- 07 Jun, 2016 1 commit
-
-
Rajkumar Manoharan authored
commit 8a75fc54 upstream. commit 166de3f1 ("ath10k: remove supported chain mask") had revealed an issue on monitor mode. Configuring NSS upon monitor interface creation is causing target assert in all qca9888x and qca6174 firmware. Firmware assert issue can be reproduced by below sequence even after reverting commit 166de3f1 ("ath10k: remove supported chain mask"). ip link set wlan0 down iw wlan0 set type monitor iw phy0 set antenna 7 ip link set wlan0 up This issue is originally reported on qca9888 with 10.1 firmware. Fixes: 5572a95b ("ath10k: apply chainmask settings to vdev on creation") Reported-by:
Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by:
Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by:
Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
- 27 May, 2016 1 commit
-
-
Kamal Mostafa authored
Signed-off-by:
-
- 24 May, 2016 38 commits
-
-
Mikko Rapeli authored
[ Upstream commit 4a91cb61 ] glibc's net/if.h contains copies of definitions from linux/if.h and these conflict and cause build failures if both files are included by application source code. Changes in uapi headers, which fixed header file dependencies to include linux/if.h when it was needed, e.g. commit 1ffad83d, made the net/if.h and linux/if.h incompatibilities visible as build failures for userspace applications like iproute2 and xtables-addons. This patch fixes compile errors when glibc net/if.h is included before linux/if.h: ./linux/if.h:99:21: error: redeclaration of enumerator ‘IFF_NOARP’ ./linux/if.h:98:23: error: redeclaration of enumerator ‘IFF_RUNNING’ ./linux/if.h:97:26: error: redeclaration of enumerator ‘IFF_NOTRAILERS’ ./linux/if.h:96:27: error: redeclaration of enumerator ‘IFF_POINTOPOINT’ ./linux/if.h:95:24: error: redeclaration of enumerator ‘IFF_LOOPBACK’ ./linux/if.h:94:21: error: redeclaration of enumerator ‘IFF_DEBUG’ ./linux/if.h:93:25: error: redeclaration of enumerator ‘IFF_BROADCAST’ ./linux/if.h:92:19: error: redeclaration of enumerator ‘IFF_UP’ ./linux/if.h:252:8: error: redefinition of ‘struct ifconf’ ./linux/if.h:203:8: error: redefinition of ‘struct ifreq’ ./linux/if.h:169:8: error: redefinition of ‘struct ifmap’ ./linux/if.h:107:23: error: redeclaration of enumerator ‘IFF_DYNAMIC’ ./linux/if.h:106:25: error: redeclaration of enumerator ‘IFF_AUTOMEDIA’ ./linux/if.h:105:23: error: redeclaration of enumerator ‘IFF_PORTSEL’ ./linux/if.h:104:25: error: redeclaration of enumerator ‘IFF_MULTICAST’ ./linux/if.h:103:21: error: redeclaration of enumerator ‘IFF_SLAVE’ ./linux/if.h:102:22: error: redeclaration of enumerator ‘IFF_MASTER’ ./linux/if.h:101:24: error: redeclaration of enumerator ‘IFF_ALLMULTI’ ./linux/if.h:100:23: error: redeclaration of enumerator ‘IFF_PROMISC’ The cases where linux/if.h is included before net/if.h need a similar fix in the glibc side, or the order of include files can be changed userspace code as a workaround. This change was tested in x86 userspace on Debian unstable with scripts/headers_compile_test.sh: $ make headers_install && \ cd usr/include && ../../scripts/headers_compile_test.sh -l -k ... cc -Wall -c -nostdinc -I /usr/lib/gcc/i586-linux-gnu/5/include -I /usr/lib/gcc/i586-linux-gnu/5/include-fixed -I . -I /home/mcfrisk/src/linux-2.6/usr/headers_compile_test_include.2uX2zH -I /home/mcfrisk/src/linux-2.6/usr/headers_compile_test_include.2uX2zH/i586-linux-gnu -o /dev/null ./linux/if.h_libc_before_kernel.h PASSED libc before kernel test: ./linux/if.h Reported-by:
Jan Engelhardt <jengelh@inai.de> Reported-by:
Josh Boyer <jwboyer@fedoraproject.org> Reported-by:
Stephen Hemminger <shemming@brocade.com> Reported-by:
Waldemar Brodkorb <mail@waldemar-brodkorb.de> Cc: Gabriel Laskar <gabriel@lse.epita.fr> Signed-off-by:
Mikko Rapeli <mikko.rapeli@iki.fi> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Craig Gallek authored
