Use ice_pf_to_dev(pf) instead of &pf->pdev->dev
Use ice_pf_to_dev(vsi->back) instead of &vsi->back->pdev->dev
When a pointer to the pf instance is available, use ice_pf_to_dev
instead of ice_hw_to_dev
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 1f45ebe0 ("ice: add extra check for null Rx descriptor") moved
the call to ice_construct_skb() under a null check as Coverity reported a
possible use of null skb. However, the original call was not deleted, do so
now.

Fixes: 1f45ebe0 ("ice: add extra check for null Rx descriptor")
Reported-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

After a reset the Unit Load Status bits in the GLNVM_ULD register to check
for completion should be 0x7FF before continuing.  Update the mask to check
(minus the three reserved bits that are always set).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Logging the firmware/NVM information during driver load is redundant since
that information is also available via ethtool.  Move the functionality
found in ice_nvm_version_str() directly into ice_get_drvinfo() and remove
calling the former and logging that info during driver probe.  This also
gets rid of a bug in ice_nvm_version_str() where it returns a pointer to
a buffer which is free'ed when that function exits.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch modifies link message logging to include "Full Duplex" and
"Negotiated" for FEC, so as to distinguish it from "Requested" FEC.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove unnecessary CONFIG_PCI_IOV wrapping in ice_set_pf_caps. None
of the data structures accessed within the block are wrapped with
this flag. When CONFIG_PCI_IOV is undefined, pf->num_vfs_supported
will be 0 anyway.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice_dev_onetime_setup contains driver workarounds needed for
firmware limitations. These issues have now been resolved in newer
NVMs so remove the function.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we compare the value we are about to write to the Rx tail
register with the previous value of next_to_use. The problem with this
is we only write tail on 8 descriptor boundaries, but next_to_use is
updated whenever we clean Rx descriptors. Fix this by comparing the
value we are about to write to tail with the previously written tail
value. This will prevent duplicate Rx tail bumps.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Display all of the supported and advertised link modes based on the PHY
capability with media.

Displaying all supported modes is more informative then only displaying
the current link mode.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When switching between FW and SW LLDP mode, the
number of configured TLV apps in the driver's
DCB configuration is getting out of synch with
what lldpad thinks is configured.  This is causing
a problem when shutting down lldpad.  The cleanup
is trying to delete TLV apps that are not defined
in the kernel.

Since the driver is keeping an accurate account
of the apps defined, use the drivers number of
apps to determine if there is an app to delete.
If the number of apps is <= 1, then do not
attempt to delete.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The function ice_dcb_rebuild had some logic
flaws in it, and also didn't differentiate
between FW and SW modes needs.

For FW flow, the willing setting was being
forced to OFF and left that way.  Unwilling
in DCB FW mode is not a supported model.

Leave the config alone and use the return value
from the set command to determine if setting the
config was successful.

The SW DCB flow does not need to need to register
for MIB change events (as they are not used in
SW mode).

Use !is_sw_lldp checks to only perform FW specific
task while in FW mode.

Also adding a reapplication of the current DCB
config after a link event.  Some NVMs are not
maintaining their DCB configs across link events.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This allows you to specify the type of rgmii-id that will enable phy
internal delay in ethernet phy-mode.

This adds all RGMII cases to all of get_pinmode() except LD11, because LD11
SoC doesn't support RGMII due to the constraint of the hardware. When RGMII
phy mode is specified in the devicetree for LD11, the driver will abort
with an error.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent months, our customer reported several kernel crashes all
preceding with following message:
NETDEV WATCHDOG: eth2 (enic): transmit queue 0 timed out
Error message of one of those crashes:
BUG: unable to handle kernel paging request at ffffffffa007e090

After analyzing severl vmcores, I found that most of crashes are
caused by memory corruption. And all the corrupted memory areas
are overwritten by data of network packets. Moreover, I also found
that the tx queues were enabled over watchdog reset.

