HD-audio doesn't support the bulk access.  Currently it works even
without this flag as implicitly assumed, but it's safer to set
explicitly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Although they can be written, handle a few verbs as read-only in
regmap interface: CONFIG_DEFAULT, CONV and CVT_CHAN_COUNT.  These are
either updated in PCM or HDMI management code in a volatile manner, or
just needed only as parameter, thus they don't need to be written at
resume sync.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The 16bit COEF read/write is pretty standard for many codecs, and they
can be cached in most cases -- more importantly, they need to be
restored at resume.  For making this easier, add the cache support to
regmap.  If the codec driver wants to cache the COEF access, set
codec->cache_coef flag and issue AC_VERB_GET_PROC_COEF with the coef
index in LSB 8 bits.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

HD-audio has quite a few asymmetrical ways of accessing verbs, and one
of typical ones is GET/SET_POWER_STATE verbs.  While it takes only the
power state for setting, it returns a combination of states for
getting.  For making the state handling simpler, this patch adds a
code to translate the value returned from GET_POWER_STATE to return
only the actual state or -1 for error.  In that way, the driver can
simplify the power state management.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

HD-audio spec is inconvenient regarding the handling of stereo volume
controls.  It can set and get only single channel at once (although
there is a special option to set the same value to both channels).
This patch provides a fake pseudo-register via the regmap access so
that the stereo channels can be read and written by a single call.
It'd be useful, for example, for implementing DAPM widgets.

A stereo amp pseudo register consists of the encoding like the normal
amp verbs but it has both SET_LEFT (bit 13) and SET_RIGHT (bit 12)
bits set.  The regmap reads and writes a 16bit value for this pseudo
register where the upper 8bit is for the right chanel and the lower
8bit for the left channel.

Note that the driver doesn't recognize conflicts when both stereo and
mono channel registers are mixed.  Mixing them would certainly confuse
the operation.  So, use carefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Like the previous patches, this patch converts also to the regmap, at
this time, the cached verb writes are the target.  But this conversion
needs a bit more caution than before.

- In the old code, we just record any verbs as is, and restore them at
  resume.  For the regmap scheme, this doesn't work, since a few verbs
  like AMP or DIGI_CONVERT are asymmetrical.  Such verbs are converted
  either to the dedicated function (snd_hda_regmap_xxx_amp()) or
  changed to the unified verb.

- Some verbs have to be declared as vendor-specific ones before
  accessing via regmap.

Also, the minor optimization with codec->cached_write flag is dropped
in a few places, as this would confuse the operation.  Further
optimizations will be brought in the later patches, if any.

This conversion ends up with a drop of significant amount of codes,
mostly the helper codes that are no longer used.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Codecs may have own vendor-specific verbs, and we need to allow each
driver to give such verbs for cached accesses.  Here a verb can be put
into a single array and looked through it at readable and writeable
callbacks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The amp hash table was used for recording the cached reads of some
capability values like pin caps or amp caps.  Now all these are moved
to regmap as well.

One addition to the regmap helper is codec->caps_overwriting flag.
This is set in snd_hdac_override_parm(), and the regmap helper accepts
any register while this flag is set, so that it can overwrite even the
read-only verb like AC_VERB_PARAMETERS.  The flag is cleared
immediately in snd_hdac_override_parm(), as it's a once-off flag.

Along with these changes, the no longer needed amp hash and relevant
fields are removed from hda_codec struct now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This patch converts the amp access functions to the regmap helpers.
The amp values were formerly cached in the own hash table.  Now it's
dropped by the regmap's cache.

The only tricky conversion is snd_hda_codec_amp_init().  This function
shouldn't do anything if the amp was already initialized.  For
achieving this behavior, a value is read once at first temporarily in
the cache-only mode.  Only if it returns an error,  i.e. the item
still doesn't exist in the cache, it proceeds to the update.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Sometimes we need the uncached reads, e.g. for refreshing the tree.
This patch provides the helper function for that and uses it for
refreshing widgets, reading subtrees and the whole proc reads.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Let's start converting the access functions to regmap.
The first one is the simplest, just converting the codec parameter
read helper function snd_hda_param_read().
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This patch adds an infrastructure to support regmap-based verb
accesses.  Because o the asymmetric nature of HD-audio verbs,
especially the amp verbs, we need to translate the verbs as a sort of
pseudo registers to be mapped uniquely in regmap.

In this patch, a pseudo register is built from the NID, the
AC_VERB_GET_* and 8bit parameters, i.e. almost in the form to be sent
to HD-audio bus but without codec address field.  OTOH, for writing,
the same pseudo register is translated to AC_VERB_SET_* automatically.
The AC_VERB_SET_AMP_* verb is re-encoded from the corresponding
AC_VERB_GET_AMP_* verb and parameter at writing.

