- 13 Feb, 2014 37 commits
-
-
Qipan Li authored
instead of using sirf specific dma channel property like "sirf,uart-dma-rx-channel" and "sirf,uart-dma-tx-channel", here we move to use generic dma dt-binding to get the channel like: - sirf,uart-dma-rx-channel = <21>; - sirf,uart-dma-tx-channel = <2>; + dmas = <&dmac1 5>, <&dmac0 2>; + dma-names = "rx", "tx"; and we move dma_request_channel() to dma_request_slave_channel(), we don't need to call sirfsoc dma filter function sirfsoc_dma_filter_id() again. Signed-off-by:
Qipan Li <Qipan.Li@csr.com> Signed-off-by:
Barry Song <Baohua.Song@csr.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Tushar Behera authored
uart_register_driver call binds the driver to a specific device node through tty_register_driver call. This should typically happen during device probe call. In a multiplatform scenario, it is possible that multiple serial drivers are part of the kernel. Currently the driver registration fails if multiple serial drivers with same default major/minor numbers are included in the kernel. A typical case is observed with amba-pl011 and samsung-uart drivers. Signed-off-by:
Tushar Behera <tushar.behera@linaro.org> Signed-off-by:
-
Tushar Behera authored
uart_register_driver call binds the driver to a specific device node through tty_register_driver call. This should typically happen during device probe call. In a multiplatform scenario, it is possible that multiple serial drivers are part of the kernel. Currently the driver registration fails if multiple serial drivers with same default major/minor numbers are included in the kernel. A typical case is observed with amba-pl011 and samsung-uart drivers. Signed-off-by:
-
Alexander Shiyan authored
config: x86_64-randconfig-x006 (attached as .config) All warnings: drivers/tty/serial/max310x.c: In function 'max310x_probe': >> drivers/tty/serial/max310x.c:1240:1: warning: label 'out_uart' defined but not used [-Wunused-label] Reported-by:
kbuild test robot <fengguang.wu@intel.com> Signed-off-by:
Alexander Shiyan <shc_work@mail.ru> Signed-off-by:
-
Alexander Shiyan authored
config: make ARCH=alpha allyesconfig All error/warnings: drivers/tty/serial/max310x.c: In function 'max310x_ioctl': >> drivers/tty/serial/max310x.c:905:7: error: 'TIOCSRS485' undeclared (first use in this function) drivers/tty/serial/max310x.c:905:7: note: each undeclared identifier is reported only once for each function it appears in >> drivers/tty/serial/max310x.c:906:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration] >> drivers/tty/serial/max310x.c:929:7: error: 'TIOCGRS485' undeclared (first use in this function) >> drivers/tty/serial/max310x.c:938:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration] cc1: some warnings being treated as errors Reported-by:
-
Huang Shijie authored
The current code only wakes up the processes when the circle buffer has less data then the WAKEUP_CHARS. But sometimes, the circle buffer may has data more then the WAKEUP_CHARS, in such case, the processes will hang. This patch makes it always wakes up the processes in the TX callback. Signed-off-by:
Huang Shijie <b32955@freescale.com> Signed-off-by:
-
Nicolas Ferre authored
This fixes a driver bug which stopped the whole system (in case of serial console). This log message is not useful anyway as this information is printed elsewhere. Signed-off-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by:
-
Peter Hurley authored
Greg, Please note this patch requires n_tty: Fix poll() when TIME_CHAR and MIN_CHAR == 0 Regards, Peter Hurley Signed-off-by: -
Greg Kroah-Hartman authored
We want the tty core fixes in here as well, because other patches depend on them. Signed-off-by: -
Joe Schultz authored
