- 09 Jun, 2014 1 commit
-
-
Mohammed Habibulla authored
commit 1fb4e09a upstream. Add support for the AR9462 chip T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=03 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=3007 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
Mohammed Habibulla <moch@chromium.org> Signed-off-by:
Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by:
Jiri Slaby <jslaby@suse.cz>
-
- 06 Jun, 2014 39 commits
-
-
Johan Hedberg authored
commit 9eb1fbfa upstream. Commit 1c2e0041 introduced an event handler for the encryption key refresh complete event with the intent of fixing some LE/SMP cases. However, this event is shared with BR/EDR and there we actually want to act only on the auth_complete event (which comes after the key refresh). If we do not do this we may trigger an L2CAP Connect Request too early and cause the remote side to return a security block error. Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Clemens Ladisch authored
commit 7040b6d1 upstream. The TEAC UD-H01 firmware sends wrong feedback frequency values, thus causing the PC to send the samples at a wrong rate, which results in clicks and crackles in the output. Add a workaround to detect and fix the corruption. Signed-off-by:
Clemens Ladisch <clemens@ladisch.de> [mick37@gmx.de: use sender->udh01_fb_quirk rather than ep->udh01_fb_quirk in snd_usb_handle_sync_urb()] Reported-and-tested-by:
Mick <mick37@gmx.de> Reported-and-tested-by:
Andrea Messa <andr.messa@tiscali.it> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Stanislaw Gruszka authored
commit 8834d360 upstream. When disable beaconing we clear register with beacon and newer set it back, what make we stop send beacons infinitely. Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Daniele Forsi authored
commit 6ed07d45 upstream. Signed-off-by:
Daniele Forsi <dforsi@gmail.com> Signed-off-by:
-
Victor A. Santos authored
commit f0ef5d41 upstream. Signed-off-by:
Victor A. Santos <victoraur.santos@gmail.com> Signed-off-by:
-
Daniele Forsi authored
commit df602c2d upstream. Even if the USB-to-ATAPI converter supported multiple LUNs, this driver would always detect the same physical device or media because it doesn't use srb->device->lun in any way. Tested with an Hewlett-Packard CD-Writer Plus 8200e. Signed-off-by:
-
Alan Stern authored
commit c1db30a2 upstream. Some OHCI controllers from ATI/AMD seem to have difficulty with "global" USB suspend, that is, suspending an entire USB bus without setting the suspend feature for each port connected to a device. When we try to resume the child devices, the controller gives timeout errors on the unsuspended ports, requiring resets, and can even cause ohci-hcd to hang; see http://marc.info/?l=linux-usb&m=139514332820398&w=2 and the following messages. This patch fixes the problem by adding a new quirk flag to ohci-hcd. The flag causes the ohci_rh_suspend() routine to suspend each unsuspended, enabled port before suspending the root hub. This effectively converts the "global" suspend to an ordinary root-hub suspend. There is no need to unsuspend these ports when the root hub is resumed, because the child devices will be resumed anyway in the course of a normal system resume ("global" suspend is never used for runtime PM). This patch should be applied to all stable kernels which include commit 0aa2832d (USB: use "global suspend" for system sleep on USB-2 buses) or a backported version thereof. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Peter Münster <pmlists@free.fr> Tested-by:
-
Jean-Jacques Hiblot authored
commit 886c7c42 upstream. When using dt resources retrieval (interrupts and reg properties) there is no predefined order for these resources in the platform dev resource table. Also don't expect the number of resource to be always 2. Signed-off-by:
Jean-Jacques Hiblot <jjhiblot@traphandler.com> Acked-by:
Boris BREZILLON <b.brezillon@overkiz.com> Acked-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Nikita Yushchenko authored
commit d183c819 upstream. Per reference manuals of Freescale P1020 and P2020 SoCs, USB controller present in these SoCs has bit 17 of USBx_CONTROL register marked as Reserved - there is no PHY_CLK_VALID bit there. Testing for this bit in ehci_fsl_setup_phy() behaves differently on two P1020RDB boards available here - on one board test passes and fsl-usb init succeeds, but on other board test fails, causing fsl-usb init to fail. This patch changes ehci_fsl_setup_phy() not to test PHY_CLK_VALID on controller version 1.6 that (per manual) does not have this bit. Signed-off-by:
