Avoid 64 bit division to fix this compile error on 32 bit:
drivers/s390/char/sclp_cmd.c:711: undefined reference to `__udivdi3'

Also move the whole arch_get_memory_phys_device function to the
memory hotplug related functions.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Check tsb validity before the tcw_get_tsb function is called.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

All TCWs need to be aligned on a 64 byte boundary or the I/O will be
rejected. For recovery requests we create fresh TCWs, so we need to
do the proper alignment here as well.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

commit 02491447 "memcg: move charges of anonymous
swap" revealed that the 1 byte and 2 byte cmpxchg is currently broken:

arch/s390/include/asm/system.h: Assembler messages:
arch/s390/include/asm/system.h:241: Error: junk at end of line: `(%r5)'
make[1]: *** [mm/page_cgroup.o] Error 1
make[1]: *** Waiting for unfinished jobs....

It turned out that commit 987bcdac ([S390] use
inline assembly contraints available with gcc 3.3.3) broke the inline assembly.
The or operands are now in constraint 3 and 4 instead of 2 and 3.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

The intermediate lowcore for CONFIG_SMP is allocated using a call to
__alloc_bootmem() with a goal of 0. That however doesn't guarantee that
the allocated piece of memory is below 2GB.
Instead we should call __alloc_bootmem_low().
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

To save the registers for all CPUs a sigp "store status" is done that
stores the registers to address absolute zero. To access storage at
absolute zero, normally the address of the prefix register of the
accessing CPU has to be used. This does not work when large pages are
active (currently only under LPAR). In order to fix that problem,
instead of memcpy memcpy_real is used, which switches to real mode
where prefixing works.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Commit 45575f5a ("ppc64 sys_ipc breakage in 2.6.34-rc2") fixed the
definition of the sys_ipc() helper, but didn't fix the prototype in
<linux/syscalls.h>
Reported-and-tested-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio: console: Check if port is valid in resize_console
  virtio: console: Generate a kobject CHANGE event on adding 'name' attribute

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (38 commits)
  ip_gre: include route header_len in max_headroom calculation
  if_tunnel.h: add missing ams/byteorder.h include
  ipv4: Don't drop redirected route cache entry unless PTMU actually expired
  net: suppress lockdep-RCU false positive in FIB trie.
  Bluetooth: Fix kernel crash on L2CAP stress tests
  Bluetooth: Convert debug files to actually use debugfs instead of sysfs
  Bluetooth: Fix potential bad memory access with sysfs files
  netfilter: ctnetlink: fix reliable event delivery if message building fails
  netlink: fix NETLINK_RECV_NO_ENOBUFS in netlink_set_err()
  NET_DMA: free skbs periodically
  netlink: fix unaligned access in nla_get_be64()
  tcp: Fix tcp_mark_head_lost() with packets == 0
  net: ipmr/ip6mr: fix potential out-of-bounds vif_table access
  KS8695: update ksp->next_rx_desc_read at the end of rx loop
  igb: Add support for 82576 ET2 Quad Port Server Adapter
  ixgbevf: Message formatting cleanups
  ixgbevf: Shorten up delay timer for watchdog task
  ixgbevf: Fix VF Stats accounting after reset
  ixgbe: Set IXGBE_RSC_CB(skb)->DMA field to zero after unmapping the address
  ixgbe: fix for real_num_tx_queues update issue
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
  edac, mce: Filter out invalid values

alloc_skb() can return NULL.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It seems clear from the surrounding code that xpermits is allowed to be
NULL here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I chased down a fail on ppc64 on 2.6.34-rc2 where an application that
uses shared memory was getting a SEGV.

Commit baed7fc9 ("Add generic sys_ipc
wrapper") changed the second argument from an unsigned long to an int.
When we call shmget the system call wrappers for sys_ipc will sign
extend second (ie the size) which truncates it.  It took a while to
track down because the call succeeds and strace shows the untruncated
size :)

The patch below changes second from an int to an unsigned long which
fixes shmget on ppc64 (and I assume s390, sparc64 and mips64).
Signed-off-by: Anton Blanchard <anton@samba.org>
--

I assume the function prototypes for the other IPC methods would cause us
to sign or zero extend second where appropriate (avoiding any security
issues). Come to think of it, the syscall wrappers for each method should do
that for us as well.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 3f6da390
(perf: Rework and fix the arch CPU-hotplug hooks) broke suspend to
RAM on my HP nx6325 (and most likely on other AMD-based boxes too)
by allowing amd_pmu_cpu_offline() to be executed for CPUs that are
going offline as part of the suspend process.  The problem is that
cpuhw->amd_nb may be NULL already, so the function should make sure
it's not NULL before accessing the object pointed to by it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Print the CPU associated with the error only when the field is valid.