Some verbs has a single command for read but multiple for writes.  A
write for such a verb is split automatically to multiple verbs.

The patch provides also a few handy helper functions.  They are
designed to be accessible even without regmap.  When no regmap is set
up (e.g. before the codec device instantiation), the direct hardware
access is used.  Also, it tries to avoid the unnecessary power-up.
The power up/down sequence is performed only on demand.

The codec driver needs to call snd_hdac_regmap_exit() and
snd_hdac_regmap_exit() at probe and remove if it wants the regmap
access.

There is one flag added to hdac_device.  When the flag lazy_cache is
set, regmap helper ignores a write for a suspended device and returns
as if it was actually written.  It reduces the hardware access pretty
much, e.g. when adjusting the mixer volume while in idle.  This
assumes that the driver will sync the cache later at resume properly,
so use it carefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This will be used by the regmap support.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Now let's take the basic tracepoints back to the HD-audio driver.
The three bus tracepoints, hda_send_cmd, hda_get_response and
hda_unsol_event are revived but in a slightly different form.
Since we don't assign the card number there, print the bus device name
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When the driver is unloaded before the codec is bound, it still keeps
the runtime PM refcount up, and results in the unbalance.  This patch
covers these cases by introducing a flag indicating the runtime PM
initialization and handling the codec registration procedure more
properly.  It also fixes the missing input beep device as a gratis,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add an overriding exec_verb op to struct hdac_device so that the call
via snd_hdac_exec_verb() can switch to a different route depending on
the setup.  The codec driver sets this field so that it can handle the
errors or applying quirks appropriately.  Furthermore, this mechanism
will be used for smooth transition for the regmap support in later
patches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This patch changes the sysfs files assigned to the codec device on the
bus which were formerly identical with hwdep sysfs files.  Now it
shows only a few core parameter, vendor_id, subsystem_id, revision_id,
afg, mfg, vendor_name and chip_name.

In addition, now a widget tree is added to the bus device sysfs
directory for showing the widget topology and attributes.  It's just a
flat tree consisting of subdirectories named as the widget NID
including various attributes like widget capability bits.  The AFG
(usually NID 0x01) is always found there, and it contains always
amp_in_caps, amp_out_caps and power_caps files.  Each of these
attributes show a single value.  The rest are the widget nodes
belonging to that AFG.  Note that the child node might not start from
0x02 but from another value like 0x0a.

Each child node may contain caps, pin_caps, amp_in_caps, amp_out_caps,
power_caps and connections files.  The caps (representing the widget
capability bits) always contain a value.  The rest may contain
value(s) if the attribute exists on the node.  Only connections file
show multiple values while other attributes have zero or one single
value.

An example of ls -R output is like below:
% ls -R /sys/bus/hdaudio/devices/hdaudioC0D0/
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/:
01/  04/  07/  0a/  0d/  10/  13/  16/  19/  1c/  1f/  22/
02/  05/  08/  0b/  0e/  11/  14/  17/  1a/  1d/  20/  23/
03/  06/  09/  0c/  0f/  12/  15/  18/  1b/  1e/  21/

/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/01:
amp_in_caps  amp_out_caps  power_caps

/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/02:
amp_in_caps  amp_out_caps  caps  connections  pin_caps  pin_cfg
power_caps

/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/03:
.....
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Now some codes and functionalities of hda_codec struct are moved to
hdac_device struct.  A few basic attributes like the codec address,
vendor ID number, FG numbers, etc are moved to hdac_device, and they
are accessed like codec->core.addr.  The basic verb exec functions are
moved, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

A few basic codes for communicating over HD-audio bus are moved to
struct hdac_bus now.  It has only command and get_response ops in
addition to the unsolicited event handling.

Note that the codec-side tracing support is disabled temporarily
during this transition due to the code shuffling.  It will be
re-enabled later once when all pieces are settled down.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Define the common hd-audio driver and device types to bind over
snd_hda_bus_type publicly.  This allows to implement other type of
device and driver code over hd-audio bus.

Now both struct hda_codec and struct hda_codec_driver inherit these
new struct hdac_device and struct hdac_driver, respectively.

The bus registration is done in subsys_initcall() to assure it
before any other driver registrations.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Pull bugfix for md from Neil Brown:
 "One fix for md in 4.0-rc4

  Regression in recent patch causes crash on error path"

* tag 'md/4.0-rc4-fix' of git://neil.brown.name/md:
  md: fix problems with freeing private data after ->run failure.