Nikita Yushchenko <nyushchenko@dev.rtsoft.ru> Signed-off-by:
-
Atilla Filiz authored
commit b9b3a418 upstream. The driver segfaults when the kernel boots with device tree as the platform data is then not present and the pointer is deferenced without checking it is not null. This patch introduces such a check avoiding the crash. Signed-off-by:
Atilla Filiz <atilla.filiz@essensium.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Tuomas Tynkkynen authored
commit d2c834ab upstream. The value written to PLLE_AUX was incorrect due to a wrong variable being used. Without this fix SATA does not work. Signed-off-by:
Tuomas Tynkkynen <ttynkkynen@nvidia.com> Tested-by:
Mikko Perttunen <mperttunen@nvidia.com> Reviewed-by:
Thierry Reding <treding@nvidia.com> Tested-by:
Mike Turquette <mturquette@linaro.org> [mturquette@linaro.org: improved changelog] Signed-off-by:
-
Thierry Reding authored
commit cbfbbabb upstream. The version of the drm_tegra_submit structure that was merged all the way back in 3.10 contains a pad field that was originally intended to properly pad the following __u64 field. Unfortunately it seems like a different field was dropped during review that caused this padding to become unnecessary, but the pad field wasn't removed at that time. One possible side-effect of this is that since the __u64 following the pad is now no longer properly aligned, the compiler may (or may not) introduce padding itself, which results in no predictable ABI. Rectify this by removing the pad field so that all fields are again naturally aligned. Technically this is breaking existing userspace ABI, but given that there aren't any (released) userspace drivers that make use of this yet, the fallout should be minimal. Fixes: d43f81cb ("drm/tegra: Add gr2d device") Signed-off-by:
-
Leo Liu authored
commit 695daf1a upstream. Signed-off-by:
Leo Liu <leo.liu@amd.com> Signed-off-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
-
Christian König authored
commit f5d636d2 upstream. Testing the update pending bit directly after issuing an update is nonsense cause depending on the pixel clock the CRTC needs a bit of time to execute the flip even when we are in the VBLANK period. This is just a non invasive patch to solve the problem at hand, a more complete and cleaner solution should follow in the next merge window. Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=76564 v2: fix source IDs for CRTC2-6 Signed-off-by:
-
Christian König authored
commit e4518762 upstream. Some RV7xx generation hardware crashes after you raise the UVD clocks for the first time. Try to avoid this by using the lower clocks to boot these. Workaround for: https://bugzilla.kernel.org/show_bug.cgi?id=71891 v2: lower clocks on IB test as well Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Alex Deucher authored
commit 7e95cfb0 upstream. Should be 5 rather than 4. Noticed-by:
Mathias Fröhlich <Mathias.Froehlich@gmx.net> Signed-off-by:
-
Alex Deucher authored
commit 3ed9a335 upstream. Avoids a crash in certain cases when thermal irqs are generated before the display structures have been initialized. v2: fix the vblank and vrefresh helpers as well bug: https://bugzilla.kernel.org/show_bug.cgi?id=73931Signed-off-by:
-
Alex Deucher authored
commit e9a4099a upstream. Some newer PX laptops have the pci device class set to DISPLAY_OTHER rather than DISPLAY_VGA. This properly detects ATPX on those laptops. Based on a patch from: Pali Rohár <pali.rohar@gmail.com> Signed-off-by:
-
Alex Deucher authored
commit 8c79bae6 upstream. Avoid a possible segfault. Noticed-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Alex Deucher authored
commit 1ebe9280 upstream. May fix stability issues with some newer cards. v2: print out mc firmware version used and size Signed-off-by:
-
Alex Deucher authored
commit 57700ad1 upstream. Setting higher mclks seems to cause stability issues on some R7 260X boards. Disable it for now for stability until we find a proper fix. bug: https://bugs.freedesktop.org/show_bug.cgi?id=75992Signed-off-by:
-
Egbert Eich authored