Cc: <stable@kernel.org> # .32.x .33.x
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

The console port could have been hot-unplugged. Check if it is valid
before working on it.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

When the host lets us know what 'name' a port is assigned, we create the
sysfs 'name' attribute. Generate a 'change' event after this so that
udev wakes up and acts on the rules for virtio-ports (currently there's
only one rule that creates a symlink from the 'name' to the actual char
device).
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

Taking route's header_len into account, and updating gre device
needed_headroom will give better hints on upper bound of required
headroom. This is useful if the gre traffic is xfrm'ed.
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

When compiling userspace application which includes
if_tunnel.h and uses GRE_* defines you will get undefined
reference to __cpu_to_be16.

Fix this by adding missing #include <asm/byteorder.h>

Cc: stable@kernel.org
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TCP sessions over IPv4 can get stuck if routers between endpoints
do not fragment packets but implement PMTU instead, and we are using
those routers because of an ICMP redirect.

Setup is as follows

       MTU1    MTU2   MTU1
    A--------B------C------D

with MTU1 > MTU2. A and D are endpoints, B and C are routers. B and C
implement PMTU and drop packets larger than MTU2 (for example because
DF is set on all packets). TCP sessions are initiated between A and D.
There is packet loss between A and D, causing frequent TCP
retransmits.

After the number of retransmits on a TCP session reaches tcp_retries1,
tcp calls dst_negative_advice() prior to each retransmit. This results
in route cache entries for the peer to be deleted in
ipv4_negative_advice() if the Path MTU is set.

If the outstanding data on an affected TCP session is larger than
MTU2, packets sent from the endpoints will be dropped by B or C, and
ICMP NEEDFRAG will be returned. A and D receive NEEDFRAG messages and
update PMTU.

Before the next retransmit, tcp will again call dst_negative_advice(),
causing the route cache entry (with correct PMTU) to be deleted. The
retransmitted packet will be larger than MTU2, causing it to be
dropped again.

This sequence repeats until the TCP session aborts or is terminated.

Problem is fixed by removing redirected route cache entries in
ipv4_negative_advice() only if the PMTU is expired.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow fib_find_node() to be called either under rcu_read_lock()
protection or with RTNL held.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added very simple check that req buffer has enough space to
fit configuration parameters. Shall be enough to reject packets
with configuration size more than req buffer.

Crash trace below

[ 6069.659393] Unable to handle kernel paging request at virtual address 02000205
[ 6069.673034] Internal error: Oops: 805 [#1] PREEMPT
...
[ 6069.727172] PC is at l2cap_add_conf_opt+0x70/0xf0 [l2cap]
[ 6069.732604] LR is at l2cap_recv_frame+0x1350/0x2e78 [l2cap]
...
[ 6070.030303] Backtrace:
[ 6070.032806] [<bf1c2880>] (l2cap_add_conf_opt+0x0/0xf0 [l2cap]) from
[<bf1c6624>] (l2cap_recv_frame+0x1350/0x2e78 [l2cap])
[ 6070.043823]  r8:dc5d3100 r7:df2a91d6 r6:00000001 r5:df2a8000 r4:00000200
[ 6070.050659] [<bf1c52d4>] (l2cap_recv_frame+0x0/0x2e78 [l2cap]) from
[<bf1c8408>] (l2cap_recv_acldata+0x2bc/0x350 [l2cap])
[ 6070.061798] [<bf1c814c>] (l2cap_recv_acldata+0x0/0x350 [l2cap]) from
[<bf0037a4>] (hci_rx_task+0x244/0x478 [bluetooth])
[ 6070.072631]  r6:dc647700 r5:00000001 r4:df2ab740
[ 6070.077362] [<bf003560>] (hci_rx_task+0x0/0x478 [bluetooth]) from
[<c006b9fc>] (tasklet_action+0x78/0xd8)
[ 6070.087005] [<c006b984>] (tasklet_action+0x0/0xd8) from [<c006c160>]
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: Gustavo F. Padovan <gustavo@padovan.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Some of the debug files ended up wrongly in sysfs, because at that point
of time, debugfs didn't exist. Convert these files to use debugfs and
also seq_file. This patch converts all of these files at once and then
removes the exported symbol for the Bluetooth sysfs class.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When creating a high number of Bluetooth sockets (L2CAP, SCO
and RFCOMM) it is possible to scribble repeatedly on arbitrary
pages of memory. Ensure that the content of these sysfs files is
always less than one page. Even if this means truncating. The
files in question are scheduled to be moved over to debugfs in
the future anyway.