After going through the source code, I found that in enic_stop(),
the tx queues stopped by netif_tx_disable() could be woken up over
a small time window between netif_tx_disable() and the
napi_disable() by the following code path:
napi_poll->
  enic_poll_msix_wq->
     vnic_cq_service->
        enic_wq_service->
           netif_wake_subqueue(enic->netdev, q_number)->
              test_and_clear_bit(__QUEUE_STATE_DRV_XOFF, &txq->state)
In turn, upper netowrk stack could queue skb to ENIC NIC though
enic_hard_start_xmit(). And this might introduce some race condition.

Our customer comfirmed that this kind of kernel crash doesn't occur over
90 days since they applied this patch.
Signed-off-by: Firo Yang <firo.yang@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sameeh Jubran says:

====================
Bug fixes for ENA Ethernet driver

Difference from V1:
* Started using netdev_rss_key_fill()
* Dropped superflous changes that are not related to bug fixes as
  requested by Jakub
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

comp_ctx can be NULL in a very rare case when an admin command is executed
during the execution of ena_remove().

The bug scenario is as follows:

* ena_destroy_device() sets the comp_ctx to be NULL
* An admin command is executed before executing unregister_netdev(),
  this can still happen because our device can still receive callbacks
  from the netdev infrastructure such as ethtool commands.
* When attempting to access the comp_ctx, the bug occurs since it's set
  to NULL

Fix:
Added a check that comp_ctx is not NULL

Fixes: 1738cd3e ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Up till kernel 4.11 there was no enum defined for crc32 hash in ethtool,
thus the xor enum was used for supporting crc32.

Fixes: 1738cd3e ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As the name suggests ETH_RSS_HASH_NO_CHANGE is received upon changing
the key or indirection table using ethtool while keeping the same hash
function.

Also add a function for retrieving the current hash function from
the ena-com layer.

Fixes: 1738cd3e ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Saeed Bshara <saeedb@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function ena_com_ind_tbl_convert_from_device() has an overflow
bug as explained below. Either way, this function is not needed at
all since we don't retrieve the indirection table from the device
at any point which means that this conversion is not needed.

The bug:
The for loop iterates over all io_sq_queues, when passing the actual
number of used queues the io_sq_queues[i].idx equals 0 since they are
uninitialized which results in the following code to be executed till
the end of the loop:

dev_idx_to_host_tbl[0] = i;

This results dev_idx_to_host_tbl[0] in being equal to
ENA_TOTAL_NUM_QUEUES - 1.

Fixes: 1738cd3e ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The indirection table has the indices of the Rx queues. When we store it
during set indirection operation, we convert the indices to our internal
representation of the indices.

Our internal representation of the indices is: even indices for Tx and
uneven indices for Rx, where every Tx/Rx pair are in a consecutive order
starting from 0. For example if the driver has 3 queues (3 for Tx and 3
for Rx) then the indices are as follows:
0  1  2  3  4  5
Tx Rx Tx Rx Tx Rx

The BUG:
The issue is that when we satisfy a get request for the indirection
table, we don't convert the indices back to the original representation.

The FIX:
Simply apply the inverse function for the indices of the indirection
table after we set it.

Fixes: 1738cd3e ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The device receives, stores and retrieves the hash function value as bits
and not as their enum value.

The bug:
* In ena_com_set_hash_function() we set
  cmd.u.flow_hash_func.selected_func to the bit value of rss->hash_func.
 (1 << rss->hash_func)
* In ena_com_get_hash_function() we retrieve the hash function and store
  it's bit value in rss->hash_func. (Now the bit value of rss->hash_func
  is stored in rss->hash_func instead of it's enum value)

The fix:
This commit fixes the issue by converting the retrieved hash function
values from the device to the matching enum value of the set bit using
ffs(). ffs() finds the first set bit's index in a word. Since the function
returns 1 for the LSB's index, we need to subtract 1 from the returned
value (note that BIT(0) is 1).