commit 7f1950fb upstream. Depending on the SDVO output_flags SDVO may have multiple connectors linking to the same encoder (in intel_connector->encoder->base). Only one of those connectors should be active (ie link to the encoder thru drm_connector->encoder). If intel_connector_break_all_links() is called from intel_sanitize_crtc() we may break the crtc connection of an encoder thru an inactive connector in which case intel_connector_break_all_links() will not be called again for the active connector if this happens to come later in the list due to: if (connector->encoder->base.crtc != &crtc->base) continue; in intel_sanitize_crtc(). This will however leave the drm_connector->encoder linkage for this active connector in place. Subsequently this will cause multiple warnings in intel_connector_check_state() to trigger and the driver will eventually die in drm_encoder_crtc_ok() (because of crtc == NULL). To avoid this remove intel_connector_break_all_links() and move its code to its two calling functions: intel_sanitize_crtc() and intel_sanitize_encoder(). This allows to implement the link breaking more flexibly matching the surrounding code: ie. in intel_sanitize_crtc() we can break the crtc link separatly after the links to the encoders have been broken which avoids above problem. This regression has been introduced in: commit 24929352 Author: Daniel Vetter <daniel.vetter@ffwll.ch> Date: Mon Jul 2 20:28:59 2012 +0200 drm/i915: read out the modeset hw state at load and resume time so goes back to the very beginning of the modeset rework. v2: This patch takes care of the concernes voiced by Chris Wilson and Daniel Vetter that only breaking links if the drm_connector is linked to an encoder may miss some links. v3: move all encoder handling to encoder loop as suggested by Daniel Vetter. Signed-off-by:
Egbert Eich <eich@suse.de> Reviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Jani Nikula <jani.nikula@linux.intel.com> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Daniel Vetter authored
commit 9953599b upstream. ... our current modeset code isn't good enough yet to handle this. The scenario is: 1. BIOS sets up a cloned config with lvds+external screen on the same pipe, e.g. pipe B. 2. We read out that state for pipe B and assign the gmch_pfit state to it. 3. The initial modeset switches the lvds to pipe A but due to lack of atomic modeset we don't recompute the config of pipe B. -> both pipes now claim (in the sw pipe config structure) to use the gmch_pfit, which just won't work. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74081Tested-by:
max <manikulin@gmail.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
NeilBrown authored
commit 0f62fb22 upstream. If an md array with externally managed metadata (e.g. DDF or IMSM) is in use, then we should not set safemode==2 at shutdown because: 1/ this is ineffective: user-space need to be involved in any 'safemode' handling, 2/ The safemode management code doesn't cope with safemode==2 on external metadata and md_check_recover enters an infinite loop. Even at shutdown, an infinite-looping process can be problematic, so this could cause shutdown to hang. Signed-off-by:
NeilBrown <neilb@suse.de> Signed-off-by:
-
Viresh Kumar authored
commit 84ea7fe3 upstream. switch_hrtimer_base() calls hrtimer_check_target() which ensures that we do not migrate a timer to a remote cpu if the timer expires before the current programmed expiry time on that remote cpu. But __hrtimer_start_range_ns() calls switch_hrtimer_base() before the new expiry time is set. So the sanity check in hrtimer_check_target() is operating on stale or even uninitialized data. Update expiry time before calling switch_hrtimer_base(). [ tglx: Rewrote changelog once again ] Signed-off-by:
Viresh Kumar <viresh.kumar@linaro.org> Cc: linaro-kernel@lists.linaro.org Cc: linaro-networking@linaro.org Cc: fweisbec@gmail.com Cc: arvind.chauhan@arm.com Link: http://lkml.kernel.org/r/81999e148745fc51bbcd0615823fbab9b2e87e23.1399882253.git.viresh.kumar@linaro.orgSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Leon Ma authored
