- 04 Aug, 2020 7 commits
-
-
Guchun Chen authored
Once the bad page saved to eeprom reaches the configured threshold, ras recovery will be issued to notify user. v2: Fix spelling typo. Signed-off-by:
Guchun Chen <guchun.chen@amd.com> Reviewed-by:
Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com>
-
Guchun Chen authored
Once the ras recovery is issued from eeprom write itself, bad page reservation should be ignored, otherwise, recursive calling of writting to eeprom would happen. Signed-off-by:
-
Guchun Chen authored
When retrieving bad gpu tag from eeprom, GPU init should fail as the GPU needs to be retired for further check. v2: Fix spelling typo, correct the condition to detect bad gpu tag and refine error message. v3: Refine function argument name. v4: Fix missing check of returning value of i2c initialization error case. v5: Use dev_err to print PCI information in dmesg instead of DRM_ERROR. Signed-off-by: -
Guchun Chen authored
This tag will be hired for bad gpu detection in eeprom's access. Signed-off-by:
-
Guchun Chen authored
Bad page threshold value should be valid in the range between -1 and max records length of eeprom. It could determine when saved bad pages exceed threshold value, and proceed corresponding actions. v2: When using the default typical value, it should be min value between typical value and eeprom max records length. v3: drop the case of setting bad_page_cnt_threshold to be 0xFFFFFFFF, as it confuses user. Signed-off-by: -
Guchun Chen authored
bad_page_threshold could be configured to enable/disable the associated bad page retirement feature in RAS. When it's -1, ras will use typical bad page failure value to handle bad page retirement. When it's 0, disable bad page retirement, and no bad page will be recorded and saved. For other valid value, driver will use this manual value as the threshold value of totoal bad pages. v2: correct documentation of this parameter. v3: remove confused statement in documentation. Signed-off-by:
-
Mukul Joshi authored
Event bitmask is a 64-bit mask with only 1 bit set. Sending this event bitmask in KFD SMI event message is both wasteful of memory and potentially limiting to only 64 events. Instead send event index in SMI event message. Please note this change does not break the ABI for the two event types defined so far. The new index is identical to the mask used before. Signed-off-by:
Mukul Joshi <mukul.joshi@amd.com> Suggested-by:
Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by:
-
- 30 Jul, 2020 22 commits
-
-
Alex Deucher authored
This regressed some working configurations so revert it. Will fix this properly for 5.9 and backport then. This reverts commit 38e0c89a. Signed-off-by:
-
Jiansong Chen authored
Enable GFXOFF for navy_flounder. Signed-off-by:
Jiansong Chen <Jiansong.Chen@amd.com> Reviewed-by:
Likun Gao <Likun.Gao@amd.com> Signed-off-by:
-
Liu ChengZhe authored
1. For Navi12, CHIP_SIENNA_CICHLID, skip tmr load operation; 2. Check pointer before release firmware. v2: use CHIP_SIENNA_CICHLID instead v3: remove local "bool ret"; fix grammer issue v4: use my name instead of "root" v5: fix grammer issue and indent issue Signed-off-by:
Liu ChengZhe <ChengZhe.Liu@amd.com> Reviewed-by:
Luben Tuikov <luben.tuikov@amd.com> Signed-off-by:
-
Liu ChengZhe authored
Assigning false to block->status.hw overwrites PSP's previous hardware status, which causes the PSP to Resume operation after hardware init. Remove this assignment and let the PSP execute Resume operation when it is told to. v2: Remove the braces. v3: Modify the description. Signed-off-by:
-
Daniel Vetter authored
