Remove SH_ETH_HAS_TSU #define's and #ifdef's. Set three 'struct net_device_ops'
methods that depend on the presence of TSU basing on the 'tsu' field of 'struct
sh_eth_cpu_data'.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
[Sergei: made two method assignments one-liners, added the changelog, reworded
the subject, changing the prefix.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove all the duplicate definitions of sh_eth_set_duplex() under  different
#ifdef's, leaving only one outside the #ifdef's. We have to annotate it with
'__maybe_unused' since it's called not from all SoC #ifdef blocks.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
[Sergei: annotated sh_eth_set_duplex() as '__maybe_unused', added the changelog,
reworded the subject, changing the prefix.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use now always available EDSR_ENALL instead of the bare number to set EDSR.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
[Sergei: added the changelog, reworded the subject, changing the prefix.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove #ifdef around 'enum EDSR_BIT' and 'enum GECMR_BIT', replacing it with the
comments on which SoCs these registers exist.

SH7757 also has EDSR, so add a comment about it to 'enum EDSR_BIT'.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
[Sergei: folded in the former patch #2, updated the changelog, reworded the
subject, changing the prefix.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	net/netfilter/nf_log.c

The conflict in nf_log.c is that in 'net' we added CONFIG_PROC_FS
protection around foo_proc_entry() calls to fix a build failure,
whereas in Pablo's tree a guard if() test around a call is
remove_proc_entry() was removed.  Trivially resolved.

Pablo Neira Ayuso says:

====================
The following patchset contains the first batch of
Netfilter/IPVS updates for your net-next tree, they are:

* Three patches with improvements and code refactorization
  for nfnetlink_queue, from Florian Westphal.

* FTP helper now parses replies without brackets, as RFC1123
  recommends, from Jeff Mahoney.

* Rise a warning to tell everyone about ULOG deprecation,
  NFLOG has been already in the kernel tree for long time
  and supersedes the old logging over netlink stub, from
  myself.

* Don't panic if we fail to load netfilter core framework,
  just bail out instead, from myself.

* Add cond_resched_rcu, used by IPVS to allow rescheduling
  while walking over big hashtables, from Simon Horman.

* Change type of IPVS sysctl_sync_qlen_max sysctl to avoid
  possible overflow, from Zhang Yanfei.

* Use strlcpy instead of strncpy to skip zeroing of already
  initialized area to write the extension names in ebtables,
  from Chen Gang.

* Use already existing per-cpu notrack object from xt_CT,
  from Eric Dumazet.

* Save explicit socket lookup in xt_socket now that we have
  early demux, also from Eric Dumazet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.

This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge.  Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>

CAP_LEN contains the size of the network packet we're queueing to
userspace, i.e. normally it is the same as the NFQA_PAYLOAD attribute len.

Include it only in the unlikely case when NFQA_PAYLOAD is truncated due
to copy_range limitations.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

For every packet queued, we check if configured copy_range
is 0, and treat that as 'copy entire packet'.

We can move this check to the queue configuration, and can
set copy_range appropriately.

Also, convert repetitive '0xffff - NLA_HDRLEN' to a macro.

[ queue initialization still used 0xffff, although its harmless
  since the initial setting is overwritten on queue config ]
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Pull networking fixes from David Miller:

 1) Fix timeouts with direct mode authentication in mac80211, from
    Stanislaw Gruszka.

 2) Aggregation sessions can deadlock in ath9k, from Felix Fietkau.

 3) Netfilter's xt_addrtype doesn't work with ipv6 due to route lookups
    creating undesirable cache entries, from Florian Westphal.

 4) Fix netfilter's ipt_ULOG from generating non-NULL terminated
    strings.

 5) Fix netdev transmit queue crashes in mac80211, from Johannes Berg.

 6) Fix copy and paste error in 802.11 stack that broke reporting of
    64-bit station tx statistics, from Felix Fietkau.

 7) When qlge_probe fails, it leaks the netdev.  Fix from Wei Yongjun.

 8) SKB control block (where we store the IP options information,
    amongst other things) must be cleared properly otherwise ICMP
    sending can crash for IP tunnels.  Fix from Eric Dumazet.

 9) Verification of Energy Efficient Ether support was coded wrongly,
    the test was inversed.  Fix from Giuseppe CAVALLARO.

10) TCP handles redirects improperly because the wrong flow key is used
    for the route lookup.  From Michal Kubecek.

11) Don't interpret MSG_CMSG_COMPAT from userspace, fix from Andy
    Lutomirski.

12) The new AF_VSOCK was missing from the lockdep string table, fix from
    Federico Vaga.