commit 012a45e3 upstream. If a cpu is idle and starts an hrtimer which is not pinned on that same cpu, the nohz code might target the timer to a different cpu. In the case that we switch the cpu base of the timer we already have a sanity check in place, which determines whether the timer is earlier than the current leftmost timer on the target cpu. In that case we enqueue the timer on the current cpu because we cannot reprogram the clock event device on the target. If the timers base is already the target CPU we do not have this sanity check in place so we enqueue the timer as the leftmost timer in the target cpus rb tree, but we cannot reprogram the clock event device on the target cpu. So the timer expires late and subsequently prevents the reprogramming of the target cpu clock event device until the previously programmed event fires or a timer with an earlier expiry time gets enqueued on the target cpu itself. Add the same target check as we have for the switch base case and start the timer on the current cpu if it would become the leftmost timer on the target. [ tglx: Rewrote subject and changelog ] Signed-off-by:
Leon Ma <xindong.ma@intel.com> Link: http://lkml.kernel.org/r/1398847391-5994-1-git-send-email-xindong.ma@intel.comSigned-off-by:
-
Stuart Hayes authored
commit 6c6c0d5a upstream. If the last hrtimer interrupt detected a hang it sets hang_detected=1 and programs the clock event device with a delay to let the system make progress. If hang_detected == 1, we prevent reprogramming of the clock event device in hrtimer_reprogram() but not in hrtimer_force_reprogram(). This can lead to the following situation: hrtimer_interrupt() hang_detected = 1; program ce device to Xms from now (hang delay) We have two timers pending: T1 expires 50ms from now T2 expires 5s from now Now T1 gets canceled, which causes hrtimer_force_reprogram() to be invoked, which in turn programs the clock event device to T2 (5 seconds from now). Any hrtimer_start after that will not reprogram the hardware due to hang_detected still being set. So we effectivly block all timers until the T2 event fires and cleans up the hang situation. Add a check for hang_detected to hrtimer_force_reprogram() which prevents the reprogramming of the hang delay in the hardware timer. The subsequent hrtimer_interrupt will resolve all outstanding issues. [ tglx: Rewrote subject and changelog and fixed up the comment in hrtimer_force_reprogram() ] Signed-off-by:
Stuart Hayes <stuart.w.hayes@gmail.com> Link: http://lkml.kernel.org/r/53602DC6.2060101@gmail.comSigned-off-by:
-
Grant Likely authored
commit 58b116bc upstream. When the kernel is built with CONFIG_PREEMPT it is possible to reach a state when all modules loaded but some driver still stuck in the deferred list and there is a need for external event to kick the deferred queue to probe these drivers. The issue has been observed on embedded systems with CONFIG_PREEMPT enabled, audio support built as modules and using nfsroot for root filesystem. The following log fragment shows such sequence when all audio modules were loaded but the sound card is not present since the machine driver has failed to probe due to missing dependency during it's probe. The board is am335x-evmsk (McASP<->tlv320aic3106 codec) with davinci-evm machine driver: ... [ 12.615118] davinci-mcasp 4803c000.mcasp: davinci_mcasp_probe: ENTER [ 12.719969] davinci_evm sound.3: davinci_evm_probe: ENTER [ 12.725753] davinci_evm sound.3: davinci_evm_probe: snd_soc_register_card [ 12.753846] davinci-mcasp 4803c000.mcasp: davinci_mcasp_probe: snd_soc_register_component [ 12.922051] davinci-mcasp 4803c000.mcasp: davinci_mcasp_probe: snd_soc_register_component DONE [ 12.950839] davinci_evm sound.3: ASoC: platform (null) not registered [ 12.957898] davinci_evm sound.3: davinci_evm_probe: snd_soc_register_card DONE (-517) [ 13.099026] davinci-mcasp 4803c000.mcasp: Kicking the deferred list [ 13.177838] davinci-mcasp 4803c000.mcasp: really_probe: probe_count = 2 [ 13.194130] davinci_evm sound.3: snd_soc_register_card failed (-517) [ 13.346755] davinci_mcasp_driver_init: LEAVE [ 13.377446] platform sound.3: Driver davinci_evm requests probe deferral [ 13.592527] platform sound.3: really_probe: probe_count = 0 In the log the machine driver enters it's probe at 12.719969 (this point it has been removed from the deferred lists). McASP driver already executing it's probing (since 12.615118). The machine driver tries to construct the sound card (12.950839) but did not found one of the components so it fails. After