Both display controllers are in their own power partition. Currently the
driver relies on the assumption that these partitions are on (which is
the hardware default). However some bootloaders may disable them, so the
driver must make sure to turn them back on to avoid hangs.
Signed-off-by: Thierry Reding <treding@nvidia.com>

During calibration, sets the "internal reference level for drive pull-
down" to the value specified in the Tegra TRM.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Include the clock lanes when calibrating the MIPI PHY on Tegra124
compatible devices.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
[treding@nvidia.com: bikeshedding]
Signed-off-by: Thierry Reding <treding@nvidia.com>

By paving the CTRL reg value, the current code changes MIPI_CAL_PRESCALE
("Auto-cal calibration step prescale") from 1us to 0.1us (val=0). In the
description for PHY's noise filter (MIPI_CAL_NOISE_FLT), the TRM states
that if the value of the prescale is 0 (or 0.1us), the filter should be
set between 2-5. However, the current code sets it to 0.

For now, let's keep the prescale and filter values as-is, which is most
likely the power-on-reset values of 0x2 and 0xa, respectively.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>

On 64-bit platforms an unsigned long would be 64 bit and cause
unnecessary casting when being passed to writel() or returned from
readl(). Make register values 32 bits wide to avoid that.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Use the u32 type for the offset in the host1x_job_gather structure for
consistentcy with other structures. Negative offsets don't make sense in
this context.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Consistently use a format of %pad+%#x to print address/offset in debug
messages.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Signed-off-by: Thierry Reding <treding@nvidia.com>

This reduces the amount of casting that needs to be done to get rid of
annoying warnings on 64-bit builds.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Rather than cast to a u32 use the struct host1x_bo pointers directly.
This avoid annoying warnings for 64-bit builds.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The introduction of the COMPILE_TEST dependency in commit 158b50ae
(drm/tegra: Increase compile test coverage) removes the dependency on
COMMON_CLK (implicitly selected via ARCH_TEGRA, ARCH_MULTI_V7 and
ARCH_MULTIPLATFORM).
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>

struct mipi_dsi_msg is a read-only structure, drivers should never need
to modify it. Make this explicit by making all references to the struct
const.
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Currently the mipi_dsi_dcs_write() function requires the DCS command
byte to be embedded within the write buffer whereas mipi_dsi_dcs_read()
has a separate parameter. Make them more symmetrical by adding an extra
command parameter to mipi_dsi_dcs_write().

The S6E8AA0 driver relies on the old asymmetric API and there's concern
that moving to the new API may be less efficient. Provide a new function
with the old semantics for those cases and make the S6E8AA0 driver use
it instead.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>

A common pattern is starting to emerge for higher level transfer
helpers. Create a new helper that encapsulates this pattern and avoids
code duplication.
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>

This commit introduces a new function, mipi_dsi_create_packet(), which
converts from a MIPI DSI message to a MIPI DSI packet. The MIPI DSI
packet is as close to the protocol described in the DSI specification as
possible and useful in drivers that need to write a DSI packet into a
FIFO to send a message off to the peripheral.
Suggested-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Add two helpers, mipi_dsi_packet_format_is_{short,long}(), that help in
determining the format of a packet.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The %* format specifier expects an integer, which works fine with size_t
arguments on 32-bit because the types match. However on 64-bit, size_t
is typedef'd to unsigned long and will cause a build warning.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The %* format specifier expects an integer, which works fine with size_t
arguments on 32-bit because the types match. However on 64-bit, size_t
is typedef'd to unsigned long and will cause a build warning.
Signed-off-by: Thierry Reding <treding@nvidia.com>

There are several different models of N116BGE. According to commit
0a2288c0 ("drm/panel: simple: Add Innolux N116BGE panel support"),
the video timings are for the eDP variant.

The clock and htotal values added by that patch are out of spec
according to the datasheets I have seen for the eDP N116BGE (-EA2 and
-EB2).

