KVM_MEMSLOT_INCOHERENT is not used anymore, as we've killed its
only use in the arm/arm64 MMU code. Let's remove the last artifacts.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

Now that we unconditionally flush newly mapped pages to the PoC,
there is no need to care about the "uncached" status of individual
pages - they must all be visible all the way down.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

When we fault in a page, we flush it to the PoC (Point of Coherency)
if the faulting vcpu has its own caches off, so that it can observe
the page we just brought it.

But if the vcpu has its caches on, we skip that step. Bad things
happen when *another* vcpu tries to access that page with its own
caches disabled. At that point, there is no garantee that the
data has made it to the PoC, and we access stale data.

The obvious fix is to always flush to PoC when a page is faulted
in, no matter what the state of the vcpu is.

Cc: stable@vger.kernel.org
Fixes: 2d58b733 ("arm64: KVM: force cache clean on page fault when caches are off")
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

Update error code returned for Invalid CPU interface register
value and access in AArch32 mode.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

Userspace requires to store and restore of line_level for
level triggered interrupts using ioctl KVM_DEV_ARM_VGIC_GRP_LEVEL_INFO.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

VGICv3 CPU interface registers are accessed using
KVM_DEV_ARM_VGIC_CPU_SYSREGS ioctl. These registers are accessed
as 64-bit. The cpu MPIDR value is passed along with register id.
It is used to identify the cpu for registers access.

The VM that supports SEIs expect it on destination machine to handle
guest aborts and hence checked for ICC_CTLR_EL1.SEIS compatibility.
Similarly, VM that supports Affinity Level 3 that is required for AArch64
mode, is required to be supported on destination machine. Hence checked
for ICC_CTLR_EL1.A3V compatibility.

The arch/arm64/kvm/vgic-sys-reg-v3.c handles read and write of VGIC
CPU registers for AArch64.

For AArch32 mode, arch/arm/kvm/vgic-v3-coproc.c file is created but
APIs are not implemented.

Updated arch/arm/include/uapi/asm/kvm.h with new definitions
required to compile for AArch32.

The version of VGIC v3 specification is defined here
Documentation/virtual/kvm/devices/arm-vgic-v3.txt
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

ICC_VMCR_EL2 supports virtual access to ICC_IGRPEN1_EL1.Enable
and ICC_IGRPEN0_EL1.Enable fields. Add grpen0 and grpen1 member
variables to struct vmcr to support read and write of these fields.

Also refactor vgic_set_vmcr and vgic_get_vmcr() code.
Drop ICH_VMCR_CTLR_SHIFT and ICH_VMCR_CTLR_MASK macros and instead
use ICH_VMCR_EOI* and ICH_VMCR_CBPR* macros.
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

Define register definitions for ICH_VMCR_EL2, ICC_CTLR_EL1 and
ICH_VTR_EL2, ICC_BPR0_EL1, ICC_BPR1_EL1 registers.
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

In order to implement vGICv3 CPU interface access, we will need to perform
table lookup of system registers. We would need both index_to_params() and
find_reg() exported for that purpose, but instead we export a single
function which combines them both.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

VGICv3 Distributor and Redistributor registers are accessed using
KVM_DEV_ARM_VGIC_GRP_DIST_REGS and KVM_DEV_ARM_VGIC_GRP_REDIST_REGS
with KVM_SET_DEVICE_ATTR and KVM_GET_DEVICE_ATTR ioctls.
These registers are accessed as 32-bit and cpu mpidr
value passed along with register offset is used to identify the
cpu for redistributor registers access.

The version of VGIC v3 specification is defined here
Documentation/virtual/kvm/devices/arm-vgic-v3.txt

Also update arch/arm/include/uapi/asm/kvm.h to compile for
AArch32 mode.
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

Read and write of some registers like ISPENDR and ICPENDR
from userspace requires special handling when compared to
guest access for these registers.

Refer to Documentation/virtual/kvm/devices/arm-vgic-v3.txt
for handling of ISPENDR, ICPENDR registers handling.

Add infrastructure to support guest and userspace read
and write for the required registers
Also moved vgic_uaccess from vgic-mmio-v2.c to vgic-mmio.c
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

Add a file to debugfs to read the in-kernel state of the vgic.  We don't
do any locking of the entire VGIC state while traversing all the IRQs,
so if the VM is running the user/developer may not see a quiesced state,
but should take care to pause the VM using facilities in user space for
that purpose.