The Exar XR17V35x family of UARTs have an additional fractional divisor register (DLD) which was not being used. Calculate and set this register for these devices to reduce their baud rate error. Signed-off-by:
Joe Schultz <jschultz@xes-inc.com> Signed-off-by:
Aaron Sierra <asierra@xes-inc.com> Signed-off-by:
-
Peter Hurley authored
When echoes cannot be flushed to output (usually because the tty has no more write room) and L_ECHO is subsequently turned off, then when L_ECHO is turned back on, stale echoes are output. Output completed echoes regardless of the L_ECHO setting: 1. before normal writes to that tty 2. if the tty was stopped by soft flow control and is being restarted Reported-by:Mikulas Patocka <mpatocka@redhat.com> Cc: <stable@vger.kernel.org> # 3.13.x Signed-off-by:
Peter Hurley <peter@hurleysoftware.com> Signed-off-by:
-
Qipan Li authored
commit 8b9ade9f coming from Viresh Kumar "tty: serial: sirfsoc: drop uart_port->lock before calling tty_flip_buffer_push()" broke sirfsoc uart driver by knic: [ 5.129122] BUG: spinlock already unlocked on CPU#0, ip6tables/1331 [ 5.132554] lock: sirfsoc_uart_ports+0x4/0x8a0, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1 [ 5.141651] CPU: 0 PID: 1331 Comm: ip6tables Tainted: G W O 3.10.16 #3 [ 5.148866] [<c0013528>] (unwind_backtrace+0x0/0xe0) from [<c0010e70>] (show_stack+0x10/0x14) [ 5.157362] [<c0010e70>] (show_stack+0x10/0x14) from [<c01a5e68>] (do_raw_spin_unlock+0x40/0xc8) [ 5.166125] [<c01a5e68>] (do_raw_spin_unlock+0x40/0xc8) from [<c03ff8b4>] (_raw_spin_unlock+0x8/0x40) [ 5.175322] [<c03ff8b4>] (_raw_spin_unlock+0x8/0x40) from [<c0203fcc>] (sirfsoc_uart_pio_rx_chars+0xa4/0xc0) [ 5.185120] [<c0203fcc>] (sirfsoc_uart_pio_rx_chars+0xa4/0xc0) from [<c0204fb8>] (sirfsoc_rx_tmo_process_tl+0xdc/0x1e0) [ 5.195875] [<c0204fb8>] (sirfsoc_rx_tmo_process_tl+0xdc/0x1e0) from [<c0024b50>] (tasklet_action+0x8c/0xec) [ 5.205673] [<c0024b50>] (tasklet_action+0x8c/0xec) from [<c00242a8>] (__do_softirq+0xec/0x1d4) [ 5.214347] [<c00242a8>] (__do_softirq+0xec/0x1d4) from [<c0024428>] (do_softirq+0x48/0x54) [ 5.222674] [<c0024428>] (do_softirq+0x48/0x54) from [<c0024690>] (irq_exit+0x74/0xc0) [ 5.230573] [<c0024690>] (irq_exit+0x74/0xc0) from [<c000e1e8>] (handle_IRQ+0x6c/0x90) [ 5.238465] [<c000e1e8>] (handle_IRQ+0x6c/0x90) from [<c000d500>] (__irq_svc+0x40/0x70) [ 5.246446] [<c000d500>] (__irq_svc+0x40/0x70) from [<c0092e7c>] (mark_page_accessed+0xc/0x68) [ 5.255034] [<c0092e7c>] (mark_page_accessed+0xc/0x68) from [<c00a2a4c>] (unmap_single_vma+0x3bc/0x550) [ 5.264402] [<c00a2a4c>] (unmap_single_vma+0x3bc/0x550) from [<c00a3b4c>] (unmap_vmas+0x44/0x54) [ 5.273164] [<c00a3b4c>] (unmap_vmas+0x44/0x54) from [<c00a81a8>] (exit_mmap+0xc4/0x1e0) [ 5.281233] [<c00a81a8>] (exit_mmap+0xc4/0x1e0) from [<c001bb78>] (mmput+0x3c/0xdc) [ 5.288868] [<c001bb78>] (mmput+0x3c/0xdc) from [<c0021b0c>] (do_exit+0x30c/0x828) [ 5.296413] [<c0021b0c>] (do_exit+0x30c/0x828) from [<c0022dac>] (do_group_exit+0x4c/0xb0) [ 5.304653] [<c0022dac>] (do_group_exit+0x4c/0xb0) from [<c0022e20>] (__wake_up_parent+0x0/0x18) Root cause: the commit dropped uart_port->lock before calling tty_flip_buffer_push(), but in sirfsoc-uart, sirfsoc_uart_pio_rx_chars() can be called by sirfsoc_rx_tmo_process_tl(). here uart_port->lock has not been taken yet. so that caused unpaired lock/unlock. Solution: This patch is doing a quick fix for that, it adds spin_lock/unlock(&port->lock) protect to sirfsoc_uart_pio_rx_chars() in sirfsoc_rx_tmo_process_tl() to keep spin_lock/unlock in pair. Signed-off-by:
-
Dmitry Eremin-Solenikov authored