This patch changes the values to the "Typ" values on the datasheet.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
[tested that these timings work with the Tegra132 Norrin panel]
Signed-off-by: Thierry Reding <treding@nvidia.com>

The Hitachi TX23D38VM0CAA is a 9" WVGA TFT LCD panel and can be
supported by the simple-panel driver.

This panel is connected via LVDS and uses the data enable signal for
timing. Since HSYNC/VSYNC are ignored, the split between sync length and
porches is arbitrary, as long as the complete horizontal blanking interval
is 256 clocks, and the vertical blanking interval is 45 lines.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>

The Innolux G121I1-L01 is a 12.1" TFT LCD panel and can be supported by
the simple-panel driver.

This panel is connected via LVDS and uses the data enable signal for
timing. Since HSYNC/VSYNC are ignored, the split between sync length and
porches is arbitrary, as long as the complete horizontal blanking interval
is 160 clocks, and the vertical blanking interval is 24 lines.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Various panels were missing the .bpc field which encodes the number of
bits per color. Not every display driver relies on this value, but since
the panels can be used with any display engine it must be specified so
that if a driver knows how to differentiate based on this field it can
do so.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The AUO B116XW03 is a 11.6" HD TFT LCD panel connecting to a LVDS
interface and with an integrated LED backlight unit.

This panel is used on the Samsung Chromebook(XE303C12).
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
[treding@nvidia.com: add missing .bpc field]
Signed-off-by: Thierry Reding <treding@nvidia.com>

This patch adds support for the HannStar Display Corp. HSD070PWW1 7.0"
WXGA TFT LCD panel to the simple-panel driver. The binding documentation
is included.
This panel is connected via LVDS and uses the data enable signal for
timing. Since HSYNC/VSYNC are ignored, the split between sync length and
porches is arbitrary, as long as the complete horizontal blanking interval
is 160 clocks, and the vertical blanking interval is 23 lines.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Add the new flags argument to calls of (devm_)gpiod_get*() and remove
any direction setting code afterwards.

Currently both forms (with or without the flags argument) are valid
thanks to transitional macros in <linux/gpio/consumer.h>. These macros
will be removed once all consumers are updated and the flags argument
will become compulsary.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Add the new flags argument to calls of (devm_)gpiod_get*() and remove
any direction setting code afterwards.

Currently both forms (with or without the flags argument) are valid
thanks to transitional macros in <linux/gpio/consumer.h>. These macros
will be removed once all consumers are updated and the flags argument
will become compulsary.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Add the new flags argument to calls of (devm_)gpiod_get*() and remove
any direction setting code afterwards.

Currently both forms (with or without the flags argument) are valid
thanks to transitional macros in <linux/gpio/consumer.h>. These macros
will be removed once all consumers are updated and the flags argument
will become compulsary.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Pull ARM SoC fixes from Olof Johansson:
 "A batch of fixes that have come in during the merge window.

  Some of them are defconfig updates for things that have now landed,
  some errata additions and a few general scattered fixes.

  There's also a qcom DT update that adds support for SATA on AP148, and
  basic support for Sony Xperia Z1 and CM-QS600 platforms that seemed
  isolated enough that we could merge it even if it's late"

* tag 'arm-soc-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  MAINTAINERS: corrected bcm2835 search
  ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
  ARM: dts: Explicitly set dr_mode on exynos Peach boards
  ARM: dts: qcom: add CM-QS600 board
  ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
  ARM: dts: qcom: Add SATA support on IPQ8064/AP148
  MAINTAINERS: Update Santosh Shilimkar's email id
  ARM: sunxi_defconfig: enable CONFIG_REGULATOR
  ARM: dts: Disable smc91x on n900 until bootloader dependency is removed
  ARM: omap2plus_defconfig: Enable ARM erratum 430973 for omap3
  ARM: exynos_defconfig: enable USB gadget support
  ARM: exynos_defconfig: Enable Maxim 77693 and I2C GPIO drivers
  ARM: mm: Fix ifdef around cpu_*_do_[suspend, resume] ops
  ARM: EXYNOS: Fix build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n
  ARM: SAMSUNG: Restore Samsung PM Debug functionality
  ARM: dts: Fix pull setting in sd4_width8 pin group for exynos4x12
  ARM: exynos_defconfig: Enable SBS battery support
  ARM: exynos_defconfig: Enable Control Groups support
  ARM: exynos_defconfig: Enable Atmel maXTouch support
  ARM: exynos_defconfig: Enable MAX77802