Fixes: 1738cd3e ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On old hardware, getting / setting the hash function is not supported while
gettting / setting the indirection table is.

This commit enables us to still show the indirection table on older
hardwares by setting the hash function and key to NULL.

Fixes: 1738cd3e ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently we allocate the key whether the device supports setting the
key or not. This commit adds a check to the allocation function and
handles the error accordingly.

Fixes: 1738cd3e ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bug description:
When running "ethtool -x <if_name>" the key shows up as all zeros.

When we use "ethtool -X <if_name> hfunc toeplitz hkey <some:random:key>" to
set the key and then try to retrieve it using "ethtool -x <if_name>" then
we return the correct key because we return the one we saved.

Bug cause:
We don't fetch the key from the device but instead return the key
that we have saved internally which is by default set to zero upon
allocation.

Fix:
This commit fixes the issue by initializing the key to a random value
using netdev_rss_key_fill().

Fixes: 1738cd3e ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current implementation of the driver calls skb_tx_timestamp()to add a
software tx timestamp to the skb, however the software-transmit capability
is not reported in ethtool -T.

This commit updates the ethtool structure to report the software-transmit
capability in ethtool -T using the standard ethtool_op_get_ts_info().
This function reports all software timestamping capabilities (tx and rx),
as well as setting phc_index = -1. phc_index is the index of the PTP
hardware clock device that will be used for hardware timestamps. Since we
don't have such a device in ENA, using the default -1 value is the correct
setting.

Fixes: 1738cd3e ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Ezequiel Lara Gomez <ezegomez@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

>From the documentation of round_jiffies():
"Rounds a time delta  in the future (in jiffies) up or down to
(approximately) full seconds. This is useful for timers for which
the exact time they fire does not matter too much, as long as
they fire approximately every X seconds.
By rounding these timers to whole seconds, all such timers will fire
at the same time, rather than at various times spread out. The goal
of this is to have the CPU wake up less, which saves power."

There are 2 parts to this patch:
================================
Part 1:
-------
In our case we need timer_service to be called approximately every
X=1 seconds, and the exact time does not matter, so using round_jiffies()
is the right way to go.

Therefore we add round_jiffies() to the mod_timer() in ena_timer_service().

Part 2:
-------
round_jiffies() is used in check_for_missing_keep_alive() when
getting the jiffies of the expiration of the keep_alive timeout. Here it
is actually a mistake to use round_jiffies() because we want the exact
time when keep_alive should expire and not an approximate rounded time,
which can cause early, false positive, timeouts.

Therefore we remove round_jiffies() in the calculation of
keep_alive_expired() in check_for_missing_keep_alive().

Fixes: 82ef30f1 ("net: ena: add hardware hints capability to the driver")
Fixes: 1738cd3e ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When ethtool -X is called without an hkey, ena_com_fill_hash_function()
is called with key=NULL, which is passed to memcpy causing a crash.

This commit fixes this issue by checking key is not NULL.

Fixes: 1738cd3e ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As nlmsg_put() does not clear the memory that is reserved,
it this the caller responsability to make sure all of this
memory will be written, in order to not reveal prior content.

While we are at it, we can provide the socket cookie even
if clsock is not set.

syzbot reported :