13) be2net doesn't handle checksumming of IP fragments properly, from
    Somnath Kotur.

14) Fix several bugs in the device address list code that lead to
    crashes and other misbehaviors.  From Jay Vosburgh.

15) Fix ipv6 segmentation handling of fragmented GRE tunnel traffic,
    from Pravin B Shalr.

16) Fix usage of stale policies in IPSEC layer, from Paul Moore.

17) Fix team driver dump of ports when there are a large number of them,
    from Jiri Pirko.

18) Fix softlockups in UDP ipv4 socket lookup causes by and error in the
    hlist_nulls_for_each_entry_rcu() macro.  From Eric Dumazet.

19) Fix several regressions added by the high rate accuracy changes to
    the htb packet scheduler.  From Eric Dumazet.

20) Fix DMA'ing onto the stack in esd_usb2 and peak_usb CAN drivers,
    from Olivier Sobrie and Marc Kleine-Budde.

21) Fix unremovable network devices due to missing route pointer
    installation in the per-device ipv6 address list entries.  From Gao
    feng.

22) Apply the tg3 5719 DMA workaround on 5720 chips as well, otherwise
    we get stalls.  From Nithin Sujir.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (68 commits)
  net_sched: htb: do not mix 1ns and 64ns time units
  net: fix sk_buff head without data area
  tg3: Add read dma workaround for 5720
  net: ethernet: xilinx_emaclite: set protocol selector bits when writing ANAR
  bnx2x: Fix bridged GSO for 57710/57711 chips
  net: fec: add fallback to random MAC address
  bnx2x: fix TCP offload for tunneling ipv4 over ipv6
  ipv6: assign rt6_info to inet6_ifaddr in init_loopback
  net/mlx4_core: Keep VF assigned MAC in the PF admin table
  net/mlx4_en: Handle unassigned VF MAC address correctly
  net/mlx4_core: Return -EPROBE_DEFER when a VF is probed before PF is sufficiently initialized
  net/mlx4_en: Fix adaptive moderation cq update
  net: can: peak_usb: Do not do dma on the stack
  net: can: esd_usb2: Do not do dma on the stack
  net: can: kvaser_usb: fix reception on "USBcan Pro" and "USBcan R" type hardware.
  net_sched: restore "overhead xxx" handling
  net: force a reload of first item in hlist_nulls_for_each_entry_rcu
  hyperv: Fix vlan_proto setting in netvsc_recv_callback()
  team: fix port list dump for big number of ports
  list: introduce list_first_entry_or_null
  ...

commit 56b765b7 ("htb: improved accuracy at high rates") added another
regression for low rates, because it mixes 1ns and 64ns time units.

So the maximum delay (mbuffer) was not 60 second, but 937 ms.

Lets convert all time fields to 1ns as 64bit arches are becoming the
norm.
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some symbols referenced only in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Read data directly from platform recource table
and do not use of_irq_to_resource().
Also use devm_request_and_ioremap() for probe
functions simplification.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This corrects an regression introduced by "net: Use 16bits for *_headers
fields of struct skbuff" when NET_SKBUFF_DATA_USES_OFFSET is not set. In
that case skb->tail will be a pointer whereas skb->transport_header
will be an offset from head. This is corrected by using wrappers that
ensure that comparisons and calculations are always made using pointers.

Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to the problem in pktgen, netpoll uses skb_tail_offset()
too, as the code is copied from pktgen.

Also use return values of skb_put() directly, this will simiplify
the code.
Reported-by: Thomas Graf <tgraf@suug.ch>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Daniel Borkmann <dborkmann@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb_set_network_header() expects an offset based on the data pointer
whereas skb_tail_offset() also includes the headroom. This resulted
in the ip header being written in a wrong location.

Use return values of skb_put() directly and rely on skb->len to
set mac, network, and transport header.

Cc: Simon Horman <horms@verge.net.au>
Cc: Daniel Borkmann <dborkmann@redhat.com>
Assisted-by: Daniel Borkmann <dborkmann@redhat.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Daniel Borkmann <dborkmann@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The newly added sun4i-emac driver causes a build error when
CONFIG_NET_POLL_CONTROLLER is set, because it attempts to
assign a pointer to netdev->poll_controller, which has
been replaced with ops->ndo_poll_controller in 2.6.31!

The correct assignment is present as well, so we just need
to remove the wrong one.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Maxime Ripard <maxime.ripard@anandra.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4_en_select_queue() uses __skb_tx_hash to select the transmit queue.
XPS settings are ignored by this. Instead, we can use __netdev_pick_tx
to select the transmit queue.