Based on initial patches from Neil Brown and Linus Torvalds
Reported-by: Neil Brown <neilb@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch fixes a bug that allows to lose events when reliable
event delivery mode is used, ie. if NETLINK_BROADCAST_SEND_ERROR
and NETLINK_RECV_NO_ENOBUFS socket options are set.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, ENOBUFS errors are reported to the socket via
netlink_set_err() even if NETLINK_RECV_NO_ENOBUFS is set. However,
that should not happen. This fixes this problem and it changes the
prototype of netlink_set_err() to return the number of sockets that
have set the NETLINK_RECV_NO_ENOBUFS socket option. This return
value is used in the next patch in these bugfix series.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Under NET_DMA, data transfer can grind to a halt when userland issues a
large read on a socket with a high RCVLOWAT (i.e., 512 KB for both).
This appears to be because the NET_DMA design queues up lots of memcpy
operations, but doesn't issue or wait for them (and thus free the
associated skbs) until it is time for tcp_recvmesg() to return.
The socket hangs when its TCP window goes to zero before enough data is
available to satisfy the read.

Periodically issue asynchronous memcpy operations, and free skbs for ones
that have completed, to prevent sockets from going into zero-window mode.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a unaligned access in nla_get_be64() that was
introduced by myself in a17c8598.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

A packet is marked as lost in case packets == 0, although nothing should be done.
This results in a too early retransmitted packet during recovery in some cases.
This small patch fixes this issue by returning immediately.
Signed-off-by: Lennart Schulte <lennart.schulte@nets.rwth-aachen.de>
Signed-off-by: Arnd Hannemann <hannemann@nets.rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

mfc_parent of cache entries is used to index into the vif_table and is
initialised from mfcctl->mfcc_parent. This can take values of to 2^16-1,
while the vif_table has only MAXVIFS (32) entries. The same problem
affects ip6mr.

Refuse invalid values to fix a potential out-of-bounds access. Unlike
the other validity checks, this is checked in ipmr_mfc_add() instead of
the setsockopt handler since its unused in the delete path and might be
uninitialized.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to adjust the next rx descriptor after each packet,
so do it only once at the end of the routine.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>

Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clean up some text output formatting.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The recovery from PF reset works better when you shorten up the delay
until the watchdog task executes.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The counters in the 82599 Virtual Function are not clear on read.  They
accumulate to the maximum value and then roll over.  They are also not
cleared when the VF executes a soft reset, so it is possible they are
non-zero when the driver loads and starts.  This has all been accounted
for in the code that keeps the stats up to date but there is one case
that is not.  When the PF driver is reset the counters in the VF are
all reset to zero.  This adds an additional accounting overhead into
the VF driver when the PF is reset under its feet.  This patch adds
additional counters that are used by the VF driver to accumulate and
save stats after a PF reset has been detected.  Prior to this patch
displaying the stats in the VF after the PF has reset would show
bogus data.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As per Simon Horman's feedback set IXGBE_RSC_CB(skb)->dma to zero
after unmapping HWRSC DMA address to avoid double freeing.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently netdev_features_change is called before fcoe tx queues
setup is done, so this patch moves calling of netdev_features_change
after tx queues setup is done in ixgbe_init_interrupt_scheme, so
that real_num_tx_queues is updated correctly on each fcoe enable
or disable.

This allows additional fcoe queues updated correctly in vlan driver
for their correct queue selection.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds RFC5082 checks for TTL on received ICMP packets.
It adds some security against spoofed ICMP packets
disrupting GTSM protected sessions.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>