this McASP driver registers all the ASoC components (the machine driver still in it's probe function after it failed to construct the card) and the deferred work is prepared at 13.099026 (note that this time the machine driver is not in the lists so it is not going to be handled when the work is executing). Lastly the machine driver exit from it's probe and the core places it to the deferred list but there will be no other driver going to load and the deferred queue is not going to be kicked again - till we have external event like connecting USB stick, etc. The proposed solution is to try the deferred queue once more when the last driver is asking for deferring and we had drivers loaded while this last driver was probing. This way we can avoid drivers stuck in the deferred queue. Signed-off-by:
Grant Likely <grant.likely@linaro.org> Reviewed-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Mark Brown <broonie@kernel.org> Signed-off-by:
-
Josef Gajdusek authored
commit 3a18e139 upstream. The datasheet for EMC1413/EMC1414, which is fully compatible to EMC1403/1404 and uses the same chip identification, references revision numbers 0x01, 0x03, and 0x04. Accept the full range of revision numbers from 0x01 to 0x04 to make sure none are missed. Signed-off-by:
Josef Gajdusek <atx@atx.name> [Guenter Roeck: Updated headline and description] Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Josef Gajdusek authored
commit 17c048fc upstream. Attempts to set the hysteresis value to a temperature below the target limit fails with "write error: Numerical result out of range" due to an inverted comparison. Signed-off-by:
Jean Delvare <jdelvare@suse.de> [Guenter Roeck: Updated headline and description] Signed-off-by:
-
Leon Yu authored
commit 754320d6 upstream. iovec should be reclaimed whenever caller of rw_copy_check_uvector() returns, but it doesn't hold when failure happens right after aio_setup_vectored_rw(). Fix that in a such way to avoid hairy goto. Signed-off-by:
Leon Yu <chianglungyu@gmail.com> Signed-off-by:
Benjamin LaHaise <bcrl@kvack.org> Signed-off-by:
-
Chen Yucong authored
commit b985194c upstream. For handling a free hugepage in memory failure, the race will happen if another thread hwpoisoned this hugepage concurrently. So we need to check PageHWPoison instead of !PageHWPoison. If hwpoison_filter(p) returns true or a race happens, then we need to unlock_page(hpage). Signed-off-by:
Chen Yucong <slaoub@gmail.com> Reviewed-by:
Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Tested-by:
Andi Kleen <ak@linux.intel.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Mark Salter authored
commit 4797ec2d upstream. The following happens when trying to run a kvm guest on a kernel configured for 64k pages. This doesn't happen with 4k pages: BUG: failure at include/linux/mm.h:297/put_page_testzero()! Kernel panic - not syncing: BUG! CPU: 2 PID: 4228 Comm: qemu-system-aar Tainted: GF 3.13.0-0.rc7.31.sa2.k32v1.aarch64.debug #1 Call trace: [<fffffe0000096034>] dump_backtrace+0x0/0x16c [<fffffe00000961b4>] show_stack+0x14/0x1c [<fffffe000066e648>] dump_stack+0x84/0xb0 [<fffffe0000668678>] panic+0xf4/0x220 [<fffffe000018ec78>] free_reserved_area+0x0/0x110 [<fffffe000018edd8>] free_pages+0x50/0x88 [<fffffe00000a759c>] kvm_free_stage2_pgd+0x30/0x40 [<fffffe00000a5354>] kvm_arch_destroy_vm+0x18/0x44 [<fffffe00000a1854>] kvm_put_kvm+0xf0/0x184 [<fffffe00000a1938>] kvm_vm_release+0x10/0x1c [<fffffe00001edc1c>] __fput+0xb0/0x288 [<fffffe00001ede4c>] ____fput+0xc/0x14 [<fffffe00000d5a2c>] task_work_run+0xa8/0x11c [<fffffe0000095c14>] do_notify_resume+0x54/0x58 In arch/arm/kvm/mmu.c:unmap_range(), we end up doing an extra put_page() on the stage2 pgd which leads to the BUG in put_page_testzero(). This happens because a pud_huge() test in unmap_range() returns true when it should always be false with 2-level pages tables used by 64k pages. This patch removes support for huge puds if 2-level pagetables are being used. Signed-off-by:
Mark Salter <msalter@redhat.com> [catalin.marinas@arm.com: removed #ifndef around PUD_SIZE check] Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Anthony Iliopoulos authored