[ Upstream commit d894ba18 ] With the SO_REUSEPORT socket option, it is possible to create sockets in the AF_INET and AF_INET6 domains which are bound to the same IPv4 address. This is only possible with SO_REUSEPORT and when not using IPV6_V6ONLY on the AF_INET6 sockets. Prior to the commits referenced below, an incoming IPv4 packet would always be routed to a socket of type AF_INET when this mixed-mode was used. After those changes, the same packet would be routed to the most recently bound socket (if this happened to be an AF_INET6 socket, it would have an IPv4 mapped IPv6 address). The change in behavior occurred because the recent SO_REUSEPORT optimizations short-circuit the socket scoring logic as soon as they find a match. They did not take into account the scoring logic that favors AF_INET sockets over AF_INET6 sockets in the event of a tie. To fix this problem, this patch changes the insertion order of AF_INET and AF_INET6 addresses in the TCP and UDP socket lists when the sockets have SO_REUSEPORT set. AF_INET sockets will be inserted at the head of the list and AF_INET6 sockets with SO_REUSEPORT set will always be inserted at the tail of the list. This will force AF_INET sockets to always be considered first. Fixes: e32ea7e7 ("soreuseport: fast reuseport UDP socket selection") Fixes: 125e80b88687 ("soreuseport: fast reuseport TCP socket selection") Reported-by:
Maciej Żenczykowski <maze@google.com> Signed-off-by:
Craig Gallek <kraig@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Bjørn Mork authored
[ Upstream commit c5b5343c ] We now have a positive report of another Huawei device needing this quirk: The ME906s-158 (12d1:15c1). This is an m.2 form factor modem with no obvious relationship to the E3372 (12d1:157d) we already have a quirk entry for. This is reason enough to believe the quirk might be necessary for any number of current and future Huawei devices. Applying the quirk to all Huawei devices, since it is crucial to any device affected by the firmware bug, while the impact on non-affected devices is negligible. The quirk can if necessary be disabled per-device by writing N to /sys/class/net/<iface>/cdc_ncm/ndp_to_end Reported-by:
Andreas Fett <andreas.fett@secunet.com> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Kangjie Lu authored
[ Upstream commit 79e48650 ] Stack object "dte_facilities" is allocated in x25_rx_call_request(), which is supposed to be initialized in x25_negotiate_facilities. However, 5 fields (8 bytes in total) are not initialized. This object is then copied to userland via copy_to_user, thus infoleak occurs. Signed-off-by:
Kangjie Lu <kjlu@gatech.edu> Signed-off-by:
-
Nikolay Aleksandrov authored
[ Upstream commit 31ca0458 ] get_bridge_ifindices() is used from the old "deviceless" bridge ioctl calls which aren't called with rtnl held. The comment above says that it is called with rtnl but that is not really the case. Here's a sample output from a test ASSERT_RTNL() which I put in get_bridge_ifindices and executed "brctl show": [ 957.422726] RTNL: assertion failed at net/bridge//br_ioctl.c (30) [ 957.422925] CPU: 0 PID: 1862 Comm: brctl Tainted: G W O 4.6.0-rc4+ #157 [ 957.423009] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.8.1-20150318_183358- 04/01/2014 [ 957.423009] 0000000000000000 ffff880058adfdf0 ffffffff8138dec5 0000000000000400 [ 957.423009] ffffffff81ce8380 ffff880058adfe58 ffffffffa05ead32 0000000000000001 [ 957.423009] 00007ffec1a444b0 0000000000000400 ffff880053c19130 0000000000008940 [ 957.423009] Call Trace: [ 957.423009] [<ffffffff8138dec5>] dump_stack+0x85/0xc0 [ 957.423009] [<ffffffffa05ead32>] br_ioctl_deviceless_stub+0x212/0x2e0 [bridge] [ 957.423009] [<ffffffff81515beb>] sock_ioctl+0x22b/0x290 [ 957.423009] [<ffffffff8126ba75>] do_vfs_ioctl+0x95/0x700 [ 957.423009] [<ffffffff8126c159>] SyS_ioctl+0x79/0x90 [ 957.423009] [<ffffffff8163a4c0>] entry_SYSCALL_64_fastpath+0x23/0xc1 Since it only reads bridge ifindices, we can use rcu to safely walk the net device list. Also remove the wrong rtnl comment above. Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by:
-
Ian Campbell authored
