ipv6: Make 'addrconf_rs_timer' send Router Solicitations (and re-arm itself) if Router Advertisements are accepted

As of 026359bc [ipv6: Send ICMPv6 RSes only when RAs are accepted],
Router Solicitations are sent whenever kernel accepts Router
Advertisements on the interface.

However, this logic isn't reflected in 'addrconf_rs_timer'.

The timer fails to issue subsequent RS messages (and fails to re-arm
itself) if forwarding is enabled and the special hybrid mode is
enabled (accept_ra=2).

Fix the condition determining whether next RS should be sent, by using
'ipv6_accept_ra()'.
Reported-by: Ami Koren <amikoren@yahoo.com>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The cleanup sequence in sky2_probe() that is called in case of an error is
mixed up in different places:

- pci_disable_device() is not called in each case the device has been enabled
before

- same for pci_disable_msi(): test_msi() may return with an error != EOPNOTSUPP
(due to failure of request_irq()). In that case msi is not disabled

- also failure of register_netdev() does not disable msi

This patch fixes the concerning parts.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 8139cp driver has a change_mtu function that has not been
enabled since the dawn of the git repository. However, the
generic eth_change_mtu is not used in its place, so that
invalid MTU values can be set on the interface.

Original patch salvages the broken code for the single case of
setting the MTU while the interface is down, which is safe
and also includes the range check.  Now enhanced to support up
or down interface.

v2: fix case where rxbufsz isn't changed in the up state case

Original patch from
http://lkml.indiana.edu/hypermail/linux/kernel/1202.2/00770.html

Testing: has been test on virtual 8139cp setup without issue,
have no access real hardware 8139cp, need testing help.
Signed-off-by: "John Greene" <jogreene@redhat.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

We attach queue 0 after registering netdevice currently. This leads to call
netif_set_real_num_{tx|rx}_queues() after registering the netdevice. Since we
allow tun/tap has a maximum of 1024 queues, this may lead a huge number of
uevents to be injected to userspace since we create 2048 kobjects and then
remove 2046. Solve this problem by attaching queue 0 and set the real number of
queues before registering netdevice.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Tested-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If fan failure is detected, MCP prevents PCI I/O registers from being
mapped to the bar, causing a fatal error as driver is unaware.

This patch recognizes such an event occurred and gracefully terminates
the probe process.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These packet counters are used to drive the zercopy
selection heuristic so nothing too bad happens if they are off a bit -
and they are also reset once in a while.
But it's cleaner to clear them when backend is set so that
we start in a known state.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Two macros have been defined twice, remove them.
Signed-off-by: Liming Wang <walimisdev@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable WoL support.
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current SCTP stack is lacking a mechanism to have per association
statistics. This is an implementation modeled after OpenSolaris'
SCTP_GET_ASSOC_STATS.

Userspace part will follow on lksctp if/when there is a general ACK on
this.
V4:
- Move ipackets++ before q->immediate.func() for consistency reasons
- Move sctp_max_rto() at the end of sctp_transport_update_rto() to avoid
  returning bogus RTO values
- return asoc->rto_min when max_obs_rto value has not changed

V3:
- Increase ictrlchunks in sctp_assoc_bh_rcv() as well
- Move ipackets++ to sctp_inq_push()
- return 0 when no rto updates took place since the last call

V2:
- Implement partial retrieval of stat struct to cope for future expansion
- Kill the rtxpackets counter as it cannot be precise anyway
- Rename outseqtsns to outofseqtsns to make it clearer that these are out
  of sequence unexpected TSNs
- Move asoc->ipackets++ under a lock to avoid potential miscounts
- Fold asoc->opackets++ into the already existing asoc check
- Kill unneeded (q->asoc) test when increasing rtxchunks
- Do not count octrlchunks if sending failed (SCTP_XMIT_OK != 0)
- Don't count SHUTDOWNs as SACKs
- Move SCTP_GET_ASSOC_STATS to the private space API
- Adjust the len check in sctp_getsockopt_assoc_stats() to allow for
  future struct growth
- Move association statistics in their own struct
- Update idupchunks when we send a SACK with dup TSNs
- return min_rto in max_rto when RTO has not changed. Also return the
  transport when max_rto last changed.

Signed-off: Michele Baldessari <michele@acksyn.org>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch converts ep7211-sir driver to platform_driver.
Since driver can be used not only for EP7211 CPU, function names
was be renamed to generic clps711x...
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

These calls are followed by calls to memcpy() on the same memory area, so they
can safely be removed.
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TCP coalescing added a regression in splice(socket->pipe) performance,
for some workloads because of the way tcp_read_sock() is implemented.

The reason for this is the break when (offset + 1 != skb->len).

As we released the socket lock, this condition is possible if TCP stack
added a fragment to the skb, which can happen with TCP coalescing.

So let's go back to the beginning of the loop when this happens,
to give a chance to splice more frags per system call.