Pull audit updates from Eric Paris:
 "So this change across a whole bunch of arches really solves one basic
  problem.  We want to audit when seccomp is killing a process.  seccomp
  hooks in before the audit syscall entry code.  audit_syscall_entry
  took as an argument the arch of the given syscall.  Since the arch is
  part of what makes a syscall number meaningful it's an important part
  of the record, but it isn't available when seccomp shoots the
  syscall...

  For most arch's we have a better way to get the arch (syscall_get_arch)
  So the solution was two fold: Implement syscall_get_arch() everywhere
  there is audit which didn't have it.  Use syscall_get_arch() in the
  seccomp audit code.  Having syscall_get_arch() everywhere meant it was
  a useless flag on the stack and we could get rid of it for the typical
  syscall entry.

  The other changes inside the audit system aren't grand, fixed some
  records that had invalid spaces.  Better locking around the task comm
  field.  Removing some dead functions and structs.  Make some things
  static.  Really minor stuff"

* git://git.infradead.org/users/eparis/audit: (31 commits)
  audit: rename audit_log_remove_rule to disambiguate for trees
  audit: cull redundancy in audit_rule_change
  audit: WARN if audit_rule_change called illegally
  audit: put rule existence check in canonical order
  next: openrisc: Fix build
  audit: get comm using lock to avoid race in string printing
  audit: remove open_arg() function that is never used
  audit: correct AUDIT_GET_FEATURE return message type
  audit: set nlmsg_len for multicast messages.
  audit: use union for audit_field values since they are mutually exclusive
  audit: invalid op= values for rules
  audit: use atomic_t to simplify audit_serial()
  kernel/audit.c: use ARRAY_SIZE instead of sizeof/sizeof[0]
  audit: reduce scope of audit_log_fcaps
  audit: reduce scope of audit_net_id
  audit: arm64: Remove the audit arch argument to audit_syscall_entry
  arm64: audit: Add audit hook in syscall_trace_enter/exit()
  audit: x86: drop arch from __audit_syscall_entry() interface
  sparc: implement is_32bit_task
  sparc: properly conditionalize use of TIF_32BIT
  ...

Merge tag 'qcom-dt-for-3.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into fixes

Merge "qcom DT changes for v3.18-3" from Kumar Gala:

Qualcomm ARM Based Device Tree Updates for v3.18-3

* Added Board support for CM-QS600 and Sony Xperia Z1 phone
* Added SATA support on IPQ8064/AP148

* tag 'qcom-dt-for-3.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
  ARM: dts: qcom: add CM-QS600 board
  ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
  ARM: dts: qcom: Add SATA support on IPQ8064/AP148

Merge tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes

Pull more fixes from Kukjin Kim:

2nd Samsung fixes for v3.18
- Explicitly set dr_mode on exynos5800-peach-pi, exynos5420-peach-pit
  and exynos5420-arndale-octa boards, because the USB dwc3 controller
  will not work properly without dr_mode as host on above boards if
  the USB host and gadget are enabled in kernel configuration both.

* tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
  ARM: dts: Explicitly set dr_mode on exynos Peach boards
Signed-off-by: Olof Johansson <olof@lixom.net>

Corrected bcm2835 maintainer info by using N: to specify any files with
bcm2835 in are directed to the proper maintainer.
Also corrected minor mispelling of ARCHITECTURE in 2 comment locations.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull ntb (non-transparent bridge) updates from Jon Mason:
 "Add support for Haswell NTB split BARs, a debugfs entry for basic
  debugging info, and some code clean-ups"

* tag 'ntb-3.18' of git://github.com/jonmason/ntb:
  ntb: Adding split BAR support for Haswell platforms
  ntb: use errata flag set via DID to implement workaround
  ntb: conslidate reading of PPD to move platform detection earlier
  ntb: move platform detection to separate function
  NTB: debugfs device entry

Pull i2c updates from Wolfram Sang:
 "Highlights from the I2C subsystem for 3.18:

   - new drivers for Axxia AM55xx, and Hisilicon hix5hd2 SoC.

   - designware driver gained AMD support, exynos gained exynos7 support

  The rest is usual driver stuff.  Hopefully no lowlights this time"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: i801: Add Device IDs for Intel Sunrise Point PCH
  i2c: hix5hd2: add i2c controller driver
  i2c-imx: Disable the clock on probe failure
  i2c: designware: Add support for AMD I2C controller
  i2c: designware: Rework probe() to get clock a bit later
  i2c: designware: Default to fast mode in case of ACPI
  i2c: axxia: Add I2C driver for AXM55xx
  i2c: exynos: add support for HSI2C module on Exynos7
  i2c: mxs: detect No Slave Ack on SELECT in PIO mode
  i2c: cros_ec: Remove EC_I2C_FLAG_10BIT
  i2c: cros-ec-tunnel: Add of match table
  i2c: rcar: remove sign-compare flaw
  i2c: ismt: Use minimum descriptor size
  i2c: imx: Add arbitration lost check
  i2c: rk3x: Remove unlikely() annotations
  i2c: rcar: check for no IRQ in rcar_i2c_irq()
  i2c: rcar: make rcar_i2c_prepare_msg() *void*
  i2c: rcar: simplify check for last message
  i2c: designware: add support of platform data to set I2C mode
  i2c: designware: add support of I2C standard mode

Pull sound fixes from Takashi Iwai:
 "Here are a collection of small fixes after 3.18 merge.

  The urgent one is the fix for kernel panics with linked PCM substream
  triggered by the recent nonatomic PCM ops support.  Other two fixes
  (emu10k1 and bebob) are stable fixes, and one easy PCI ID addition for
  a new Intel HD-audio controller"

* tag 'sound-fix-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda_intel: Add Device IDs for Intel Sunrise Point PCH
  ALSA: emu10k1: Fix deadlock in synth voice lookup
  ALSA: pcm: Fix referred substream in snd_pcm_action_group() unlock loop
  ALSA: bebob: Fix failure to detect source of clock for Terratec Phase 88

Pull second round of input updates from Dmitry Torokhov:
 "Mostly simple bug fixes, although we do have one brand new driver for
  Microchip AR1021 i2c touchscreen.

  Also there is the change to stop trying to use i8042 active
  multiplexing by default (it is still possible to activate it via
  i8042.nomux=0 on boxes that implement it)"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: xpad - add Thrustmaster as Xbox 360 controller vendor
  Input: xpad - add USB ID for Thrustmaster Ferrari 458 Racing Wheel
  Input: max77693-haptic - fix state check in imax77693_haptic_disable()
  Input: xen-kbdfront - free grant table entry in xenkbd_disconnect_backend
  Input: alps - fix v4 button press recognition
  Input: i8042 - disable active multiplexing by default
  Input: i8042 - add noloop quirk for Asus X750LN
  Input: synaptics - gate forcepad support by DMI check
  Input: Add Microchip AR1021 i2c touchscreen
  Input: cros_ec_keyb - add of match table
  Input: serio - avoid negative serio device numbers
  Input: avoid negative input device numbers
  Input: automatically set EV_ABS bit in input_set_abs_params
  Input: adp5588-keys - cancel workqueue in failure path
  Input: opencores-kbd - switch to using managed resources
  Input: evdev - fix EVIOCG{type} ioctl