We also don't support LPIs yet, but they can be added easily if needed.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

One of the goals behind the VGIC redesign was to get rid of cached or
intermediate state in the data structures, but we decided to allow
ourselves to precompute the pending value of an IRQ based on the line
level and pending latch state.  However, this has now become difficult
to base proper GICv3 save/restore on, because there is a potential to
modify the pending state without knowing if an interrupt is edge or
level configured.

See the following post and related message for more background:
https://lists.cs.columbia.edu/pipermail/kvmarm/2017-January/023195.html

This commit gets rid of the precomputed pending field in favor of a
function that calculates the value when needed, irq_is_pending().

The soft_pending field is renamed to pending_latch to represent that
this latch is the equivalent hardware latch which gets manipulated by
the input signal for edge-triggered interrupts and when writing to the
SPENDR/CPENDR registers.

After this commit save/restore code should be able to simply restore the
pending_latch state, line_level state, and config state in any order and
get the desired result.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

Pull x86 fix from Thomas Gleixner:
 "Restore the retrigger callbacks in the IO APIC irq chips. That
  addresses a long standing regression which got introduced with the
  rewrite of the x86 irq subsystem two years ago and went unnoticed so
  far"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/ioapic: Restore IO-APIC irq_chip retrigger callback

Pull smp/hotplug fix from Thomas Gleixner:
 "Remove an unused variable which is a leftover from the notifier
  removal"

* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  cpu/hotplug: Remove unused but set variable in _cpu_down()

Pull virtio/vhost fixes from Michael Tsirkin:
 "Random fixes and cleanups that accumulated over the time"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio/s390: virtio: constify virtio_config_ops structures
  virtio/s390: add missing \n to end of dev_err message
  virtio/s390: support READ_STATUS command for virtio-ccw
  tools/virtio/ringtest: tweaks for s390
  tools/virtio/ringtest: fix run-on-all.sh for offline cpus
  virtio_console: fix a crash in config_work_handler
  vhost/scsi: silence uninitialized variable warning
  vhost: scsi: constify target_core_fabric_ops structures

Pull thermal management fixes from Zhang Rui:

 - fix a regression that thermal zone dynamically allocated sysfs
   attributes are freed before they're removed, which is introduced in
   4.10-rc1 (Jacob von Chorus)

 - fix a boot warning because deprecated hwmon API is used (Fabio
   Estevam)

 - a couple of fixes for rockchip thermal driver (Brian Norris, Caesar
   Wang)

* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  thermal: rockchip: fixes the conversion table
  thermal: core: move tz->device.groups cleanup to thermal_release
  thermal: thermal_hwmon: Convert to hwmon_device_register_with_info()
  thermal: rockchip: handle set_trips without the trip points
  thermal: rockchip: optimize the conversion table
  thermal: rockchip: fixes invalid temperature case
  thermal: rockchip: don't pass table structs by value
  thermal: rockchip: improve conversion error messages

Pull USB fixes from Greg KH:
 "Here are a few small USB fixes for 4.10-rc5.

  Most of these are gadget/dwc2 fixes for reported issues, all of these
  have been in linux-next for a while. The last one is a single xhci
  WARN_ON removal to handle an issue that the dwc3 driver is hitting in
  the 4.10-rc tree. The warning is harmless and needs to be removed, and
  a "real" fix that is more complex will show up in 4.11-rc1 for this
  device.

  That last patch hasn't been in linux-next yet due to the weekend
  timing, but it's a "simple" WARN_ON() removal so what could go wrong?
  :)"

Famous last words.

* tag 'usb-4.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  xhci: remove WARN_ON if dma mask is not set for platform devices
  usb: dwc2: host: fix Wmaybe-uninitialized warning
  usb: dwc2: gadget: Fix GUSBCFG.USBTRDTIM value
  usb: gadget: udc: atmel: remove memory leak
  usb: dwc3: exynos fix axius clock error path to do cleanup
  usb: dwc2: Avoid suspending if we're in gadget mode
  usb: dwc2: use u32 for DT binding parameters
  usb: gadget: f_fs: Fix iterations on endpoints.
  usb: dwc2: gadget: Fix DMA memory freeing
  usb: gadget: composite: Fix function used to free memory

Pull libnvdimm fixes from Dan Williams:
 "Two fixes:

   - a regression fix for the multiple-pmem-namespace-per-region support
     added in 4.9. Even if an existing environment is not using that
     feature the act of creating and a destroying a single namespace
     with the ndctl utility will lead to the proliferation of extra
     unwanted namespace devices.

   - a fix for the error code returned from the pmem driver when the
     memcpy_mcsafe() routine returns -EFAULT. Btrfs seems to be the only
     block I/O consumer that tries to parse the meaning of the error
     code when it is non-zero.