Trying to grab dma_resv_lock while in commit_tail before we've done all the code that leads to the eventual signalling of the vblank event (which can be a dma_fence) is deadlock-y. Don't do that. Here the solution is easy because just grabbing locks to read something races anyway. We don't need to bother, READ_ONCE is equivalent. And avoids the locking issue. v2: Also take into account tmz_surface boolean, plus just delete the old code. Cc: linux-media@vger.kernel.org Cc: linaro-mm-sig@lists.linaro.org Cc: linux-rdma@vger.kernel.org Cc: amd-gfx@lists.freedesktop.org Cc: intel-gfx@lists.freedesktop.org Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Christian König <christian.koenig@amd.com> Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Signed-off-by:
-
Li Heng authored
Remove casting the values returned by memory allocation function. Coccinelle emits WARNING: ./drivers/gpu/drm/amd/powerplay/hwmgr/vega20_processpptables.c:893:37-46: WARNING: casting value returned by memory allocation function to (PPTable_t *) is useless. Signed-off-by:
Li Heng <liheng40@huawei.com> Signed-off-by:
-
Peilin Ye authored
Compiler leaves a 4-byte hole near the end of `dev_info`, causing amdgpu_info_ioctl() to copy uninitialized kernel stack memory to userspace when `size` is greater than 356. In 2015 we tried to fix this issue by doing `= {};` on `dev_info`, which unfortunately does not initialize that 4-byte hole. Fix it by using memset() instead. Cc: stable@vger.kernel.org Fixes: c193fa91 ("drm/amdgpu: information leak in amdgpu_info_ioctl()") Fixes: d38ceaf9 ("drm/amdgpu: add core driver (v4)") Suggested-by:Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
Peilin Ye <yepeilin.cs@gmail.com> Signed-off-by:
-
Mazin Rezk authored
This patch fixes a race condition that causes a use-after-free during amdgpu_dm_atomic_commit_tail. This can occur when 2 non-blocking commits are requested and the second one finishes before the first. Essentially, this bug occurs when the following sequence of events happens: 1. Non-blocking commit #1 is requested w/ a new dm_state #1 and is deferred to the workqueue. 2. Non-blocking commit #2 is requested w/ a new dm_state #2 and is deferred to the workqueue. 3. Commit #2 starts before commit #1, dm_state #1 is used in the commit_tail and commit #2 completes, freeing dm_state #1. 4. Commit #1 starts after commit #2 completes, uses the freed dm_state 1 and dereferences a freelist pointer while setting the context. Since this bug has only been spotted with fast commits, this patch fixes the bug by clearing the dm_state instead of using the old dc_state for fast updates. In addition, since dm_state is only used for its dc_state and amdgpu_dm_atomic_commit_tail will retain the dc_state if none is found, removing the dm_state should not have any consequences in fast updates. This use-after-free bug has existed for a while now, but only caused a noticeable issue starting from 5.7-rc1 due to 3202fa62 ("slub: relocate freelist pointer to middle of object") moving the freelist pointer from dm_state->base (which was unused) to dm_state->context (which is dereferenced). Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=207383 Fixes: bd200d19 ("drm/amd/display: Don't replace the dc_state for fast updates") Reported-by:
Duncan <1i5t5.duncan@cox.net> Signed-off-by:
Mazin Rezk <mnrzk@protonmail.com> Reviewed-by:
Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by:
-
Jiansong Chen authored
Update GC golden setting for navy_flounder. Signed-off-by:
Tao Zhou <tao.zhou1@amd.com> Signed-off-by:
-
Jiansong Chen authored
It's in accordance with pmfw 65.5.0 for navy_flounder. Signed-off-by:
Kenneth Feng <kenneth.feng@amd.com> Signed-off-by:
-
John Clements authored
add support for umc 8.7 initialization add umc 8.7 source to makefile Reviewed-by:
John Clements <john.clements@amd.com> Signed-off-by:
-
Huang Rui authored
It doesn't expose PPTable descriptor on APU platform. So max/min temperature values cannot be got from APU platform. v2: Stoney needs to skip crit temperature as well. Signed-off-by:
Huang Rui <ray.huang@amd.com> Reviewed-by:
Kevin Wang <kevin1.wang@amd.com> Signed-off-by:
-
Aric Cyr authored
[Why] Test expects that we also read HPD_IRQ_VECTOR when checking for symbol loss as well lane status. [How] Read bytes 0x200-0x205 instead of just 0x202-0x205 Signed-off-by:
Aric Cyr <aric.cyr@amd.com> Reviewed-by:
Jun Lei <Jun.Lei@amd.com> Acked-by:
Eryk Brol <eryk.brol@amd.com> Signed-off-by:
-
Aric Cyr authored
Signed-off-by:
-
Eryk Brol authored
[Why] We need to be able to specify slice width for DSC on aconnector [How] Getting slice width parameter from debugfs entry, if it is a valid the value is set in connector's dsc preffered settings structure. Which then overwrites dsc_cfg structure's parameters if DSC is decided to be enabled. Works for both SST and MST. Signed-off-by:
Mikita Lipski <mikita.lipski@amd.com> Reviewed-by:
-
Wyatt Wood authored
[Why] Feature requires synchronization of dig, pipe, and cursor locking between driver and fw. [How] Set flag to force psr to use hw lock mgr. Signed-off-by:
Wyatt Wood <wyatt.wood@amd.com> Reviewed-by:
Anthony Koo <Anthony.Koo@amd.com> Acked-by:
-
hersen wu authored
[Why] ramp_up_dispclk_with_dpp is to change dispclk, dppclk and dprefclk according to bandwidth requirement. call stack: rv1_update_clocks --> update_clocks --> dcn10_prepare_bandwidth / dcn10_optimize_bandwidth --> prepare_bandwidth / optimize_bandwidth. before change dcn hw, prepare_bandwidth will be called first to allow enough clock, watermark for change, after end of dcn hw change, optimize_bandwidth is executed to lower clock to save power for new dcn hw settings. below is sequence of commit_planes_for_stream: step 1: prepare_bandwidth - raise clock to have enough bandwidth step 2: lock_doublebuffer_enable step 3: pipe_control_lock(true) - make dchubp register change will not take effect right way step 4: apply_ctx_for_surface - program dchubp step 5: pipe_control_lock(false) - dchubp register change take effect step 6: optimize_bandwidth --> dc_post_update_surfaces_to_stream for full_date, optimize clock to save power at end of step 1, dcn clocks (dprefclk, dispclk, dppclk) may be changed for new dchubp configuration. but real dcn hub dchubps are still running with old configuration until end of step 5. this need clocks settings at step 1 should not less than that before step 1. this is checked by two conditions: 1. if (should_set_clock(safe_to_lower , new_clocks->dispclk_khz, clk_mgr_base->clks.dispclk_khz) || new_clocks->dispclk_khz == clk_mgr_base->clks.dispclk_khz) 2. request_dpp_div = new_clocks->dispclk_khz > new_clocks->dppclk_khz the second condition is based on new dchubp configuration. dppclk for new dchubp may be different from dppclk before step 1. for example, before step 1, dchubps are as below: pipe 0: recout=(0,40,1920,980) viewport=(0,0,1920,979) pipe 1: recout=(0,0,1920,1080) viewport=(0,0,1920,1080) for dppclk for pipe0 need dppclk = dispclk new dchubp pipe split configuration: pipe 0: recout=(0,0,960,1080) viewport=(0,0,960,1080) pipe 1: recout=(960,0,960,1080) viewport=(960,0,960,1080) dppclk only needs dppclk = dispclk /2. dispclk, dppclk are not lock by otg master lock. they take effect after step 1. during this transition, dispclk are the same, but dppclk is changed to half of previous clock for old dchubp configuration between step 1 and step 6. This may cause p-state warning intermittently. [How] for new_clocks->dispclk_khz == clk_mgr_base->clks.dispclk_khz, we need make sure dppclk are not changed to less between step 1 and 6. for new_clocks->dispclk_khz > clk_mgr_base->clks.dispclk_khz, new display clock is raised, but we do not know ratio of new_clocks->dispclk_khz and clk_mgr_base->clks.dispclk_khz, new_clocks->dispclk_khz /2 does not guarantee equal or higher than old dppclk. we could ignore power saving different between dppclk = displck and dppclk = dispclk / 2 between step 1 and step 6. as long as safe_to_lower = false, set dpclk = dispclk to simplify condition check. CC: Stable <stable@vger.kernel.org> Signed-off-by:
Hersen Wu <hersenxs.wu@amd.com> Reviewed-by:
-
Anthony Koo authored
Signed-off-by:
-
Eryk Brol authored
[Why] Need a mechanism to force enable DSC on any connector [How] Debugfs entry overwrites newly added connector's dsc preffered settings structure and sets dsc_clock_en flag on it. During the attomic commit, depending if connector is SST or MST, we will enable DSC manually by overwriting stream's DSC flag. Signed-off-by:
-
Reza Amini authored
[Why] Each asic can optimize best based on its capabilities [How] Optimizing timing for a new pixel clock Signed-off-by:
Reza Amini <Reza.Amini@amd.com> Reviewed-by:
-
Jun Lei authored
[Why] Programming DCN is explicitly forbidden during idle optimzations allowed state. Existing implemenation relies on OS/DM, which is not robust. Instead DC should sequence this. Note that DC will not re-enter idle optimized state on its own, it is only responsible for catching out of sequence calls. It is still DM responsibility to sequence appropriate for optimized power, but this change removes the requirement for DM to cover the .1% case. [How] - elevate updates during idle optimized state to full updates - disable idle power optimizations prior to programming Signed-off-by:
-
Stylon Wang authored
[Why] Setting abm level does not correctly update CRTC state. As a result no surface update is added to dc stream state and triggers warning. [How] Correctly update CRTC state when setting abm level property. CC: Stable <stable@vger.kernel.org> Signed-off-by:
Stylon Wang <stylon.wang@amd.com> Reviewed-by:
-
- 28 Jul, 2020 3 commits
-
-
Alex Deucher authored
Ported from radeon. Acked-by:
-
Mauro Rossi authored
[Why] All DCE6 specific code changes are guarded by CONFIG_DRM_AMD_DC_SI Kconfig option [How] (v1) CONFIG_DRM_AMD_DC_SI configuration option is added, default setting is disabled (v2) Hainan is not supported, description updated accordingly Tested with HD7750 (Cape Verde) and HD7950 (Tahiti) Reviewed-by:
Mauro Rossi <issor.oruam@gmail.com> Signed-off-by:
-
Mauro Rossi authored
[Why] amdgpu_device.c requires changes for SI chipsets support si.c require changes for Display Manager IP block enabling [How] amdgpu_device.c: add SI families in amdgpu_device_asic_has_dc_support() si.c: changes in si_set_ip_blocks() for Display Manager IP blocks enablement (v1) NOTE: As per Kaveri and older amdgpu.dc=1 kernel cmdline is required (v2) fix for bc011f9350 ("drm/amdgpu: Change SI/CI gfx/sdma/smu init sequence") remove CHIP_HAINAN support since it does not have physical DCE6 module Reviewed-by:
-
- 27 Jul, 2020 8 commits
-
-
Mauro Rossi authored
[Why] DCE6 chipsets do not support HW rotation [How] rotation property is created for Bonaire and later Reviewed-by:
-
Mauro Rossi authored
[Why] With all DCE6 specific macros, register, masks in place dce60_resource.c may use them and become independent from DCE8 headers [How] (v1) Changelog: - use DCE6 headers for registers and masks, remove the DC8 headers - remove 7th Display Controller/Encoder register instances (DCE6 has only 6) - use DCE6 specific watermark programming registers (DPG_PIPE_ARBITRATION_CONTROL3) - use DCE6 specific input pixel processing registers shift/mask - use DCE6 specific transform registers shift/mask - use DCE6 specific link encoder registers shift/mask - use DCE6 specific output pixel processing registers shift/mask - use DCE6 specific audio registers shift/mask - use DCE6 specific dmcu registers shift/mask - use DCE6 specific hwseq registers shift/mask - use DCE6 specific mem input registers shift/mask (v2) Changelog: - use DCE6 ad hoc dce60_mem_input_construct() function - use DCE6 ad hoc dce60_transform_construct() function (v3) Changelog: - use DCE6 ad hoc dce60_ipp_construct() function (v4) Changelog: - use DCE6 ad hoc dce60_link_encoder_construct() function (v5) Changelog: - use DCE6 ad hoc dce60_opp_construct() function (v6) Changelog: - use DCE6 ad hoc dce60_audio_create() function Reviewed-by:
-
Mauro Rossi authored
[Why] DCE6 has CRTC_PREFETCH_EN bit in CRTC_CONTROL register DCE6 has no CRTC_LEGACY_REQUESTOR_EN bit in CRTC_START_LINE_CONTROL register DCE6 has no CRTC_CRC_CNTL register [How] Modify dce60_timing_generator_enable_advanced_request() function Add dce60_configure_crc() function and dce60_is_tg_enabled() kept as static Use dce60_configure_crc() function in dce60_tg_funcs v2: remove unused variable (Alex) Reviewed-by:
-
Mauro Rossi authored
[Why] kernel WARNING due to use of .cursor_lock = dce_pipe_control_lock inherited by dce110 [How] DCE6 set .cursor_lock = dce60_pipe_control_lock Reviewed-by:
-
Mauro Rossi authored
[Why] DCE6 has no bottom_pipe and no Blender HW DCE6 needs 'blank_target' set to false in order to turn on the display DCE6 has a specific dce60_pipe_control_lock() fuction that is a no op [How] Add DCE6 specific functions with needed private dce60_* dependent fuctions Comment DCE6 specific CTRC program visibility implementation Fix a typo in the initial header includes comment 's/DCE8/DCE6/g' Use dce60_apply_ctx_for_surface() in dce60_hw_sequencer_construct Use dce60_pipe_control_lock() in dce60_hw_sequencer_construct v2: add missing return type (Alex) Reviewed-by:
-
Mauro Rossi authored
[Why] DCE6 has specific SCL_HORZ_FILTER_INIT_{LUMA_RGB,CHROMA} registers In DCE6 h_init_luma and h_init_chroma initialization is required Some DCE6 specific SCL_{HORZ,VERT}_FILTER_CONTROL masks were not listed [How] Add the registers and masks in dce_transform.h Add DCE6 specific struct sclh_ratios_inits in dce_transform.h Add dce60_calculate_inits() function Add dce60_program_scl_ratios_inits() function Fix dce60_transform_set_scaler() function v2: remove unused variable (Alex) Reviewed-by: -
Mauro Rossi authored
[Why] DCE6 has no SCL_MODE and no SCL_{HORZ,VERT}_FILTER_INIT registers DCE6 has no SCL_BOUNDARY_MODE bit in SCL_CONTROL register DCE6 has Line Buffer programming registers (DC_LB_MEMORY_SPLIT,DC_LB_MEM_SIZE) DCE6 DATA_FORMAT register has only INTERLEAVE_EN bit DCE6 has no Out Clamp Control programming registers (OUT_CLAMP_CONTROL_*) [How] Add DCE6 specific macros definitions for XFM registers and masks Add DCE6 specific registers to dce_transform_registers struct Add DCE6 specific masks to dce_transform_mask struct DCE6 XFM macros/structs changes will avoid buiding errors when using DCE6 headers Add dce60_setup_scaling_configuration() w/o missing Scaling registers/bit programming Add dce60_transform_set_scaler() using DCE6 Line Buffer programming registers Add dce60_program_bit_depth_reduction() w/o Out Clamp Control programming Add dce60_transform_set_pixel_storage_depth() use dce60_program_bit_depth_reduction() Use dce60_transform_set_scaler() in dce60_transform_funcs Use dce60_transform_set_pixel_storage_depth() in dce60_transform_funcs Add DCE6 specific dce60_transform_construct Reviewed-by: -
Mauro Rossi authored
[Why] DCE6 has no FMT_TRUNCATE_MODE bit in FMT_BIT_DEPTH_CONTROL register DCE6 has no FMT_CLAMP_COMPONENT_{R,G,B} registers DCE6 has no FMT_SUBSAMPLING_{MODE,ORDER} bits in FMT_CONTROL register [How] Add DCE6 specific macros definitions for OPP registers and masks DCE6 OPP macros will avoid buiding errors when using DCE6 headers Add dce60_set_truncation() w/o FMT_TRUNCATE_MODE bit programming Add dce60_opp_set_clamping() w/o Format Clamp Component programming Add dce60_opp_program_fmt() w/o Format Subsampling bits programming Add dce60_opp_program_bit_depth_reduction() with dce60_set_truncation Use dce60_opp_program_fmt() in dce60_opp_funcs Use dce60_opp_program_bit_depth_reduction() in dce60_opp_funcs Add DCE6 specific dce60_opp_construct Reviewed-by:
-