[ Upstream commit dedc58e0 ] The peer may be expecting a reply having sent a request and then done a shutdown(SHUT_WR), so tearing down the whole socket at this point seems wrong and breaks for me with a client which does a SHUT_WR. Looking at other socket family's stream_recvmsg callbacks doing a shutdown here does not seem to be the norm and removing it does not seem to have had any adverse effects that I can see. I'm using Stefan's RFC virtio transport patches, I'm unsure of the impact on the vmci transport. Signed-off-by:
Ian Campbell <ian.campbell@docker.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Stefan Hajnoczi <stefanha@redhat.com> Cc: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com> Cc: Andy King <acking@vmware.com> Cc: Dmitry Torokhov <dtor@vmware.com> Cc: Jorgen Hansen <jhansen@vmware.com> Cc: Adit Ranadive <aditr@vmware.com> Cc: netdev@vger.kernel.org Signed-off-by:
-
Kangjie Lu authored
[ Upstream commit 5f8e4474 ] The stack object “map” has a total size of 32 bytes. Its last 4 bytes are padding generated by compiler. These padding bytes are not initialized and sent out via “nla_put”. Signed-off-by:
-
Kangjie Lu authored
[ Upstream commit b8670c09 ] The stack object “info” has a total size of 12 bytes. Its last byte is padding which is not initialized and leaked via “put_cmsg”. Signed-off-by:
-
Neil Horman authored
[ Upstream commit 6071bd1a ] This was recently reported to me, and reproduced on the latest net kernel, when attempting to run netperf from a host that had a netem qdisc attached to the egress interface: [ 788.073771] ---------------------[ cut here ]--------------------------- [ 788.096716] WARNING: at net/core/dev.c:2253 skb_warn_bad_offload+0xcd/0xda() [ 788.129521] bnx2: caps=(0x00000001801949b3, 0x0000000000000000) len=2962 data_len=0 gso_size=1448 gso_type=1 ip_summed=3 [ 788.182150] Modules linked in: sch_netem kvm_amd kvm crc32_pclmul ipmi_ssif ghash_clmulni_intel sp5100_tco amd64_edac_mod aesni_intel lrw gf128mul glue_helper ablk_helper edac_mce_amd cryptd pcspkr sg edac_core hpilo ipmi_si i2c_piix4 k10temp fam15h_power hpwdt ipmi_msghandler shpchp acpi_power_meter pcc_cpufreq nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs libcrc32c sd_mod crc_t10dif crct10dif_generic mgag200 syscopyarea sysfillrect sysimgblt i2c_algo_bit drm_kms_helper ahci ata_generic pata_acpi ttm libahci crct10dif_pclmul pata_atiixp tg3 libata crct10dif_common drm crc32c_intel ptp serio_raw bnx2 r8169 hpsa pps_core i2c_core mii dm_mirror dm_region_hash dm_log dm_mod [ 788.465294] CPU: 16 PID: 0 Comm: swapper/16 Tainted: G W ------------ 3.10.0-327.el7.x86_64 #1 [ 788.511521] Hardware name: HP ProLiant DL385p Gen8, BIOS A28 12/17/2012 [ 788.542260] ffff880437c036b8 f7afc56532a53db9 ffff880437c03670 ffffffff816351f1 [ 788.576332] ffff880437c036a8 ffffffff8107b200 ffff880633e74200 ffff880231674000 [ 788.611943] 0000000000000001 0000000000000003 0000000000000000 ffff880437c03710 [ 788.647241] Call Trace: [ 788.658817] <IRQ> [<ffffffff816351f1>] dump_stack+0x19/0x1b [ 788.686193] [<ffffffff8107b200>] warn_slowpath_common+0x70/0xb0 [ 788.713803] [<ffffffff8107b29c>] warn_slowpath_fmt+0x5c/0x80 [ 788.741314] [<ffffffff812f92f3>] ? ___ratelimit+0x93/0x100 [ 788.767018] [<ffffffff81637f49>] skb_warn_bad_offload+0xcd/0xda [ 788.796117] [<ffffffff8152950c>] skb_checksum_help+0x17c/0x190 [ 788.823392] [<ffffffffa01463a1>] netem_enqueue+0x741/0x7c0 [sch_netem] [ 788.854487] [<ffffffff8152cb58>] dev_queue_xmit+0x2a8/0x570 [ 788.880870] [<ffffffff8156ae1d>] ip_finish_output+0x53d/0x7d0 ... The problem occurs because netem is not prepared to handle GSO packets (as it uses skb_checksum_help in its enqueue path, which cannot manipulate these frames). The solution I think is to simply segment the skb in a simmilar fashion to the way we do in __dev_queue_xmit (via validate_xmit_skb), with some minor changes. When we decide to corrupt an skb, if the frame is GSO, we segment it, corrupt the first segment, and enqueue the remaining ones. tested successfully by myself on the latest net kernel, to which this applies Signed-off-by:
Neil Horman <nhorman@tuxdriver.com> CC: Jamal Hadi Salim <jhs@mojatatu.com> CC: "David S. Miller" <davem@davemloft.net> CC: netem@lists.linux-foundation.org CC: eric.dumazet@gmail.com CC: stephen@networkplumber.org Acked-by:
-
WANG Cong authored
[ Upstream commit bdf17661 ] Similarly, we need to update backlog too when we update qlen. Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
WANG Cong authored
[ Upstream commit 431e3a8e ] We saw qlen!=0 but backlog==0 on our production machine: qdisc htb 1: dev eth0 root refcnt 2 r2q 10 default 1 direct_packets_stat 0 ver 3.17 Sent 172680457356 bytes 222469449 pkt (dropped 0, overlimits 123575834 requeues 0) backlog 0b 72p requeues 0 The problem is we only count qlen for HTB qdisc but not backlog. We need to update backlog too when we update qlen, so that we can at least know the average packet length. Cc: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by:
Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by:
-
WANG Cong authored
[ Upstream commit 2ccccf5f ] When the bottom qdisc decides to, for example, drop some packet, it calls qdisc_tree_decrease_qlen() to update the queue length for all its ancestors, we need to update the backlog too to keep the stats on root qdisc accurate. Cc: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by:
-
WANG Cong authored
[ Upstream commit 86a7996c ] Remove nearly duplicated code and prepare for the following patch. Cc: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by:
-
Jann Horn authored
[ Upstream commit 8358b02b ] When bpf(BPF_PROG_LOAD, ...) was invoked with a BPF program whose bytecode references a non-map file descriptor as a map file descriptor, the error handling code called fdput() twice instead of once (in __bpf_map_get() and in replace_map_fd_with_map_ptr()). If the file descriptor table of the current task is shared, this causes f_count to be decremented too much, allowing the struct file to be freed while it is still in use (use-after-free). This can be exploited to gain root privileges by an unprivileged user. This bug was introduced in commit 0246e64d ("bpf: handle pseudo BPF_LD_IMM64 insn"), but is only exploitable since commit 1be7f75d ("bpf: enable non-root eBPF programs") because previously, CAP_SYS_ADMIN was required to reach the vulnerable code. (posted publicly according to request by maintainer) Signed-off-by:
Jann Horn <jannh@google.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Acked-by:
Alexei Starovoitov <ast@kernel.org> Acked-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Paolo Abeni authored
[ Upstream commit 391a2033 ] After commit fbd40ea0 ("ipv4: Don't do expensive useless work during inetdev destroy.") when deleting an interface, fib_del_ifaddr() can be executed without any primary address present on the dead interface. The above is safe, but triggers some "bug: prim == NULL" warnings. This commit avoids warning if the in_dev is dead Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
-
Daniel Borkmann authored
[ Upstream commit 9241e2df ] When __vlan_insert_tag() fails from skb_vlan_push() path due to the skb_cow_head(), we need to undo the __skb_push() in the error path as well that was done earlier to move skb->data pointer to mac header. Moreover, I noticed that when in the non-error path the __skb_pull() is done and the original offset to mac header was non-zero, we fixup from a wrong skb->data offset in the checksum complete processing. So the skb_postpush_rcsum() really needs to be done before __skb_pull() where skb->data still points to the mac header start and thus operates under the same conditions as in __vlan_insert_tag(). Fixes: 93515d53 ("net: move vlan pop/push functions into common code") Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Daniel Borkmann authored
[ Upstream commit 6b83d28a, skb_postpush_rcsum() added from commit f8ffad69 ] Replace individual implementations with the recently introduced skb_postpush_rcsum() helper. Signed-off-by:
Tom Herbert <tom@herbertland.com> Acked-by:
-
Chris Friesen authored