BUG: KMSAN: uninit-value in __arch_swab32 arch/x86/include/uapi/asm/swab.h:10 [inline]
BUG: KMSAN: uninit-value in __fswab32 include/uapi/linux/swab.h:59 [inline]
BUG: KMSAN: uninit-value in __swab32p include/uapi/linux/swab.h:179 [inline]
BUG: KMSAN: uninit-value in __be32_to_cpup include/uapi/linux/byteorder/little_endian.h:82 [inline]
BUG: KMSAN: uninit-value in get_unaligned_be32 include/linux/unaligned/access_ok.h:30 [inline]
BUG: KMSAN: uninit-value in ____bpf_skb_load_helper_32 net/core/filter.c:240 [inline]
BUG: KMSAN: uninit-value in ____bpf_skb_load_helper_32_no_cache net/core/filter.c:255 [inline]
BUG: KMSAN: uninit-value in bpf_skb_load_helper_32_no_cache+0x14a/0x390 net/core/filter.c:252
CPU: 1 PID: 5262 Comm: syz-executor.5 Not tainted 5.5.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x1c9/0x220 lib/dump_stack.c:118
 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118
 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215
 __arch_swab32 arch/x86/include/uapi/asm/swab.h:10 [inline]
 __fswab32 include/uapi/linux/swab.h:59 [inline]
 __swab32p include/uapi/linux/swab.h:179 [inline]
 __be32_to_cpup include/uapi/linux/byteorder/little_endian.h:82 [inline]
 get_unaligned_be32 include/linux/unaligned/access_ok.h:30 [inline]
 ____bpf_skb_load_helper_32 net/core/filter.c:240 [inline]
 ____bpf_skb_load_helper_32_no_cache net/core/filter.c:255 [inline]
 bpf_skb_load_helper_32_no_cache+0x14a/0x390 net/core/filter.c:252

Uninit was created at:
 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:144 [inline]
 kmsan_internal_poison_shadow+0x66/0xd0 mm/kmsan/kmsan.c:127
 kmsan_kmalloc_large+0x73/0xc0 mm/kmsan/kmsan_hooks.c:128
 kmalloc_large_node_hook mm/slub.c:1406 [inline]
 kmalloc_large_node+0x282/0x2c0 mm/slub.c:3841
 __kmalloc_node_track_caller+0x44b/0x1200 mm/slub.c:4368
 __kmalloc_reserve net/core/skbuff.c:141 [inline]
 __alloc_skb+0x2fd/0xac0 net/core/skbuff.c:209
 alloc_skb include/linux/skbuff.h:1049 [inline]
 netlink_dump+0x44b/0x1ab0 net/netlink/af_netlink.c:2224
 __netlink_dump_start+0xbb2/0xcf0 net/netlink/af_netlink.c:2352
 netlink_dump_start include/linux/netlink.h:233 [inline]
 smc_diag_handler_dump+0x2ba/0x300 net/smc/smc_diag.c:242
 sock_diag_rcv_msg+0x211/0x610 net/core/sock_diag.c:256
 netlink_rcv_skb+0x451/0x650 net/netlink/af_netlink.c:2477
 sock_diag_rcv+0x63/0x80 net/core/sock_diag.c:275
 netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline]
 netlink_unicast+0xf9e/0x1100 net/netlink/af_netlink.c:1328
 netlink_sendmsg+0x1248/0x14d0 net/netlink/af_netlink.c:1917
 sock_sendmsg_nosec net/socket.c:639 [inline]
 sock_sendmsg net/socket.c:659 [inline]
 kernel_sendmsg+0x433/0x440 net/socket.c:679
 sock_no_sendpage+0x235/0x300 net/core/sock.c:2740
 kernel_sendpage net/socket.c:3776 [inline]
 sock_sendpage+0x1e1/0x2c0 net/socket.c:937
 pipe_to_sendpage+0x38c/0x4c0 fs/splice.c:458
 splice_from_pipe_feed fs/splice.c:512 [inline]
 __splice_from_pipe+0x539/0xed0 fs/splice.c:636
 splice_from_pipe fs/splice.c:671 [inline]
 generic_splice_sendpage+0x1d5/0x2d0 fs/splice.c:844
 do_splice_from fs/splice.c:863 [inline]
 do_splice fs/splice.c:1170 [inline]
 __do_sys_splice fs/splice.c:1447 [inline]
 __se_sys_splice+0x2380/0x3350 fs/splice.c:1427
 __x64_sys_splice+0x6e/0x90 fs/splice.c:1427
 do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: f16a7dd5 ("smc: netlink interface for SMC sockets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit d9d6a9ae ("i40e: Fix virtchnl_queue_select bitmap
validation") introduced a necessary change for verifying how queue
bitmaps from the iavf driver get validated. Unfortunately, the
conditional was reversed. Fix this.