Pull driver core fixes from Greg KH:
 "Here are two bugfixes for things reported.  One regression in kernfs,
  and another issue fixed in the LZ4 code that was fixed in the
  "upstream" codebase that solves a reported kernel crash

  Both have been in linux-next for a while"

* tag 'driver-core-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  LZ4 : fix the data abort issue
  kernfs: handle poll correctly on 'direct_read' files.

Pull char/misc fixes from Greg KH:
 "Here are three fixes for 4.0-rc5 that revert 3 PCMCIA patches that
  were merged in 4.0-rc1 that cause regressions.  So let's revert them
  for now and they will be reworked and resent sometime in the future.

  All have been tested in linux-next for a while"

* tag 'char-misc-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Revert "pcmcia: add a new resource manager for non ISA systems"
  Revert "pcmcia: fix incorrect bracketing on a test"
  Revert "pcmcia: add missing include for new pci resource handler"

Pull staging driver fixes from Greg KH:
 "Here are four small staging driver fixes, all for the vt6656 and
  vt6655 drivers, that resolve some reported issues with them.

  All of these patches have been in linux next for a while"

* tag 'staging-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  vt6655: Fix late setting of byRFType.
  vt6655: RFbSetPower fix missing rate RATE_12M
  staging: vt6656: vnt_rf_setpower: fix missing rate RATE_12M
  staging: vt6655: vnt_tx_packet fix dma_idx selection.

Pull tty/serial driver fix from Greg KH:
 "Here's a single 8250 serial driver that fixes a reported deadlock with
  the serial console and the tty driver.

  It's been in linux-next for a while now"

* tag 'tty-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: 8250_dw: Fix deadlock in LCR workaround

Pull USB / PHY driver fixes from Greg KH:
 "Here's a number of USB and PHY driver fixes for 4.0-rc5.

  The largest thing here is a revert of a gadget function driver patch
  that removes 500 lines of code.  Other than that, it's a number of
  reported bugs fixes and new quirk/id entries.

  All have been in linux-next for a while"

* tag 'usb-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
  usb: common: otg-fsm: only signal connect after switching to peripheral
  uas: Add US_FL_NO_ATA_1X for Initio Corporation controllers / devices
  USB: ehci-atmel: rework clk handling
  MAINTAINERS: add entry for USB OTG FSM
  usb: chipidea: otg: add a_alt_hnp_support response for B device
  phy: omap-usb2: Fix missing clk_prepare call when using old dt name
  phy: ti/omap: Fix modalias
  phy: core: Fixup return value of phy_exit when !pm_runtime_enabled
  phy: miphy28lp: Convert to devm_kcalloc and fix wrong sizof
  phy: miphy365x: Convert to devm_kcalloc and fix wrong sizeof
  phy: twl4030-usb: Remove redundant assignment for twl->linkstat
  phy: exynos5-usbdrd: Fix off-by-one valid value checking for args->args[0]
  phy: Find the right match in devm_phy_destroy()
  phy: rockchip-usb: Fixup rockchip_usb_phy_power_on failure path
  phy: ti-pipe3: Simplify ti_pipe3_dpll_wait_lock implementation
  phy: samsung-usb2: Remove NULL terminating entry from phys array
  phy: hix5hd2-sata: Check return value of platform_get_resource
  phy: exynos-dp-video: Kill exynos_dp_video_phy_pwr_isol function
  Revert "usb: gadget: zero: Add support for interrupt EP"
  Revert "xhci: Clear the host side toggle manually when endpoint is 'soft reset'"
  ...

Pull slave dmaengine fixes from Vinod Koul:
 "Four fixes for dw, pl08x, imx-sdma and at_hdmac driver.  Nothing
  unusual here, simple fixes to these drivers"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: pl08x: Define capabilities for generic capabilities reporting
  dmaengine: dw: append MODULE_ALIAS for platform driver
  dmaengine: imx-sdma: switch to dynamic context mode after script loaded
  dmaengine: at_hdmac: Fix calculation of the residual bytes

Pull power management and ACPI fixes from Rafael Wysocki:
 "These are fixes for recent regressions (PCI/ACPI resources and at91
  RTC locking), a stable-candidate powercap RAPL driver fix and two ARM
  cpuidle fixes (one stable-candidate too).

  Specifics:

   - Revert a recent PCI commit related to IRQ resources management that
     introduced a regression for drivers attempting to bind to devices
     whose previous drivers did not balance pci_enable_device() and
     pci_disable_device() as expected (Rafael J Wysocki).

   - Fix a deadlock in at91_rtc_interrupt() introduced by a typo in a
     recent commit related to wakeup interrupt handling (Dan Carpenter).