commit 9844f546 upstream. The invalidation is required in order to maintain proper semantics under CoW conditions. In scenarios where a process clones several threads, a thread operating on a core whose DTLB entry for a particular hugepage has not been invalidated, will be reading from the hugepage that belongs to the forked child process, even after hugetlb_cow(). The thread will not see the updated page as long as the stale DTLB entry remains cached, the thread attempts to write into the page, the child process exits, or the thread gets migrated to a different processor. Signed-off-by:
Anthony Iliopoulos <anthony.iliopoulos@huawei.com> Link: http://lkml.kernel.org/r/20140514092948.GA17391@server-36.huawei.corpSuggested-by:
Shay Goikhman <shay.goikhman@huawei.com> Acked-by:
Dave Hansen <dave.hansen@intel.com> Signed-off-by:
H. Peter Anvin <hpa@linux.intel.com> Signed-off-by:
-
Kirill A. Shutemov authored
commit dd18dbc2 upstream. It's critical for split_huge_page() (and migration) to catch and freeze all PMDs on rmap walk. It gets tricky if there's concurrent fork() or mremap() since usually we copy/move page table entries on dup_mm() or move_page_tables() without rmap lock taken. To get it work we rely on rmap walk order to not miss any entry. We expect to see destination VMA after source one to work correctly. But after switching rmap implementation to interval tree it's not always possible to preserve expected walk order. It works fine for dup_mm() since new VMA has the same vma_start_pgoff() / vma_last_pgoff() and explicitly insert dst VMA after src one with vma_interval_tree_insert_after(). But on move_vma() destination VMA can be merged into adjacent one and as result shifted left in interval tree. Fortunately, we can detect the situation and prevent race with rmap walk by moving page table entries under rmap lock. See commit 38a76013. Problem is that we miss the lock when we move transhuge PMD. Most likely this bug caused the crash[1]. [1] http://thread.gmane.org/gmane.linux.kernel.mm/96473 Fixes: 108d6642 ("mm anon rmap: remove anon_vma_moveto_tail") Signed-off-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reviewed-by:
Andrea Arcangeli <aarcange@redhat.com> Cc: Rik van Riel <riel@redhat.com> Acked-by:
Michel Lespinasse <walken@google.com> Cc: Dave Jones <davej@redhat.com> Cc: David Miller <davem@davemloft.net> Acked-by:
Johannes Weiner <hannes@cmpxchg.org> Signed-off-by:
-
Emmanuel Grumbach authored
commit c52666ae upstream. If the association is in progress while we suspend, the stack will be in a messed up state. Clean it before we suspend. This patch completes Johannes's patch: 1a1cb744 Author: Johannes Berg <johannes.berg@intel.com> mac80211: fix suspend vs. authentication race Fixes: 12e7f517 ("mac80211: cleanup generic suspend/resume procedures") Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Eliad Peller authored
commit c1fbb258 upstream. cfg80211 is notified about connection failures by __cfg80211_connect_result() call. However, this function currently does not free cfg80211 sme. This results in hanging connection attempts in some cases e.g. when mac80211 authentication attempt is denied, we have this function call: ieee80211_rx_mgmt_auth() -> cfg80211_rx_mlme_mgmt() -> cfg80211_process_auth() -> cfg80211_sme_rx_auth() -> __cfg80211_connect_result() but cfg80211_sme_free() is never get called. Fixes: ceca7b71 ("cfg80211: separate internal SME implementation") Signed-off-by:
Eliad Peller <eliadx.peller@intel.com> Signed-off-by:
-
Corey Minyard authored
commit eb6d78ec upstream. The OBF timer in KCS was not reset in one situation when error recovery was started, resulting in an immediate timeout. Reported-by:
Bodo Stroesser <bstroesser@ts.fujitsu.com> Signed-off-by:
Corey Minyard <cminyard@mvista.com> Signed-off-by:
-
Jiri Bohac authored
commit 98a01e77 upstream. On architectures with sizeof(int) < sizeof (long), the computation of mask inside apply_slack() can be undefined if the computed bit is > 32. E.g. with: expires = 0xffffe6f5 and slack = 25, we get: expires_limit = 0x20000000e bit = 33 mask = (1 << 33) - 1 /* undefined */ On x86, mask becomes 1 and and the slack is not applied properly. On s390, mask is -1, expires is set to 0 and the timer fires immediately. Use 1UL << bit to solve that issue. Suggested-by:
Deborah Townsend <dstownse@us.ibm.com> Signed-off-by:
Jiri Bohac <jbohac@suse.cz> Link: http://lkml.kernel.org/r/20140418152310.GA13654@midget.suse.czSigned-off-by:
-