Aparently 9865 uses standard BAR encoding scheme (unlike 99xx cards). Current pci_netmos_9900_setup() uses wrong BAR indices for the 9865 PCI device, function 2. Using standard BAR indices makes all 6 ports work for me. Thus disable the NetMos 9900 quirk for NetMos 9865 pci device. For the reference, here is the relevant part of lspci for my device: 02:07.0 Serial controller: MosChip Semiconductor Technology Ltd. PCI 9865 Multi-I/O Controller (prog-if 02 [16550]) Subsystem: Device a000:1000 Flags: bus master, medium devsel, latency 32, IRQ 17 I/O ports at ac00 [size=8] Memory at fcfff000 (32-bit, non-prefetchable) [size=4K] Memory at fcffe000 (32-bit, non-prefetchable) [size=4K] Capabilities: [48] Power Management version 2 Kernel driver in use: serial 02:07.1 Serial controller: MosChip Semiconductor Technology Ltd. PCI 9865 Multi-I/O Controller (prog-if 02 [16550]) Subsystem: Device a000:1000 Flags: bus master, medium devsel, latency 32, IRQ 18 I/O ports at a800 [size=8] Memory at fcffd000 (32-bit, non-prefetchable) [size=4K] Memory at fcffc000 (32-bit, non-prefetchable) [size=4K] Capabilities: [48] Power Management version 2 Kernel driver in use: serial 02:07.2 Communication controller: MosChip Semiconductor Technology Ltd. PCI 9865 Multi-I/O Controller Subsystem: Device a000:3004 Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at a400 [size=8] I/O ports at a000 [size=8] I/O ports at 9c00 [size=8] I/O ports at 9800 [size=8] Memory at fcffb000 (32-bit, non-prefetchable) [size=4K] Capabilities: [48] Power Management version 2 Kernel driver in use: serial Signed-off-by:
Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Signed-off-by:
-
Peter Hurley authored
Commit eafbe67f, n_tty: Refactor input_available_p() by call site broke poll() when TIME_CHAR(tty) and MIN_CHAR(tty) are both 0. When TIME_CHAR and MIN_CHAR are both 0, input is available if the read_cnt is 1 (not 0). Reported-by:
Eric Dumazet <edumazet@google.com> Tested-by:
Stephane Eranian <eranian@google.com> Tested-by:
David Ahern <dsahern@gmail.com> Tested-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Michael Grzeschik authored
If the gpio is not yet available we better also defer the probing in the rs485 case. Signed-off-by:
Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Mika Westerberg authored
CONFIG_PM will be set if either or both CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME is set. Compiling the driver with !CONFIG_PM_SLEEP causes following compilation warnings: drivers/tty/serial/8250/8250_dw.c:404:12: warning: ‘dw8250_suspend’ defined but not used [-Wunused-function] drivers/tty/serial/8250/8250_dw.c:413:12: warning: ‘dw8250_resume’ defined but not used [-Wunused-function] Fix this by using CONFIG_PM_SLEEP instead. Signed-off-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by:
-
Markus Pargmann authored
Currently the info message about a missing wakeirq for uart is printed every time the serial driver's startup function is called. This happens multiple times and not just once. This can cause lots of extra messages at boot time, slowing things down. It is caused by commit 2a0b965c (serial: omap: Add support for optional wake-up) which was applied for v3.13-rc1. This patch moves the infomessage to the probe function to display it only once. Reported-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
Markus Pargmann <mpa@pengutronix.de> Acked-by:
-
Alexander Shiyan authored
This patch adds the devicetree documentation for the Maxim MAX310X UARTs. Signed-off-by:
-
Alexander Shiyan authored
This patch adds devicetree support for the MAX310X serial driver. Signed-off-by:
-
Alexander Shiyan authored
This patch removes some unused definitions from driver code and sort #includes alphabetically. Signed-off-by:
-
Alexander Shiyan authored
This patch adds support for RS-485 (TIOCSRS485/TIOCGRS485) IOCTLs. As a result this patch eliminate private driver header. Signed-off-by:
-
Alexander Shiyan authored
Signed-off-by:
-
Alexander Shiyan authored