   - Allow the power capping RAPL (Running-Average Power Limit) driver
     to use different energy units for domains within one CPU package
     which is necessary to handle Intel Haswell EP processors correctly
     (Jacob Pan).

   - Improve the cpuidle mvebu driver's handling of Armada XP SoCs by
     updating the target residency and exit latency numbers for those
     chips (Sebastien Rannou).

   - Prevent the cpuidle mvebu driver from calling cpu_pm_enter() twice
     in a row before cpu_pm_exit() is called on the same CPU which
     breaks the core's assumptions regarding the usage of those
     functions (Gregory Clement)"

* tag 'pm+acpi-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  Revert "x86/PCI: Refine the way to release PCI IRQ resources"
  rtc: at91rm9200: double locking bug in at91_rtc_interrupt()
  powercap / RAPL: handle domains with different energy units
  cpuidle: mvebu: Update cpuidle thresholds for Armada XP SOCs
  cpuidle: mvebu: Fix the CPU PM notifier usage

Pull drm updates from Dave Airlie:
 "A bunch of fixes across drivers:

  radeon:
     disable two ended allocation for now, it breaks some stuff

  amdkfd:
     misc fixes

  nouveau:
     fix irq loop problem, add basic support for GM206 (new hw)

  i915:
     fix some WARNs people were seeing

  exynos:
     fix some iommu interactions causing boot failures"

* git://people.freedesktop.org/~airlied/linux:
  drm/radeon: drop ttm two ended allocation
  drm/exynos: fix the initialization order in FIMD
  drm/exynos: fix typo config name correctly.
  drm/exynos: Check for NULL dereference of crtc
  drm/exynos: IS_ERR() vs NULL bug
  drm/exynos: remove unused files
  drm/i915: Make sure the primary plane is enabled before reading out the fb state
  drm/nouveau/bios: fix i2c table parsing for dcb 4.1
  drm/nouveau/device/gm100: Basic GM206 bring up (as copy of GM204)
  drm/nouveau/device: post write to NV_PMC_BOOT_1 when flipping endian switch
  drm/nouveau/gr/gf100: fix some accidental or'ing of buffer addresses
  drm/nouveau/fifo/nv04: remove the loop from the interrupt handler
  drm/radeon: Changing number of compute pipe lines
  drm/amdkfd: Fix SDMA queue init. in non-HWS mode
  drm/amdkfd: destroy mqd when destroying kernel queue
  drm/i915: Ensure plane->state->fb stays in sync with plane->fb

Merge tag 'devicetree-fixes-for-4.0-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux

Pull more DeviceTree fixes vfom Rob Herring:

 - revert setting stdout-path as preferred console.  This caused
   regressions in PowerMACs and other systems.

 - yet another fix for stdout-path option parsing.

 - fix error path handling in of_irq_parse_one

* tag 'devicetree-fixes-for-4.0-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  Revert "of: Fix premature bootconsole disable with 'stdout-path'"
  of: handle both '/' and ':' in path strings
  of: unittest: Add option string test case with longer path
  of/irq: Fix of_irq_parse_one() returned error codes

Pull SCSI target fixes from Nicholas Bellinger:
 "Here are current target-pending fixes for v4.0-rc5 code that have made
  their way into the queue over the last weeks.

  The fixes this round include:

   - Fix long-standing iser-target logout bug related to early
     conn_logout_comp completion, resulting in iscsi_conn use-after-tree
     OOpsen.  (Sagi + nab)

   - Fix long-standing tcm_fc bug in ft_invl_hw_context() failure
     handing for DDP hw offload.  (DanC)

   - Fix incorrect use of unprotected __transport_register_session() in
     tcm_qla2xxx + other single local se_node_acl fabrics.  (Bart)

   - Fix reference leak in target_submit_cmd() -> target_get_sess_cmd()
     for ack_kref=1 failure path.  (Bart)

   - Fix pSCSI backend ->get_device_type() statistics OOPs with
     un-configured device.  (Olaf + nab)

   - Fix virtual LUN=0 target_configure_device failure OOPs at modprobe
     time.  (Claudio + nab)

   - Fix FUA write false positive failure regression in v4.0-rc1 code.
     (Christophe Vu-Brugier + HCH)"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  target: do not reject FUA CDBs when write cache is enabled but emulate_write_cache is 0
  target: Fix virtual LUN=0 target_configure_device failure OOPs
  target/pscsi: Fix NULL pointer dereference in get_device_type
  tcm_fc: missing curly braces in ft_invl_hw_context()
  target: Fix reference leak in target_get_sess_cmd() error path
  loop/usb/vhost-scsi/xen-scsiback: Fix use of __transport_register_session
  tcm_qla2xxx: Fix incorrect use of __transport_register_session
  iscsi-target: Avoid early conn_logout_comp for iser connections
  Revert "iscsi-target: Avoid IN_LOGOUT failure case for iser-target"
  target: Disallow changing of WRITE cache/FUA attrs after export