Fixes: d9d6a9ae ("i40e: Fix virtchnl_queue_select bitmap validation")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current generic XDP handler skips execution of XDP programs entirely if
an SKB is marked as cloned. This leads to some surprising behaviour, as
packets can end up being cloned in various ways, which will make an XDP
program not see all the traffic on an interface.

This was discovered by a simple test case where an XDP program that always
returns XDP_DROP is installed on a veth device. When combining this with
the Scapy packet sniffer (which uses an AF_PACKET) socket on the sending
side, SKBs reliably end up in the cloned state, causing them to be passed
through to the receiving interface instead of being dropped. A minimal
reproducer script for this is included below.

This patch fixed the issue by simply triggering the existing linearisation
code for cloned SKBs instead of skipping the XDP program execution. This
behaviour is in line with the behaviour of the native XDP implementation
for the veth driver, which will reallocate and copy the SKB data if the SKB
is marked as shared.

Reproducer Python script (requires BCC and Scapy):

from scapy.all import TCP, IP, Ether, sendp, sniff, AsyncSniffer, Raw, UDP
from bcc import BPF
import time, sys, subprocess, shlex

SKB_MODE = (1 << 1)
DRV_MODE = (1 << 2)
PYTHON=sys.executable

def client():
    time.sleep(2)
    # Sniffing on the sender causes skb_cloned() to be set
    s = AsyncSniffer()
    s.start()

    for p in range(10):
        sendp(Ether(dst="aa:aa:aa:aa:aa:aa", src="cc:cc:cc:cc:cc:cc")/IP()/UDP()/Raw("Test"),
              verbose=False)
        time.sleep(0.1)

    s.stop()
    return 0

def server(mode):
    prog = BPF(text="int dummy_drop(struct xdp_md *ctx) {return XDP_DROP;}")
    func = prog.load_func("dummy_drop", BPF.XDP)
    prog.attach_xdp("a_to_b", func, mode)

    time.sleep(1)

    s = sniff(iface="a_to_b", count=10, timeout=15)
    if len(s):
        print(f"Got {len(s)} packets - should have gotten 0")
        return 1
    else:
        print("Got no packets - as expected")
        return 0

if len(sys.argv) < 2:
    print(f"Usage: {sys.argv[0]} <skb|drv>")
    sys.exit(1)

if sys.argv[1] == "client":
    sys.exit(client())
elif sys.argv[1] == "server":
    mode = SKB_MODE if sys.argv[2] == 'skb' else DRV_MODE
    sys.exit(server(mode))
else:
    try:
        mode = sys.argv[1]
        if mode not in ('skb', 'drv'):
            print(f"Usage: {sys.argv[0]} <skb|drv>")
            sys.exit(1)
        print(f"Running in {mode} mode")

        for cmd in [
                'ip netns add netns_a',
                'ip netns add netns_b',
                'ip -n netns_a link add a_to_b type veth peer name b_to_a netns netns_b',
                # Disable ipv6 to make sure there's no address autoconf traffic
                'ip netns exec netns_a sysctl -qw net.ipv6.conf.a_to_b.disable_ipv6=1',
                'ip netns exec netns_b sysctl -qw net.ipv6.conf.b_to_a.disable_ipv6=1',
                'ip -n netns_a link set dev a_to_b address aa:aa:aa:aa:aa:aa',
                'ip -n netns_b link set dev b_to_a address cc:cc:cc:cc:cc:cc',
                'ip -n netns_a link set dev a_to_b up',
                'ip -n netns_b link set dev b_to_a up']:
            subprocess.check_call(shlex.split(cmd))

        server = subprocess.Popen(shlex.split(f"ip netns exec netns_a {PYTHON} {sys.argv[0]} server {mode}"))
        client = subprocess.Popen(shlex.split(f"ip netns exec netns_b {PYTHON} {sys.argv[0]} client"))

        client.wait()
        server.wait()
        sys.exit(server.returncode)

    finally:
        subprocess.run(shlex.split("ip netns delete netns_a"))
        subprocess.run(shlex.split("ip netns delete netns_b"))

