  ARM: 7680/1: Detect support for SDIV/UDIV from ISAR0 register
  ARM: 7679/1: Clear IDIVT hwcap if CONFIG_ARM_THUMB=n
  ARM: 7677/1: LPAE: Fix mapping in alloc_init_section for unaligned addresses
  ARM: KVM: vgic: take distributor lock on sync_hwstate path
  ARM: KVM: vgic: force EOIed LRs to the empty state

Pull ext4 fixes from Ted Ts'o:
 "Unfortunately, we introduced some big-endian bugs during the last
  merge window.  Fortunately, Cai and Christian noticed before 3.9
  shipped."

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix big-endian bugs which could cause fs corruptions

Pull reiserfs fix from Jan Kara:
 "A fix for reiserfs xattr bug exposed by changes to lookup_one_len()"

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  reiserfs: Fix warning and inode leak when deleting inode with xattrs

Pull s390 fixes from Martin Schwidefsky:
 "Just a bunch of bugfixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/mm: provide emtpy check_pgt_cache() function
  s390/uaccess: fix page table walk
  s390/3270: fix minor_start issue
  s390/uaccess: fix clear_user_pt()
  s390/scm_blk: fix error return code in scm_blk_init()
  s390/scm_block: fix printk format string
  drivers/Kconfig: add several missing GENERIC_HARDIRQS dependencies

When an extent was zeroed out, we forgot to do convert from cpu to le16.
It could make us hit a BUG_ON when we try to write dirty pages out.  So
fix it.

[ Also fix a bug found by Dmitry Monakhov where we were missing
  le32_to_cpu() calls in the new indirect punch hole code.

  There are a number of other big endian warnings found by static code
  analyzers, but we'll wait for the next merge window to fix them all
  up.  These fixes are designed to be Obviously Correct by code
  inspection, and easy to demonstrate that it won't make any
  difference (and hence, won't introduce any bugs) on little endian
  architectures such as x86.  --tytso ]
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reported-by: CAI Qian <caiqian@redhat.com>
Reported-by: Christian Kujau <lists@nerdbynature.de>
Cc: Dmitry Monakhov <dmonakhov@openvz.org>

CONFIG_LPAE doesn't exist: the correct option is CONFIG_ARM_LPAE, so fix
up the two typos under arch/arm/.

The fix to head.S is slightly scary, but this is just for setting up
an early io-mapping for the serial port when running on a big-endian,
LPAE system. Since these systems don't exist in the wild (at least, I
have no access to one outside of kvmtool, which doesn't provide a serial
port suitable for earlyprintk), then we can revisit the code later if it
causes any problems.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add unwind annotations to the ftrace assembly code so that the function
tracer's stacktracing options (func_stack_trace, etc.) work when
CONFIG_ARM_UNWIND is enabled.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Commit 70264367 ("ARM: 7653/2: do not scale loops_per_jiffy when
using a constant delay clock") fixed a problem with our timer-based
delay loop, where loops_per_jiffy is scaled by cpufreq yet used directly
by the timer delay ops.

This patch fixes the problem in a more elegant way by keeping a private
ticks_per_jiffy field in the delay ops, independent of loops_per_jiffy
and therefore not subject to scaling. The loop-based delay continues to
use loops_per_jiffy directly, as it should.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

On Cortex-A15 (r0p0..r3p2) the TLBI/DSB are not adequately shooting down
all use of the old entries. This patch implements the erratum workaround
which consists of:

1. Dummy TLBIMVAIS and DSB on the CPU doing the TLBI operation.
2. Send IPI to the CPUs that are running the same mm (and ASID) as the
   one being invalidated (or all the online CPUs for global pages).
3. CPU receiving the IPI executes a DMB and CLREX (part of the exception
   return code already).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Commit b8db6b88 (ARM: 7547/4: cache-l2x0: add support for Aurora L2 cache
ctrl) moved the masking of the part ID which caused the RTL version to be
lost. Commit 6248d060 (ARM: 7545/1: cache-l2x0: make outer_cache_fns a
field of l2x0_of_data) changed how .set_debug is initialized. Both commits
break commit 74ddcdb8 (ARM: 7608/1: l2x0: Only set .set_debug
on PL310 r3p0 and earlier) which uses the RTL version to conditionally set
.set_debug function pointer. Commit b8db6b88 also caused the printed cache
ID to be missing the version information.