Pull devicemapper fixes from Mike Snitzer:
 "A handful of stable fixes for DM:
   - fix thin target to always zero-fill reads to unprovisioned blocks
   - fix to interlock device destruction's suspend from internal
     suspends
   - fix 2 snapshot exception store handover bugs
   - fix dm-io to cope with DISCARD and WRITE_SAME capabilities changing"

* tag 'dm-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm io: deal with wandering queue limits when handling REQ_DISCARD and REQ_WRITE_SAME
  dm snapshot: suspend merging snapshot when doing exception handover
  dm snapshot: suspend origin when doing exception handover
  dm: hold suspend_lock while suspending device during device deletion
  dm thin: fix to consistently zero-fill reads to unprovisioned blocks

Pull btrfs fixes from Chris Mason:
 "Most of these are fixing extent reservation accounting, or corners
  with tree writeback during commit.

  Josef's set does add a test, which isn't strictly a fix, but it'll
  keep us from making this same mistake again"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix outstanding_extents accounting in DIO
  Btrfs: add sanity test for outstanding_extents accounting
  Btrfs: just free dummy extent buffers
  Btrfs: account merges/splits properly
  Btrfs: prepare block group cache before writing
  Btrfs: fix ASSERT(list_empty(&cur_trans->dirty_bgs_list)
  Btrfs: account for the correct number of extents for delalloc reservations
  Btrfs: fix merge delalloc logic
  Btrfs: fix comp_oper to get right order
  Btrfs: catch transaction abortion after waiting for it
  btrfs: fix sizeof format specifier in btrfs_check_super_valid()

Pull nfsd bufix from Bruce Fields:
 "This is a fix for a crash easily triggered by 4.1 activity to a server
  built with CONFIG_NFSD_PNFS.

  There are some more bugfixes queued up that I intend to pass along
  next week, but this is the most critical"

* 'for-4.0' of git://linux-nfs.org/~bfields/linux:
  Subject: nfsd: don't recursively call nfsd4_cb_layout_fail

Pull UBI fix from Artem Bityutskiy:
 "This fixes a bug introduced during the v4.0 merge window where we
  forgot to put braces where they should be"

* tag 'upstream-4.0-rc5' of git://git.infradead.org/linux-ubifs:
  UBI: fix missing brace control flow

Pull arm64 fixes from Catalin Marinas:

 - mm switching fix where the kernel pgd ends up in the user TTBR0 after
   returning from an EFI run-time services call

 - fix __GFP_ZERO handling for atomic pool and CMA DMA allocations (the
   generic code does get the gfp flags, so it's left with the arch code
   to memzero accordingly)

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: Honor __GFP_ZERO in dma allocations
  arm64: efi: don't restore TTBR0 if active_mm points at init_mm

Pull ARM fixes from Russell King:
 "Another few ARM fixes.  Fabrice fixed the L2 cache DT parsing to allow
  prefetch configuration to be specified even when the cache size
  parsing fails.

  Laura noticed that the setting of page attributes wasn't working for
  modules due to is_module_addr() always returning false.

  Marc Gonzalez (aka Mason) noticed a potential latent bug with the way
  we read one of the CPUID registers (where we could attempt to read a
  non-present CPUID register which may fault.)

  I've fixed an issue where 32-bit DMA masks were failing with memory
  which extended to the top of physical address space, and I've also
  added debugging output of the page tables when we hit a data access
  exception which we don't specifically handle - prompted by the lack of
  information in a bug report"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8313/1: Use read_cpuid_ext() macro instead of inline asm
  ARM: 8311/1: Don't use is_module_addr in setting page attributes
  ARM: 8310/1: l2c: Fix prefetch settings dt parsing
  ARM: dump pgd, pmd and pte states on unhandled data abort faults
  ARM: dma-api: fix off-by-one error in __dma_supported()

* pm-cpuidle:
  cpuidle: mvebu: Update cpuidle thresholds for Armada XP SOCs
  cpuidle: mvebu: Fix the CPU PM notifier usage

* powercap:
  powercap / RAPL: handle domains with different energy units

* irq-pm:
  rtc: at91rm9200: double locking bug in at91_rtc_interrupt()

* acpi-resources:
  Revert "x86/PCI: Refine the way to release PCI IRQ resources"