Fixes: d4455169 ("net: xdp: support xdp generic on virtual devices")
Reported-by: Stepan Horacek <shoracek@redhat.com>
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We have been using the fact that the QMI and DIAG functions
usually are the only ones with class/subclass/protocol being
ff/ff/ff on Quectel modems. This has allowed us to match the
QMI function without knowing the exact interface number,
which can vary depending on firmware configuration.

The ability to silently reject the DIAG function, which is
usually handled by the option driver, is important for this
method to work.  This is done based on the knowledge that it
has exactly 2 bulk endpoints.  QMI function control interfaces
will have either 3 or 1 endpoint. This rule is universal so
the quirk condition can be removed.

The fixed layouts known from the Gobi1k and Gobi2k modems
have been gradually replaced by more dynamic layouts, and
many vendors now use configurable layouts without changing
device IDs.  Renaming the class/subclass/protocol matching
macro makes it more obvious that this is now not Quectel
specific anymore.

Cc: Kristian Evensen <kristian.evensen@gmail.com>
Cc: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

When adding support for unique interrupt names, after testing on a few
devices, it was assumed 32 characters would be sufficient. This
assumption turned out to be incorrect, ZII RDU2 for example uses a
device base name of mv88e6xxx-30be0000.ethernet-1:0, leaving no space
for post fixes such as -g1-atu-prob and -watchdog. The names then
become identical, defeating the point of the patch.

Increase the length of the string to 64 charactoes.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 3095383a ("net: dsa: mv88e6xxx: Unique IRQ name")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit f25e1392 removed the support for the pre-production variant
of the Dell DW5821e to avoid probing another USB interface unnecessarily.
However, the pre-production samples are found in the wild, and this lack
of support is causing problems for users of such samples.  It is therefore
necessary to support both variants.

Matching on both interfaces 0 and 1 is not expected to cause any problem
with either variant, as only the QMI function will be probed successfully
on either.  Interface 1 will be rejected based on the HID class for the
production variant:

T:  Bus=01 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  2
P:  Vendor=413c ProdID=81d7 Rev=03.18
S:  Manufacturer=DELL
S:  Product=DW5821e Snapdragon X20 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=00 Prot=00 Driver=usbhid
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option

And interface 0 will be rejected based on too few endpoints for the
pre-production variant:

T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=03 Dev#= 7 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 2
P: Vendor=413c ProdID=81d7 Rev= 3.18
S: Manufacturer=DELL
S: Product=DW5821e Snapdragon X20 LTE
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option

Fixes: f25e1392 ("qmi_wwan: fix interface number for DW5821e production firmware")
Link: https://whrl.pl/Rf0vNkReported-by: Lars Melin <larsm17@gmail.com>
Cc: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 9546a0b7 ("tipc: fix wrong connect() return code"), we
fixed the issue with the 'connect()' that returns zero even though the
connecting has failed by waiting for the connection to be 'ESTABLISHED'
really. However, the approach has one drawback in conjunction with our
'lightweight' connection setup mechanism that the following scenario
can happen:

          (server)                        (client)

   +- accept()|                      |             wait_for_conn()
   |          |                      |connect() -------+
   |          |<-------[SYN]---------|                 > sleeping
   |          |                      *CONNECTING       |
   |--------->*ESTABLISHED           |                 |
              |--------[ACK]-------->*ESTABLISHED      > wakeup()
        send()|--------[DATA]------->|\                > wakeup()
        send()|--------[DATA]------->| |               > wakeup()
          .   .          .           . |-> recvq       .
          .   .          .           . |               .
        send()|--------[DATA]------->|/                > wakeup()
       close()|--------[FIN]-------->*DISCONNECTING    |
              *DISCONNECTING         |                 |
              |                      ~~~~~~~~~~~~~~~~~~> schedule()
                                                       | wait again
                                                       .
                                                       .
                                                       | ETIMEDOUT