  Neither of these fixes are critical, the namespace leak is awkward in
  that it can cause device naming to change and complicates debugging
  namespace initialization issues. The error code fix is included out of
  caution for what other consumers might be expecting -EIO for block I/O
  errors"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  libnvdimm, namespace: fix pmem namespace leak, delete when size set to zero
  pmem: return EIO on read_pmem() failure

Pull clk fix from Stephen Boyd:
 "One fix for Samsung Exynos524x SoCs where recent IOMMU patches have
  caused some of these clocks to turn off when they were always left on
  before"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk/samsung: exynos542x: mark some clocks as critical

Pull ARC fixes from Vineet Gupta:

 - more intc updates [Yuriv]

 - fix module build when unwinder is turned off

 - IO Coherency Programming model updates

 - other miscellaneous

* tag 'arc-4.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: Revert "ARC: mm: IOC: Don't enable IOC by default"
  ARC: mm: split arc_cache_init to allow __init reaping of bulk
  ARCv2: IOC: Use actual memory size to setup aperture size
  ARCv2: IOC: Adhere to progamming model guidelines to avoid DMA corruption
  ARCv2: IOC: refactor the IOC and SLC operations into own functions
  ARC: module: Fix !CONFIG_ARC_DW2_UNWIND builds
  ARCv2: save r30 on kernel entry as gcc uses it for code-gen
  ARCv2: IRQ: Call entry/exit functions for chained handlers in MCIP
  ARC: IRQ: Use hwirq instead of virq in mask/unmask
  ARC: mmu: clarify the MMUv3 programming model

Pull powerpc fixes from Michael Ellerman:
 "Two fixes for fallout from the hugetlb changes we merged this cycle.

  Ten other fixes, four only affect Power9, and the rest are a bit of a
  mixture though nothing terrible.

  Thanks to: Aneesh Kumar K.V, Anton Blanchard, Benjamin Herrenschmidt,
  Dave Martin, Gavin Shan, Madhavan Srinivasan, Nicholas Piggin, Reza
  Arbab"

* tag 'powerpc-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc: Ignore reserved field in DCSR and PVR reads and writes
  powerpc/ptrace: Preserve previous TM fprs/vsrs on short regset write
  powerpc/ptrace: Preserve previous fprs/vsrs on short regset write
  powerpc/perf: Use MSR to report privilege level on P9 DD1
  selftest/powerpc: Wrong PMC initialized in pmc56_overflow test
  powerpc/eeh: Enable IO path on permanent error
  powerpc/perf: Fix PM_BRU_CMPL event code for power9
  powerpc/mm: Fix little-endian 4K hugetlb
  powerpc/mm/hugetlb: Don't panic when we don't find the default huge page size
  powerpc: Fix pgtable pmd cache init
  powerpc/icp-opal: Fix missing KVM case and harden replay
  powerpc/mm: Fix memory hotplug BUG() on radix

Pull KVM fixes from Radim Krčmář:
 "ARM:
   - Fix for timer setup on VHE machines
   - Drop spurious warning when the timer races against the vcpu running
     again
   - Prevent a vgic deadlock when the initialization fails (for stable)

  s390:
   - Fix a kernel memory exposure (for stable)

  x86:
   - Fix exception injection when hypercall instruction cannot be
     patched"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: s390: do not expose random data via facility bitmap
  KVM: x86: fix fixing of hypercalls
  KVM: arm/arm64: vgic: Fix deadlock on error handling
  KVM: arm64: Access CNTHCTL_EL2 bit fields correctly on VHE systems
  KVM: arm/arm64: Fix occasional warning from the timer work function

Merge branch 'scsi-target-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/bvanassche/linux

Pull SCSI target fixes from Bart Van Assche:

 - two small fixes for the ibmvscsis driver

 - ten patches with bug fixes for the target mode of the qla2xxx driver

 - four patches that avoid that the "sparse" and "smatch" static
   analyzer tools report false positives for the qla2xxx code base

* 'scsi-target-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/bvanassche/linux:
  qla2xxx: Disable out-of-order processing by default in firmware
  qla2xxx: Fix erroneous invalid handle message
  qla2xxx: Reduce exess wait during chip reset
  qla2xxx: Terminate exchange if corrupted
  qla2xxx: Fix crash due to null pointer access
  qla2xxx: Collect additional information to debug fw dump
  qla2xxx: Reset reserved field in firmware options to 0
  qla2xxx: Set tcm_qla2xxx version to automatically track qla2xxx version
  qla2xxx: Include ATIO queue in firmware dump when in target mode
  qla2xxx: Fix wrong IOCB type assumption
  qla2xxx: Avoid that building with W=1 triggers complaints about set-but-not-used variables
  qla2xxx: Move two arrays from header files to .c files
  qla2xxx: Declare an array with file scope static
  qla2xxx: Fix indentation
  ibmvscsis: Fix sleeping in interrupt context
  ibmvscsis: Fix max transfer length

Pull block fixes from Jens Axboe:
 "Just two small fixes for this -rc.