[ Upstream commit d6d5e999 ] For local routes that require a particular output interface we do not want to cache the result. Caching the result causes incorrect behaviour when there are multiple source addresses on the interface. The end result being that if the intended recipient is waiting on that interface for the packet he won't receive it because it will be delivered on the loopback interface and the IP_PKTINFO ipi_ifindex will be set to the loopback interface as well. This can be tested by running a program such as "dhcp_release" which attempts to inject a packet on a particular interface so that it is received by another program on the same board. The receiving process should see an IP_PKTINFO ipi_ifndex value of the source interface (e.g., eth1) instead of the loopback interface (e.g., lo). The packet will still appear on the loopback interface in tcpdump but the important aspect is that the CMSG info is correct. Sample dhcp_release command line: dhcp_release eth1 192.168.204.222 02:11:33:22:44:66 Signed-off-by:
Allain Legacy <allain.legacy@windriver.com> Signed off-by: Chris Friesen <chris.friesen@windriver.com> Reviewed-by:
Julian Anastasov <ja@ssi.bg> Signed-off-by:
-
David S. Miller authored
[ Upstream commit a36a0d40 ] In particular, make sure we check for decnet private presence for loopback devices. Signed-off-by:
-
Paolo Abeni authored
[ Upstream commit 626abd59 ] Currently, when creating or updating a route, no check is performed in both ipv4 and ipv6 code to the hoplimit value. The caller can i.e. set hoplimit to 256, and when such route will be used, packets will be sent with hoplimit/ttl equal to 0. This commit adds checks for the RTAX_HOPLIMIT value, in both ipv4 ipv6 route code, substituting any value greater than 255 with 255. This is consistent with what is currently done for ADVMSS and MTU in the ipv4 code. Signed-off-by:
-
Eric Dumazet authored
commit 10a81980 upstream. In the very unlikely case __tcp_retransmit_skb() can not use the cloning done in tcp_transmit_skb(), we need to refresh skb_mstamp before doing the copy and transmit, otherwise TCP TS val will be an exact copy of original transmit. Fixes: 7faee5c0 ("tcp: remove TCP_SKB_CB(skb)->when") Signed-off-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
-
Uwe Kleine-König authored
commit 1c021bb7 upstream. In the receive path a queue's work bit was cleared unconditionally even if fec_enet_rx_queue only read out a part of the available packets from the hardware. This resulted in not reading any packets in the next napi turn and so packets were delayed or lost. The obvious fix is to only clear a queue's bit when the queue was emptied. Fixes: 4d494cdc ("net: fec: change data structure to support multiqueue") Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by:
Lucas Stach <l.stach@pengutronix.de> Tested-by:
Fugang Duan <fugang.duan@nxp.com> Acked-by:
-
Daniel Jurgens authored
commit 82d69203 upstream. Use htons instead of unconditionally byte swapping nexthdr. On a little endian systems shifting the byte is correct behavior, but it results in incorrect csums on big endian architectures. Fixes: f8c6455b ('net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE') Signed-off-by:
Daniel Jurgens <danielj@mellanox.com> Reviewed-by:
Carol Soto <clsoto@us.ibm.com> Tested-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
Linus Lüssing authored
commit 856ce5d0 upstream. With the newly introduced helper functions the skb pulling is hidden in the checksumming function - and undone before returning to the caller. The IGMP and MLD query parsing functions in the bridge still assumed that the skb is pointing to the beginning of the IGMP/MLD message while it is now kept at the beginning of the IPv4/6 header. If there is a querier somewhere else, then this either causes the multicast snooping to stay disabled even though it could be enabled. Or, if we have the querier enabled too, then this can create unnecessary IGMP / MLD query messages on the link. Fixing this by taking the offset between IP and IGMP/MLD header into account, too. Fixes: 9afd85c9 ("net: Export IGMP/MLD message validation code") Reported-by:
Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by:
Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by:
-
Zi Shen Lim authored
commit 98397fc5 upstream. Original implementation commit e54bcde3 ("arm64: eBPF JIT compiler") had the relevant code paths, but due to an oversight always fail jiting. As a result, we had been falling back to BPF interpreter whenever a BPF program has JMP_JSET_{X,K} instructions. With this fix, we confirm that the corresponding tests in lib/test_bpf continue to pass, and also jited. ... [ 2.784553] test_bpf: #30 JSET jited:1 188 192 197 PASS [ 2.791373] test_bpf: #31 tcpdump port 22 jited:1 325 677 625 PASS [ 2.808800] test_bpf: #32 tcpdump complex jited:1 323 731 991 PASS ... [ 3.190759] test_bpf: #237 JMP_JSET_K: if (0x3 & 0x2) return 1 jited:1 110 PASS [ 3.192524] test_bpf: #238 JMP_JSET_K: if (0x3 & 0xffffffff) return 1 jited:1 98 PASS [ 3.211014] test_bpf: #249 JMP_JSET_X: if (0x3 & 0x2) return 1 jited:1 120 PASS [ 3.212973] test_bpf: #250 JMP_JSET_X: if (0x3 & 0xffffffff) return 1 jited:1 89 PASS ... Fixes: e54bcde3 ("arm64: eBPF JIT compiler") Signed-off-by:
Zi Shen Lim <zlim.lnx@gmail.com> Acked-by:
Will Deacon <will.deacon@arm.com> Acked-by:
Yang Shi <yang.shi@linaro.org> Signed-off-by:
-
Hans de Goede authored
commit a2262e5a upstream. The minium voltage of 1800mV is a copy and paste error from the axp20x regulator info. The correct minimum voltage for the ldo_io regulators on the axp22x is 700mV. Fixes: 1b82b4e4 ("regulator: axp20x: Add support for AXP22X regulators") Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Acked-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Eric Dumazet authored
commit be0bd316 upstream. If GSO packet is segmented and its segments are properly queued, we call consume_skb() instead of kfree_skb() to be drop monitor friendly. Fixes: 3e4f8b78 ("macvtap: Perform GSO on forwarding path.") Signed-off-by:
Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by:
-
Linus Torvalds authored
commit 31b0b385 upstream. The slab name ends up being visible in the directory structure under /sys, and even if you don't have access rights to the file you can see the filenames. Just use a 64-bit counter instead of the pointer to the 'net' structure to generate a unique name. This code will go away in 4.7 when the conntrack code moves to a single kmemcache, but this is the backportable simple solution to avoiding leaking kernel pointers to user space. Fixes: 5b3501fa ("netfilter: nf_conntrack: per netns nf_conntrack_cachep") Signed-off-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
-
Junxiao Bi authored
commit c25a1e06 upstream. Commit 702e5bc6 ("ocfs2: use generic posix ACL infrastructure") refactored code to use posix_acl_create. The problem with this function is that it is not mindful of the cluster wide inode lock making it unsuitable for use with ocfs2 inode creation with ACLs. For example, when used in ocfs2_mknod, this function can cause deadlock as follows. The parent dir inode lock is taken when calling posix_acl_create -> get_acl -> ocfs2_iop_get_acl which takes the inode lock again. This can cause deadlock if there is a blocked remote lock request waiting for the lock to be downconverted. And same deadlock happened in ocfs2_reflink. This fix is to revert back using ocfs2_init_acl. Fixes: 702e5bc6 ("ocfs2: use generic posix ACL infrastructure") Signed-off-by:
Tariq Saeed <tariq.x.saeed@oracle.com> Signed-off-by:
Junxiao Bi <junxiao.bi@oracle.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Joseph Qi <joseph.qi@huawei.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Wanpeng Li authored