Fix this by reverting how the part number is masked so the RTL version
info is maintained. The cache-id-part DT property does not set the RTL
bits so masking them should have no effect. Also, re-arrange the order
of the function pointer init so the .set_debug function can be overridden.
Reported-by: Paolo Pisati <paolo.pisati@canonical.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Jason Cooper reports these build errors:
arch/arm/kernel/built-in.o: In function `iwmmxt_do':
/.../arch/arm/kernel/pj4-cp0.c:36: undefined reference to `iwmmxt_task_release'
/.../arch/arm/kernel/pj4-cp0.c:40: undefined reference to `iwmmxt_task_switch'
make: *** [vmlinux] Error 1

This is caused because the PJ4 code explicitly references the iWMMXt
code, but doesn't require it to be built.  Fix this by ensuring that
iWMMXt is always enabled with PJ4.
Reported-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Pull networking fixes from David Miller:

 1) Fix VSOCK layer handling of context ID changes, from Reilly Grant.

 2) Now that we have a synchronize_net() in netdev_rx_handler_unregister(),
    we can't let any call sites hold locks.  Unfortunately bonding does,
    so we have to drop the rwlock there a little bit earlier, fix from
    Veaceslav Falico.

 3) MAC address setting loop exits one iteration too early in mlx4
    driver, from Yan Burman.

 4) Restore ipv6 routes properly upon ifdown/ifup of loopback, from
    Balakumaran Kannan.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  VSOCK: Handle changes to the VMCI context ID.
  net IPv6 : Fix broken IPv6 routing table after loopback down-up
  cbq: incorrect processing of high limits
  net/mlx4_en: Fix setting initial MAC address
  bonding: get netdev_rx_handler_unregister out of locks

Pull regmap fixes from Mark Brown:
 "A small collection of fixes.  The most important ones are those from
  Stephen and Lars-Peter both of which fix cache issues that have been
  lurking for a while but not manifesting noticably enough for anyone to
  report them."

* tag 'regmap-v3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: async: Add missing return
  regmap: don't corrupt work buffer in _regmap_raw_write()
  regmap: cache Fix regcache-rbtree sync
  regmap: Initialize `map->debugfs' before regcache

Pull DRM fixes from Dave Airlie:
 "Two core fixes, both regressions, along with some intel and some
  nouveau fixes for regressions and oopses"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm: correctly restore mappings if drm_open fails
  drm/nouveau: fix NULL ptr dereference from nv50_disp_intr()
  drm/nouveau: fix handling empty channel list in ioctl's
  drm: don't unlock in the addfb error paths
  drm/i915: Fix build failure
  drm/i915: Be sure to turn hsync/vsync back on at crt enable (v2)
  drm/i915: duct-tape locking when eDP init fails

Pull MIPS fixes from Ralf Baechle:
 "A collection of fixes pretty much across the MIPS code.  Even the
  change to include/linux/signal.h by David Howells' 2a148698 ("Fix
  breakage in MIPS siginfo handling") should be considered MIPS-specific
  as it touches an ifdefed segment that is only relevant to MIPS and
  which unfortunately can't be made to go away entirely."

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  Fix breakage in MIPS siginfo handling
  Revert "MIPS: BCM63XX: Call board_register_device from device_initcall()"
  MIPS: BCM63XX: Make nvram checksum failure non fatal
  MIPS: Fix code generation for non-DSP capable CPUs
  MIPS: Fix inconsistent formatting inside /proc/cpuinfo
  MIPS: SEAD3: Enable LL/SC.
  MIPS: Get rid of CONFIG_CPU_HAS_LLSC again
  MIPS: Add dependencies for HAVE_ARCH_TRANSPARENT_HUGEPAGE
  MIPS: VR4133: Fix probe for LL/SC.
  MIPS: Fix logic errors in bitops.c
  MIPS: Use CONFIG_CPU_MIPSR2 in csum_partial.S
  MIPS: compat: Return same error ENOSYS as native for invalid operation.

