This add an utilities function radeon_ib_bogus_add which will
save an ib into a list of ib which can then be dumped using
debugfs. Once dumped the ib is removed from the list. This
should allow to save & capute ib for further debugging.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This already simplifies code significally and makes it maintaible
in case of adding memory reclocking plus voltage changing in future.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

For usec delays use udelay instead of scheduling, this should
allow reclocking to happen faster.
Signed-off-by: Dave Airlie <airlied@redhat.com>

we need a constant sclk for i2c prescale.  Also,
get the current sclk when calculating prescale rather
than using the default sclk.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

- only r4xx/r5xx/rs6xx/rs740 have clock gating atom table,
so disable it on r6xx.  it's already disabled on r7xx
- check to make sure the clock_gating hook exists before
calling it.  This avoids a segfault on asics without
that function.
- remove unused static power management function.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

not hooked up yet.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The idea is to flag a power state with a certain type and use
that type to decide on what state to select.  On r6xx+, we
select a state and then transition between clock modes in that
state.  On pre-r6xx, we transition between states directly.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The general idea is to validate the current hw state
against the set of power states and select a power
state based on that.  This patch just pulls the power
states from the bios and prints the information.  It
is not currently hooked up in the actual power management
code.  Hooking it up will require reworking the the current
power state selection code and will be handled in a future
patch.

Additionally, we'd need to decide on some default lower
power states for cards without power tables.

v2 - increment state_index after checking for default state
v3 - fix typo in pm init on pre-atom cards, handle pre-atom
cards without x86 bioses
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Currently unused.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

V2: reorganize functions, fix modesetting calls
V3: rebase patch, use radeon's workqueue
V4: enable on tested chipsets only, request VBLANK IRQs
V5: enable PM on older hardware (IRQs, mode_fixup, dpms)
V6: use separate dynpm module parameter
V7: drop RADEON_ prefix, set minimum mode for dpms off
V8: update legacy encoder call, fix order in rs600 IRQ
V9: update compute_clocks call in legacy, not only DPMS_OFF
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Set the number of crtcs in rdev at crtc init and use it
whenever we need the crtc count rather than recalculating
it everytime.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Only flush the gpu caches before we submit a fence.
This leads to a small performance boost when we take
the extra gpu cache flushes out of the ddx and mesa.
Once this patch is in and the drm version is bumped,
we can remove the flushes from the ddx and drm.

Also, remove the extra cache flushes from the blit
routine.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Internal locking should be sufficent for all these cases.
Signed-off-by: Dave Airlie <airlied@redhat.com>

This is used in a lot of places in the atom encoder code.

While here fix the spelling of crtc_source_params.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

use a union for the atom args.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The panel on the Toshiba A300-1BU laptop does not like the
PLL dividers selected by the avivo pll algo, but works fine
using the older method.  Add a quirk to handle it.

Should fix fdo bug 26358.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>

Rework the pll algo selection so that the pll algo
in use can be selected more easily.  This allows
us to select different pll divider selection algos
for specific monitors that work better with one algo
or the other.  This is needed for the next patch which
adds an LVDS pll quirk for a specific notebook.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Switch some magic numbers to their proper defines.
The register header madness needs to be cleaned up
at some point.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Some servers hardcode an edid in rom so that they will
work properly with KVMs.  This is a port of the relevant
code from the ddx.

[airlied: reworked to validate edid at boot stage - and
remove special quirk, if there is a valid EDID in the BIOS rom
we'll just try and use it.]
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Some servers have two VGA ports but only report
one in the bios connector tables.  On these systems
always set up the TV DAC so that it displays properly
even if the bios is wrong.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

wire hw i2c support into radeon i2c algo.

fixes merged:
- handle bus probing correctly
- use meaningful error numbers
- abort if transaction fails
- The line mapping is different depending on the asic.
- protect hw i2c engine with a mutex
- rs300 doesn't have a pin select bit
- r200 has a different pin select setup
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Currently just a wrapper around bit algo
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This was incorrect according to the docs and the UMS driver does
it like this.
Signed-off-by: Dave Airlie <airlied@redhat.com>

Boot testing on my rs480 laptop found the MC idle never happened
on startup, a quick check with AMD found the idle bit is in a different
place on the rs4xx than r300.

Implement a new rs400 mc idle function to fix this.
Signed-off-by: Dave Airlie <airlied@redhat.com>

this was incorrect on my rs480.
Signed-off-by: Dave Airlie <airlied@redhat.com>

Support isn't correct yet and we are getting green tinges on the
displays.
Signed-off-by: Dave Airlie <airlied@redhat.com>

In suspend path we unmap the GART table while in cleaning up
path we will unbind buffer and thus try to write to unmapped
GART leading to oops. In order to avoid this we don't call the
suspend path in cleanup path. Cleanup path is clever enough
to desactive GPU like the suspend path is doing, thus this was
redondant.

Tested on: RV370, R420, RV515, RV570, RV610, RV770 (all PCIE)
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drivers/gpu/drm/radeon/radeon_combios.c: In function 'radeon_combios_get_lvds_info':
drivers/gpu/drm/radeon/radeon_combios.c:893: warning: comparison is always false due to limited range of data type

Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Fix ati_pcigart printk format warning:

drivers/gpu/drm/ati_pcigart.c:115: warning: format '%Lx' expects type 'long long unsigned int', but argument 3 has type 'dma_addr_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Cache flush is required in case CPU is accessing rendered data.

This fixes glean/readPixSanity test case and random rendering
errors in sauerbraten and warzone2100.

v2 Fix comment ordering in r100_fence_ring_emit and remove extra
   defines added in first version.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

It seems that some R6XX/R7XX silently ignore HDP flush when
programmed through ring, this patch addback an ioctl callback
to allow R6XX/R7XX hw to perform such flush through MMIO in
order to fix a regression. For more details see:

http://bugzilla.kernel.org/show_bug.cgi?id=15186Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

VGA might be overwritting VRAM and corrupt our blit shader leading
to corruption, it likely won't happen if you load fbcon right after
radeon. Thanks to Shawn Starr and Andre Maasikas for tracking down
this issue.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

If radeon_cs_parser_init() fails, radeon_cs_ioctl() calls
radeon_cs_parser_fini() with the non-zero error value. The latter dereferenced
parser->ib which hasn't been initialized yet -> boom. Add a test for parser->ib
being non-NULL before dereferencing it.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

We are happy enough that the KMS driver is stable enough for enough people
for the kms enable/disable to leave staging. Distros can now contemplate
turning this on.
Signed-off-by: Dave Airlie <airlied@redhat.com>

If an error happen in r600_blit_prepare_copy report it rather
than WARNING and keeping execution. For instance if ib allocation
failed we did just warn about but then latter tried to access
NULL ib ptr causing oops. This patch also protect r600_copy_blit
with a mutex as otherwise one process might overwrite blit temporary
data with new one possibly leading to GPU lockup.

Should partialy or totaly fix:
https://bugzilla.redhat.com/show_bug.cgi?id=553279

V2 failing blit initialization is not fatal, fallback to memcpy when
this happen
V3 init blit before startup as we pin in startup, remove duplicate
code (this one was actualy tested unlike V2)
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This fixes the driver not loading on older versions of VMware.
Signed-off-by: Peter Hanzel <hanzelpeter@gmail.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>