Compile test only.
Signed-off-by: govindarajulu.v <govindarajulu90@gmail.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4 driver has a suboptimal memory allocation strategy for regular
MTU=1500 frames, as it uses two page fragments :

One of 512 bytes and one of 1024 bytes.

This makes GRO less effective, as each GSO packet contains 8 MSS instead
of 16 MSS.

Performance of a single TCP flow gains 25 % increase with the following
patch.

Before patch :

A:~# netperf -H 192.168.0.2 -Cc
MIGRATED TCP STREAM TEST ...
Recv   Send    Send                          Utilization       Service Demand
Socket Socket  Message  Elapsed              Send     Recv     Send    Recv
Size   Size    Size     Time     Throughput  local    remote   local   remote
bytes  bytes   bytes    secs.    10^6bits/s  % S      % S      us/KB   us/KB

 87380  16384  16384    10.00      13798.47   3.06     4.20     0.436   0.598

After patch :

A:~# netperf -H 192.68.0.2 -Cc
MIGRATED TCP STREAM TEST ...
Recv   Send    Send                          Utilization       Service Demand
Socket Socket  Message  Elapsed              Send     Recv     Send    Recv
Size   Size    Size     Time     Throughput  local    remote   local   remote
bytes  bytes   bytes    secs.    10^6bits/s  % S      % S      us/KB   us/KB

 87380  16384  16384    10.00      17273.80   3.44     4.19     0.391   0.477
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Amir Vadai <amirv@mellanox.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet spotted that we have to check skb->head instead
of skb->data as skb->head points to the beginning of the
data area of the skbuff. Similarly, we have to initialize the
skb->head pointer, not skb->data in __alloc_skb_head.

After this fix, netlink crashes in the release path of the
sk_buff, so let's fix that as well.

This bug was introduced in (0ebd0ac5 net: add function to
allocate sk_buff head without data area).
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 091f0ea3 "tg3: Add New 5719 Read
DMA workaround" added a workaround for TX DMA stall on the 5719. This
workaround needs to be applied to the 5720 as well.

Cc: stable@vger.kernel.org
Reported-by: Roland Dreier <roland@purestorage.com>
Tested-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch improves the logic used by the mvneta driver to find a MAC
address for a particular interface. Until now, it was only looking at
the Device Tree, and if no address was found, was falling back to
generating a random MAC address.

This patch adds the intermediate solution of reading the MAC address
from the hardware registers, in case it has been set by the
bootloader. So the order is now:

 1) MAC address from the Device Tree
 2) MAC address from the hardware registers
 3) Random MAC address

This requires moving the MAC address initialization a little bit later
in the ->probe() code, because it now requires the hardware registers
to be remapped.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch sets the protocol selector bits (4:0) of the PHY's MII_ADVERTISE
register (ANAR) when writing ADVERTISE_ALL. The protocol selector bits are
indicating IEEE 803.3u support and are fixed / read-only on some PHYs. Not
setting them correctly on others (like TI DP83630) makes the PHY fall back
to 10M HDX mode which should be avoided.

Tested for TI DP83630 PHY on Microblaze platform.
Signed-off-by: Jens Renner <renner@efe-gmbh.de>
Tested-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

Just fixed a typo in emac_probe().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

76723bca "net: mv643xx_eth: add DT parsing support" added a
dummy mv643xx_eth_shared_of_probe() fallback function with a
typo.

This adds the missing semicolon so we can build without CONFIG_OF
again, and changes both dummy functions to the more conventional
"static inline" syntax, which can avoid potential problems with
the empty macro.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It was recently found out that GSO on 57710/57711 was broken, due to packets
being sent without a valid IP checksum.

Commit 057cf65e "bnx2x: Fix GSO for 57710/57711 chips" partially fixed this
issue, but failed to set the correct IP checksum when receiving GSO packets
via bridges, as such packets enter bnx2x_tx_split() and the FW flags needed
to calculate IP checksum were erroneously set in the incorrect
buffer descriptor.

This patch re-enables GSO in said scenario for 57710/57711 chips.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

====================
this is a pull-request for net-next/master. It consists of two patches
by Fabio Estevam, cleaning up the flexcan driver (remove default
pinctrl and switch to SIMPLE_DEV_PM_OPS). A patch by me to simplify the
Kconfig [1] handling for flexcan. And a patch by Jingoo Han that
converts the can drivers to use platform_{get,set}_drvdata().