If first drm_open fails, the error-handling path will
incorrectly restore inode's mapping to NULL. This can
cause the crash later on. Fix by separately storing
away mapping pointers that drm_open can touch and
restore each from its own respective variable if the
call fails.

Fixes: https://bugzilla.novell.com/show_bug.cgi?id=807850
(thanks to Michal Hocko for investigating investigating and
finding the root cause of the bug)

Reference:
http://lists.freedesktop.org/archives/dri-devel/2013-March/036564.html

v2: Use one variable to store file and inode mapping
    since they are the same at the function entry.
    Fix spelling mistakes in commit message.

v3: Add reference to the original bug report.
Reported-by: Marco Munderloh <munderl@tnt.uni-hannover.de>
Tested-by: Marco Munderloh <munderl@tnt.uni-hannover.de>
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

Merge branch 'drm-nouveau-fixes-3.9' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-next

Oops fixers.
* 'drm-nouveau-fixes-3.9' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
  drm/nouveau: fix NULL ptr dereference from nv50_disp_intr()
  drm/nouveau: fix handling empty channel list in ioctl's

One locking regression fix, and a couple of other i915 ones.

* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
  drm: don't unlock in the addfb error paths
  drm/i915: Fix build failure
  drm/i915: Be sure to turn hsync/vsync back on at crt enable (v2)
  drm/i915: duct-tape locking when eDP init fails

The VMCI context ID of a virtual machine may change at any time. There
is a VMCI event which signals this but datagrams may be processed before
this is handled. It is therefore necessary to be flexible about the
destination context ID of any datagrams received. (It can be assumed to
be correct because it is provided by the hypervisor.) The context ID on
existing sockets should be updated to reflect how the hypervisor is
currently referring to the system.
Signed-off-by: Reilly Grant <grantr@vmware.com>
Acked-by: Andy King <acking@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPv6 Routing table becomes broken once we do ifdown, ifup of the loopback(lo)
interface. After down-up, routes of other interface's IPv6 addresses through
'lo' are lost.

IPv6 addresses assigned to all interfaces are routed through 'lo' for internal
communication. Once 'lo' is down, those routing entries are removed from routing
table. But those removed entries are not being re-created properly when 'lo' is
brought up. So IPv6 addresses of other interfaces becomes unreachable from the
same machine. Also this breaks communication with other machines because of
NDISC packet processing failure.

This patch fixes this issue by reading all interface's IPv6 addresses and adding
them to IPv6 routing table while bringing up 'lo'.

==Testing==
Before applying the patch:
$ route -A inet6
Kernel IPv6 routing table
Destination                    Next Hop                   Flag Met Ref Use If
2000::20/128                   ::                         U    256 0     0 eth0
fe80::/64                      ::                         U    256 0     0 eth0
::/0                           ::                         !n   -1  1     1 lo
::1/128                        ::                         Un   0   1     0 lo
2000::20/128                   ::                         Un   0   1     0 lo
fe80::xxxx:xxxx:xxxx:xxxx/128  ::                         Un   0   1     0 lo
ff00::/8                       ::                         U    256 0     0 eth0
::/0                           ::                         !n   -1  1     1 lo
$ sudo ifdown lo
$ sudo ifup lo
$ route -A inet6
Kernel IPv6 routing table
Destination                    Next Hop                   Flag Met Ref Use If
2000::20/128                   ::                         U    256 0     0 eth0
fe80::/64                      ::                         U    256 0     0 eth0
::/0                           ::                         !n   -1  1     1 lo
::1/128                        ::                         Un   0   1     0 lo
ff00::/8                       ::                         U    256 0     0 eth0
::/0                           ::                         !n   -1  1     1 lo
$