commit f7c17d26 upstream. ------------[ cut here ]------------ WARNING: CPU: 0 PID: 16 at kernel/workqueue.c:4559 rebind_workers+0x1c0/0x1d0 Modules linked in: CPU: 0 PID: 16 Comm: cpuhp/0 Not tainted 4.6.0-rc4+ #31 Hardware name: IBM IBM System x3550 M4 Server -[7914IUW]-/00Y8603, BIOS -[D7E128FUS-1.40]- 07/23/2013 0000000000000000 ffff881037babb58 ffffffff8139d885 0000000000000010 0000000000000000 0000000000000000 0000000000000000 ffff881037babba8 ffffffff8108505d ffff881037ba0000 000011cf3e7d6e60 0000000000000046 Call Trace: dump_stack+0x89/0xd4 __warn+0xfd/0x120 warn_slowpath_null+0x1d/0x20 rebind_workers+0x1c0/0x1d0 workqueue_cpu_up_callback+0xf5/0x1d0 notifier_call_chain+0x64/0x90 ? trace_hardirqs_on_caller+0xf2/0x220 ? notify_prepare+0x80/0x80 __raw_notifier_call_chain+0xe/0x10 __cpu_notify+0x35/0x50 notify_down_prepare+0x5e/0x80 ? notify_prepare+0x80/0x80 cpuhp_invoke_callback+0x73/0x330 ? __schedule+0x33e/0x8a0 cpuhp_down_callbacks+0x51/0xc0 cpuhp_thread_fun+0xc1/0xf0 smpboot_thread_fn+0x159/0x2a0 ? smpboot_create_threads+0x80/0x80 kthread+0xef/0x110 ? wait_for_completion+0xf0/0x120 ? schedule_tail+0x35/0xf0 ret_from_fork+0x22/0x50 ? __init_kthread_worker+0x70/0x70 ---[ end trace eb12ae47d2382d8f ]--- notify_down_prepare: attempt to take down CPU 0 failed This bug can be reproduced by below config w/ nohz_full= all cpus: CONFIG_BOOTPARAM_HOTPLUG_CPU0=y CONFIG_DEBUG_HOTPLUG_CPU0=y CONFIG_NO_HZ_FULL=y As Thomas pointed out: | If a down prepare callback fails, then DOWN_FAILED is invoked for all | callbacks which have successfully executed DOWN_PREPARE. | | But, workqueue has actually two notifiers. One which handles | UP/DOWN_FAILED/ONLINE and one which handles DOWN_PREPARE. | | Now look at the priorities of those callbacks: | | CPU_PRI_WORKQUEUE_UP = 5 | CPU_PRI_WORKQUEUE_DOWN = -5 | | So the call order on DOWN_PREPARE is: | | CB 1 | CB ... | CB workqueue_up() -> Ignores DOWN_PREPARE | CB ... | CB X ---> Fails | | So we call up to CB X with DOWN_FAILED | | CB 1 | CB ... | CB workqueue_up() -> Handles DOWN_FAILED | CB ... | CB X-1 | | So the problem is that the workqueue stuff handles DOWN_FAILED in the up | callback, while it should do it in the down callback. Which is not a good idea | either because it wants to be called early on rollback... | | Brilliant stuff, isn't it? The hotplug rework will solve this problem because | the callbacks become symetric, but for the existing mess, we need some | workaround in the workqueue code. The boot CPU handles housekeeping duty(unbound timers, workqueues, timekeeping, ...) on behalf of full dynticks CPUs. It must remain online when nohz full is enabled. There is a priority set to every notifier_blocks: workqueue_cpu_up > tick_nohz_cpu_down > workqueue_cpu_down So tick_nohz_cpu_down callback failed when down prepare cpu 0, and notifier_blocks behind tick_nohz_cpu_down will not be called any more, which leads to workers are actually not unbound. Then hotplug state machine will fallback to undo and online cpu 0 again. Workers will be rebound unconditionally even if they are not unbound and trigger the warning in this progress. This patch fix it by catching !DISASSOCIATED to avoid rebind bound workers. Cc: Tejun Heo <tj@kernel.org> Cc: Lai Jiangshan <jiangshanlai@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Frédéric Weisbecker <fweisbec@gmail.com> Suggested-by:
Lai Jiangshan <jiangshanlai@gmail.com> Signed-off-by:
Wanpeng Li <wanpeng.li@hotmail.com> Signed-off-by:
-
Steven Rostedt authored
commit 106b816c upstream. At the end of process_filter(), collapse_tree() was changed to update the parg parameter, but the reassignment after the call wasn't removed. What happens is that the "current_op" gets modified and freed and parg is assigned to the new allocated argument. But after the call to collapse_tree(), parg is assigned again to the just freed "current_op", and this causes the tool to crash. The current_op variable must also be assigned to NULL in case of error, otherwise it will cause it to be free()ed twice. Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Acked-by:
Namhyung Kim <namhyung@kernel.org> Fixes: 42d6194d ("tools lib traceevent: Refactor process_filter()") Link: http://lkml.kernel.org/r/20160511150936.678c18a1@gandalf.local.homeSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Alexander Shishkin authored