  One is just killing an unused variable from Keith, but the other
  fixes a performance regression for nbd in this series, where we
  inadvertently flipped when we set MSG_MORE when outputting data"

* 'for-linus' of git://git.kernel.dk/linux-block:
  nbd: only set MSG_MORE when we have more to send
  blk-mq: Remove unused variable

Pull spi fixes from Mark Brown:
 "The usual small smattering of driver specific fixes. A few bits that
  stand out here:

   - the R-Car patches adding fallbacks are just adding new compatible
     strings to the driver so that device trees are written in a more
     robustly future proof fashion, this isn't strictly a fix but it's
     just new IDs and it's better to get it into mainline sooner to
     improve the ABI

   - the DesignWare "switch to new API part 2" patch is actually a
     misleadingly titled fix for a bit that got missed in the original
     conversion"

* tag 'spi-fix-v4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: davinci: use dma_mapping_error()
  spi: spi-axi: Free resources on error path
  spi: pxa2xx: add missed break
  spi: dw-mid: switch to new dmaengine_terminate_* API (part 2)
  spi: dw: Make debugfs name unique between instances
  spi: sh-msiof: Do not use C++ style comment
  spi: armada-3700: Set mode bits correctly
  spi: armada-3700: fix unsigned compare than zero on irq
  spi: sh-msiof: Add R-Car Gen 2 and 3 fallback bindings
  spi: SPI_FSL_DSPI should depend on HAS_DMA

Pull ceph fixes from Ilya Dryomov:
 "Three filesystem endianness fixes (one goes back to the 2.6 era, all
  marked for stable) and two fixups for this merge window's patches"

* tag 'ceph-for-4.10-rc5' of git://github.com/ceph/ceph-client:
  ceph: fix bad endianness handling in parse_reply_info_extra
  ceph: fix endianness bug in frag_tree_split_cmp
  ceph: fix endianness of getattr mask in ceph_d_revalidate
  libceph: make sure ceph_aes_crypt() IV is aligned
  ceph: fix ceph_get_caps() interruption

Pull overlayfs fix from Miklos Szeredi:
 "This fixes a regression introduced in this cycle"

* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  ovl: fix possible use after free on redirect dir lookup

Pull fuse fixes from Miklos Szeredi:
 "Fix two regressions, one introduced in 4.9 and a less recent one in
  4.2"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: fix time_to_jiffies nsec sanity check
  fuse: clear FR_PENDING flag when moving requests out of pending queue

Pull SCSI fixes from James Bottomley:
 "This is a set of 12 fixes including the mpt3sas one that was causing
  hangs on ATA passthrough.

  The others are a couple of zoned block device fixes, a SAS device
  detection bug which lead to SATA drives not being matched to bays, two
  qla2xxx MSI fixes, a qla2xxx req for rsp confusion caused by cut and
  paste, and a few other minor fixes"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: mpt3sas: fix hang on ata passthrough commands
  scsi: lpfc: Set elsiocb contexts to NULL after freeing it
  scsi: sd: Ignore zoned field for host-managed devices
  scsi: sd: Fix wrong DPOFUA disable in sd_read_cache_type
  scsi: bfa: fix wrongly initialized variable in bfad_im_bsg_els_ct_request()
  scsi: ses: Fix SAS device detection in enclosure
  scsi: libfc: Fix variable name in fc_set_wwpn
  scsi: lpfc: avoid double free of resource identifiers
  scsi: qla2xxx: remove irq_affinity_notifier
  scsi: qla2xxx: fix MSI-X vector affinity
  scsi: qla2xxx: Fix apparent cut-n-paste error.
  scsi: qla2xxx: Get mutex lock before checking optrom_state

Pull arm64 fixes from Catalin Marinas:

 - avoid potential stack information leak via the ptrace ABI caused by
   uninitialised variables

 - SWIOTLB DMA API fall-back allocation fix when the SWIOTLB buffer is
   not initialised (all RAM is suitable for 32-bit DMA masks)

 - fix the bad_mode function returning for unhandled exceptions coming
   from user space

 - fix name clash in __page_to_voff()

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: avoid returning from bad_mode
  arm64/ptrace: Reject attempts to set incomplete hardware breakpoint fields
  arm64/ptrace: Avoid uninitialised struct padding in fpr_set()
  arm64/ptrace: Preserve previous registers for short regset write
  arm64/ptrace: Preserve previous registers for short regset write
  arm64/ptrace: Preserve previous registers for short regset write
  arm64: mm: avoid name clash in __page_to_voff()
  arm64: Fix swiotlb fallback allocation

KVM: s390: Fix for 4.10 (via kvm/master)

Fix a kernel memory exposure.

kvm_s390_get_machine() populates the facility bitmap by copying bytes
from the host results that are stored in a 256 byte array in the prefix
page. The KVM code does use the size of the target buffer (2k), thus
copying and exposing unrelated kernel memory (mostly machine check
related logout data).