After applying the patch:
$ route -A inet6
Kernel IPv6 routing
table
Destination                    Next Hop                   Flag Met Ref Use If
2000::20/128                   ::                         U    256 0     0 eth0
fe80::/64                      ::                         U    256 0     0 eth0
::/0                           ::                         !n   -1  1     1 lo
::1/128                        ::                         Un   0   1     0 lo
2000::20/128                   ::                         Un   0   1     0 lo
fe80::xxxx:xxxx:xxxx:xxxx/128  ::                         Un   0   1     0 lo
ff00::/8                       ::                         U    256 0     0 eth0
::/0                           ::                         !n   -1  1     1 lo
$ sudo ifdown lo
$ sudo ifup lo
$ route -A inet6
Kernel IPv6 routing table
Destination                    Next Hop                   Flag Met Ref Use If
2000::20/128                   ::                         U    256 0     0 eth0
fe80::/64                      ::                         U    256 0     0 eth0
::/0                           ::                         !n   -1  1     1 lo
::1/128                        ::                         Un   0   1     0 lo
2000::20/128                   ::                         Un   0   1     0 lo
fe80::xxxx:xxxx:xxxx:xxxx/128  ::                         Un   0   1     0 lo
ff00::/8                       ::                         U    256 0     0 eth0
::/0                           ::                         !n   -1  1     1 lo
$
Signed-off-by: Balakumaran Kannan <Balakumaran.Kannan@ap.sony.com>
Signed-off-by: Maruthi Thotad <Maruthi.Thotad@ap.sony.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

currently cbq works incorrectly for limits > 10% real link bandwidth,
and practically does not work for limits > 50% real link bandwidth.
Below are results of experiments taken on 1 Gbit link

 In shaper | Actual Result
-----------+---------------
  100M     | 108 Mbps
  200M     | 244 Mbps
  300M     | 412 Mbps
  500M     | 893 Mbps

This happen because of q->now changes incorrectly in cbq_dequeue():
when it is called before real end of packet transmitting,
L2T is greater than real time delay, q_now gets an extra boost
but never compensate it.

To fix this problem we prevent change of q->now until its synchronization
with real time.
Signed-off-by: Vasily Averin <vvs@openvz.org>
Reviewed-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure that msg pointer is set back to error value in case of
MSG_COPY flag is set and desired message to copy wasn't found.  This
garantees that msg is either a error pointer or a copy address.

Otherwise the last message in queue will be freed without unlinking from
the queue (which leads to memory corruption) and the dummy allocated
copy won't be released.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 6bbb6d99 "net/mlx4_en: Optimize Rx fast path filter checks" introduced a regression
under which the MAC address read from the card was not converted correctly
(the most significant byte was not handled), fix that.
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that netdev_rx_handler_unregister contains synchronize_net(), we need
to call it outside of bond->lock, cause it might sleep. Also, remove the
already unneded synchronize_net().
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull ARM SoC bug fixes from Arnd Bergmann:
 "After a quiet set of fixes for 3.9-rc4, a lot of people woke up and
  sent urgent fixes for 3.9.  I pushed back on a number of them that got
  deferred to 3.10, but these are the ones that seemed important.

  Regression in 3.9:

   - Multiple regressions in OMAP2+ clock cleanup
   - SH-Mobile frame buffer bug fix that merged here because of
     maintainer MIA
   - ux500 prcmu changes broke DT booting
   - MMCI duplicated regulator setup on ux500
   - New ux500 clock driver broke ethernet on snowball
   - Local interrupt driver for mvebu broke ethernet
   - MVEBU GPIO driver did not get set up right on Orion DT
   - incorrect interrupt number on Orion crypto for DT

  Long-standing bugs, including candidates for stable:

   - Kirkwood MMC needs to disable invalid card detect pins
   - MV SDIO pinmux was wrong on Mirabox
   - GoFlex Net board file needs to set NAND chip delay
   - MSM timer restart race
   - ep93xx early debug code broke in 3.7
   - i.MX CPU hotplug race
   - Incorrect clock setup for OMAP1 USB
   - Workaround for bad clock setup by some old OMAP4 boot loaders
   - Static I/O mappings on cns3xxx since 3.2"

* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: cns3xxx: fix mapping of private memory region
  arm: mvebu: Fix pinctrl for Armada 370 Mirabox SDIO port.
  arm: orion5x: correct IRQ used in dtsi for mv_cesa
  arm: orion5x: fix orion5x.dtsi gpio parameters
  ARM: Kirkwood: fix unused mvsdio gpio pins
  arm: mvebu: Use local interrupt only for the timer 0
  ARM: kirkwood: Fix chip-delay for GoFlex Net
  ARM: ux500: Enable the clock controlling Ethernet on Snowball
  ARM: ux500: Stop passing ios_handler() as an MMCI power controlling call-back
  ARM: ux500: Apply the TCPM and TCDM locations and sizes to dbx5x0 DT
  fbdev: sh_mobile_lcdc: fixup B side hsync adjust settings
  ARM: OMAP: clocks: Delay clk inits atleast until slab is initialized
  ARM: imx: fix sync issue between imx_cpu_die and imx_cpu_kill
  ARM: msm: Stop counting before reprogramming clockevent
  ARM: ep93xx: Fix wait for UART FIFO to be empty
  ARM: OMAP4: PM: fix PM regression introduced by recent clock cleanup
  ARM: OMAP3: hwmod data: keep MIDLEMODE in force-standby for musb
  ARM: OMAP4: clock data: lock USB DPLL on boot
  ARM: OMAP1: fix USB host on 1710

Pull nfsd bugfix from J Bruce Fields:
 "An xdr decoding error--thanks, Toralf Förster, and Trinity!"

* 'for-3.9' of git://linux-nfs.org/~bfields/linux:
  nfsd4: reject "negative" acl lengths

From Anton Vorontsov <anton@enomsg.org>:

This tag includes Mac Lin's work to revive CNS3xxx booting:

 "Since commit 0536bdf3 (ARM: move iotable mappings within the vmalloc
 region), [...] the pre-defined iotable mappings is not in the vmalloc
 region. [...] move the iotable mappings into the vmalloc region, and
 merge the MPCore private memory region (containing the SCU, the GIC and
 the TWD) as a single region."

Plus there is a small cosmetic fix, also from Mac Lin.

* tag 'v3.9-rc1_cns3xxx_fixes' of git://git.infradead.org/users/cbou/linux-cns3xxx:
  ARM: cns3xxx: fix mapping of private memory region

[arnd: dropped the cosmetic fix from the merge as it is not needed for 3.9]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

All architectures need to provide a check_pgt_cache() function. The s390 one
got lost somewhere.
So reintroduce it to prevent future compile errors e.g. if Thomas Gleixner's
idle loop rework patches get merged.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

When translating user space addresses to kernel addresses the follow_table()
function had two bugs:

- PROT_NONE mappings could be read accessed via the kernel mapping. That is
  e.g. putting a filename into a user page, then protecting the page with
  PROT_NONE and afterwards issuing the "open" syscall with a pointer to
  the filename would incorrectly succeed.

- when walking the page tables it used the pgd/pud/pmd/pte primitives which
  with dynamic page tables give no indication which real level of page tables
  is being walked (region2, region3, segment or page table). So in case of an
  exception the translation exception code passed to __handle_fault() is not
  necessarily correct.
  This is not really an issue since __handle_fault() doesn't evaluate the code.
  Only in case of e.g. a SIGBUS this code gets passed to user space. If user
  space can do something sane with the value is a different question though.

To fix these issues don't use any Linux primitives. Only walk the page tables
like the hardware would do it, however we leave quite some checks away since
we know that we only have full size page tables and each index is within bounds.