Upon the receipt of the server 'ACK', the client becomes 'ESTABLISHED'
and the 'wait_for_conn()' process is woken up but not run. Meanwhile,
the server starts to send a number of data following by a 'close()'
shortly without waiting any response from the client, which then forces
the client socket to be 'DISCONNECTING' immediately. When the wait
process is switched to be running, it continues to wait until the timer
expires because of the unexpected socket state. The client 'connect()'
will finally get ‘-ETIMEDOUT’ and force to release the socket whereas
there remains the messages in its receive queue.

Obviously the issue would not happen if the server had some delay prior
to its 'close()' (or the number of 'DATA' messages is large enough),
but any kind of delay would make the connection setup/shutdown "heavy".
We solve this by simply allowing the 'connect()' returns zero in this
particular case. The socket is already 'DISCONNECTING', so any further
write will get '-EPIPE' but the socket is still able to read the
messages existing in its receive queue.

Note: This solution doesn't break the previous one as it deals with a
different situation that the socket state is 'DISCONNECTING' but has no
error (i.e. sk->sk_err = 0).

Fixes: 9546a0b7 ("tipc: fix wrong connect() return code")
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the following sparse warning:
net/mptcp/protocol.c:646:13: warning: symbol 'mptcp_sk_clone_lock' was not declared. Should it be static?

Fixes: b0519de8 ("mptcp: fix use-after-free for ipv6")
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the following sparse warning:

net/tipc/node.c:281:6: warning: symbol 'tipc_node_free' was not declared. Should it be static?
net/tipc/node.c:2801:5: warning: symbol '__tipc_nl_node_set_key' was not declared. Should it be static?
net/tipc/node.c:2878:5: warning: symbol '__tipc_nl_node_flush_key' was not declared. Should it be static?

Fixes: fc1b6d6d ("tipc: introduce TIPC encryption & authentication")
Fixes: e1f32190 ("tipc: add support for AEAD key setting via netlink")
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull misc SCSI fixes from James Bottomley:
 "Five small patches, all in drivers or doc, which missed the initial
  pull request.

  The qla2xxx and megaraid_sas are actual fixes and the rest are
  spelling and doc changes"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ufs: fix spelling mistake "initilized" -> "initialized"
  scsi: pm80xx: fix spelling mistake "to" -> "too"
  scsi: MAINTAINERS: ufs: remove pedrom.sousa@synopsys.com
  scsi: megaraid_sas: fixup MSIx interrupt setup during resume
  scsi: qla2xxx: Fix unbound NVME response length

Pull networking fixes from David Miller:

 1) Unbalanced locking in mwifiex_process_country_ie, from Brian Norris.

 2) Fix thermal zone registration in iwlwifi, from Andrei
    Otcheretianski.

 3) Fix double free_irq in sgi ioc3 eth, from Thomas Bogendoerfer.

 4) Use after free in mptcp, from Florian Westphal.

 5) Use after free in wireguard's root_remove_peer_lists, from Eric
    Dumazet.

 6) Properly access packets heads in bonding alb code, from Eric
    Dumazet.

 7) Fix data race in skb_queue_len(), from Qian Cai.

 8) Fix regression in r8169 on some chips, from Heiner Kallweit.

 9) Fix XDP program ref counting in hv_netvsc, from Haiyang Zhang.

10) Certain kinds of set link netlink operations can cause a NULL deref
    in the ipv6 addrconf code. Fix from Eric Dumazet.