Let's use the size of the source buffer instead.  This is ok, as the
target buffer will always be greater or equal than the source buffer as
the KVM internal buffers (and thus S390_ARCH_FAC_LIST_SIZE_BYTE) cover
the maximum possible size that is allowed by STFLE, which is 256
doublewords. All structures are zero allocated so we can leave bytes
256-2047 unchanged.

Add a similar fix for kvm_arch_init_vm().
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
[found with smatch]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
CC: stable@vger.kernel.org
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>

The warn on is a bit too much, we will anyway set the dma mask if not set
previously.

The main reason for this fix is that 4.10-rc1  has a dwc3 change that
pass a parent sysdev dev pointer instead of setting the dma mask of
its xhci platform device. xhci platform driver can then get more
attributes from the sysdev than just the dma mask.

The usb core and xhci changes are not yet in 4.10, and a fix like
this was preferred instead of taking those big changes this late in
the rc-cycle.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IBM bit 31 (for the rest of us - bit 0) is a reserved field in the
instruction definition of mtspr and mfspr. Hardware is encouraged to
(and does) ignore it.

As a result, if userspace executes an mtspr DSCR with the reserved bit
set, we get a DSCR facility unavailable exception. The kernel fails to
match against the expected value/mask, and we silently return to
userspace to try and re-execute the same mtspr DSCR instruction. We
loop forever until the process is killed.

We should do something here, and it seems mirroring what hardware does
is the better option vs killing the process. While here, relax the
matching of mfspr PVR too.

Cc: stable@vger.kernel.org
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET
to fill all the check pointed registers, the thread's old check pointed
registers are preserved.

Fixes: 9d3918f7 ("powerpc/ptrace: Enable support for NT_PPC_CVSX")
Fixes: 19cbcbf7 ("powerpc/ptrace: Enable support for NT_PPC_CFPR")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET
to fill all the registers, the thread's old registers are preserved.

Fixes: c6e6771b ("powerpc: Introduce VSX thread_struct and CONFIG_VSX")
Cc: stable@vger.kernel.org # v2.6.27+
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Pull ARM SoC fixes from Olof Johansson:
 "We've been sitting on fixes for a while, and they keep trickling in at
  a low rate. Nothing in here comes across as particularly scary or
  noteworthy, for the most part it's a large collection of small DT
  tweaks"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (24 commits)
  ARM: dts: da850-evm: fix read access to SPI flash
  ARM: dts: omap3: Fix Card Detect and Write Protect on Logic PD SOM-LV
  ARM64: dts: meson-gxbb-odroidc2: Disable SCPI DVFS
  ARM: dts: OMAP5 / DRA7: indicate that SATA port 0 is available.
  ARM: dts: NSP: Fix DT ranges error
  ARM: multi_v7_defconfig: set bcm47xx watchdog
  ARM: multi_v7_defconfig: fix config typo
  ARM: dts: dra72-evm-revc: fix typo in ethernet-phy node
  soc: ti: wkup_m3_ipc: Fix error return code in wkup_m3_ipc_probe()
  ARM: ux500: fix prcmu_is_cpu_in_wfi() calculation
  ARM: dts: sunxi: Change node name for pwrseq pin on Olinuxino-lime2-emmc
  ARM: dts: sun8i: Support DTB build for NanoPi M1
  ARM: dts: sun6i: hummingbird: Enable display engine again
  ARM: dts: sun6i: Disable display pipeline by default
  ARM, ARM64: dts: drop "arm,amba-bus" in favor of "simple-bus" part 3
  ARM: dts: imx6qdl-nitrogen6_som2: fix sgtl5000 pinctrl init
  ARM: dts: imx6qdl-nitrogen6_max: fix sgtl5000 pinctrl init
  ARM: OMAP1: DMA: Correct the number of logical channels
  ARM: dts: am335x-icev2: Remove the duplicated pinmux setting
  ARM: OMAP2+: Fix WL1283 Bluetooth Baud Rate
  ...