In theory this should fix all issues...
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Pull virtio fixes from Rusty Russell:
 "One reversion, a tiny leak fix, and a cc:stable locking fix, in two
  parts"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
  virtio: console: add locking around c_ovq operations
  virtio: console: rename cvq_lock to c_ivq_lock
  hw_random: free rng_buffer at module exit
  Revert "virtio_console: Initialize guest_connected=true for rproc_serial"

struct block_device lifecycle is defined by its inode (see fs/block_dev.c) -
block_device allocated first time we access /dev/loopXX and deallocated on
bdev_destroy_inode. When we create the device "losetup /dev/loopXX afile"
we want that block_device stay alive until we destroy the loop device
with "losetup -d".

But because we do not hold /dev/loopXX inode its counter goes 0, and
inode/bdev can be destroyed at any moment. Usually it happens at memory
pressure or when user drops inode cache (like in the test below). When later in
loop_clr_fd() we want to use bdev we have use-after-free error with following
stack:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000280
  bd_set_size+0x10/0xa0
  loop_clr_fd+0x1f8/0x420 [loop]
  lo_ioctl+0x200/0x7e0 [loop]
  lo_compat_ioctl+0x47/0xe0 [loop]
  compat_blkdev_ioctl+0x341/0x1290
  do_filp_open+0x42/0xa0
  compat_sys_ioctl+0xc1/0xf20
  do_sys_open+0x16e/0x1d0
  sysenter_dispatch+0x7/0x1a

To prevent use-after-free we need to grab the device in loop_set_fd()
and put it later in loop_clr_fd().

The issue is reprodusible on current Linus head and v3.3. Here is the test:

  dd if=/dev/zero of=loop.file bs=1M count=1
  while [ true ]; do
    losetup /dev/loop0 loop.file
    echo 2 > /proc/sys/vm/drop_caches
    losetup -d /dev/loop0
  done

[ Doing bdgrab/bput in loop_set_fd/loop_clr_fd is safe, because every
  time we call loop_set_fd() we check that loop_device->lo_state is
  Lo_unbound and set it to Lo_bound If somebody will try to set_fd again
  it will get EBUSY.  And if we try to loop_clr_fd() on unbound loop
  device we'll get ENXIO.

  loop_set_fd/loop_clr_fd (and any other loop ioctl) is called under
  loop_device->lo_ctl_mutex. ]
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull tegra clock driver fix from Mike Turquette:
 "Missing base address in Tegra clock driver results in non-operational
  PCIe.  On some devices this means that Ethernet will go uninitialized
  and other devices will fail.  This pull request fixes it with a single
  patch to pass the proper base address in the Tegra clock driver."

* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
  clk: tegra: Allow PLLE training to succeed

Pull FCoE fixes from Robert Love:
 "Critical patches to fix FCoE VN2VN mode with new interfaces targeting
  3.9-rc"

* tag 'for-3.9-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rwlove/fcoe:
  libfcoe: Fix fcoe_sysfs VN2VN mode
  libfc, fcoe, bnx2fc: Split fc_disc_init into fc_disc_{init, config}
  libfc, fcoe, bnx2fc: Always use fcoe_disc_init for discovery layer initialization
  fcoe: Fix deadlock between create and destroy paths
  bnx2fc: Make the fcoe_cltr the SCSI host parent

Under some circumstances the PLLE needs to be retrained, in which case
access to the PMC registers is required. Fix this by passing a pointer
to the PMC registers instead of NULL when registering the PLLE clock.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>

Pull arch/tile fix from Chris Metcalf:
 "This change allows newer Tilera boot tools to work correctly with
  current (and stable) kernels by using the right filename to get the
  initramfs from the Tilera hypervisor filesystem."

* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  tile: expect new initramfs name from hypervisor file system

Pull networking fixes from David Miller:

 1) sadb_msg prepared for IPSEC userspace forgets to initialize the
    satype field, fix from Nicolas Dichtel.