Doing so fixes the issue and makes GRO 10% faster than LRO
on CPU-bound splice() workloads instead of the opposite.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

# make C=2 CF=-D__CHECK_ENDIAN__ net/ipv4/inet_hashtables.o
...
net/ipv4/inet_hashtables.c:242:7: warning: restricted __portpair degrades to integer
net/ipv4/inet_hashtables.c:242:7: warning: restricted __addrpair degrades to integer
...

Move __portpair/__addrpair from include/net/inet_hashtables.h
to include/net/sock.h where we need them in struct sock_common
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ling Ma <ling.ma.program@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x driver could only have enabled pfc via usage of dcbnl; now, it can
also correctly disable it.
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When configuring pauses using 'ethtool -A', the requested values have
effect when used together with autoneg (up to this point, when configured
for autoneg, driver ignored requested pause configuration)
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A rare case of no link due to a missed interrupt may occur due to a
race condition between acknowledging the IGU via the BAR and restoring the NIG
interrupt mask via the GRC.
To solve it, we wait for the IGU ack command to finish prior to restoring the
NIG interrupt mask.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unmasked interrupt caused "FATAL HW block attention set2 0x20" messages
to erroneously appear, as the associated interrupt is fully recoverable.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If IGU parse error is encountered during the probing process, the error
propagates and the probe gracefully fails (until now, such errors were ignored,
later causing mischief).
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is now possible to enable dropless flow control via nvram.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If link is down due to management (and not due to actual phy link being lost),
driver should still behave as if the link is down; Querying via ethtool about
speed/duplex state should result in 'UNKNOWN' (same behaviour as when link is
actually down).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Whenever bnx2x fails to transmit a packet due to a full Tx ring, if the
ring size is zero (indicating an FCoE ring) driver filters the packet out
and gracefully continues.
Driver also gathers statistics on such filtered packets.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If configured for PFC/ETS by management, configure chip regardless of the
presence of a remote peer which supports DCBX.
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Parity recovery was enhanced in order to handle a few more corner cases.
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changed naming convention of SPIO macros, and prevented access to invalid SPIOs.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support to changing number of rx/tx channels using
ethtool ('ethtool -[lL]'). Where the number of tx channels specified in ethtool
is the number of rings per user priority - not total number of tx rings.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to re-set tx moderation information after calling set_ringparam
else default tx moderation will be used.
Also avoid related code duplication, by putting it in a utility function.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set mlx4_en maintainer to Amir Vadai instead of Yevgeny Petrilin.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Woodhouse says:

====================
This is the result of pulling on the thread started by Krzysztof Mazur's
original patch 'pppoatm: don't send frames to destroyed vcc'.

Various problems in the pppoatm and br2684 code are solved, some of which
were easily triggered and would panic the kernel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

No idea why we've gone so long dumping a list of VCCs with vci==0 on
every ->open() call...
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

 - Flush pending TX skbs from the queue rather than waiting for them all to
   complete (suggested by Krzysztof Mazur <krzysiek@podlesie.net>).
 - Clear ATM_VF_ADDR only when the PKT_PCLOSE packet has been submitted.
 - Don't clear ATM_VF_READY at all — vcc_destroy_socket() does that for us.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

We don't need to schedule the wakeup tasklet on *every* unlock; only if we
actually blocked the channel in the first place.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Krzysztof Mazur <krzysiek@podlesie.net>

The br2684 does not check if used vcc is in connected state,
causing potential Oops in pppoatm_send() when vcc->send() is called
on not fully connected socket.

Now br2684 can be assigned only on connected sockets; otherwise
-EINVAL error is returned.
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

... and ensure that the next skb is set up for RX in the DMA case.
Signed-off-by: Nathan Williams <nathan@traverse.com.au>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The br2684 code used module_put() during unassignment from vcc with
hope that we have BKL. This assumption is no longer true.

Now owner field in atmvcc is used to move this module_put()
to vcc_destroy_socket().
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Krzysztof Mazur <krzysiek@podlesie.net>

Now that we can return zero from pppoatm_send() for reasons *other* than
the queue being full, that means we can't depend on a subsequent call to
pppoatm_pop() waking the queue, and we might leave it stalled
indefinitely.

Use the ->release_cb() callback to wake the queue after the sock is
unlocked.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Krzysztof Mazur <krzysiek@podlesie.net>

Avoid submitting packets to a vcc which is being closed. Things go badly
wrong when the ->pop method gets later called after everything's been
torn down.

Use the ATM socket lock for synchronisation with vcc_destroy_socket(),
which clears the ATM_VF_READY bit under the same lock. Otherwise, we
could end up submitting a packet to the device driver even after its
->ops->close method has been called. And it could call the vcc's ->pop
method after the protocol has been shut down. Which leads to a panic.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Krzysztof Mazur <krzysiek@podlesie.net>

The immediate use case for this is that it will allow us to ensure that a
pppoatm queue is woken after it has to drop a packet due to the sock being
locked.

Note that 'release_cb' is called when the socket is *unlocked*. This is
not to be confused with vcc_release() — which probably ought to be called
vcc_close().
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Krzysztof Mazur <krzysiek@podlesie.net>