11) Don't cancel uninitialized work queue in drop monitor, from Ido
    Schimmel.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
  net: thunderx: use proper interface type for RGMII
  mt76: mt7615: fix max_nss in mt7615_eeprom_parse_hw_cap
  bpf: Improve bucket_log calculation logic
  selftests/bpf: Test freeing sockmap/sockhash with a socket in it
  bpf, sockhash: Synchronize_rcu before free'ing map
  bpf, sockmap: Don't sleep while holding RCU lock on tear-down
  bpftool: Don't crash on missing xlated program instructions
  bpf, sockmap: Check update requirements after locking
  drop_monitor: Do not cancel uninitialized work item
  mlxsw: spectrum_dpipe: Add missing error path
  mlxsw: core: Add validation of hardware device types for MGPIR register
  mlxsw: spectrum_router: Clear offload indication from IPv6 nexthops on abort
  selftests: mlxsw: Add test cases for local table route replacement
  mlxsw: spectrum_router: Prevent incorrect replacement of local table routes
  net: dsa: microchip: enable module autoprobe
  ipv6/addrconf: fix potential NULL deref in inet6_set_link_af()
  dpaa_eth: support all modes with rate adapting PHYs
  net: stmmac: update pci platform data to use phy_interface
  net: stmmac: xgmac: fix missing IFF_MULTICAST checki in dwxgmac2_set_filter
  net: stmmac: fix missing IFF_MULTICAST check in dwmac4_set_filter
  ...

Pull powerpc fixes from Michael Ellerman:

 - Fix an existing bug in our user access handling, exposed by one of
   the bug fixes we merged this cycle.

 - A fix for a boot hang on 32-bit with CONFIG_TRACE_IRQFLAGS and the
   recently added CONFIG_VMAP_STACK.

Thanks to: Christophe Leroy, Guenter Roeck.

* tag 'powerpc-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc: Fix CONFIG_TRACE_IRQFLAGS with CONFIG_VMAP_STACK
  powerpc/futex: Fix incorrect user access blocking

This is a merge error on my part - the driver was merged into mainline
by commit c5951e7c ("Merge tag 'mips_5.6' of git://../mips/linux")
over a week ago, but nobody apparently noticed that it didn't actually
build due to still having a reference to the devm_ioremap_nocache()
function, removed a few days earlier through commit 6a1000bd ("Merge
tag 'ioremap-5.6' of git://../ioremap").

Apparently this didn't get any build testing anywhere.  Not perhaps all
that surprising: it's restricted to 64-bit MIPS only, and only with the
new SGI_MFD_IOC3 support enabled.

I only noticed because the ioremap conflicts in the ARM SoC driver
update made me check there weren't any others hiding, and I found this
one.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ARM SoC late updates from Olof Johansson:
 "This is some material that we picked up into our tree late, or that
  had more complex dependencies on more than one topic branch that makes
  sense to keep separately.

   - TI support for secure accelerators and hwrng on OMAP4/5

   - TI camera changes for dra7 and am437x and SGX improvement due to
     better reset control support on am335x, am437x and dra7

   - Davinci moves to proper clocksource on DM365, and regulator/audio
     improvements for DM365 and DM644x eval boards"

* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
  ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem
  ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt
  ARM: dts: Configure interconnect target module for am437x sgx
  ARM: dts: Configure sgx for dra7
  ARM: dts: Configure rstctrl reset for am335x SGX
  ARM: dts: dra7: Add ti-sysc node for VPE
  ARM: dts: dra7: add vpe clkctrl node
  ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries
  ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries
  ARM: dts: am43xx: add support for clkout1 clock
  arm: dts: dra76-evm: Add CAL and OV5640 nodes
  arm: dtsi: dra76x: Add CAL dtsi node
  arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
  ARM: dts: DRA72: Add CAL dtsi node
  ARM: dts: dra7-l4: Add ti-sysc node for CAM
  ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
  ARM: dts: dra7: add cam clkctrl node
  ARM: OMAP2+: Drop legacy platform data for omap4 des
  ARM: OMAP2+: Drop legacy platform data for omap4 sham
  ARM: OMAP2+: Drop legacy platform data for omap4 aes
  ...