 2) Fix mac80211 synchronization during station removal, from Johannes
    Berg.

 3) Fix IPSEC sequence number notifications when they wrap, from Steffen
    Klassert.

 4) Fix cfg80211 wdev tracing crashes when add_virtual_intf() returns an
    error pointer, from Johannes Berg.

 5) In mac80211, don't call into the channel context code with the
    interface list mutex held.  From Johannes Berg.

 6) In mac80211, if we don't actually associate, do not restart the STA
    timer, otherwise we can crash.  From Ben Greear.

 7) Missing dma_mapping_error() check in e1000, ixgb, and e1000e.  From
    Christoph Paasch.

 8) Fix sja1000 driver defines to not conflict with SH port, from Marc
    Kleine-Budde.

 9) Don't call il4965_rs_use_green with a NULL station, from Colin Ian
    King.

10) Suspend/Resume in the FEC driver fail because the buffer descriptors
    are not initialized at all the moments in which they should.  Fix
    from Frank Li.

11) cpsw and davinci_emac drivers both use the wrong interface to
    restart a stopped TX queue.  Use netif_wake_queue not
    netif_start_queue, the latter is for initialization/bringup not
    active management of the queue.  From Mugunthan V N.

12) Fix regression in rate calculations done by
    psched_ratecfg_precompute(), missing u64 type promotion.  From
    Sergey Popovich.

13) Fix length overflow in tg3 VPD parsing, from Kees Cook.

14) AOE driver fails to allocate enough headroom, resulting in crashes.
    Fix from Eric Dumazet.

15) RX overflow happens too quickly in sky2 driver because pause packet
    thresholds are not programmed correctly.  From Mirko Lindner.

16) Bonding driver manages arp_interval and miimon settings incorrectly,
    disabling one unintentionally disables both.  Fix from Nikolay
    Aleksandrov.

17) smsc75xx drivers don't program the RX mac properly for jumbo frames.
    Fix from Steve Glendinning.

18) Fix off-by-one in Codel packet scheduler.  From Vijay Subramanian.

19) Fix packet corruption in atl1c by disabling MSI support, from Hannes
    Frederic Sowa.

20) netdev_rx_handler_unregister() needs a synchronize_net() to fix
    crashes in bonding driver unload stress tests.  From Eric Dumazet.

21) rxlen field of ks8851 RX packet descriptors not interpreted
    correctly (it is 12 bits not 16 bits, so needs to be masked after
    shifting the 32-bit value down 16 bits).  Fix from Max Nekludov.

22) Fix missed RX/TX enable in sh_eth driver due to mishandling of link
    change indications.  From Sergei Shtylyov.

23) Fix crashes during spurious ECI interrupts in sh_eth driver, also
    from Sergei Shtylyov.

24) dm9000 driver initialization is done wrong for revision B devices
    with DSP PHY, from Joseph CHANG.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (53 commits)
  DM9000B: driver initialization upgrade
  sh_eth: make 'link' field of 'struct sh_eth_private' *int*
  sh_eth: workaround for spurious ECI interrupt
  sh_eth: fix handling of no LINK signal
  ks8851: Fix interpretation of rxlen field.
  net: add a synchronize_net() in netdev_rx_handler_unregister()
  MAINTAINERS: Update netxen_nic maintainers list
  atl1e: drop pci-msi support because of packet corruption
  net: fq_codel: Fix off-by-one error
  net: calxedaxgmac: Wake-on-LAN fixes
  net: calxedaxgmac: fix rx ring handling when OOM
  net: core: Remove redundant call to 'nf_reset' in 'dev_forward_skb'
  smsc75xx: fix jumbo frame support
  net: fix the use of this_cpu_ptr
  bonding: fix disabling of arp_interval and miimon
  ipv6: don't accept node local multicast traffic from the wire
  sky2: Threshold for Pause Packet is set wrong
  sky2: Receive Overflows not counted
  aoe: reserve enough headroom on skbs
  line up comment for ndo_bridge_getlink
  ...