[1] My patch touches arch/{arm,powerpc}, so I collected Acked-bys from
Arnd Bergmann, Shawn Guo and Benjamin Herrenschmidt.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull MMC fixes from Chris Ball:
 - sdhci-acpi: Fix initial runtime PM status, add more ACPI IDs
 - atmel-mci, omap_hsmmc: DT handling fixes
 - esdhc-imx: Fix SDIO IRQs, fix multiblock reads (both h/w errata)

* tag 'mmc-fixes-for-3.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
  mmc: omap_hsmmc: Skip platform_get_resource_byname() for dt case
  mmc: omap_hsmmc: convert to dma_request_slave_channel_compat
  mmc: omap_hsmmc: Fix the DT pbias workaround for MMC controllers 2 to 5
  mmc: sdhci-pci: add more device ids
  mmc: sdhci-acpi: add more device ids
  mmc: sdhci-acpi: fix initial runtime pm status
  mmc: atmel-mci: convert to dma_request_slave_channel_compat()
  mmc: sdhci-esdhc-imx: fix multiblock reads on i.MX53
  mmc: sdhci-esdhc-imx: Fix SDIO interrupts

Pull input fixes from Dmitry Torokhov:
 "Just a 2 small driver fixups here"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: wacom - fix a typo for Cintiq 22HDT
  Input: synaptics - fix sync lost after resume on some laptops

Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull kvm bugfixes from Gleb Natapov:
 "The bulk of the fixes is in MIPS KVM kernel<->userspace ABI.  MIPS KVM
  is new for 3.10 and some problems were found with current ABI.  It is
  better to fix them now and do not have a kernel with broken one"

* 'fixes' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: Fix race in apic->pending_events processing
  KVM: fix sil/dil/bpl/spl in the mod/rm fields
  KVM: Emulate multibyte NOP
  ARM: KVM: be more thorough when invalidating TLBs
  ARM: KVM: prevent NULL pointer dereferences with KVM VCPU ioctl
  mips/kvm: Use ENOIOCTLCMD to indicate unimplemented ioctls.
  mips/kvm: Fix ABI by moving manipulation of CP0 registers to KVM_{G,S}ET_ONE_REG
  mips/kvm: Use ARRAY_SIZE() instead of hardcoded constants in kvm_arch_vcpu_ioctl_{s,g}et_regs
  mips/kvm: Fix name of gpr field in struct kvm_regs.
  mips/kvm: Fix ABI for use of 64-bit registers.
  mips/kvm: Fix ABI for use of FPU.

Pull gfs2 fixes from Steven Whitehouse:
 "There are four patches this time.

  The first fixes a problem where the wrong descriptor type was being
  written into the log for journaled data blocks.

  The second fixes a race relating to the deallocation of allocator
  data.

  The third provides a fallback if kmalloc is unable to satisfy a
  request to allocate a directory hash table.

  The fourth fixes the iopen glock caching so that inodes are deleted in
  a more timely manner after rmdir/unlink"

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
  GFS2: Don't cache iopen glocks
  GFS2: Fall back to vmalloc if kmalloc fails for dir hash tables
  GFS2: Increase i_writecount during gfs2_setattr_size
  GFS2: Set log descriptor type for jdata blocks

Pull fuse fixes from Miklos Szeredi:
 "One patch fixes an Oops introduced in 3.9 with the readdirplus
  feature.  The rest are fixes for async-dio in 3.10"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: fix alignment in short read optimization for async_dio
  fuse: return -EIOCBQUEUED from fuse_direct_IO() for all async requests
  fuse: fix readdirplus Oops in fuse_dentry_revalidate
  fuse: update inode size and invalidate attributes on fallocate
  fuse: truncate pagecache range on hole punch
  fuse: allocate for_background dio requests based on io->async state

Pull microblaze fixes from Michal Simek:
 "One is fixing warning reported by sparse and the second warning was
  reported by Geert in his build regressions/improvements status update
  for -rc4."

* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Use static inline functions in cacheflush.h
  microblaze: Fix sparse warnings

If no valid MAC address could be obtained from the hardware,
fall back to a randomly generated one.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

FW was initialized with data from wrong header, this caused TSO packets
have wrong IP csum.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we don't need scope id, we should initialize it to zero.
Same for ->sin6_flowinfo.

Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 25fb6ca4
"net IPv6 : Fix broken IPv6 routing table after loopback down-up"
forgot to assign rt6_info to the inet6_ifaddr.
When disable the net device, the rt6_info which allocated
in init_loopback will not be destroied in __ipv6_ifa_notify.

This will trigger the waring message below
[23527.916091] unregister_netdevice: waiting for tap0 to become free. Usage count = 1
Reported-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netdev_create_hash() is only called from netdev_init() which is marked
__net_init.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

s/allocal/allocate/
Signed-off-by: Jens Renner <renner@efe-gmbh.de>
Acked-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>