commit 9f448cd3 upstream. When the PMU driver reports a truncated AUX record, it effectively means that there is no more usable room in the event's AUX buffer (even though there may still be some room, so that perf_aux_output_begin() doesn't take action). At this point the consumer still has to be woken up and the event has to be disabled, otherwise the event will just keep spinning between perf_aux_output_begin() and perf_aux_output_end() until its context gets unscheduled. Again, for cpu-wide events this means never, so once in this condition, they will be forever losing data. Fix this by disabling the event and waking up the consumer in case of a truncated AUX record. Reported-by:
Markus Metzger <markus.t.metzger@intel.com> Signed-off-by:
Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: vince@deater.net Link: http://lkml.kernel.org/r/1462886313-13660-3-git-send-email-alexander.shishkin@linux.intel.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Alexander Shishkin authored
commit ab92b232 upstream. Currently, the PT driver always sets the PMI bit one region (page) before the STOP region so that we can wake up the consumer before we run out of room in the buffer and have to disable the event. However, we also need an interrupt in the last output region, so that we actually get to disable the event (if no more room from new data is available at that point), otherwise hardware just quietly refuses to start, but the event is scheduled in and we end up losing trace data till the event gets removed. For a cpu-wide event it is even worse since there may not be any re-scheduling at all and no chance for the ring buffer code to notice that its buffer is filled up and the event needs to be disabled (so that the consumer can re-enable it when it finishes reading the data out). In other words, all the trace data will be lost after the buffer gets filled up. This patch makes PT also generate a PMI when the last output region is full. Reported-by:
-
Andrey Ryabinin authored
commit 6d6f2833 upstream. Jim reported: UBSAN: Undefined behaviour in arch/x86/events/intel/core.c:3708:12 shift exponent 35 is too large for 32-bit type 'long unsigned int' The use of 'unsigned long' type obviously is not correct here, make it 'unsigned long long' instead. Reported-by:
Jim Cromie <jim.cromie@gmail.com> Signed-off-by:
Andrey Ryabinin <aryabinin@virtuozzo.com> Signed-off-by:
-
Takashi Iwai authored
commit 84add303 upstream. Phoenix Audio has yet another device with another id (even a different vendor id, 0556:0014) that requires the same quirk for the sample rate. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=110221Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Miklos Szeredi authored
commit 9409e22a upstream. If a file is renamed to a hardlink of itself POSIX specifies that rename(2) should do nothing and return success. This condition is checked in vfs_rename(). However it won't detect hard links on overlayfs where these are given separate inodes on the overlayfs layer. Overlayfs itself detects this condition and returns success without doing anything, but then vfs_rename() will proceed as if this was a successful rename (detach_mounts(), d_move()). The correct thing to do is to detect this condition before even calling into overlayfs. This patch does this by calling vfs_select_inode() to get the underlying inodes. Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Signed-off-by:
-
Miklos Szeredi authored
commit 54d5ca87 upstream. Signed-off-by:
-
Yura Pakhuchiy authored
commit 3231e205 upstream. Subwoofer does not work out of the box on ASUS N751/N551 laptops. This patch fixes it. Patch tested on N751 laptop. N551 part is not tested, but according to [1] and [2] this laptop requires similar changes, so I included them in the patch. 1. https://github.com/honsiorovskyi/asus-n551-hda-fix 2. https://bugs.launchpad.net/ubuntu/+source/alsa-tools/+bug/1405691 Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=117781Signed-off-by:
Yura Pakhuchiy <pakhuchiy@gmail.com> Signed-off-by:
-