Always register GPIOs and use dynamic GPIO ID assignment. This is no much worth if GPIOs is not used, but helps remove private driver header and add DT support in the future. Additionally, patch adds missing uart_unregister_driver() call if probe() fails. Signed-off-by:
-
Alexander Shiyan authored
This patch removes "frequency" parameter from MAX310X platform_data and uses CLK API for getting clock. Clock type (XTAL/OSC) is determined by clk name. Signed-off-by:
-
Alexander Shiyan authored
Patch move all SPI-dependent stuff in one place. This include move PM-function definitions out of CONFIG_SPI_MASTER and move regmap initialization out of common probe into CONFIG_SPI_MASTER which may help to add I2C support in the future for this driver. Signed-off-by:
-
Baruch Siach authored
Since 93abe8e4 (clk: add non CONFIG_HAVE_CLK routines) code using clk.h like this driver needs not depend on HAVE_CLK. Signed-off-by:
Baruch Siach <baruch@tkos.co.il> Acked-by:
Simon Horman <horms+renesas@verge.net.au> Signed-off-by:
-
Alexander Shiyan authored
This patch removes excess IRQ checks at driver probe(). IRQ validation is already provided by request_threaded_irq(). Signed-off-by:
-
Alexander Shiyan authored
This patch replaces loopback mode support from platform data to dynamic setup with TIOCMSET ioctl. Signed-off-by:
-
Alexander Shiyan authored
Serial core calls set_termios() after port startup, so there are no reason to setup port twice. Signed-off-by:
-
Alexander Shiyan authored
These callbacks were previously used for the IC power initialization. If this initialization will be needed in the future, it should be implemented with the regulator API. Signed-off-by:
-
Alexander Shiyan authored
This patch provide more precisely setup of baud rate generator. If the result of division has a remainder, we use the multiplier for the base frequency. Additionally, we report result baud rate back to serial core. Signed-off-by:
-
Alexander Shiyan authored
Signed-off-by:
-
Laurent Pinchart authored
Hardware supported by the driver is only found on SUPERH or ARCH_SHMOBILE platforms. Restrict non-COMPILE_TEST compilation to them. Cc: linux-serial@vger.kernel.org Signed-off-by:
Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by:
-
Laurent Pinchart authored
Remove the -generic suffix from the compatible string in the serial port DT bindings example. Cc: devicetree@vger.kernel.org Signed-off-by:
-
Jingoo Han authored
Add CONFIG_DEBUG_FS to 'char name' in order to fix the following build warning, because 'char name' is used only when CONFIG_DEBUG_FS is enabled. drivers/tty/serial/pch_uart.c:1765:7: warning: unused variable 'name' [-Wunused-variable] Signed-off-by:
Jingoo Han <jg1.han@samsung.com> Signed-off-by:
-
Jingoo Han authored
Fix the following compile warning about cast to pointer from integer of different size. drivers/tty/serial/sh-sci.c:2021:19: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast] Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Markus Pargmann authored
Currently the info message about a missing wakeirq for uart is printed every time the serial driver's startup function is called. This happens multiple times and not just once. This patch moves the infomessage to the probe function to display it only once. Acked-by:
-
- 12 Feb, 2014 1 commit
-
-
Stephen Boyd authored
Implement the polling functionality for the MSM serial driver. This allows us to use KGDB on this hardware. Cc: David Brown <davidb@codeaurora.org> Signed-off-by:
Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
-
- 10 Feb, 2014 2 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-securityLinus Torvalds authored
Pull SELinux fixes from James Morris. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: SELinux: Fix kernel BUG on empty security contexts. selinux: add SOCK_DIAG_BY_FAMILY to the list of netlink message types
-
